Ustawianie mostu


Installation Kit Instructions
Please read completely
before beginning.
Over the years we have gathered information from Gleason gear design
manuals, Dana Spicer instruction manuals and technical bulletins, and
General Motors repair manuals. We have personally experienced good results
using the techniques in these instructions when setting up over thirty
thousand differentials.
We highly recommend Timken bearings and have used them for as long as
we can remember. We believe Timken bearings have held up best in all of the
differentials we have assembled and disassembled. We also recommend
using only new or good used parts. New parts are usually worth installing
and save a lot of time and money that can be lost by using worn or
questionable parts that lead to early failure.
Ring & pinion gears are designed to be set-up and run with exact
tolerances. Replacing all parts every time a differential is worked on is not
only unnecessary but is ridiculous. However any gear misalignment or
deflection under load caused by worn or questionable parts can lead to early
failure that can cost a lot more than the price of replacing them the first time.
Use your best judgment and remember that fixing your differential again if it
fails will take as much time and money as it did the first time.
We hope that these instructions are helpful and you are able to get years of
use from your differential.
Thank you Robert Hunt, Jeff Wilson, and Gregg Lloyd for your expert input
and advice.
© Copyright 1993-2001/Yukon Gear & Axle
Installation Kit Instructions 1
Tool List
When working on your differential you will need a wide variety of tools. It is always
recommended that you use the right tools for the job. Using the correct tools will save
you time and help prevent parts from being damaged. Here is a list of some of the tools
that you may need:
" Dial indicator
" Genuine gear marking compound and a clean brush
" Calipers or a micrometer
" Bearing pullers
" Bearing press
" Misc. hand and air tools including:
" Three foot long breaker bar or strong impact gun
" Pinion nut socket
" Ring gear bolt socket
" Main cap bolt socket
" Six point cross pin bolt wrench
" Brake line wrench
" Pry bars for removing the carrier case
" 24 oz ball peen hammer
" 48 oz sledge hammer
" 48 oz plastic dead blow hammer
" Assorted brass punches
" Center punch or number stamp for marking main caps
" Oil drain pan
" Torque wrenches:
" foot pounds
" inch pounds
2 Installation Kit Instructions
Disassembly
1. Before I start working on anything I always make certain that I have everything I need
before I start. Check all of your new parts to be sure that you have everything you
need and make certain that you have received all of the parts that you ordered.
2. The next step is to lift the vehicle using an appropriate lift or a jack and safe jack
stands. Always make certain that the vehicle is safe to be under before starting to
work on the vehicle.
3. Then drain the oil into a suitable container. We always recycle our waste oil and hope
that you will be able to recycle yours too.
4. Next remove the axles shafts.
5. Mark both of the main caps so that you will be able to re-install them on the same side
in the same direction as they came off.
6. Keep track of the position of all of the original shims.
7. Clean and inspect all parts.
Installation Kit Instructions 3
Assembly
Order of Adjustments
When assembling or setting up a differential there are four basic adjustments. In the order
of importance they are:
1. Pinion Depth
2. Pinion Bearing Preload
3. Backlash
4. Carrier Bearing Preload
Selecting Shims
For my first assembly I usually start with the shims that were used in the differential
during the previous assembly. If the original shims from the previous assembly are not
available then I recommend using the thickness listed in the specifications information.
Preparing Parts
Before assembly I clean all parts, including the new ones, with clean solvent. I wash out
the housing with solvent and check all of the oil passages to make certain that there are
no metal particles or dirt that can lead to early wear. On many housings there are oil
passages to the pinion and grooves just outside of the carrier bearings where metal
particles hide. Be sure to check all passages and groves for metal particles and dirt!
Seal Preparation
All seal surfaces can be polished with light emery cloth or sandpaper and then wiped
with a clean rag and clean oil or solvent to remove the metal particles left after sanding.
Assembly Oil
When assembling I use a moderate coat
of gear oil on all of the bearings and
grease or oil on all of the seals and seal
surfaces. I do not use bearing grease on
any pinion or carrier bearings, only clean
gear oil.
4 Installation Kit Instructions
Pinion Trial Assembly
I have found it is easiest to assemble the pinion without a crush sleeve until the
correct pinion depth has been established. When initially installing the pinion I slowly
tighten the pinion nut until the preload is within the assembly specifications.
Initial Carrier Assembly
I have also found it works well to assemble the carrier snug but not tight during trial
assemblies so it is easier to remove and replace during the several attempts necessary to
find the shim combination for correct pinion depth and backlash.
Adjusting Backlash
After installing the pinion, the first
adjustment I make is backlash. I believe a
clear indication of pinion depth can only
be obtained when the backlash is within,
or very close to specifications. I have
found the backlash will change about
0.007 for each 0.010 that the carrier is
moved. If I want to decrease the backlash
by 0.007 I move the carrier 0.010 closer
to the pinion. If I want to increase the
backlash by 0.007 I move the ring gear
0.010 farther away from the pinion. This
is not exact for all ring & pinion sets, but
it is a good general guideline.
Checking the Pattern
After setting the backlash the next setting to check is the pinion depth. When
checking the pinion depth I use only genuine gear marking compound. Gear marking
compound gives a clear indication of gear contact without running or smearing. I
usually mix a little oil with the marking compound so that it is smooth but not runny. I
brush three or four of the ring gear teeth with a moderate coat of compound in two
different places on the ring gear. Then I rotate the ring gear past the pinion gear four or
five times to obtain a good pattern.
Important Pattern Information!
Reading the contact pattern is easy as long as I am not mislead or sidetracked. The
only part of the pattern that helps me set the pinion depth correctly is the contact
position with regards to the face and flank of the teeth. If the contact pattern appears to
be towards the heel or the toe of the ring gear teeth I pay no attention and look only at
the pattern position from face to flank. The pattern will also change from heel to toe
but in most cases an ideal heel to toe pattern can not be achieved. Trying to obtain a
Installation Kit Instructions 5
Assembly
(continued)
pattern that is centered from heel to toe will usually lead to frustration and a noisy gear
set. Even if it does not seem intuitive or reasonable, I am only concerned with the
position of the pattern from face to flank. I have found that housing alignment and the
position of the pinion bearing bore in the housing affects the pattern from heel to toe and
can not be corrected without machine work. A contact pattern that is centered from face
to flank always indicates correct pinion depth even if a pattern that is centered from heel
to toe can not be obtained.
If the contact pattern is towards the face
of the ring gear teeth then the pinion is too
far away from the ring gear. To correct the
pattern the pinion needs to be moved
towards the ring gear so that it is positioned
closer to the ring gear centerline.
If the contact pattern is towards the flank
of the ring gear teeth then the pinion is too
close to the ring gear. To correct the pattern
the pinion needs to be moved away from the
ring gear so that it is positioned farther
away from the ring gear centerline.
Ideal pattern
Used Gear Sets
When setting up a used ring & pinion I am
basically concerned with the pattern on the coast
side of the ring gear teeth and I pay very little
attention to the drive side of the gear teeth. This
is true for most used gear sets but in some cases
both the coast and drive side should be
considered.
Adjusting Pinion Depth
When changing the pinion depth I always make
large changes until the pattern is close. I
consider 0.005 to 0.015 to be a large change
and 0.002 to 0.004 to be a small change.
Changes of 0.005 to 0.008 or more will lead to
the correct pattern faster than small changes
Used drive pattern
will. I purposely make adjustments that I know
are moving the pinion too far. If I move the pinion too far and the pattern changes from
one extreme to the other then I know that the correct pattern is somewhere between
the two extremes. Once I get close to the correct pinion depth I make smaller changes
until the pattern is centered between the face and the flank of the ring gear teeth.
After the backlash and pinion depth are set I remove the carrier and set the final pinion
bearing preload.
6 Installation Kit Instructions
Setting Pinion Bearing Preload
In differentials that use a crush sleeve this is relatively easy. I always use a new crush
sleeve for final assembly. I use oil on the pinion nut washer surface during all assemblies
and red Loctite on the pinion nut threads during the final assembly. The oil on the
washer surface helps the nut turn easier while it is being tightened and the red Loctite
helps keep it tight.
Crush Sleeve Design
On a crush sleeve design differential it usually takes between three hundred (300)
and four hundred (400) foot pounds of torque to crush the crush sleeve. Over the years
I have used huge breaker bars and or very strong air operated impact wrenches to
crush the crush sleeve. I also proceed very slowly so that I get it right the first time.
The pinion preload will be zero until the bearings contact the races. When the bearings
contact the races the preload will increase very quickly. Again, I recommend taking
plenty of time to set the preload carefully so that the bearings will have a long life. If
the crush sleeve is over crushed and the pinion bearing preload exceeds the specified
allowable range the only solution that I know of is to install another new crush sleeve
and start over. After reaching the correct preload I moderately tap both ends of the
pinion to seat the bearings, races and yoke. Be careful not to hit the pinion so hard that
it damages the bearings. After  seating the pinion I check the preload again to make
certain that it is correct.
Preload Shim Design
If the differential uses shims to set the pinion bearing preload then this step may take a
few times to get it right. I usually use the original shims on the first assembly or add
0.003 to the original preload shims to make up for the bearings settling into the housing.
When first tightening the pinion nut I am careful to tighten it slowly so as not to damage
the bearing if the preload shim stack is not thick enough.
If the preload is too loose then I
remove shims so that the bearings
will be tighter against the races
and increase the preload.
If the preload is too tight then I
add shims so that the bearings will
not be as tight against the races.
I am always very careful to clean
the shims completely so that there
are no particles that may cause a
false preload reading or cause the
shim stack to change thickness
over time as the vehicle is driven.
Impact on pinion nut
Installation Kit Instructions 7
Assembly
(continued)
When making preload shim changes I like to remember where I started and which
thickness I have tried. I recommend writing down the thickness and resulting preload of
each shim combination tried.
After reaching the correct preload I moderately tap both ends of the pinion to seat the
bearings, races and yoke. Be careful not to hit the pinion so hard that it damages the
bearings. After  seating the pinion I check the preload again to make certain it is correct.
After setting the pinion depth, backlash, and pinion bearing preload I set the carrier
bearing preload. I like to set the carrier bearing preload fairly tight. There are three
different shim or adjustment methods that cover most differentials.
Final Backlash & Carrier Bearing
Preload Adjustments
Screw Adjuster Design
The first and easiest method uses screw adjusters to set the backlash and carrier
bearing preload. When setting the carrier bearing preload on this type of differential I
am careful to oil the adjuster threads on both the housing and on the adjusters
themselves. I am also careful about the order in which I tighten the adjusters so that the
backlash stays where it should even when under heavy loads.
The ring gear is always forced away from the pinion gear when ever it is transferring
power and it is never forced toward the pinion gear. When setting the backlash and
carrier bearing preload on a differential that uses screw adjusters I start with the
backlash wider than the final setting that I am adjusting it to. I always make certain the
last adjustment that I make on the left adjuster is to tighten it. If the backlash becomes
too tight I start over by opening it to a position where it is too wide again by backing off
pressure from the left adjuster and then I use the right adjuster to open up the backlash
again. At this point I tighten the left adjuster which closes down the backlash toward the
final setting. I always make certain that the last adjustment that I make on the left
adjuster is to tighten it so that there is no possibility of a space between the adjuster and
the bearing race. Any space or looseness on the left side can let the carrier move when
under load and this can cause the backlash to open up.
After the backlash approaches the final setting I tighten both the left and right
adjusters evenly so that the carrier bearing preload increases. I like to set the carrier
bearing preload as tight as I can with a ten (10) or twelve (12) inch long spanner wrench.
I have never encountered carrier bearing failure due to excessive carrier bearing preload
on a screw adjuster type differential.
If the preload is close and the backlash is too wide I tighten the left adjuster a notch or
two until the backlash is correct and the preload is tight.
If the preload is close and the backlash is too tight I tighten the right adjuster until the
backlash is correct and the preload is tight.
Like I stated before, I always make certain that the last adjustment that I make on the left
8 Installation Kit Instructions
adjuster is to tighten it so that there is no possibility of a space between the adjuster and the
bearing race.
Outside Shim Design
There are also designs that use shims between the carrier bearing races and the
housing. On these types of differentials I set the carrier bearing preload as tight as I can
without damaging the shims while driving them in. I have seldom seen carrier bearings
fail in this rearend design because of excessive carrier bearing preload. During the
original set-up of this design I set the
backlash with very little carrier bearing
preload. After I have set the backlash I add
shims to both the left and the right sides until
I obtain the correct preload.
If the preload is close and the backlash is
wide I add shims to the left side. This
increases the carrier bearing preload and
tightens the backlash at the same time.
If the preload is close and the backlash is
too tight I add shims to the right side. This
increases both the carrier bearing preload and
the backlash at the same time.
Inside Shim Design
The last design uses shims between the carrier bearing and the carrier case. On this
design I also set the preload very tight but not so tight that the carrier is difficult to install
or remove. I keep the preload very light while setting the backlash so that the carrier is
easy to remove and install. After I have set the backlash I add shims to both the left and
right sides evenly until I obtain the correct preload.
Pressing on carrier bearing
If the preload is close and the backlash is wide I add
shims to the left side. This increases the carrier bearing
preload and tightens
Carrier bearing puller
the backlash at the
same time.
If the preload is
close and the
backlash is too tight I
add shims to the right
side. This increases
the carrier bearing
preload and the
backlash at the same
time.
Final Checks
Pattern
Now that the pinion depth, pinion bearing preload, backlash, and carrier bearing
preload are set I recheck the pattern once more to be certain that everything is perfect.
Oil
When filling the differential I use high quality name brand gear oil and make certain
that I fill the unit completely.
Break-In
All new gear sets require a break-in period to prevent damage from overheating. After
driving the first 15 or 20 miles it is best to let the differential cool before proceeding. I
recommend at least 500 miles before towing. I also recommend towing for very short
distances (less than 15 miles) and letting the differential cool before continuing during
the first 45 towing miles. This may seem unnecessary but I have seen many differentials
damaged from being loaded before the gear set was broken-in. I also recommend
changing the gear oil after the first 500 miles. This will remove any metal particles or
phosphorus coating that has come from the new gear set.
ANY OVERLOADING OR OVERHEATING
WILL CAUSE THE GEAR OIL TO BREAK DOWN
AND THE RING & PINION WILL FAIL.
I hope that these instructions have been helpful and you get years of good service
from your differential
Burned ring & pinion
10 Installation Kit Instructions
Tooth Nomenclature
Terms for describing specific areas
of the gear teeth
End view of tooth from Heel
(Outer end)
Face (Top Land)
Drive
Coast
Flank (Root)
Heel
Coast
(Outer end)
(Concave)
Toe
(Inner end)
Drive
(Convex)
Installation Kit Instructions 11
Acceptable Patterns
Heel Heel
Coast Coast
(Outer end) (Outer end)
Toe Toe
(Inner end) (Inner end)
Drive Drive
Coast
Heel Heel
Coast
(Outer end) (Outer end)
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
Heel
Coast
Coast
Heel
(Outer end)
(Outer end)
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
12 Installation Kit Instructions
Pinion is Too Close
Heel Heel
(Outer end) Coast (Outer end) Coast
Toe Toe
(Inner end) (Inner end)
Drive Drive
Heel Heel
(Outer end) Coast (Outer end) Coast
Toe Toe
(Inner end) (Inner end)
Drive Drive
Heel
Heel
(Outer end) Coast
(Outer end) Coast
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
Installation Kit Instructions 13
Pinion is Too Far Away
Heel
Heel
(Outer end) Coast
(Outer end) Coast
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
Coast
Heel Heel
Coast
(Outer end)
(Outer end)
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
Heel
Coast
Heel
Coast
(Outer end)
(Outer end)
Toe
Toe
(Inner end)
(Inner end)
Drive
Drive
14 Installation Kit Instructions
SUMMARY OF INSTRUCTIONS
All sets are matched pairs. Make sure you have a matched set. Clean all parts before
you start assembly. Apply a light coat of oil to all bearings. Examine all components and
remove any burs, nicks or sharp edges that could cause components not to seat properly.
Checking Backlash
1. Set backlash to proper clearance. (See specification sheet)
2. Backlash is the free movement of the ring gear with the pinion help fixed in place.
3. Correct backlash is obtained by shimming or adjusting the
ring gear away from or closer to the pinion.
4. Pinion bearing preload should be as specified on specification
sheet. This is accomplished by a preload shim pack (of various
thicknesses) or a collapsible crush sleeve. A new crush sleeve
should always be used during final assembly.
5. Correct pinion depth is obtained by shimming the pinion in or
out, to obtain the correct tooth pattern. All housing are not
shimmed in the same location, but shimming still moves the
pinion closer to, or farther away from the ring gear. It is sug-
gested that you start with the same shim thickness on the new
gear set as was used on the old set.
OBTAINING PROPER GEAR PATTERN (Pinion Depth)
Drive Side Coast Side
" Normal or desirable pattern. The pattern should be
Heel Toe Toe Heel
centered on the tooth from face to flank. There should
usually be some clearance between the pattern and the
top of the tooth (face), and always between the pattern
and the bottom of the tooth (flank).
" Pinion is too close. Move the pinion away from the
ring gear centerline.
" Pinion is too far away. Move the pinion towards the
ring gear centerline.
PATTERN MOVEMENTS SUMMARIZED
1. Moving the ring gear closer to the pinion will decrease backlash.
2. Moving the ring gear farther away from the ring gear will increase backlash.
3. Moving the pinion closer to the ring gear will move the drive pattern deeper on the
tooth (flank contact) and slightly toward the toe. The coast pattern will move deeper
on the tooth and slightly toward the heel.
4. Moving the pinion further away from the ring gear will move the drive pattern toward
the top of the tooth (face) and slightly toward the heel. The coast pattern will move
toward the top of the tooth and toward the toe.
Installation Kit Instructions 15
Set Up Specifications
PINION BEARING PINION BEARING
DIFF PRELOAD R.G. BOLT CAP DIFF PRELOAD R.G. BOLT CAP
MODEL NEW USED B/L TORQUE TORQUE MODEL NEW USED B/L TORQUE TORQUE
(inch lbs) (0.000 ) (Foot lbs) (inch lbs) (0.000 ) (Foot lbs)
AMC DANA
Model 20 . . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . . .6-10 . . . . . . .65 . . . . . . .65 D25 . . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .50
Model 35 . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .55 D27 . . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .50
D28 . . . . . . . . . . . . . . . . . . . .10-13 . . . . . .5-6 . . . . .6-10 . . . . . . .55 . . . . . . .50
GENERAL MOTORS
D30 . . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .60
Olds/Pont D/O . . . . . . . . . . . .14-19 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .70
D44 . . . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-9 . . . . .6-10 . . . . . . .55 . . . . . . .60
 63- 79 Corvette . . . . . . . . . . .14-19 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .60
D50 . . . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-9 . . . . .6-10 . . . . . . .65 . . . . . . .60
D36 Corvette . . . . . . . . . . . . .12-15 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .55
D60, 61 & 70U . . . . . . . . . . .17-30 . . . . .8-10 . . . . .6-10 . . . . . .110 . . . . . . .80
D44 Corvette . . . . . . . . . . . . .14-19 . . . . . .6-9 . . . . .6-10 . . . . . . .55 . . . . . . .55
D70 & 70HD . . . . . . . . . . . . .20-35 . . . . .8-10 . . . . .6-10 . . . . . .110 . . . . . . .80
55P & 55T . . . . . . . . . . . . . . .14-18 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .60
D80 . . . . . . . . . . . . . . . . . . . .25-40 . . . . .9-11 . . . . .4-10 . . . . . .175 . . . . . . .90
7.2 . . . . . . . . . . . . . . . . . . . .11-14 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .60
7.5 . . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .65 . . . . . . .60 FORD
7.75 . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .65 . . . . . . .60 7.5 . . . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . .11-16 . . . . . . .60 . . . . . . .60
8.2 . . . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .60 8.0 . . . . . . . . . . . . . . . . . . . .12-14 . . . . . .6-7 . . . .10-15 . . . . . . .60 . . . . . . .60
8.2 Olds/Pont . . . . . . . . . . . .12-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .60 8.7 . . . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . .10-15 . . . . . . .60 . . . . . . .60
8.25 IFS . . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . . .6-10 . . . . . . .65 . . . . . . .55 8.8 . . . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . .11-16 . . . . . . .60 . . . . . . .60
8.5 & 8.6 . . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . . .6-10 . . . . . . .65 . . . . . . .60 9.0 OEM R&P . . . . . . . . . . . .13-15 . . . . . .6-7 . . . .10-16 . . . . . . .60 . . . . . . .60
9.25 IFS . . . . . . . . . . . . . . . .15-22 . . . . . .7-9 . . . . .6-10 . . . . . . .75 . . . . . . .80 9.0 NON OEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-10
9.5 . . . . . . . . . . . . . . . . . . . .15-22 . . . . . .7-9 . . . . .6-10 . . . . . . .75 . . . . . . .80 9.0 Daytona . . . . . . . . . . . . .14-16 . . . . . .6-8
12 Bolt Pass . . . . . . . . . . . . . .14-19 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .60 9-3/8 . . . . . . . . . . . . . . . . . .14-16 . . . . . .6-8 . . . .10-15 . . . . . . .70 . . . . . . .60
12 Bolt Truck . . . . . . . . . . . . .13-15 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .60 9-3/4 . . . . . . . . . . . . . . . . . .15-19 . . . . . .6-8 . . . .10-15 . . . . . . .75 . . . . . . .70
14T 10-1/2 . . . . . . . . . . . . . .20-35 . . . . .8-11 . . . . .6-10 . . . . . .120 . . . . . .135 10- 1/4 & 10-1/2 . . . . . . . .20-35 . . . . . .6-8 . . . .11-16 . . . . . . .95 . . . . . . .80
HO72 (10 R/G) . . . . . . . . . PRESET . . . . . . . . . . . . . .6-10 . . . . . .120 . . . . . .175
TOYOTA
CHRYSLER Passenger . . . . . . . . . . . . . . .11-13 . . . . . .5-6 . . . . . .6-9 . . . . . . .55 . . . . . . .60
7-1/4 . . . . . . . . . . . . . . . . . .12-14 . . . . . .6-7 . . . . .6-10 . . . . . . .55 . . . . . . .50 7.5 F. or R. . . . . . . . . . . . . . .12-15 . . . . . .5-6 . . . . .6-10 . . . . . . .70 . . . . . . .70
8-1/4 . . . . . . . . . . . . . . . . . .12-15 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .60 8 F. or R. . . . . . . . . . . . . . . . .12-15 . . . . . .5-6 . . . . .6-10 . . . . . . .70 . . . . . . .70
8-3/4  41 . . . . . . . . . . . . . . .13-15 . . . . . .6-8 . . . . .6-10 . . . . . . .55 . . . . . . .90 Truck V6 R. . . . . . . . . . . . . . .14-17 . . . . . .5-6 . . . . .6-10 . . . . . . .70 . . . . . . .70
8-3/4  42 . . . . . . . . . . . . . . .15-25 . . . . .7-10 . . . . .6-10 . . . . . . .55 . . . . . . .90 T100 & Tacoma . . . . . . . . . . .14-17 . . . . . .5-6 . . . . .6-10 . . . . . . .70 . . . . . . .70
8-3/4  89 . . . . . . . . . . . . . . .14-19 . . . . . .6-9 . . . . .6-10 . . . . . . .55 . . . . . . .90
9-1/4 . . . . . . . . . . . . . . . . . .14-19 . . . . . .6-9 . . . . .6-10 . . . . . . .65 . . . . . . .75
© Copyright 1993-2001/Yukon Gear & Axle
16
Installation Kit Instructions


Wyszukiwarka

Podobne podstrony:
s2u2 opis funkcji i ustawień konfiguracja programu pomoc
ustawienia
Ustawienie chelicer Costa
rozdzial 5 ustawienia dla uzytkownikow ias
Centralna mielinoza mostu u osób uzależnionych od alkoholu
ustawienie portu
Ustawianie świateł
Resetowanie ustawień wskaźnika w drukarkach HP wykorzystujące kartridże HP 21
Ustawienie punktu zerowego detalu (frezowanie)

więcej podobnych podstron