13 47 Sealing flanges and flywheel drive plate


Sealing flanges and flywheel/drive plate, removing and installing Page 1 of 20
13-47
Sealing flanges and
flywheel/drive plate, removing
and installing
Note:
For repairs to the clutch:
Repair Manual, 5 Spd. Manual Transmission
012/01W Front Wheel Drive, Repair Group 30
Repair Manual, 5 Spd. Manual Transmission
01A All Wheel Drive, Repair Group 30
1 -
Sealing flange - front
Must be located on dowel sleeves
Removing and installing Page 13-56 .
2 -
15 Nm
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 2 of 20
13-48
3 -
Sealing ring
Replacing Page 13-51
Do not oil sealing lip of oil seal
4 -
Sump
Removing and installing Page 17-11
5 -
15 Nm
6 -
Cylinder block
Removing and installing crankshaft
Page 13-67 .
Dismantling and assembling pistons and
conrods Page 13-79 .
7 -
Dual-mass flywheel/drive plate
Removing and installing dual mass
flywheel Page 13-62
Removing and installing drive plate
Page 13-64
Can only be installed in one position. Holes
are offset.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 3 of 20
13-49
8 -
Securing bolt for dual-mass flywheel or
drive plate
Always replace
Tightening torque for dual mass flywheel
Page 13-63
Tightening torque for drive plate (vehicles
with automatic gearbox) Page 13-66
9 -
Intermediate plate
Must be located on dowel sleeves
Do not damage/bend when assembling
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 4 of 20
13-50
10 -
15 Nm
11 -
Rear sealing flange with oil seal
With gasket for cylinder block
Do not oil sealing lip of oil seal
Make sure that the sealing lip of the sealing
ring is not folded back or damaged when
installing
Removal and installation, removing sump
Page 17-11
When installing, push guide sleeve from
repair kit onto crankshaft
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 5 of 20
13-51
Crankshaft oil seal on pulley end,
replacing
Special tools and equipment
Oil seal extractor 3203
Holding tool 3415
Assembly tool T10053
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 6 of 20
13-52
Removing
Engine in vehicle
Lock carrier must be in service position
Page 13-1 .
- Remove toothed belt Page 13-40 .
- Unbolt stop for torque reaction support -arrows-.
- Remove toothed belt sprocket from crankshaft. To do this, counter hold
sprocket with 3415.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 7 of 20
13-53
- Before applying oil seal extractor, thread central
bolt for toothed belt sprocket into crankshaft as
far as it will go.
- Remove inner section of oil seal extractor 3203
one turn out of outer section and lock with
knurled screw.
- Lubricate threaded head of oil seal extractor, place it in position and
exerting firm pressure, screw it into oil seal as far as possible.
- Loosen knurled screw and turn inner part against crankshaft until the
oil seal is pulled out.
- Clamp flats of oil seal extractor in vice. Remove oil seal with pliers.
- Clean contact surface and sealing surface.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 8 of 20
13-54
Installing
Note:
Do not lubricate sealing lip or outer
circumference of seal before pressing in.
- Place guide sleeve T10053/1 onto crankshaft journal.
- Slide oil seal over guide sleeve.
- Press sealing ring flush with central bolt of toothed belt sprocket and
pressure sleeve from T10053.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 9 of 20
13-55
- Replace central bolt for toothed belt sprocket.
- Remove crankshaft toothed belt sprocket. To do this, counter-hold
toothed belt sprocket with 3415.
Note:
Contact surface between sprocket and crankshaft must be free of oil.
Do not oil bolt for crankshaft sprocket.
- Install toothed belt (adjust valve timing) Page 13-44 .
- Install ribbed belt and tensioner for ribbed belt Page 13-20 .
- Install lock carrier Page 13-1 .
Tightening torque
Component Nm
1)2)
Toothed belt sprocket to crankshaft
90 + 90
1)
Replace bolt
2)
90 corresponds to a quarter turn
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 10 of 20
13-56
Front sealing flange, removing and
installing
Special tools, material and equipment
Holding tool 3415
Assembly tool T10053
Electric drill with plastic brush attachment
Protective goggles
Silicone sealant D 176 404 A2
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 11 of 20
13-57
Removing
Engine in vehicle
Lock carrier must be in service position
Page 13-1 .
- Remove toothed belt Page 13-40 .
CAUTION!
The air conditioner refrigerant circuit must
not be opened.
- Disconnect A/C compressor from bracket and
secure to body with wire.
- Unbolt bracket for A/C compressor -Item 5 -,
Page 13-15
- Unbolt stop for torque reaction support -arrows-.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 12 of 20
13-58
- Remove toothed belt sprocket from crankshaft. To do this, counter hold
sprocket with 3415.
- Remove oil pan Page 17-11
- Remove bolts -1 to 6-.
- Pry sealing flange loose and remove.
- Carefully remove any remains of sealant from cylinder block.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 13 of 20
13-59
- Remove remaining sealant from sealing flange with rotating plastic
brush.
WARNING!
Wear protective glasses.
- Clean sealing surfaces: they must be free of oil and grease.
Installing
Note:
The sealing flange must be installed within 5 minutes after applying
silicone sealant.
- Cut off nozzle of silicon sealant tube at front marking (diameter of
nozzle = approx. 3 mm).
Silicone sealant D 176 404 A2
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 14 of 20
13-60
- Apply bead of silicone sealant -arrow-onto clean sealing surface of
sealing flange, as illustrated (arrow).
Sealant bead width -arrows-: 2 to 3 mm
Note:
The bead of sealant must not be thicker than 3 mm, otherwise excess
sealant will enter the oil pan and obstruct the strainer in the oil intake line.
- Install sealing flange immediately, and tighten all bolts lightly.
Note:
Use guide sleeve T10053/1 to attach the sealing flange with sealing ring
installed.
- Tighten sealing flange bolts in diagonal sequence.
- Install oil pan Page 17-23 .
Note:
After assembly, the sealant must dry for approx. 30 min. Only then may
the engine be filled with oil.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 15 of 20
13-61
- Install crankshaft oil seal Page 13-54 .
- Install toothed belt (adjust valve timing) Page
13-44 .
- Install bracket for A/C compressor -Item 5 -,
Page 13-15 .
- Install lock carrier Page 13-1 .
Tightening torques
Component Nm
Sealing flange to cylinder block 15
Bracket for air conditioner compressor on
cylinder block
33
A/C compressor to bracket 25
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 16 of 20
13-62
Dual mass flywheel/drive plate,
removing and installing
Dual-mass flywheel
Special tools and equipment
Counter-hold tool 10-201
Removing
- Reverse position of counter-hold tool 10-201 for loosening/tightening
bolts.
- Mark position of flywheel relative to engine.
- Unbolt flywheel.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 17 of 20
13-63
Installing
Installation is carried out in the reverse order or
removal; note the following:
- Replace bolts.
Tightening torque
Component Nm
2)
Dual-mass 22.5 mm
60 + 90
1)
flywheel
on crankshaft
43 mm 1) 60 + 180
3)
1)
Bolt length
2)
90 corresponds to a quarter turn
3)
180 = 1/2 turn
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 18 of 20
13-64
Drive plate
Special tools and equipment
Counter hold VW 558
Hex bolt M8 x 45 and two M10 hex nuts
Caliper gauge or depth measure
Removing
- Secure counter hold tool VW 558 to drive plate with hex bolt M8 x 45 -
Item 2-. Place two M10 hex nuts between counter-hold tool and drive
plate.
- Mark position of drive plate relative to engine.
- Unbolt drive plate.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 19 of 20
13-65
Installing
- Place drive plate in position with shim -2- and washer -1-. Lug -arrow-
must face towards torque converter.
- Insert at least 3 old securing bolts and tighten to 30 Nm.
- Measure distance -a- at three points and calculate average value.
Specified value: 18.9 to 20.5 mm
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002
Sealing flanges and flywheel/drive plate, removing and installing Page 20 of 20
13-66
If nominal value is exceeded:
- Remove drive plate again and fit without shim -2-. Retighten bolts to 30
Nm.
- Measure distance again.
If specified value is attained:
- Install new bolts and tighten.
Tightening torque
Component Nm
1)
Drive plate to crankshaft
60 + 90
1)
90 corresponds to a quarter turn
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.GE06.13.2 11/21/2002


Wyszukiwarka

Podobne podstrony:
13 4 Cylinder block crankshaft and flywheel service
EV (Electric Vehicle) and Hybrid Drive Systems
13 (47)
13 Interoperability, data discovery and access The e infrastructures for earth sciences resources
13 79 Pistons and connecting rods assembly
How to Install And Run Windows XP From USB drive
13 Frija and Other Goddesses
47 13 Rear calipers
47 (13)
[13]Role of oxidative stress and protein oxidation in the aging process
Murat Akser Memory, Identity and Desire A Psychoanalytic Reading of Lynch s Mulholland Drive
47 (13)
Deftones ? Qiet And Drive (Far Away)
CWIHP Bulletin nr 12 13 Director s note and table of contests
13 International meteorological and magnetic co operations in polar regions
keyboard and console howto 13 sle5wuropxbu5kef6tubetg42jvdpo3fvoqt66y

więcej podobnych podstron