Bandit IV AB M089 89


{Change Comments ***********************************************************}

{6/15/90
Modified: Bandit IV AB (W/*) M089.54
Updated to 3.2 Version per Fanuc 6M M001.72.1
JR}

{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}

{4/26/91,
Modified: Bandit IV AB (W/*) M089.73
For: Gibbs & Associates
Updated to new 4.0 Version per Fanuc 6M M001.80
DWB}

{6/21/96, Updated Bandit IV AB (W/*) M089.79 to .89 format per Fanuc 6M M001.89, JR}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '##0;'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(CallMasterNum#,5)
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'; SUB NUMBER: ' Program# EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'; OPERATION ' Operation# ': ' OperationType$ EOL
END
IF OperationComment?
'; ' OperationComment$ EOL
END
IF WorkGroupComment?
'; ' WorkGroupComment$ EOL
END
IF ToolTypeComment?
'; TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ EOL
END
IF ToolComment?
'; ' ToolComment$ EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC FeedC ZIn FeedEntC EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
EOR EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'; WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqC CallLab RepLab RepsLess1 EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
EOR EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqC 'G45' SetWFO EOL
SeqC CallLab EOL
IncWFO
NextWFO
ELSE
SeqC CallLab RepLab PartsLess1 EOL
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
EOR EOL
CloseSub
SeqC 'G45' WFO1 EOL
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
EOR EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqC AbsValue EOL
END
RETURN

FormatArc:
IF ArcCW?
CWArc
ELSE
CCWArc
END
MoveXYZC ArcIJ
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
SeqC DoAbsOrInc EOL
IF RapidFeat?
IF LastFeat?
SeqC CRCOffC EOL
SeqC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC EOL
SeqC RapidC MoveXYZC EOL
END
END
END
ELSE
IF LineFeat?
IF LastFeat?
SeqC CRCOffC EOL
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
SeqC CRCOnC EOL
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC FeedC MoveXYZC FeedRateC EOL
END
END
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
SeqC CRCOffC
IF NOT EmptyLine?
EOL
SeqC FeedC LastFeatExtend
END
EOL
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
ELSE
SeqC 'G45O' NewWFO# EOL
END
ELSE
IF FirstOperation?
IF NeedWFO1?
SeqC 'G45O' NewWFO# EOL
END
END
END
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SeqC AbsOrInc EOL
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
SeqC
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
EOL
END
SeqC EndSub EOL
EOR EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqC AbsOrInc EOL
SeqC Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC IncValue EOL
SeqC Feed StrtPosC EOL
SeqC AbsOrInc EOL
END
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC IncValue EOL
SeqC Rapid StrtPosC EOL
IF FeedEntry?
SeqC AbsOrInc ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqC Rapid ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
SeqC EndSub EOL
EOR EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqC CallLab EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqC EndSub EOL
EOR EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
SetMaxFeed('500')
SetFlagF('1') { Milling ZShiftOnly SepSubs }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramNameComment?
'; ' ProgramName$ EOL
END
IF ProgramComment?
'; ' ProgramComment$ EOL
END
IF FormatNameComment?
'; FORMAT: ' FormatName$ EOL
END
IF TimeComment?
'; ' Date$ ' AT ' Time$ EOL
END
IF MovesComment?
'; OUTPUT IN ' MoveType$ ' INCHES' EOL
END
IF PartsComment?
'; PARTS PROGRAMMED: ' Parts# EOL
END
IF StartToolComment?
'; FIRST TOOL NOT IN SPINDLE' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
SeqC 'G99' EOL
SeqC Plane EOL
DoPostScript
WFOStuff
SeqC Rapid 'X0Y0' EOL
SeqC AbsOrInc EOL
SeqC Preset 'X0Y0' EOL
DoOpComments
SeqC CoolOn EOL
SeqC SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC Rapid StrtPos EOL
SeqC ToolOfst ZCP1 EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
SeqC SpinOff EOL
SeqC 'GZO' EOL
IF ToolChangeAtHome?
SeqC Rapid Home EOL
END
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
SeqC ProgStop EOL
END

{Start new Operation}

DoOpComments
SeqC PlaneC EOL
DoPostScript
WFOStuff
SeqC CoolOn EOL
SeqC SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC Rapid StrtPos EOL
SeqC ToolOfst ZCP1 EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF SameTool?

{Finish off last Operation}

IF LAST ProgStop? OR NewToolOffset?
SeqC 'O0' EOL
END
DoEndOpPS
IF LAST ProgStop?
SeqC SpinOff EOL
SeqC 'M00' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
END

{Start new Operation}

DoOpComments
DoPostScript
CheckPass
SeqC PlaneC EOL
IF LAST ProgStop?
SeqC CoolOn EOL
SeqC SpinOn EOL
ELSE
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
SeqC AbsOrInc EOL
SeqC Rapid StrtPos EOL
IF LAST ProgStop? OR NewToolOffset?
SeqC ToolOfst EOL
END
END
END
END {common point for all operations}
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqC FeedC ZCP3C FeedEntC EOL
ELSE
SeqC RapidC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
SeqC DrillCP EOL
GetCycle
SeqC Cycle ZDepth RLevel Dwell
IF Peck?
Peck FromCP FeedEnt
IF PeckChipBreaker?
'J*K*W' Retract 'U*'
END
ELSE
FromCP FeedEnt
END
EOL
IF CallMasterOp?
SeqC CallLabB CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqC CallLab EOL
StartSub
SeqC Rapid StrtPos EOL
ToolPath
SeqC EndSub EOL
EOR EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
SeqC Rapid StrtPos EOL
ToolPath
END
END
SetDrillEndOpZ
SeqC DrillOff EOL
IF Repeats?
FinishSubG92
END
SeqC ZCP3C EOL
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
SeqC SpinOff EOL
SeqC 'GZO' EOL
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqC Rapid FirstHome EOL
END
IF ProgStop?
SeqC 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqC EOP EOL
EOR EOL
CloseSub
Post2 {organize Subs into one program}
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'; FILE LENGTH: ' FileBytes# ' CHARACTERS' EOL
END
IF FileFeetComment?
'; FILE LENGTH: ' FileFeet# ' FEET' EOL
END
IF FileMetersComment?
'; FILE LENGTH: ' FileMeters# ' METERS' EOL
END
Close
END


Wyszukiwarka

Podobne podstrony:
Bandit IV AB [DM] MV32 89 1
Bandit IV AB M044 87
Bandit IV AB Shizouka M242 79
Sharnoa Tiger IV CO M389 89 2
Sharnoa Tiger IV [WT] MX24 89 2
Centurion IV [IS] M387 89
Bandit IV WI [BM] M459 80
AB 8400 [AQL] M609 89 2
AB 8200 [ASKO] M725 89
Bandit IIIA Shiz [DM] MV31 89 3
AB 8400 Rev F [CAS] M876 89 2
AB 8400 Rev F [EI] MW43 89 1
Stromlaufplan Passat 89 Antennenumschaltung ab 09 2001

więcej podobnych podstron