Dual Engine Multi-Effects
Processor
User s Guide
Please visit Digitech Studio on the World Wide Web at http://www.digitech.com
WARNING
FOR YOUR PROTECTION, PLEASE READ THE
CAUTION
FOLLOWING:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WATER AND MOISTURE: Appliance should not be used near water (e.g. near a
ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool, etc). Care should be taken so that objects do not fall and liquids are not spilled
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
into the enclosure through openings.
SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
POWER SOURCES: The appliance should be connected to a power supply only of
the type described in the operating instructions or as marked on the appliance.
The symbols shown above are internationally accepted symbols that warn of potential
hazards with electrical products. The lightning flash with arrowpoint in an equilateral
GROUNDING OR POLARIZATION: Precautions should be taken so that the
triangle means that there are dangerous voltages present within the unit. The
grounding or polarization means of an appliance is not defeated.
exclamation point in an equilateral triangle indicates that it is necessary for the user to
refer to the owner s manual.
POWER CORD PROTECTION: Power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying
These symbols warn that there are no user serviceable parts inside the unit. Do not
particular attention to cords at plugs, convenience receptacles, and the point where
open the unit. Do not attempt to service the unit yourself. Refer all servicing to
they exit from the appliance.
qualified personnel. Opening the chassis for any reason will void the manufacturer s
warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately
SERVICING: To reduce the risk of fire or electric shock, the user should not attempt
and take it to a dealer for service. Disconnect the unit during storms to prevent
to service the appliance beyond that described in the operating instructions. All other
damage.
servicing should be referred to qualified service personnel.
FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE
RECEPTACLE: Replace fuse with same type and rating only.
U.K. MAINS PLUG WARNING ELECTROMAGNETIC COMPATIBILITY
This unit conforms to the Product Specifications noted on the Declaration of
Conformity. Operation is subject to the following two conditions:
A moulded mains plug that has been cut off from the cord is unsafe. Discard the mains
" this device may not cause harmful interference, and
plug at a suitable disposal facility. NEVER UNDER ANY CIRCUMSTANCES
" this device must accept any interference received, including interference
SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13
that may cause undesired operation. Operation of this unit within
AMP POWER SOCKET. Do not use the mains plug without the fuse cover in
significant electromagnetic fields should be avoided.
place. Replacement fuse covers can be obtained from your local retailer. Replacement
" use only shielded interconnecting cables.
fuses are 13 amps and MUST be ASTA approved to BS1362.
LITHIUM BATTERY WARNING
SAFETY INSTRUCTIONS
CAUTION!
This product may contain a lithium battery. There is danger of explosion if the battery
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A
is incorrectly replaced. Replace only with an Eveready CR 2032 or equivalent. Make
POWER CORD.
sure the battery is installed with the correct polarity. Discard used batteries according
to manufacturer s instructions.
WARNING: THIS APPLIANCE MUST BE EARTHED.
ADVARSEL!
Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av
The cores in the mains lead are coloured in accordance with the following code:
apparatfabrikanten. Brukt batteri returneres apparatleverandłren.
ADVARSEL!
GREEN and YELLOW - Earth BLUE - Neutral BROWN - Live
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri av samme fabrikat og type. Levér det brugte batteri tilbage til leverandÅ‚ren.
As colours of the cores in the mains lead of this appliance may not correspond with
VAROITUS!
the coloured markings identifying the terminals in your plug, proceed as follows:
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laite-
valmistajan suosittelemaan tyyppin. Hävitä käytetty paristo valmistajan ohjeiden
" The core which is coloured green and yellow must be connected to the
mukaisesti.
terminal in the plug marked with the letter E, or with the earth symbol, or
VARNING!
coloured green, or green and yellow.
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent
" The core which is coloured blue must be connected to the terminal
typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikan-
marked N or coloured black.
tens instruktion.
" The core which is coloured brown must be connected to the terminal
marked L or coloured red.
This equipment may require the use of a different line cord, attachment plug, or both,
depending on the available power source at installation. If the attachment plug needs
to be changed, refer servicing to qualified service personnel who should refer to the
table below. The green/yellow wire shall be connected directly to the unit's chassis.
CONDUCTOR WIRE COLOR
L Line Brown Black
N Neutral Blue White
Earth Grnd. Green/Yel. Green
WARNING: If the ground is defeated, certain fault conditions in the unit or in the
system to which it is connected can result in full line voltage between chassis and earth
ground. Severe injury or death can then result if the chassis and earth ground are
touched simultaneously.
S-100 Section -1 Introduction
DECLARATION OF CONFORMITY
Manufacturer s Name: Digitech Studio
Manufacturer s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product Name: S-100
Product Options: All
conforms to the following Product Specifications:
Safety: EN 60065 (1993)
IEC 65 (1985) with Amendments 1, 2 & 3
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.
Digitech Studio
President of Digitech Studio
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Tel: 801.566.8800
Fax: 801.566.7005
Effective December 1, 1997
European Contact: Your Local Digitech Sales and Service Office or
International Sales Office
3 Overlook Drive #4
Amherst, New Hampshire 03031, USA
Tel: 603.672.4244
Fax: 603.672.4246
1
Section -1 Introduction S-100
Table of Contents
Safety Information
Declaration of Conformity ......................................................................................................1
Table of Contents ....................................................................................................................2
Section 1 - Introduction
Congratulations ..................................................................................................................3
Included Items....................................................................................................................3
Product Features ................................................................................................................3
Warranty..............................................................................................................................4
A Quick Tour of the S-100 ....................................................................................................5
The Front Panel ..................................................................................................................5
The Rear Panel....................................................................................................................7
Section 2 - Operation and Editing
Program Mode ..................................................................................................................8
Storing Changes..................................................................................................................8
Selecting Effect Configurations ........................................................................................8
Adjusting Dry Path Global Mix ..........................................................................................9
MIDI Channel Selection and CC Information ..................................................................10
EQ and Noise Gate Adjustments ........................................................................................10
Editing Engine A and B Engines ........................................................................................12
Section 3 - Effects and Parameters
Modulation Effects..............................................................................................................13
Pitch Shifters ......................................................................................................................14
Delay ..................................................................................................................................14
Reverb ................................................................................................................................16
Other Effects (Vocoder, Ring Modulator and Compressor) ..............................................17
Section 4 - Appendix
Resetting the S-100 ............................................................................................................18
Specifications ......................................................................................................................19
Program List........................................................................................................................20
2
User Guide
S-100 Section -1 Introduction
Section-1 Introduction
Congratulations...
... you are now the proud owner of a Digitech Studio S-100 Multi-Processor. The S-100 offers you Dual-Engine processing
with five different effect configurations and a full palette of studio-quality effects. In addition, the S-100 has an easy-to-use
interface that makes the S-100 an absolute necessity for use in studio or live applications.
This owner's manual is your key to understanding the powerful world of the S-100. Read it carefully. After you've had time
to familiarize yourself with the unit, try experimenting with unusual effect combinations. You are certain to achieve sounds
never thought possible before. Good luck, and thank you for choosing a Digitech Studio product.
Your S-100 was carefully assembled and packaged at the factory. Before you proceed any further, make sure the following
items are included:
" (1) Owner s Manual
" (1) Digitech S-100 Multi-effects Processor
" (1) Power Supply
" (1) Digitech Studio warranty card
Please save all packing materials. They were designed to protect the unit from damage during shipping. In the unlikely event
that the unit requires service, use only the factory supplied carton to return the unit.
S-100 Features:
" Dual-Engine processing power " 5 Effect configurations
" Stereo Inputs and Outputs " Full bandwidth effects (20-20kHz)
" 20-bit A/D and D/A conversion " MIDI program changes
" Footswitch compatible " 96 dB signal-to-noise ratio
" Easy-to-use interface " 99 User Programs
" Studio Quality Reverbs " Vocoder and Ring Modulator Effects
3
User Guide
Section -1 Introduction S-100
We at Digitech Studio are very proud of our products and back-up each one we sell with the following warranty:
1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty.
2. Digitech Studio warrants this product, when used solely within the U.S., to be free from defects in materials and
workmanship under normal use and service.
3. Digitech Studio liability under this warranty is limited to repairing or replacing defective materials that show evidence of
defect, provided the product is returned to Digitech Studio WITH RETURN AUTHORIZATION, where all parts and labor
will be covered up to a period of one year. A Return Authorization number may be obtained from Digitech Studio by
telephone. The company shall not be liable for any consequential damage as a result of the product's use in any circuit or
assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. Digitech Studio reserves the right to make changes in design, or make additions to, or improvements upon this product
without incurring any obligation to install the same on products previously manufactured.
6. The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone
other than a certified Digitech Studio technician or, if the product is used with AC voltages outside of the range suggested
by the
manufacturer.
7. The foregoing is in lieu of all other warranties, expressed or implied, and Digitech Studio neither assumes nor authorizes
any person to assume any obligation or liability in connection with the sale of this product. In no event shall Digitech
Studio or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty
due to causes beyond their control.
Digitech Studio"! and S-100 are registered trademarks of the Harman Music Group Incorporated.
NOTE: The information contained in this manual is subject to change at any time without notification. Some information
contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this
version of the manual was completed. The information contained in this version of the owner's manual supersedes all
previous versions.
4
User Guide
S-100 Section -1 Introduction
A Quick Tour of the S-100
The Front Panel
1 2 3 4
C1 C2 C3 L R
Mod/Pitch Mod/Pitch
C4 C5 Delay Delay
Reverb Reverb
Other Other 23
Predelay Decay Size Level
5 6 7 8 9 a~g 10
1) Configuration Matrix - This matrix shows the five different effect configurations available in the S-100.
2) Input Meter/ Effect Display - In Program mode, this meter displays the input signal entering the unit. In Edit mode, it
will indicate which effect is being used.
3) Number Display - In Program mode, this number display will indicate program number (decimal point indicates a user
program). In Edit mode, the display will indicate effects and parameter values.
4) Program/Data Wheel - In Program mode, this wheel is used to change programs and when the unit is in Edit mode it is
used to select effects and change parameter.
5) Program Button -This button returns the S-100 to program mode when pressed.
6) Store Button - This button is used to store program modifications in the S-100.
7) Configuration Button - This button is used to select Configuration mode. Once pressed, use the
wheel to select a different effect configuration for the selected program.
8) Mix/MIDI - This button is used to turn the Dry signal path On and Off and select the MIDI channel that program change
information is received on.
9 a~g) Program Editing buttons - These seven buttons are used to make key editing modifications to the S-100 and their
functions are as follows:
9-a) EQ/Gate - This button (in conjunction with the four parameter buttons) are used to adjust the three band EQ and
Noise gate threshold and release. Press once to select the EQ and press twice to select the noise gate.
9-b) Engine A - This button selects the Engine A effect module. Once this button is pressed, use the
5
User Guide
Section -1 Introduction S-100
wheel to change the effect used in this module.
9-c) Engine B - This button selects the Engine B effect module. Once this button has been pressed, use the
wheel to change the effect used in the module.
9-d) Parameter 1 / Predelay - This button selects parameter 1 for editing in conjunction with the
wheel. It is also the Predelay parameter of the Reverb effect.
9-e) Parameter 2 / Decay - This button selects parameter 2 for editing in conjunction with the
wheel. It is also the Decay parameter of the Reverb effect.
9-f) Parameter 3 / Damping - This button selects parameter 3 for editing in conjunction with the
wheel. It is also the Damping parameter of the Reverb effect.
9-g) Parameter 4 / Level - This selects parameter 4 (level) for editing in conjunction with the wheel.
10) Bypass - This button is used to Bypass all of the digital effects in the S-100 and allow the original dry signal to pass
through the S-100.
6
User Guide
S-100 Section -1 Introduction
The Rear Panel
1 2 3 4 5 6 7 8
INPUT LEVEL LEFT/MONO RIGHT IN LEFT/MONO RIGHT OUT POWER SUPPLY FOOTSWITCH MIDI IN
IN OUT
1) Input Level- This knob controls the level of signal entering the S-100. For optimal performance, set this level so the
Input level indicators (located on the front panel) occasionally light the red LEDs.
2) Left/Mono Input - This Input jack is used for the Left or Mono input. When only the Left input jack is used, the signal is
sent to both Left and Right S-100 inputs.
3) Right Input - This is the Right Input jack for the S-100 that when used with Left input will preserve stereo imaging.
4) Left/Mono Output - This is the S-100 s left audio output. This output must be used if a mono effect
is desired.
5) Right Output - This is the S-100 s right audio output. Use both left and right outputs to take
advantage of stereo effects.
6) AC Line Input - This is the AC adapter receptacle. Use only the included PS 750 power supply.
7) Footswitch Jack - This jack is used for the insertion of the Digitech FS-300 footswitch that will control program changes
and Bypass the digital effects of the S-100.
8) MIDI IN - This MIDI jack is used for receiving MIDI program change and CC information.
7
User Guide
Section -2 Operation and Editing S-100
Section-2 Operation and Editing
This section will provide you with all of the information necessary to get the most out of your S-100.
Program Mode
When the S-100 is in program mode, you can move from one program to the next by either using the
wheel, the optional Digitech FS-300 footswitch or incoming MIDI program change commands from another device such as a
sequencer or keyboard.
When the S-100 is in edit mode and you wish to abort and return to program mode, simply press the button.
Storing Changes
When a program has been modified, the program number will blink in the number display when the unit is in program
mode. To store changes, press the button once. The display alternates between st and the user program
location to be stored to. This simply means that S-100 is now giving you the option to store this modified version of the
program as a user program at any number from 1 to 99. At this point, you may use the wheel to change
the storing position to another program number. When the target preset location (shown in the display) is correct, press the
button once again. The display will momentarily read: --
indicating that the modified program is being stored.
Selecting Effect Configurations
The S-100 provides you with five different effect configurations that allow you ultimate flexibility and versatility in effect
routing. The five configurations appear on the front panel as follows:
C1 C2 C3
C5
C4
Effect Module Size
Effect Configuration 1 uses one effect module because both processing engines are combined for maximum processing
power. This larger module allows you to have longer delay times and more dense sounding reverbs. Effect configurations
2-5 use Half size effect modules which allow you to use two effects per program
8
User Guide
S-100 Section -2 Operation and Editing
To select any one of these five different configurations, simply perform the following procedure:
" Press the button and the display will briefly read: CFindicating that you are in the configuration select
mode and now the display will appear something like this:
C1
" Now turn the wheel until the desired configuration appears (C1-5) in the display.
" To exit the Effect configuration menu, simply press the button where the display will flash the program
number until the program change is stored or until you change to the next program.
Adjusting the Dry Path Global Mix
This editing procedure will allow you to globally turn a Dry signal path Off for use with a mixing consoles' effects sends or
On for use with single instrument input signals (such as guitar, saxophone and others). The procedure is as follows:
" To edit the Dry signal within the effect configuration of the S-100 (turning it On or Off), press the button
once and the display will briefly read: drindicating the dry path mix and then On, indicating that the Dry signal is on.
If you wish to turn the dry path off, simply turn the wheel counter clockwise and the display will
now read:
Of
" This now indicates that the Dry signal has been turned Off creating a 100% Wet signal globally in the S-100. To exit this
mode, press the button.
Note: The Dry path will automatically be turned off when either a Tremolo, Panner, Vocoder, Compressor, Rotary
Speaker or Reverse Reverb effect is used in a program, since the dry signal is already included in these
effects.
9
User Guide
Section -2 Operation and Editing S-100
Selecting the MIDI Channel and MIDI CC Information
" To select the MIDI channel in which the S-100 receives program change information, from Program mode, press the
button twice and the display will briefly read: ch (this indicates MIDI channel mode), followed by:
1
" Now turn the wheel to select the desired MIDI channel. The options for the MIDI channel selection
ranges from: 1-16, Alland of (Off).
MIDI program change numbers will be as follows:
1-99 = Programs
100 = Effects Bypass
101 = Exit Effects Bypass
102 = Effect Bypass Toggle
103 = Selects User Program Bank
104 = Selects Factory Program Bank
" To exit the MIDI channel menu, press the button.
MIDI CC Information
The S-100 will also receive MIDI CC information for parameter control of the following parameter:
Dry Level - is turned On or Off by MIDI CC number - CC 7.
EQ and Noise Gate Adjustments
This editing function allows you to make key EQ and Noise gate modifications to custom tailor your sound for each program.
The procedure for both is as follows:
Adjusting the EQ
The S-100 offers a three band EQ with Lo EQ, Parametric Frequency, Parametric Level and Hi EQ parameters. To adjust
any one of these four, perform the following procedure:
10
User Guide
S-100 Section -2 Operation and Editing
" Press the button once and the display will briefly read:
e
" Now to make adjustments to the four different EQ parameters use the buttons. Parameter and value
range for each is listed below.
Parameter 1 -LoEQ - Range for the Low EQ is from -12 to +12 dB.
Parameter 2 - Parametric Frequency - Range for the Parametric Frequency is from 1 to 26.
Parameter 3 - Parametric Level - Range for the Parametric Level is from -12 to +12 dB.
Parameter 4 - Hi EQ - Range for the High EQ is from -12 to +12 dB.
" To modify any one these four parameters, simply press the respective button and then turn the
wheel.
" Once the modifications are done, remember to store any changes and press the button to return to
Program mode.
Adjusting the Noise Gate
The S-100 gives you the ability custom tailor the Noise gate parameters (Threshold and Release) for each program by
performing the following procedure:
" Press the button twice. The display will appear something like this, indicating that you are in Noise Gate
edit mode:
ng
" Now press the button and thwill appear prompting you to adjust the Noise gate Threshold by
turning the wheel. The range for the Noise gate Threshold is from Off, 99 to 0.
" To adjust the Noise Gate Release , press the and the display will read: rE, prompting you to use the
wheel to adjust the Noise Gate Release parameter. Release range is from 1 to 10.
" Once all Noise gate modifications have been made, remember to store the changes and press the button to
return to program mode.
11
User Guide
Section -2 Operation and Editing S-100
Editing Engine A and B Modules
Because of its processing power, the S-100 gives you two Engine modules that are fully programmable. The following section
explains the simple procedure for Engine A and B editing.
Selecting and Editing Effects
" From Program mode, press either the or button. The current type of effect will light the
corresponding LED in the effect display and it s two letter abbreviation will appear in the number display looking
something like this:
L R
Mod/Pitch Mod/Pitch
Delay Delay
Reverb Reverb
rs
Other Other
Note- In order to edit Engine B, configurations 2-5 must be used.
" Now turn the wheel to select the effect to be used. The effect display s LED and number display s
abbreviation will change as the new effects are selected.
" Once the effect to be used has been selected, you can use the edit buttons to modify the parameters
of the selected effect.
For a complete list of the effects available and their respective names, please see Section 3 on pages 13-16.
" Once all of the edits have been made to the selected program, make sure to store any changes and then press the
button to return to the Program mode.
12
User Guide
S-100 Section -3 Effects and Parameters
Section - 3 Effects and Parameters
This section provides you with a detailed description of the Digital effects in the S-100 and their parameters and values. A
complete list of these effects is also printed on the top of the S-100.
Modulation Effects
Effect Name Parameter 1 Parameter 2 Parameter 3 Parameter 4
Chorus - CH Speed - SP Depth - de Delay - dL Level - L
Flange - FL Speed - SP Depth - de Feedback - Fb Level - L
Phaser - PH Speed - SP Depth - de Feedback - Fb Level - L
Tremolo - tr Speed - SP Depth - de N/A Level - L
Panner - Pn Speed - Sp Depth - de N/A Level - L
Rotary Speaker - RS Speed - SP Type - Ty X-over Freq - CF
Level - L
The Modulation effects menu offers a vast list of modulating effects ranging from Chorus to a Rotary Speaker simulator.
These modulation effects are ideal producing lush sounding effects that can add dimension to any signal. The parameters
and values for the modulation effects are as follows:
Speed The Speed parameter controls the speed of the modulation in the effect.
Range is from 0 to 99 or Slow to Fast.
Depth This parameter controls the amount of depth of the modulation effect.
Range is from 0 to 40.
Delay This parameter controls the delay time within the modulation effect.
Range is from 0 to 40 milliseconds.
Feedback This parameter controls the amount of regeneration feedback in the
modulation effect. Range is from 0 to 97%.
Type This parameter selects between six different modulation extremes.
Cross-over Frequency This parameter selects the frequency where the signal is split between
the Rotor and the Horn. Settings are 1 - 4
Level This parameter allows you to set the overall level of the selected effect.
Range is from 0 to 99.
13
User Guide
S-100
Section -3 Effects and Parameters
Pitch Shifters
Effect Name Parameter 1 Parameter 2 Parameter 3 Parameter 4
Pitch Shift - PS Shift - Sh Tracking - tr N/A Level - L
Detuner - dn Detune Amt - dA N/A N/A Level - L
The Pitch Shifting effects menu includes a Pitch Shifting effect that allows you to shift the original signal to help produce
Harmony effects, while the Detuner effect will help you thicken up any signal to add dimension to your sound. Parameters
for the Pitch Shifting Effects are as follows:
Shift This parameter sets how far the signal is shifted. Range is from -12 to
+24 semi-tones.
Tracking This lets you select the tracking level of the Pitch shifter effects. Range is
from 1 to 3.
Detune Amount This parameter sets the amount of Detune in the effect. Range is from -
12 to +12 cents.
Level This parameter allows you to set the overall level of the selected effect.
Range is from 0 to 99.
Delay
Effect Name Parameter 1 Parameter 2 Parameter 3 Parameter 4
Mono Delay - d1 Delay Coarse -dC Delay Fine - df Feedback - FB Level - L
Delay Coarse -dC
Stereo Delay - d2 Delay Fine - df Feedback - Fb Level - L
Delay Coarse -dC
Ping Pong - d3 Delay Fine - df
Feedback - Fb Level - L
Karaoke - d4 Delay Time - dt N/A Repeats - rP Level - L
The S-100 offers three different Delay effects including: Mono, Stereo and Ping Pong, offering ultimate flexibility in digital
delay applications. The S-100 also offers a Karaoke delay effect. The parameters and their values are as follows:
Note: When Delay effects are used in Effect Configuration 1 (which is a Whole effect module), longer delay times
are available. These Delay time differences are marked W (Whole) and H(Half) in the Maximum delay time
chart on the following page.
14
User Guide
S-100 Section -3 Effects and Parameters
Maximum Delay times
D-1 (Half=1000 milliseconds and Whole=2000 milliseconds)
D-2 (Half=700 milliseconds and Whole=1000 milliseconds)
D-3 (Half=1000 milliseconds and Whole=2000 milliseconds)
Delay Coarse This parameter controls the length of the Delay Coarse time Range is
from .
1(which equals 100 milliseconds) to 2. 0 (which equals 2
seconds).
Delay Fine This parameter controls the length of the Delay Fine time. Range is from
0 to 99 milliseconds.
Delay Time This parameter controls the length of the Delay Time that is offered in
the Karaoke. Delay Time settings are 1-5.
Feedback This parameter controls the amount of delay repeats in the delay effect.
Range is from 0 to 99% and repeat-hold (rh).
Repeat This parameter controls the amount of delay repeats in the D-4 Karaoke
effect. Range is from 1 to 10.
Level This parameter allows you to set the overall level of the selected effect.
Range is from 0 to 99.
15
User Guide
Section -3 Effects and Parameters S-100
Reverb
Effect Name Parameter 1 Parameter 2 Parameter 3 Parameter 4
Stage - St Predelay - Pd Decay - dC Damping - Da Level - L
Predelay - Pd Decay - dC Damping - Da Level - L
Room - ro
Predelay - Pd Decay - dC Damping - DA Level - L
Hall - HA
Predelay - Pd Decay - dC Damping - da Level - L
Plate - PL
Chamber - Ch Predelay - Pd Decay - dC Damping - da Level - L
Predelay - Pd Decay - dC Damping - da Level - L
Cathedral - Ca
Decay - dC Damping - dA Level - L
Predelay - Pd
Arena - Ar
Predelay - Pd Decay - dC Diffusion - di Level - L
Gated - Ga
Diffusion - di
Reverse - rE Predelay - Pd Decay - dC Level - L
Reverb is the perfect effect for adding dimension to any recording or live application where you need to emulate the size and
shapes of different types of rooms. The following explains the parameters that are available in the Reverb effects.
Note: When Reverb effects are used in Effect Configuration 1 (which is a Whole effect module) larger and more
dense sounding Reverbs can be attained.
Pre Delay This parameter controls the length of time before the reverb reflections
are heard. Range is from 0 to 99 ms.
Decay This parameter controls the decay length (reverb time) of the reverbera-
tion. Range is from 1 to 10.
Damping This parameter controls the high frequency decay of the reverb effect
and ranges from 1 to 10.
Diffusion This parameter controls the reverb smoothness and ranges from 1 to 10.
Level This parameter allows you to set the overall level of the selected effect.
Range is from 0 to 99.
16
User Guide
S-100 Section - 3 Effects and Parameters
Other Effects
Effect Name Parameter 1 Parameter 2 Parameter 3 Parameter 4
Ring Modulator- Rg Frequency - Fr N/A N/A Level - L
Compressor - Co Threshold - Th Ratio - Rt Attack - At Gain - gA
Vocoder - Cd Sibliance - si Type - Tp N/A Level - L
The S-100 also offers an additional menu of hard to find effects including: a Vocoder effect which takes a vocal signal (using
the Left input) and superimposes it onto another input signal such as a keyboard (using the Right input) to produce a vocal
effect that sounds more robotic than human. This menu also provides you with a Ring modulator that can produce mathe-
matically-based harmonic effects. And last but not least, we have also included a state-of-the-art Compressor that is ideal for
making any signal stand out with the right amount of compression. The parameters for these effects are as follows:
Frequency This parameter sets the modulation frequency of the Ring Modulator
effect. Range is from 1 to 99.
Threshold This parameter sets threshold level of the compressor. Range is 60 to 0.
Ratio This parameter sets the compressor ratio. Range is from 1 to 19
and ".
Attack This parameter controls the attack time of the compressor. Range is
from 1 to 10.
Gain This parameter allows you to set the overall gain of the selected effect.
Range is from -19 to 20.
Type This parameter allows you to select the different types of Vocoder effect
setting in the S-100. Types include: 1-5.
Sibilance This parameter allows you to set the amount of Essing that is passed
through the Vocoder effect. Range is from 0 to 99.
Level This parameter allows you to set the overall level of the selected effect.
Range is from 0 to 100.
17
User Guide
Section - 4 Appendix S-100
Section - 4 Appendix
This section provides you with information to Factory Reset the S-100, a Specification page and a Program list
Resetting the S-100
This procedure will allow you to perform a complete factory reset on the S-100.
Warning- All previous program information will be deleted when the reset is performed
" To perform a factory reset on the S-100, simply press and hold the button while applying power to the
unit and the display will briefly read: -- and then appear like this:
Fr
" Now release the button and immediately press the button and the S-100 will proceed to reset.
In the process of resetting, the S-100 will briefly display the current software version number and then return to
program mode.
18
User Guide
S-100 Section - 4 Appendix
Specifications
Frequency Response: 20-20kHz +/-0.5dB
Signal-to-Noise Ratio: 96dB (A-Weighted ref=Max signal 22kHz measurement bandwidth)
THD: Less than 0.008%
Memory Allocations: 99 User - 99 Factory Programs
Sampling Rate: 46.875kHz
A/D Converter: 20 bit, 128 oversampled
D/A Converter: 20 bit, 128 oversampled
External Signal Path Width: 24 bits
Internal Signal Path Width: 24 bits
Multiplier Size: 24 bits x 24 bits
Inputs: Stereo (2) 1/4 Unbalanced - Max In + 18 dBu
Outputs: Stereo (2) 1/4 Impedance Balanced - Max + 18 dBu
MIDI: MIDI In Program Changes
Power Consumption: 5 watts
Power Requirements: Included external power supply (PS 750)
Net Weight: 4.2lbs (1.91kg)
19
User Guide
Section -4 Appendix S-100
Program List
The following is a list of all the factory Programs in the S-100
Showcase
50 Deep Slow Tremolo
1 Stereo Large Hall
51 Fast Shallow Tremolo
2 Deep Phaser and Delay
52 Wide Mid-Speed Panner
3 Deep Chorus and Reverb Parallel
53 Slow Wide PAnner
4 Gold Foil Plate
54 Leslie Slow to Fast
5 Octave Down Pitch & Parallel Detune
55 5th Up Pitch Shift
6 4 Voice Chorus
56 4th Down Pitch Shift
7 Stereo Karaoke Delay
57 Octave Down Pitch Shift
8 Panning Detune
58 Octave Up Pitch Shift
9 Deep Space
59 Mild Detune
60 Heavy Detune
Reverbs
61 Vocoder 1
10 Bright Mid-Size Hall
62 Vocoder 2
11 Stereo Dark Hall
63 Compressor
12 Extra Thick Hall
64 Ring Modulator
13 Large Empty Arena
14 Sold Out Arena
Multi-Effects
15 Forever In Reverb
65 Medium Chorus and Arena Reverb
16 High Vaulted Cathedral
66 Shallow Chorus with Delay
17 Vocal Cathedral
67 Deep Chorus Hall
18 Small Bright Room
68 Bright Panning Chorus
19 Split Vocal Room
69 Panning Shimmery Chorus
20 Wood Recording Studio
70 Warm Flanger and Hall Reverb
21 Thick Studio with Slow Modulation
71 Deep Flange and 1 Second Echo
22 Sparse Vocal Chamber
72 Shallow Phaser and Plate
23 Warm Chamber
73 Deep Phase and Pong Delay
24 Percussion Plate
74 Tremolo and Chamber
25 Industrial Plate
75 Tremolo and Echo
26 100ms Gated Reverb
76 Panner and Cathedral
27 300ms Gated Reverb
77 Panning Arena
28 600ms Gated Reverb
78 Panning Delay
29 Stereo Reverse Reverb 400ms
79 Pitch 5th Up and Plate Reverb
80 Pitch Octave Down and Ping Pong Delay
Delays
81 Detune and Room Reverb
30 Stereo Doubling Delay
82 Deep Detune and Echo
31 Stereo Slapback Delay
83 1/2 Sec Delay and Hall Reverb
32 Stereo Slap Right/Left Delay
84 Delay and Plate Reverb
33 Stereo 300ms Echo
85 Delayed Reverb
34 Stereo 400ms 30% Feedback
86 Compressed Hall Reverb
35 2 Second 2 Tap Delay
87 Compressed Delay
36 Stereo 500ms 25% Feedback Delay
88 Compressed Chorus
37 Stereo 800ms 20% Feedback Delay
89 Ping Pong Gated Reverb
38 Ping-Pong 1500ms 20% Feedback Delay
39 Mono 2 Second Delay Loop
Split Effects
90 Chorus Left - Reverb Right Summed
Modulation
91 Phaser Left - Pitch Right Split
40 Medium Chorus
92 Delay Left - Gated Reverb Right Summed
41 Deep Chorus
93 2 Tap Room Delay
42 4 Voice Medium Chorus
94 Short Plate Left - Hall Right Summed
43 Deep Depth Chorus
95 Panner Left - Compressor Right Summed
44 Shimmery Chorus
96 Reverse Reverb Left - Ring Modulator Right Split
45 Flange Hi Sweep 40%
97 Slap Delay Left - Room Reverb Right Split
46 Flange Hi Sweep 70%
98 Octave Up Left - Octave Down Right Summed
47 Slow Shallow Phaser
99 Fast Phase Left - Arena Reverb Right Split
48 Medium Phaser
49 Deep Phaser
20
User Guide
S-100
21
User Guide
8760 South Sandy Parkway
Sandy, Utah, 84070
Telephone 801.566.8800
FAX 801.566.7005
International Distribution:
3 Overlook Drive, Unit 4
Amherst, New Hampshire 03031 U.S.A.
FAX 603.672.4246
Digitech Studio"!, S-100 are registered trademarks
of the Harman Music Group Incorporated
Copyright © 1997
the Harman Music Group Incorporated
Printed In U.S.A. 4/98
Manufactured in the U.S.A.
S-100 18-2208-B
Please Visit Digitech Studio on the World Wide Web at:
http/digitech.com


Wyszukiwarka

Podobne podstrony:
100 sposobow na Visual Studio0vis
8 37 Skrypty w Visual Studio (2)
VA US Top 40 Singles Chart 2015 10 10 Debuts Top 100
100 0013
Pinnacle Studio 11 plus tworzenie keygena
100 0001
20 Phys Rev Lett 100 016602 2008
plan studiow

więcej podobnych podstron