{Change Comments ***********************************************************}
{1/10/94
Copied & odified: Fan 10M MS MVJr[¨] M050.81.2
For: Sunrise West
Machine: Comet 1250 VMC Machining Center
Control: Mitsubishi 330M
Versions: ncCad 4.32/ncCam 4.32/ncPost 4.32.01/Compost4.21.19
Changes made per conversation with Rike Miller at Sunrise West and sample program.
Added G43 to Tool Length Offset Enable in Composts Commands 5 Dialog.
Cosmetic changes to FirstOperation, NewTool and end of Prog.
Changed literal 'G30Y0.' to 'G30Z0.' at NewTool and end of Prog.
Customer says G30Y0. is normal for Horizontal machine, but his is a Verticle machine.
Deleted support of CutterRadiusCompensation.
Requested because customer uses Virtual and does not allow him to turn it off.
Deleted CRCOffC at FinishSub1 sub, RapidFeat and LineFeat at ToolPath, NewTool and end of
IF Milling.
Deleted CkCRC sub and call to same at StdLine.
Deleted CRCOffsetC at StdLine.
Deleted ResetCRCNum at ToolPath.
Changed to FIRST TOOL NOT IN SPINDLE at FirstOperation.
Deleted PreTool at FirstOperation and NewTool.
Deleted ToolChng handling of ToolOver(1) situation at end of Prog.
DWB}
{3/15/96, Updated to .84 version, MPK}
{3/22/96, Tested ZOnlyRepAutCycle, Incremented number to .87, MPK}
{8/6/96
Updated: Mit 330M Comet [SRW] M620.87
Created: Mit 330M Comet [SRW] M620.89
For: Gibbs & Associates/Riedel Machine Company
Machine:
Control:
Versions: Catalyst v3.05.03C/Compost 4.21.37/v1.0b1
Updated for Catalyst v3.05C per Fanuc 6M M001.89 Format
DWB}
{8/8/96
Copied: Mit 330M Comet [SRW] M620.89
Created: Mit 520AM Comet [RM] MZ18.89
For: Riedel Machine Company
Machine: Comet VMC500
Control: Mitsubishi Meldas 520AM
Versions: Catalyst v3.05.03C/Compost 4.21.37/v1.0b1
Changes made per Richard Riedel.
Added FORMAT#7, '#' at Prog Numeric Format Definitions.
Added DIV# to FORMAT#5 at Prog Numeric Format Definitions.
Added RapidF# to FORMAT#7 at Prog Numeric Format Definitions.
Added support of CutterRadiusCompensation at normal places.
Added condition to output Feed ZCP3 'F50.' RapidF# to CRCOff at FinishSub1 and IF Milling.
Deleted Flag(2) at ckCRC and ckCRCNum subs and at setup and initializations.
Moved CRCOffsetC from ckCRCNum sub to ckCRC sub.
Deleted contents of ckCRCNum sub and calls to same.
Modified startup code for FirstOperation, NewTool and SameTool.
Modified OfstOff block at NewTool, SameTool and end of Prog.
Added ckSpeed sub.
Suppresses Speed SpinOn for RigidTap Cycle.
Changed to FIRST TOOL IN SPINDLE at FirstOperation.
Added special codes for RigidTap Cycle support at IF Drilling.
Added UnTool ToolChng at end of Prog.
DWB}
{4/1/97,
Initial: Mit 520AM Comet [RM] MZ18.89
Created: Mit Meldas 500M [ETS] MY56.89
For: ETS
put OpToolID and ToolChng on separate lines, deleted untool at program end, MPK}
{4/19/97,
Initial: Mit Meldas 500M [ETS] MY56.89
Created: Mit Meld 500M [ETS] MY56.89.1
made longhand processor, MPK}
{Prog Numeric Format Definitions ****}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ClearancePlane3#,4)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(TrackZNO#,4)
FORMAT(DIV#,5)
FORMAT(CallMasterNum#,5)
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(RapidF#,7)
{Prog Subroutines ****}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' Tag# ' )' EOL
END
RETURN
DoCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN
BadMPWFOReport:
SetStatusOff
' ' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
'Ä„ NOTE: Even though you have elected to Ä„' EOL
'Ä„ process this file using Multiple Ä„' EOL
'Ä„ Parts with Work Fixtures, there exist Ä„' EOL
'Ä„ non-zero values in the invisible, Ä„' EOL
'Ä„ Equally SpacedÉ fields, as follows: Ä„' EOL
'Ä„ Ä„' EOL
'*****************************************' EOL
IF NotEqual? PartShiftX# Num#('0')
' X axis shift = ' PartShiftX# EOL
END
IF NotEqual? PartShiftY# Num#('0')
' Y axis shift = ' PartShiftY# EOL
END
IF NotEqual? PartShiftZ# Num#('0')
' Z axis shift = ' PartShiftZ# EOL
END
'*****************************************' EOL
'Ä„ Ä„' EOL
'Ä„ Please reset these values to zero as Ä„' EOL
'Ä„ they affect the coordinate values Ä„' EOL
'Ä„ output, starting with Part# 2. Ä„' EOL
'Ä„ Thank You. Ä„' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
' ' EOL
SetStatusOn
RETURN
PSInit:
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN
PSStuff:
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF
END
RETURN
DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN
ExitMove:
SeqC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN
ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN
CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJ
ELSE
ArcR
END
RETURN
ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC CRCOffsetC
END
END
RETURN
FormatLine:
ckCRC FeedC MoveXYZC
RETURN
ckCRCNum:
{ Not Needed }
RETURN
ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat? { Drilling Only }
SeqC MoveSXYZC EOL
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC RapidC MoveXYZC EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatLine FeedRateC EOL
DecelMove2
END
SeqC FormatLine DecelFeed EOL
ELSE
SeqC FormatLine FeedRateC EOL
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN
AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
IF Repeats? AND ZShiftOnly?
EntryMove
END
SeqC IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN
Milling:
EntryMove
ToolPath
RETURN
XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
CRCOffC
IF FeedConnect?
IF SPXMove? OR SPYMove?
SeqC FeedC MoveSXYC FeedEntC EOL
END
IF ZShiftOnly?
EntryMove
END
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
IF FeedEntry?
SeqC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN
NoRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN
XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN
ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
EachRep
IF NOT FirstCycle?
IF FeedConnect?
SeqC AbsOrInc EOL
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
ELSE
AbsOrInc
ExitMove
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
IF FeedEntry? AND NOT FIFO?
SeqC ZCP2 EOL
END
END
EntryMove
SeqC IncValue EOL
END
EntryMove
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN
DrillStuff:
SeqC DrillCP EOL
GetCycle
IF Tap? AND NOT CWSpindle?
'G74'
ELSE
Cycle
END
SeqC FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF RigidTap?
'E' DIV# Num#('1') FeedTapIPR#('1') Speed ',R1'
ELSE
FeedEnt
END
EOL
TrackZNO# FIRST SPZ#
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
ProgStart:
InitProg
TagInit
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000')
SetMaxFeed('500')
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
OpGuts:
RapidF# { No Output }
IF Milling?
SeqC ZCP2C EOL
IF AutoCycle?
IF Repeats?
IF ZShiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
DoCycleComment
IF FirstCycle?
DrillStuff
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
SetDrillEndOpZ
SeqC Rapid 'G80' ZCP3 EOL
END
END
RETURN
WFOStuff:
IF MultipleParts? AND WorkFixtureOffsets? AND NewWFO?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS AND WORK FIXTURE OFFSETS' EOL
ELSE
IF NewWFO?
'G' NewWFO#
ELSE
IF MultipleParts? AND WorkFixtureOffsets? AND NOT SameTool?
FORMAT(ADD#,5)
'G' ADD# NewWFO# SUB# Tag# Num#('1')
FORMAT(ADD#,4)
ELSE
IF NeedWFO1? AND NOT SameTool?
'G' NewWFO#
END
END
END
END
RETURN
ResetWFO:
IF WorkFixtureOffsets?
SeqC WFO1 EOL
END
RETURN
CkSpeed:
GetCycle
IF Drilling? AND RigidTap?
ELSE
IF FirstOperation? OR NewTool?
Speed SpinOn
ELSE { SameTool }
IF LAST ProgStop?
SpeedC SpinOn
ELSE
SpeedC
END
END
END
RETURN
InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
RETURN
FirstOp1:
DoPartCycleComment
DoOpComments
DoPostScript
Seq Rapid Plane AbsOrInc 'G80G49' CRCOff 'G28Z0' EOL
SeqC OpToolID EOL
SeqC ToolChng EOL
CheckPass
RETURN
FirstOp2:
SeqC WFOStuff StrtPos CkSpeed EOL
RETURN
FirstOp3:
SeqC OfstOn CoolOn EOL
RETURN
NewToolOp1:
SeqC CoolOff EOL
SeqC Rapid AbsOrInc 'G49' CRCOff 'G28Z0M19' EOL { OfstOff }
RETURN
NewToolOp2:
DoEndOpPS
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN
NewToolOp3: {Start new Operation}
Seq Rapid PlaneC AbsOrInc 'G80G49' CRCOff 'G28Z0' EOL
DoPartCycleComment
DoOpComments
DoPostScript
SeqC OpToolID EOL
SeqC ToolChng EOL
CheckPass
RETURN
NewToolOp4:
SeqC WFOStuff StrtPos CkSpeed EOL
RETURN
NewToolOp5:
SeqC OfstOn CoolOn EOL
RETURN
SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC Rapid AbsOrInc 'G49' CRCOff 'G28Z0M19' EOL { OfstOff }
SeqC SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC Rapid AbsOrInc 'G49' CRCOff 'G28Z0M19' EOL { OfstOff }
END
END
RETURN
SameToolOp2: {Start new Operation}
DoPartCycleComment
DoOpComments
DoPostScript
CheckPass
RETURN
SameToolOp3: {Start new Operation}
IF LAST ProgStop?
SeqC WFOStuff PlaneC AbsOrInc Rapid StrtPos CkSpeed EOL
SeqC OfstOn CoolOn EOL
ELSE
SeqC WFOStuff PlaneC AbsOrInc Rapid StrtPos CkSpeed EOL
IF NewToolOffset?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN
End1:
SeqC CoolOff EOL
SeqC Rapid AbsOrInc 'G49' CRCOff 'G28Z0M19' EOL { OfstOff }
RETURN
End2:
DoEndOpPS
SeqC 'G30X0Y0' EOL
IF ProgStop?
SeqC 'M0' EOL
END
RETURN
End3:
SeqC EOP EOL
EOR EOL
Post
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN
MPallTools1P: {Multiple Parts, All Tools 1 Part}
IF FirstOperation?
IF FirstPart?
InitOp
END
OpenMP
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
FirstOp2
OpenMP
FirstOp3
END
ELSE
IF NewTool?
IF FirstPart?
NewToolOp1
CloseMP
ResetWFO
NewToolOp2
NewToolOp3
NewToolOp4
OpenMP
NewToolOp5
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
FirstOp2
FirstOp3
OpenMP
END
ELSE
IF NewTool?
IF FirstPart?
CloseMP
NewToolOp1
ResetWFO
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
OpenMP
NewToolOp4
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
NoMPs: {no multiple parts}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
MasterSub:
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
RETURN
EndPartSub:
{End of program ************************************************************}
{finish last operation}
IF MultipleParts?
IF AllToolsOnePart?
End1
End2
CloseMP
ELSE {implied OneToolAllParts?}
IF FullUp?
End1
CloseMP
ResetWFO
End2
ELSE {implied ExitClearancePlane?}
CloseMP
End1
ResetWFO
End2
END
END
ELSE {NoMPs}
End1
End2
END
RETURN
DoNewPart:
IF NOT FirstPart?
{Finish off last Part}
IF FullUp?
SeqC CoolOff EOL
SeqC Rapid AbsOrInc 'G49' CRCOff 'G28Z0M19' EOL { OfstOff }
END
{DoEndOpPS}
{Start new Part}
DoPartCycleComment
DoOpComments
DoPostScript
WFOStuff
CheckPass
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF FullUp?
SeqC OfstOn CoolOn EOL
END
END
RETURN
DoParts:
TagInit
EachPart
TagInc
EachOp
IF AllToolsOnePart?
MasterSub
ELSE { OneToolAllParts }
IF GTEqual? Operation# Recall# Num#('1') { Tool First Op }
IF LTEqual? Operation# Recall# Num#('2') { Tool Last Op }
IF Equal? Operation# Recall# Num#('1') { Tool First Op }
DoNewPart
END
MasterSub
END
END
END
NextOp
IF AllToolsOnePart?
EndPartSub
END
NextPart
RETURN
GetToolFirstOp:
Save# Num#('2') Recall# Num#('1')
RETURN
GetToolLastOP:
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
RETURN
MPLoop:
IF AllToolsOnePart?
DoParts
ELSE { OneToolAllParts }
GetToolFirstOp
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
GetToolLastOP
DoParts
Save# Num#('1') ADD# Recall# Num#('2') Num#('1') { Next Tool First Op }
END
END
RETURN
{Start of executable Prog, Top Level ****}
ProgStart {setup and initializations}
IF MultipleParts?
IF WorkFixtureOffsets?
{'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'Therefore, the output will be controlled by the following values that are' EOL
'already entered in Equally Spaced Offsets Edit Fields:' EOL
'X' PartShiftX# ' Y' PartShiftY# ' Z' PartShiftZ# EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL}
IF NotEqual? PartShiftX# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftY# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftZ# Num#('0')
BadMPWFOReport
END
END
END
END
EachOp
IF FirstOperation?
Save# Num#('1') Operation#
ELSE
IF LastOp?
Save# Num#('3') Operation#
END
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
ELSE
ResetWFO
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
End3
Wyszukiwarka
Podobne podstrony:
Mit 500M Comet [DM] MU46 89Fadal Format 1 LH AI MV41 89 1Dynapath 20M LH [PC] MV20 89Juaristi LH [GT] MY76 89 3Fanuc 3000C Mat LH PM M495 89 3Fanuc 11M Demo LH [TI] MU21 89Fadal 2 LH [AIM] MY42 89 1Fadal Format 1 LH [FC] MU73 89 1Fadal Format 1 LH [PV] MU74 89Fanuc 15M Mon LH [RI] MU56 89 1Fadal Format 1 LH [CC] MU17 89Fadal Format 2 LH WT MX53 89 4Fanuc 6M Kuraki LH FES MW33 89Mit Meldas MO Comet [RL] MT72 89Centurion V LH [TPIS] MV82 89więcej podobnych podstron