AMERICA'S FAVORITE
U-BILD
WOODWORKING PLANS
Storage Bins
Plan No. 797
Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
A true country classic, this build-it-yourself storage bin
unit is a practical, convenient and attractive way to keep
apples, potatoes, onions and other fruits and vegetables
fresh and dry. The secret is the wire mesh on the front of
each of the three bins that allows air to circulate freely
around the produce.
The top shelf is flat for storing canned goods or
dish towels. The two pull-out bins below, each measuring
10 inches deep by 15 inches wide, are sized to hold plenty
of fruits and vegetables. The unit adds some old-fashioned
charm to the kitchen, too.
Because the curved cuts for the lower bins and
base are traced from full-size patterns, the project is easy
enough for novices.
The project measures 40 inches tall by 19 inches
wide by 12 inches deep.
Bill of Material
Cutting Schedule
Quantity Size Material Item
Item Qty T W L Material
1 1 x 2 x 83 pine D, N
A 2 3/4 11 39 1/4 pine
1 1 x 3 x 171 pine E, F, H, I, M
B 3 3/4 11 16 1/2 pine
1 1 x 8 x 40 pine G
C 1 3/4 16 1/2 * 39 1/4 pine
1 1 x 10 x 122 pine C, J, K
D 2 3/4 1 1/2 39 1/4 pine
1 1 x 12 x 171 pine A, B, L
E 1 3/4 2 15 pine
3 7 3/4 x 11 3/4 1/2 x 1/2 wire mesh
F 1 3/4 2 15 pine
3 pairs 1 3/8 x 2 butt hinges
G 1 3/4 12 1/4 * 19 pine
31 porcelain knobs
H 6 3/4 2 10 7/8 pine
1 friction lid support
I 6 3/4 2 10 7/8 pine
1 magnetic catch
J 2 3/4 9 1/4 13 3/8 pine
1 box 1 1/4 finish nails
K 2 3/4 3 3/4 13 3/8 pine
1 bottle wood glue
L 4 3/4 10 7/8 10 pine
1 can wood filler
M 2 3/4 2 3 pine
1 quart finish of choice
N 1 3/4 1 1/4 2 1/2 pine
*Edge-gluing required to achieve width.
NOTES
1. Read manufacturer s instructions before operating equipment.
2. Always wear safety glasses.
3. Edge-gluing may be required to achieve the necessary width of some pieces (see Cutting Schedule).
Isometric
G
M
C
E
A
B
D
L
H
F
K
I
J
G
M M E
B
H
A
C
11 TYP. I
L
K
H
J
B
F
Side View
D
I
A
H
B
F
C
Front View
Figure 1
Pattern 1
A
2 1 1/4
Board A
Pattern 1 Position
Board A
Pattern 1
Figure 2
Pattern 2
(See Front View for Position)
F
Board F
Pattern 2
1
Figure 3
Pattern 3
2
10 7/8
1
L
3 3/4
10
Board L
Pattern 3 Position
2
Assembly Instructions
Page One
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
1. Trace Pattern 1 onto the bottom end of boards (A), cut out curves and sand. Refer to Figure 1, Side View and Isometric.
2. Trace Pattern 2 onto the bottom edge of board (F), cut out curves and sand. Refer to Figure 2 and Isometric.
3. Trace Pattern 3 onto boards (L), cut out curves and sand. Refer to Figure 3, Side View and Isometric.
4. Cut a 3/4 by 3/4 notch on the front cor-
ners of shelf boards (B). Refer to Figure 4. 3/4 3/4
B
3/4 3/4
Figure 4
Board B
5. Attach shelf boards (B) to back board (C) using glue and 1 1/4 finish nails. Note: notched edges of boards (B) face the front
of the project. Refer to Side View and Isometric.
6. Attach sides (A) to subassembly (B, C) using glue and 1 1/4 finish nails. Refer to Front View, Side View and Isometric.
7. Assemble face frame (D, E, F) using glue. Refer to Front View and Isometric.
8. Attach face frame (D, E, F) to subassembly (A, B, C) using glue and 1 1/4 finish nails. Refer to Front View, Side View and
Isometric.
1/8
1/2
9. Cut a 1/8 wide by 1/2 deep dado on the center of the inside edges of door
frame boards (H) and (I). Refer to Figures 5 and 6, Front View and Side View.
H, I
Figure 5
Boards H, I
CENTER
LINE
Assembly Instructions
Page Two
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
10. Apply finish of choice to door frame boards (H) and (I).
11. Insert 7 3/4 by 11 3/4 wire mesh panels into dados
in door frame boards (H) and (I). With the wire mesh
panels in place, assemble door frame (H, I) using
glue. Refer to Figure 6 and Isometric.
I
12. Once door frames (H, I) are assembled, fill void
space on the ends of boards (I) with wood filler.
Refer to Figure 6.
1/8 wide by 1/2 deep dado
Fill w/
wood
filler
H
Figure 6
Door Detail
13. Attach bin back (K) to bin bottom (J) using glue and 1 1/4 finish nails. Refer to Side View and Isometric.
14. Attach bin sides (L) to subassemblies (J, K) using glue and 1 1/4 finish nails. Refer to Side View and Isometric.
15. Attach door frames (H, I) to bin subassemblies (J, K, L) using glue and 1 1/4 finish nails. Refer to Side View and Isometric.
16. Attach cabinet top (G) to boards (A), (C) and (E) using glue and 1 1/4 finish nails. Refer to Side View and Isometric.
17. Glue boards (M) together to create a 3 wide by 2 tall by 1 1/2 thick block. Refer to Side View and Isometric.
18. Attach subassembly (M, M) to the center of and flush with the top with board of (E). Refer to Side View and Isometric.
19. Sand and apply finish to the project.
20. Attach bins (H, I, J, K, L) and top door (H, I) to boards of (B) using 2 butt hinges. Refer to Front and Side Views.
21. Attach knobs to upper boards (H). Center knob on board. Refer to Side View.
22. Using lid support as a guide, install lid support mounting board (N) to inside of top cabinet.
23. Attach lid support to mounting board (N) and inside of top door frame (H, I). Refer to manufacturer s instructions.
Wyszukiwarka
Podobne podstrony:
Cabinet storage towerCabinet Storage CabinetStorage CabinetHand Tool Storage CabinetCabinet maple storage cabinet and easelCabinet Shaker Storage CabinetCabinet spice cabinetCabinet entertainment center2Nyx Password Storage 1 21 readmeThe Cabinet Of Dr Caligaricabinet bathroom 2Cabinet One door iceboxCabinet Entertainment Center BasicCabinet modern wardrobeCabinet linen closetwięcej podobnych podstron