CODEX ALIMENTARIUS


CAC/RCP 1-1969, Rev.4- 2003
Page 1 of 31
RECOMMENDED INTERNATIONAL CODE OF PRACTICE
GENERAL PRINCIPLES OF FOOD HYGIENE
CAC/RCP 1-1969, Rev. 4-20031
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................................................3
SECTION I - OBJECTIVES............................................................................................................................................3
THE CODEX GENERAL PRINCIPLES OF FOOD HYGIENE:...................................................................................................3
SECTION II - SCOPE, USE AND DEFINITION..........................................................................................................3
2.1 SCOPE....................................................................................................................................................................3
2.2 USE........................................................................................................................................................................4
2.3 DEFINITIONS..........................................................................................................................................................5
SECTION III - PRIMARY PRODUCTION ..................................................................................................................5
3.1 ENVIRONMENTAL HYGIENE ...................................................................................................................................6
3.2 HYGIENIC PRODUCTION OF FOOD SOURCES............................................................................................................6
3.3 HANDLING, STORAGE AND TRANSPORT .................................................................................................................6
3.4 CLEANING, MAINTENANCE AND PERSONNEL HYGIENE AT PRIMARY PRODUCTION .................................................6
SECTION IV - ESTABLISHMENT: DESIGN AND FACILITIES ............................................................................7
4.1 LOCATION .............................................................................................................................................................7
4.2 PREMISES AND ROOMS...........................................................................................................................................8
4.3 EQUIPMENT ...........................................................................................................................................................8
4.4 FACILITIES.............................................................................................................................................................9
SECTION V - CONTROL OF OPERATION..............................................................................................................11
5.1 CONTROL OF FOOD HAZARDS ..............................................................................................................................11
5.2 KEY ASPECTS OF HYGIENE CONTROL SYSTEMS ....................................................................................................11
5.3 INCOMING MATERIAL REQUIREMENTS .................................................................................................................13
5.4 PACKAGING.........................................................................................................................................................13
5.5 WATER ................................................................................................................................................................13
5.6 MANAGEMENT AND SUPERVISION .......................................................................................................................13
5.7 DOCUMENTATION AND RECORDS.........................................................................................................................14
5.8 RECALL PROCEDURES..........................................................................................................................................14
SECTION VI - ESTABLISHMENT: MAINTENANCE AND SANITATION.........................................................14
6.1 MAINTENANCE AND CLEANING ...........................................................................................................................14
6.2 CLEANING PROGRAMMES ....................................................................................................................................15
6.3 PEST CONTROL SYSTEMS .....................................................................................................................................15
6.4 WASTE MANAGEMENT.........................................................................................................................................16
6.5 MONITORING EFFECTIVENESS..............................................................................................................................16
SECTION VII - ESTABLISHMENT: PERSONAL HYGIENE ................................................................................16
7.1 HEALTH STATUS ..................................................................................................................................................17
7.2 ILLNESS AND INJURIES.........................................................................................................................................17
7.3 PERSONAL CLEANLINESS .....................................................................................................................................17
7.4 PERSONAL BEHAVIOUR........................................................................................................................................17
7.5 VISITORS .............................................................................................................................................................18
1
The current version of the Recommended International Code of Practice-General Principles of Food Hygiene
including Annex on Hazard Analysis and Critical Control Point (HACCP) System and Guidelines for its Application was
adopted by the Codex Alimentarius Commission in 1997. Amendments regarding rinsing adopted in 1999. HACCP
Guidelines were revised in 2003. The Code has been sent to all Member Nations and Associate Members of FAO and WHO
as an advisory text, and it is for individual governments to decide what use they wish to make of the Guidelines.
CAC/RCP 1-1969, Rev.4- 2003
Page 2 of 31
SECTION VIII - TRANSPORTATION .......................................................................................................................18
8.1 GENERAL.............................................................................................................................................................18
8.2 REQUIREMENTS ...................................................................................................................................................18
8.3 USE AND MAINTENANCE......................................................................................................................................18
SECTION IX - PRODUCT INFORMATION AND CONSUMER AWARENESS..................................................19
9.1 LOT IDENTIFICATION ...........................................................................................................................................19
9.2 PRODUCT INFORMATION......................................................................................................................................19
9.3 LABELLING..........................................................................................................................................................19
9.4 CONSUMER EDUCATION.......................................................................................................................................19
SECTION X - TRAINING .............................................................................................................................................20
10.1 AWARENESS AND RESPONSIBILITIES ...............................................................................................................20
10.2 TRAINING PROGRAMMES ................................................................................................................................20
10.3 INSTRUCTION AND SUPERVISION.....................................................................................................................20
10.4 REFRESHER TRAINING.....................................................................................................................................20
HAZARD ANALYSIS AND CRITICAL CONTROL POINT (HACCP) SYSTEM AND GUIDELINES
FOR ITS APPLICATION..............................................................................................................................................21
PREAMBLE....................................................................................................................................................................21
DEFINITIONS ................................................................................................................................................................21
PRINCIPLES OF THE HACCP SYSTEM ..................................................................................................................22
GUIDELINES FOR THE APPLICATION OF THE HACCP SYSTEM..................................................................24
INTRODUCTION...........................................................................................................................................................24
APPLICATION...............................................................................................................................................................24
TRAINING ......................................................................................................................................................................28
CAC/RCP 1-1969, Rev.4- 2003
Page 3 of 31
INTRODUCTION
People have the right to expect the food they eat to be safe and suitable for consumption.
Foodborne illness and foodborne injury are at best unpleasant; at worst, they can be fatal. But
there are also other consequences. Outbreaks of foodborne illness can damage trade and tourism,
and lead to loss of earnings, unemployment and litigation. Food spoilage is wasteful, costly and
can adversely affect trade and consumer confidence.
International food trade, and foreign travel, are increasing, bringing important social and
economic benefits. But this also makes the spread of illness around the world easier. Eating
habits too, have undergone major change in many countries over the last two decades and new
food production, preparation and distribution techniques have developed to reflect this. Effective
hygiene control, therefore, is vital to avoid the adverse human health and economic consequences
of foodborne illness, foodborne injury, and food spoilage. Everyone, including farmers and
growers, manufacturers and processors, food handlers and consumers, has a responsibility to
assure that food is safe and suitable for consumption.
These General Principles lay a firm foundation for ensuring food hygiene and should be used in
conjunction with each specific code of hygienic practice, where appropriate, and the guidelines on
microbiological criteria. The document follows the food chain from primary production through
to final consumption, highlighting the key hygiene controls at each stage. It recommends a
HACCP-based approach wherever possible to enhance food safety as described in Hazard
Analysis and Critical Control Point (HACCP) System and Guidelines for its Application (Annex).
The controls described in this General Principles document are internationally recognized as
essential to ensure the safety and suitability of food for consumption. The General Principles are
commended to Governments, industry (including individual primary producers, manufacturers,
processors, food service operators and retailers) and consumers alike.
SECTION I - OBJECTIVES
1.1 THE CODEX GENERAL PRINCIPLES OF FOOD HYGIENE:
" identify the essential principles of food hygiene applicable throughout the food chain
(including primary production through to the final consumer), to achieve the goal of ensuring
that food is safe and suitable for human consumption;
" recommend a HACCP-based approach as a means to enhance food safety;
" indicate how to implement those principles; and
" provide a guidance for specific codes which may be needed for - sectors of the food chain;
processes; or commodities; to amplify the hygiene requirements specific to those areas.
SECTION II - SCOPE, USE AND DEFINITION
2.1 SCOPE
2.1.1 The food chain
This document follows the food chain from primary production to the final consumer, setting out
the necessary hygiene conditions for producing food which is safe and suitable for consumption.
The document provides a base-line structure for other, more specific, codes applicable to
particular sectors. Such specific codes and guidelines should be read in conjunction with this
CAC/RCP 1-1969, Rev.4- 2003
Page 4 of 31
document and Hazard Analysis and Critical Control Point (HACCP) System and Guidelines for
its Application (Annex).
2.1.2 Roles of Governments, industry, and consumers
Governments can consider the contents of this document and decide how best they should
encourage the implementation of these general principles to:
" protect consumers adequately from illness or injury caused by food; policies need to consider
the vulnerability of the population, or of different groups within the population;
" provide assurance that food is suitable for human consumption;
" maintain confidence in internationally traded food; and
" provide health education programmes which effectively communicate the principles of food
hygiene to industry and consumers.
Industry should apply the hygienic practices set out in this document to:
" provide food which is safe and suitable for consumption;
" ensure that consumers have clear and easily-understood information, by way of labelling and
other appropriate means, to enable them to protect their food from contamination and
growth/survival of foodborne pathogens by storing, handling and preparing it correctly; and
" maintain confidence in internationally traded food.
Consumers should recognize their role by following relevant instructions and applying
appropriate food hygiene measures.
2.2 USE
Each section in this document states both the objectives to be achieved and the rationale behind
those objectives in terms of the safety and suitability of food.
Section III covers primary production and associated procedures. Although hygiene practices
may differ considerably for the various food commodities and specific codes should be applied
where appropriate, some general guidance is given in this section. Sections IV to X set down the
general hygiene principles which apply throughout the food chain to the point of sale. Section IX
also covers consumer information, recognizing the important role played by consumers in
maintaining the safety and suitability of food.
There will inevitably be situations where some of the specific requirements contained in this
document are not applicable. The fundamental question in every case is  what is necessary and
appropriate on the grounds of the safety and suitability of food for consumption?
The text indicates where such questions are likely to arise by using the phrases  where necessary
and  where appropriate . In practice, this means that, although the requirement is generally
appropriate and reasonable, there will nevertheless be some situations where it is neither
necessary nor appropriate on the grounds of food safety and suitability. In deciding whether a
requirement is necessary or appropriate, an assessment of the risk should be made, preferably
within the framework of the HACCP approach. This approach allows the requirements in this
document to be flexibly and sensibly applied with a proper regard for the overall objectives of
producing food which is safe and suitable for consumption. In so doing it takes into account the
CAC/RCP 1-1969, Rev.4- 2003
Page 5 of 31
wide diversity of activities and varying degrees of risk involved in producing food. Additional
guidance is available in specific food codes.
2.3 DEFINITIONS
For the purpose of this Code, the following expressions have the meaning stated:
Cleaning - the removal of soil, food residue, dirt, grease or other objectionable matter.
Contaminant - any biological or chemical agent, foreign matter, or other substances not
intentionally added to food which may compromise food safety or suitability.
Contamination - the introduction or occurrence of a contaminant in food or food environment.
Disinfection - the reduction, by means of chemical agents and/or physical methods, of the number
of micro-organisms in the environment, to a level that does not compromise food safety or
suitability.
Establishment - any building or area in which food is handled and the surroundings under the
control of the same management.
Food hygiene - all conditions and measures necessary to ensure the safety and suitability of food
at all stages of the food chain.
Hazard - a biological, chemical or physical agent in, or condition of, food with the potential to
cause an adverse health effect.
HACCP - a system which identifies, evaluates, and controls hazards which are significant for food
safety.
Food handler - any person who directly handles packaged or unpackaged food, food equipment
and utensils, or food contact surfaces and is therefore expected to comply with food hygiene
requirements
Food safety - assurance that food will not cause harm to the consumer when it is prepared and/or
eaten according to its intended use.
Food suitability - assurance that food is acceptable for human consumption according to its
intended use.
Primary production - those steps in the food chain up to and including, for example, harvesting,
slaughter, milking, fishing.
SECTION III - PRIMARY PRODUCTION
OBJECTIVES:
Primary production should be managed in a way that ensures that food is safe and suitable for its
intended use. Where necessary, this will include:
- avoiding the use of areas where the environment poses a threat to the safety of food;
- controlling contaminants, pests and diseases of animals and plants in such a way as not to
pose a threat to food safety;
- adopting practices and measures to ensure food is produced under appropriately hygienic
conditions.
RATIONALE:
CAC/RCP 1-1969, Rev.4- 2003
Page 6 of 31
To reduce the likelihood of introducing a hazard which may adversely affect the safety of food, or
its suitability for consumption, at later stages of the food chain.
3.1 ENVIRONMENTAL HYGIENE
Potential sources of contamination from the environment should be considered. In particular,
primary food production should not be carried on in areas where the presence of potentially
harmful substances would lead to an unacceptable level of such substances in food.
1.2 3.2 HYGIENIC PRODUCTION OF FOOD SOURCES
The potential effects of primary production activities on the safety and suitability of food should
be considered at all times. In particular, this includes identifying any specific points in such
activities where a high probability of contamination may exist and taking specific measures to
minimize that probability. The HACCP-based approach may assist in the taking of such measures
- see Hazard Analysis and Critical Control (HACCP) Point System and Guidelines for its
Application (Annex).
Producers should as far as practicable implement measures to:
" control contamination from air, soil, water, feedstuffs, fertilizers (including natural fertilizers),
pesticides, veterinary drugs or any other agent used in primary production;
" control plant and animal health so that it does not pose a threat to human health through food
consumption, or adversely affect the suitability of the product; and
" protect food sources from faecal and other contamination.
In particular, care should be taken to manage wastes, and store harmful substances appropriately.
On-farm programmes which achieve specific food safety goals are becoming an important part of
primary production and should be encouraged.
3.3 HANDLING, STORAGE AND TRANSPORT
Procedures should be in place to:
" sort food and food ingredients to segregate material which is evidently unfit for human
consumption;
" dispose of any rejected material in a hygienic manner; and
" Protect food and food ingredients from contamination by pests, or by chemical, physical or
microbiological contaminants or other objectionable substances during handling, storage and
transport.
Care should be taken to prevent, so far as reasonably practicable, deterioration and spoilage
through appropriate measures which may include controlling temperature, humidity, and/or other
controls.
3.4 CLEANING, MAINTENANCE AND PERSONNEL HYGIENE AT PRIMARY PRODUCTION
Appropriate facilities and procedures should be in place to ensure that:
" any necessary cleaning and maintenance is carried out effectively; and
" an appropriate degree of personal hygiene is maintained.
CAC/RCP 1-1969, Rev.4- 2003
Page 7 of 31
SECTION IV - ESTABLISHMENT: DESIGN AND FACILITIES
OBJECTIVES:
Depending on the nature of the operations, and the risks associated with them, premises,
equipment and facilities should be located, designed and constructed to ensure that:
- contamination is minimized;
- design and layout permit appropriate maintenance, cleaning and disinfections and minimize
air-borne contamination;
- surfaces and materials, in particular those in contact with food, are non-toxic in intended
use and, where necessary, suitably durable, and easy to maintain and clean;
- where appropriate, suitable facilities are available for temperature, humidity and other
controls; and
- there is effective protection against pest access and harbourage.
RATIONALE:
Attention to good hygienic design and construction, appropriate location, and the provision of
adequate facilities, is necessary to enable hazards to be effectively controlled.
4.1 LOCATION
4.1.1 Establishments
Potential sources of contamination need to be considered when deciding where to locate food
establishments, as well as the effectiveness of any reasonable measures that might be taken to
protect food. Establishments should not be located anywhere where, after considering such
protective measures, it is clear that there will remain a threat to food safety or suitability. In
particular, establishments should normally be located away from:
" environmentally polluted areas and industrial activities which pose a serious threat of
contaminating food;
" areas subject to flooding unless sufficient safeguards are provided;
" areas prone to infestations of pests;
" areas where wastes, either solid or liquid, cannot be removed effectively.
4.1.2 Equipment
Equipment should be located so that it:
" permits adequate maintenance and cleaning;
" functions in accordance with its intended use; and
" facilitates good hygiene practices, including monitoring.
CAC/RCP 1-1969, Rev.4- 2003
Page 8 of 31
4.2 PREMISES AND ROOMS
4.2.1 Design and layout
Where appropriate, the internal design and layout of food establishments should permit good food
hygiene practices, including protection against cross-contamination between and during
operations by foodstuffs.
4.2.2 Internal structures and fittings
Structures within food establishments should be soundly built of durable materials and be easy to
maintain, clean and where appropriate, able to be disinfected. In particular the following specific
conditions should be satisfied where necessary to protect the safety and suitability of food:
" the surfaces of walls, partitions and floors should be made of impervious materials with no
toxic effect in intended use;
" walls and partitions should have a smooth surface up to a height appropriate to the operation;
" floors should be constructed to allow adequate drainage and cleaning;
" ceilings and overhead fixtures should be constructed and finished to minimize the build up of
dirt and condensation, and the shedding of particles;
" windows should be easy to clean, be constructed to minimize the build up of dirt and where
necessary, be fitted with removable and cleanable insect-proof screens. Where necessary,
windows should be fixed;
" doors should have smooth, non-absorbent surfaces, and be easy to clean and, where necessary,
disinfect;
" working surfaces that come into direct contact with food should be in sound condition, durable
and easy to clean, maintain and disinfect. They should be made of smooth, non-absorbent
materials, and inert to the food, to detergents and disinfectants under normal operating
conditions.
4.2.3 Temporary/mobile premises and vending machines
Premises and structures covered here include market stalls, mobile sales and street vending
vehicles, temporary premises in which food is handled such as tents and marquees.
Such premises and structures should be sited, designed and constructed to avoid, as far as
reasonably practicable, contaminating food and harbouring pests.
In applying these specific conditions and requirements, any food hygiene hazards associated with
such facilities should be adequately controlled to ensure the safety and suitability of food.
4.3 EQUIPMENT
4.3.1 General
Equipment and containers (other than once-only use containers and packaging) coming into
contact with food, should be designed and constructed to ensure that, where necessary, they can
be adequately cleaned, disinfected and maintained to avoid the contamination of food. Equipment
and containers should be made of materials with no toxic effect in intended use. Where
necessary, equipment should be durable and movable or capable of being disassembled to allow
CAC/RCP 1-1969, Rev.4- 2003
Page 9 of 31
for maintenance, cleaning, disinfection, monitoring and, for example, to facilitate inspection for
pests.
4.3.2 Food control and monitoring equipment
In addition to the general requirements in paragraph 4.3.1, equipment used to cook, heat treat,
cool, store or freeze food should be designed to achieve the required food temperatures as rapidly
as necessary in the interests of food safety and suitability, and maintain them effectively. Such
equipment should also be designed to allow temperatures to be monitored and controlled. Where
necessary, such equipment should have effective means of controlling and monitoring humidity,
air-flow and any other characteristic likely to have a detrimental effect on the safety or suitability
of food. These requirements are intended to ensure that:
" harmful or undesirable micro-organisms or their toxins are eliminated or reduced to safe levels
or their survival and growth are effectively controlled;
" where appropriate, critical limits established in HACCP-based plans can be monitored; and
" temperatures and other conditions necessary to food safety and suitability can be rapidly
achieved and maintained.
4.3.3 Containers for waste and inedible substances
Containers for waste, by-products and inedible or dangerous substances, should be specifically
identifiable, suitably constructed and, where appropriate, made of impervious material.
Containers used to hold dangerous substances should be identified and, where appropriate, be
lockable to prevent malicious or accidental contamination of food.
4.4 FACILITIES
4.4.1 Water supply
An adequate supply of potable water with appropriate facilities for its storage, distribution and
temperature control, should be available whenever necessary to ensure the safety and suitability of
food.
Potable water should be as specified in the latest edition of WHO Guidelines for Drinking Water
Quality, or water of a higher standard. Non-potable water (for use in, for example, fire control,
steam production, refrigeration and other similar purposes where it would not contaminate food),
shall have a separate system. Non-potable water systems shall be identified and shall not connect
with, or allow reflux into, potable water systems.
4.4.2 Drainage and waste disposal
Adequate drainage and waste disposal systems and facilities should be provided. They should be
designed and constructed so that the risk of contaminating food or the potable water supply is
avoided.
4.4.3 Cleaning
Adequate facilities, suitably designated, should be provided for cleaning food, utensils and
equipment. Such facilities should have an adequate supply of hot and cold potable water where
appropriate.
CAC/RCP 1-1969, Rev.4- 2003
Page 10 of 31
4.4.4 Personnel hygiene facilities and toilets
Personnel hygiene facilities should be available to ensure that an appropriate degree of personal
hygiene can be maintained and to avoid contaminating food. Where appropriate, facilities should
include:
" adequate means of hygienically washing and drying hands, including wash basins and a
supply of hot and cold (or suitably temperature controlled) water;
" lavatories of appropriate hygienic design; and
" adequate changing facilities for personnel.
Such facilities should be suitably located and designated.
4.4.5 Temperature control
Depending on the nature of the food operations undertaken, adequate facilities should be available
for heating, cooling, cooking, refrigerating and freezing food, for storing refrigerated or frozen
foods, monitoring food temperatures, and when necessary, controlling ambient temperatures to
ensure the safety and suitability of food.
4.4.6 Air quality and ventilation
Adequate means of natural or mechanical ventilation should be provided, in particular to:
" minimize air-borne contamination of food, for example, from aerosols and condensation
droplets;
" control ambient temperatures;
" control odours which might affect the suitability of food; and
" control humidity, where necessary, to ensure the safety and suitability of food.
Ventilation systems should be designed and constructed so that air does not flow from
contaminated areas to clean areas and, where necessary, they can be adequately maintained and
cleaned.
4.4.7 Lighting
Adequate natural or artificial lighting should be provided to enable the undertaking to operate in a
hygienic manner. Where necessary, lighting should not be such that the resulting colour is
misleading. The intensity should be adequate to the nature of the operation. Lighting fixtures
should, where appropriate, be protected to ensure that food is not contaminated by breakages.
4.4.8 Storage
Where necessary, adequate facilities for the storage of food, ingredients and non-food chemicals
(e.g. cleaning materials, lubricants, fuels) should be provided.
Where appropriate, food storage facilities should be designed and constructed to:
" permit adequate maintenance and cleaning;
" avoid pest access and harbourage;
" enable food to be effectively protected from contamination during storage; and
CAC/RCP 1-1969, Rev.4- 2003
Page 11 of 31
" where necessary, provide an environment which minimizes the deterioration of food (e.g. by
temperature and humidity control).
The type of storage facilities required will depend on the nature of the food. Where necessary,
separate, secure storage facilities for cleaning materials and hazardous substances should be
provided.
SECTION V - CONTROL OF OPERATION
OBJECTIVE:
To produce food which is safe and suitable for human consumption by:
- formulating design requirements with respect to raw materials, composition, processing,
distribution, and consumer use to be met in the manufacture and handling of specific food
items; and
- designing, implementing, monitoring and reviewing effective control systems.
RATIONALE:
To reduce the risk of unsafe food by taking preventive measures to assure the safety and
suitability of food at an appropriate stage in the operation by controlling food hazards.
5.1 CONTROL OF FOOD HAZARDS
Food business operators should control food hazards through the use of systems such as HACCP.
They should:
" identify any steps in their operations which are critical to the safety of food;
" implement effective control procedures at those steps;
" monitor control procedures to ensure their continuing effectiveness; and
" review control procedures periodically, and whenever the operations change.
These systems should be applied throughout the food chain to control food hygiene throughout
the shelf-life of the product through proper product and process design.
Control procedures may be simple, such as checking stock rotation calibrating equipment, or
correctly loading refrigerated display units. In some cases a system based on expert advice, and
involving documentation, may be appropriate. A model of such a food safety system is described
in Hazard Analysis and Critical Control (HACCP) System and Guidelines for its Application
(Annex).
5.2 KEY ASPECTS OF HYGIENE CONTROL SYSTEMS
5.2.1 Time and temperature control
Inadequate food temperature control is one of the most common causes of foodborne illness or
food spoilage. Such controls include time and temperature of cooking, cooling, processing and
storage. Systems should be in place to ensure that temperature is controlled effectively where it is
critical to the safety and suitability of food.
Temperature control systems should take into account:
CAC/RCP 1-1969, Rev.4- 2003
Page 12 of 31
" the nature of the food, e.g. its water activity, pH, and likely initial level and types of micro-
organisms;
" the intended shelf-life of the product;
" the method of packaging and processing; and
" how the product is intended to be used, e.g. further cooking/processing or ready-to-eat.
Such systems should also specify tolerable limits for time and temperature variations.
Temperature recording devices should be checked at regular intervals and tested for accuracy.
5.2.2 Specific process steps
Other steps which contribute to food hygiene may include, for example:
" chilling
" thermal processing
" irradiation
" drying
" chemical preservation
" vacuum or modified atmospheric packaging
5.2.3 Microbiological and other specifications
Management systems described in paragraph 5.1 offer an effective way of ensuring the safety and
suitability of food. Where microbiological, chemical or physical specifications are used in any
food control system, such specifications should be based on sound scientific principles and state,
where appropriate, monitoring procedures, analytical methods and action limits.
5.2.4 Microbiological cross-contamination
Pathogens can be transferred from one food to another, either by direct contact or by food
handlers, contact surfaces or the air. Raw, unprocessed food should be effectively separated,
either physically or by time, from ready-to-eat foods, with effective intermediate cleaning and
where appropriate disinfection.
Access to processing areas may need to be restricted or controlled. Where risks are particularly
high, access to processing areas should be only via a changing facility. Personnel may need to be
required to put on clean protective clothing including footwear and wash their hands before
entering.
Surfaces, utensils, equipment, fixtures and fittings should be thoroughly cleaned and where
necessary disinfected after raw food, particularly meat and poultry, has been handled or
processed.
5.2.5 Physical and chemical contamination
Systems should be in place to prevent contamination of foods by foreign bodies such as glass or
metal shards from machinery, dust, harmful fumes and unwanted chemicals. In manufacturing
and processing, suitable detection or screening devices should be used where necessary.
CAC/RCP 1-1969, Rev.4- 2003
Page 13 of 31
5.3 INCOMING MATERIAL REQUIREMENTS
No raw material or ingredient should be accepted by an establishment if it is known to contain
parasites, undesirable micro-organisms, pesticides, veterinary drugs or toxic, decomposed or
extraneous substances which would not be reduced to an acceptable level by normal sorting
and/or processing. Where appropriate, specifications for raw materials should be identified and
applied.
Raw materials or ingredients should, where appropriate, be inspected and sorted before
processing. Where necessary, laboratory tests should be made to establish fitness for use. Only
sound, suitable raw materials or ingredients should be used.
Stocks of raw materials and ingredients should be subject to effective stock rotation.
5.4 PACKAGING
Packaging design and materials should provide adequate protection for products to minimize
contamination, prevent damage, and accommodate proper labelling. Packaging materials or gases
where used must be non-toxic and not pose a threat to the safety and suitability of food under the
specified conditions of storage and use. Where appropriate, reusable packaging should be
suitably durable, easy to clean and, where necessary, disinfect.
5.5 WATER
5.5.1 In contact with food
Only potable water, should be used in food handling and processing, with the following
exceptions:
" for steam production, fire control and other similar purposes not connected with food; and
" in certain food processes, e.g. chilling, and in food handling areas, provided this does not
constitute a hazard to the safety and suitability of food (e.g. the use of clean sea water).
Water recirculated for reuse should be treated and maintained in such a condition that no risk to
the safety and suitability of food results from its use. The treatment process should be effectively
monitored. Recirculated water which has received no further treatment and water recovered from
processing of food by evaporation or drying may be used, provided its use does not constitute a
risk to the safety and suitability of food.
5.5.2 As an ingredient
Potable water should be used wherever necessary to avoid food contamination.
5.5.3 Ice and steam
Ice should be made from water that complies with section 4.4.1. Ice and steam should be
produced, handled and stored to protect them from contamination.
Steam used in direct contact with food or food contact surfaces should not constitute a threat to
the safety and suitability of food.
5.6 MANAGEMENT AND SUPERVISION
The type of control and supervision needed will depend on the size of the business, the nature of
its activities and the types of food involved. Managers and supervisors should have enough
knowledge of food hygiene principles and practices to be able to judge potential risks, take
CAC/RCP 1-1969, Rev.4- 2003
Page 14 of 31
appropriate preventive and corrective action, and ensure that effective monitoring and supervision
takes place.
5.7 DOCUMENTATION AND RECORDS
Where necessary, appropriate records of processing, production and distribution should be kept
and retained for a period that exceeds the shelf-life of the product. Documentation can enhance
the credibility and effectiveness of the food safety control system.
5.8 RECALL PROCEDURES
Managers should ensure effective procedures are in place to deal with any food safety hazard and
to enable the complete, rapid recall of any implicated lot of the finished food from the market.
Where a product has been withdrawn because of an immediate health hazard, other products
which are produced under similar conditions, and which may present a similar hazard to public
health, should be evaluated for safety and may need to be withdrawn. The need for public
warnings should be considered.
Recalled products should be held under supervision until they are destroyed, used for purposes
other than human consumption, determined to be safe for human consumption, or reprocessed in a
manner to ensure their safety.
SECTION VI - ESTABLISHMENT: MAINTENANCE AND SANITATION
OBJECTIVE:
To establish effective systems to:
- ensure adequate and appropriate maintenance and cleaning;
- control pests;
- manage waste; and
- monitor effectiveness of maintenance and sanitation procedures.
RATIONALE:
To facilitate the continuing effective control of food hazards, pests, and other agents likely to
contaminate food.
6.1 MAINTENANCE AND CLEANING
6.1.1 General
Establishments and equipment should be kept in an appropriate state of repair and condition to:
" facilitate all sanitation procedures;
" function as intended, particularly at critical steps (see paragraph 5.1);
" prevent contamination of food, e.g. from metal shards, flaking plaster, debris and chemicals.
Cleaning should remove food residues and dirt which may be a source of contamination. The
necessary cleaning methods and materials will depend on the nature of the food business.
Disinfection may be necessary after cleaning.
CAC/RCP 1-1969, Rev.4- 2003
Page 15 of 31
Cleaning chemicals should be handled and used carefully and in accordance with manufacturers
instructions and stored, where necessary, separated from food, in clearly identified containers to
avoid the risk of contaminating food.
6.1.2 Cleaning procedures and methods
Cleaning can be carried out by the separate or the combined use of physical methods, such as
heat, scrubbing, turbulent flow, vacuum cleaning or other methods that avoid the use of water, and
chemical methods using detergents, alkalis or acids.
Cleaning procedures will involve, where appropriate:
" removing gross debris from surfaces;
" applying a detergent solution to loosen soil and bacterial film and hold them in solution or
suspension;
" rinsing with water which complies with section 4, to remove loosened soil and residues of
detergent;
" dry cleaning or other appropriate methods for removing and collecting residues and debris;
and
" where necessary, disinfection with subsequent rinsing unless the manufacturers instructions
indicate on scientific basis that rinsing is not required.
6.2 CLEANING PROGRAMMES
Cleaning and disinfection programmes should ensure that all parts of the establishment are
appropriately clean, and should include the cleaning of cleaning equipment.
Cleaning and disinfection programmes should be continually and effectively monitored for their
suitability and effectiveness and where necessary, documented.
Where written cleaning programmes are used, they should specify:
" areas, items of equipment and utensils to be cleaned;
" responsibility for particular tasks;
" method and frequency of cleaning; and
" monitoring arrangements.
Where appropriate, programmes should be drawn up in consultation with relevant specialist
expert advisors.
6.3 PEST CONTROL SYSTEMS
6.3.1 General
Pests pose a major threat to the safety and suitability of food. Pest infestations can occur where
there are breeding sites and a supply of food. Good hygiene practices should be employed to
avoid creating an environment conducive to pests. Good sanitation, inspection of incoming
materials and good monitoring can minimize the likelihood of infestation and thereby limit the
need for pesticides.
CAC/RCP 1-1969, Rev.4- 2003
Page 16 of 31
6.3.2 Preventing access
Buildings should be kept in good repair and condition to prevent pest access and to eliminate
potential breeding sites. Holes, drains and other places where pests are likely to gain access
should be kept sealed. Wire mesh screens, for example on open windows, doors and ventilators,
will reduce the problem of pest entry. Animals should, wherever possible, be excluded from the
grounds of factories and food processing plants.
6.3.3 Harbourage and infestation
The availability of food and water encourages pest harbourage and infestation. Potential food
sources should be stored in pest-proof containers and/or stacked above the ground and away from
walls. Areas both inside and outside food premises should be kept clean. Where appropriate,
refuse should be stored in covered, pest-proof containers.
6.3.4 Monitoring and detection
Establishments and surrounding areas should be regularly examined for evidence of infestation.
6.3.5 Eradication
Pest infestations should be dealt with immediately and without adversely affecting food safety or
suitability. Treatment with chemical, physical or biological agents should be carried out without
posing a threat to the safety or suitability of food.
6.4 WASTE MANAGEMENT
Suitable provision must be made for the removal and storage of waste. Waste must not be
allowed to accumulate in food handling, food storage, and other working areas and the adjoining
environment except so far as is unavoidable for the proper functioning of the business.
Waste stores must be kept appropriately clean.
6.5 MONITORING EFFECTIVENESS
Sanitation systems should be monitored for effectiveness, periodically verified by means such as
audit pre-operational inspections or, where appropriate, microbiological sampling of environment
and food contact surfaces and regularly reviewed and adapted to reflect changed circumstances.
SECTION VII - ESTABLISHMENT: PERSONAL HYGIENE
OBJECTIVES:
To ensure that those who come directly or indirectly into contact with food are not likely to
contaminate food by:
- maintaining an appropriate degree of personal cleanliness;
- behaving and operating in an appropriate manner.
RATIONALE:
People who do not maintain an appropriate degree of personal cleanliness, who have certain
illnesses or conditions or who behave inappropriately, can contaminate food and transmit illness
to consumers.
CAC/RCP 1-1969, Rev.4- 2003
Page 17 of 31
7.1 HEALTH STATUS
People known, or suspected, to be suffering from, or to be a carrier of a disease or illness likely to
be transmitted through food, should not be allowed to enter any food handling area if there is a
likelihood of their contaminating food. Any person so affected should immediately report illness
or symptoms of illness to the management.
Medical examination of a food handler should be carried out if clinically or epidemiologically
indicated.
7.2 ILLNESS AND INJURIES
Conditions which should be reported to management so that any need for medical examination
and/or possible exclusion from food handling can be considered, include:
" jaundice;
" diarrhoea;
" vomiting;
" fever;
" sore throat with fever;
" visibly infected skin lesions (boils, cuts, etc.);
" discharges from the ear, eye or nose.
7.3 PERSONAL CLEANLINESS
Food handlers should maintain a high degree of personal cleanliness and, where appropriate, wear
suitable protective clothing, head covering, and footwear. Cuts and wounds, where personnel are
permitted to continue working, should be covered by suitable waterproof dressings.
Personnel should always wash their hands when personal cleanliness may affect food safety, for
example:
" at the start of food handling activities;
" immediately after using the toilet; and
" after handling raw food or any contaminated material, where this could result in contamination
of other food items; they should avoid handling ready-to-eat food, where appropriate.
7.4 PERSONAL BEHAVIOUR
People engaged in food handling activities should refrain from behaviour which could result in
contamination of food, for example:
" smoking;
" spitting;
" chewing or eating;
" sneezing or coughing over unprotected food.
CAC/RCP 1-1969, Rev.4- 2003
Page 18 of 31
Personal effects such as jewellery, watches, pins or other items should not be worn or brought into
food handling areas if they pose a threat to the safety and suitability of food.
7.5 VISITORS
Visitors to food manufacturing, processing or handling areas should, where appropriate, wear
protective clothing and adhere to the other personal hygiene provisions in this section.
SECTION VIII - TRANSPORTATION
OBJECTIVES:
Measures should be taken where necessary to:
- protect food from potential sources of contamination;
- protect food from damage likely to render the food unsuitable for consumption; and
- provide an environment which effectively controls the growth of pathogenic or spoilage
micro-organisms and the production of toxins in food.
RATIONALE:
Food may become contaminated, or may not reach its destination in a suitable condition for
consumption, unless effective control measures are taken during transport, even where adequate
hygiene control measures have been taken earlier in the food chain.
8.1 GENERAL
Food must be adequately protected during transport. The type of conveyances or containers
required depends on the nature of the food and the conditions under which it has to be transported.
8.2 REQUIREMENTS
Where necessary, conveyances and bulk containers should be designed and constructed so that
they:
" do not contaminate foods or packaging;
" can be effectively cleaned and, where necessary, disinfected;
" permit effective separation of different foods or foods from non-food items where necessary
during transport;
" provide effective protection from contamination, including dust and fumes;
" can effectively maintain the temperature, humidity, atmosphere and other conditions necessary
to protect food from harmful or undesirable microbial growth and deterioration likely to
render it unsuitable for consumption; and
" allow any necessary temperature, humidity and other conditions to be checked.
8.3 USE AND MAINTENANCE
Conveyances and containers for transporting food should be kept in an appropriate state of
cleanliness, repair and condition. Where the same conveyance or container is used for transporting
different foods, or non-foods, effective cleaning and, where necessary, disinfection should take
place between loads.
CAC/RCP 1-1969, Rev.4- 2003
Page 19 of 31
Where appropriate, particularly in bulk transport, containers and conveyances should be
designated and marked for food use only and be used only for that purpose.
SECTION IX - PRODUCT INFORMATION AND CONSUMER AWARENESS
OBJECTIVES:
Products should bear appropriate information to ensure that:
- adequate and accessible information is available to the next person in the food chain to enable
them to handle, store, process, prepare and display the product safely and correctly;
- the lot or batch can be easily identified and recalled if necessary.
Consumers should have enough knowledge of food hygiene to enable them to:
- understand the importance of product information;
- make informed choices appropriate to the individual; and
- prevent contamination and growth or survival of foodborne pathogens by storing, preparing
and using it correctly.
Information for industry or trade users should be clearly distinguishable from consumer
information, particularly on food labels.
RATIONALE:
Insufficient product information, and/or inadequate knowledge of general food hygiene, can lead
to products being mishandled at later stages in the food chain. Such mishandling can result in
illness, or products becoming unsuitable for consumption, even where adequate hygiene control
measures have been taken earlier in the food chain.
9.1 LOT IDENTIFICATION
Lot identification is essential in product recall and also helps effective stock rotation. Each
container of food should be permanently marked to identify the producer and the lot. Codex
General Standard for the Labelling of Prepackaged Foods (CODEX STAN 1-1985, Rev. 1(1991))
applies.
9.2 PRODUCT INFORMATION
All food products should be accompanied by or bear adequate information to enable the next
person in the food chain to handle, display, store and prepare and use the product safely and
correctly.
9.3 LABELLING
Prepackaged foods should be labelled with clear instructions to enable the next person in the food
chain to handle, display, store and use the product safely. Codex General Standard for the
Labelling of Prepackaged Foods (CODEX STAN 1-1985, Rev. (1991)) applies.
9.4 CONSUMER EDUCATION
Health education programmes should cover general food hygiene. Such programmes should
enable consumers to understand the importance of any product information and to follow any
instructions accompanying products, and make informed choices. In particular consumers should
be informed of the relationship between time/temperature control and foodborne illness.
CAC/RCP 1-1969, Rev.4- 2003
Page 20 of 31
SECTION X - TRAINING
OBJECTIVE:
Those engaged in food operations who come directly or indirectly into contact with food should
be trained, and/or instructed in food hygiene to a level appropriate to the operations they are to
perform.
RATIONALE:
Training is fundamentally important to any food hygiene system.
Inadequate hygiene training, and/or instruction and supervision of all people involved in food
related activities pose a potential threat to the safety of food and its suitability for consumption.
10.1 AWARENESS AND RESPONSIBILITIES
Food hygiene training is fundamentally important. All personnel should be aware of their role
and responsibility in protecting food from contamination or deterioration. Food handlers should
have the necessary knowledge and skills to enable them to handle food hygienically. Those who
handle strong cleaning chemicals or other potentially hazardous chemicals should be instructed in
safe handling techniques.
10.2 TRAINING PROGRAMMES
Factors to take into account in assessing the level of training required include:
" the nature of the food, in particular its ability to sustain growth of pathogenic or spoilage
micro-organisms;
" the manner in which the food is handled and packed, including the probability of
contamination;
" the extent and nature of processing or further preparation before final consumption;
" the conditions under which the food will be stored; and
" the expected length of time before consumption.
10.3 INSTRUCTION AND SUPERVISION
Periodic assessments of the effectiveness of training and instruction programmes should be made,
as well as routine supervision and checks to ensure that procedures are being carried out
effectively.
Managers and supervisors of food processes should have the necessary knowledge of food
hygiene principles and practices to be able to judge potential risks and take the necessary action to
remedy deficiencies.
10.4 REFRESHER TRAINING
Training programmes should be routinely reviewed and updated where necessary. Systems
should be in place to ensure that food handlers remain aware of all procedures necessary to
maintain the safety and suitability of food.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 21
HAZARD ANALYSIS AND CRITICAL CONTROL POINT (HACCP) SYSTEM AND
GUIDELINES FOR ITS APPLICATION
Annex to CAC/RCP 1-1969 (Rev. 4 - 2003)
PREAMBLE
The first section of this document sets out the principles of the Hazard Analysis and Critical Control
Point (HACCP) system adopted by the Codex Alimentarius Commission. The second section provides
general guidance for the application of the system while recognizing that the details of application may
vary depending on the circumstances of the food operation.2
The HACCP system, which is science based and systematic, identifies specific hazards and measures for
their control to ensure the safety of food. HACCP is a tool to assess hazards and establish control
systems that focus on prevention rather than relying mainly on end-product testing. Any HACCP
system is capable of accommodating change, such as advances in equipment design, processing
procedures or technological developments.
HACCP can be applied throughout the food chain from primary production to final consumption and its
implementation should be guided by scientific evidence of risks to human health. As well as enhancing
food safety, implementation of HACCP can provide other significant benefits. In addition, the
application of HACCP systems can aid inspection by regulatory authorities and promote international
trade by increasing confidence in food safety.
The successful application of HACCP requires the full commitment and involvement of management
and the work force. It also requires a multidisciplinary approach; this multidisciplinary approach should
include, when appropriate, expertise in agronomy, veterinary health, production, microbiology,
medicine, public health, food technology, environmental health, chemistry and engineering, according
to the particular study. The application of HACCP is compatible with the implementation of quality
management systems, such as the ISO 9000 series, and is the system of choice in the management of
food safety within such systems.
While the application of HACCP to food safety was considered here, the concept can be applied to other
aspects of food quality.
DEFINITIONS
Control (verb): To take all necessary actions to ensure and maintain compliance with criteria
established in the HACCP plan.
Control (noun): The state wherein correct procedures are being followed and criteria are being met.
Control measure: Any action and activity that can be used to prevent or eliminate a food safety hazard
or reduce it to an acceptable level.
Corrective action: Any action to be taken when the results of monitoring at the CCP indicate a loss of
control.
Critical Control Point (CCP): A step at which control can be applied and is essential to prevent or
eliminate a food safety hazard or reduce it to an acceptable level.
Critical limit: A criterion which separates acceptability from unacceptability.
2
The Principles of the HACCP System set the basis for the requirements for the application of HACCP, while the
Guidelines for the Application provide general guidance for practical application.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 22
Deviation: Failure to meet a critical limit.
Flow diagram: A systematic representation of the sequence of steps or operations used in the
production or manufacture of a particular food item.
HACCP: A system which identifies, evaluates, and controls hazards which are significant for food
safety.
HACCP plan: A document prepared in accordance with the principles of HACCP to ensure control of
hazards which are significant for food safety in the segment of the food chain under consideration.
Hazard: A biological, chemical or physical agent in, or condition of, food with the potential to cause an
adverse health effect.
Hazard analysis: The process of collecting and evaluating information on hazards and conditions
leading to their presence to decide which are significant for food safety and therefore should be
addressed in the HACCP plan.
Monitor: The act of conducting a planned sequence of observations or measurements of control
parameters to assess whether a CCP is under control.
Step: A point, procedure, operation or stage in the food chain including raw materials, from primary
production to final consumption.
Validation: Obtaining evidence that the elements of the HACCP plan are effective.
Verification: The application of methods, procedures, tests and other evaluations, in addition to
monitoring to determine compliance with the HACCP plan.
PRINCIPLES OF THE HACCP SYSTEM
The HACCP system consists of the following seven principles:
PRINCIPLE 1
Conduct a hazard analysis.
PRINCIPLE 2
Determine the Critical Control Points (CCPs).
PRINCIPLE 3
Establish critical limit(s).
PRINCIPLE 4
Establish a system to monitor control of the CCP.
PRINCIPLE 5
Establish the corrective action to be taken when monitoring indicates that a particular CCP is not under
control.
PRINCIPLE 6
Establish procedures for verification to confirm that the HACCP system is working effectively.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 23
PRINCIPLE 7
Establish documentation concerning all procedures and records appropriate to these principles and their
application.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 24
GUIDELINES FOR THE APPLICATION OF THE HACCP SYSTEM
INTRODUCTION
Prior to application of HACCP to any sector of the food chain, that sector should have in place
prerequisite programs such as good hygienic practices according to the Codex General Principles of
Food Hygiene, the appropriate Codex Codes of Practice, and appropriate food safety requirements.
These prerequisite programs to HACCP, including training, should be well established, fully operational
and verified in order to facilitate the successful application and implementation of the HACCP system.
For all types of food business, management awareness and commitment is necessary for implementation
of an effective HACCP system. The effectiveness will also rely upon management and employees
having the appropriate HACCP knowledge and skills.
During hazard identification, evaluation, and subsequent operations in designing and applying HACCP
systems, consideration must be given to the impact of raw materials, ingredients, food manufacturing
practices, role of manufacturing processes to control hazards, likely end-use of the product, categories of
consumers of concern, and epidemiological evidence relative to food safety.
The intent of the HACCP system is to focus control at Critical Control Points (CCPs). Redesign of the
operation should be considered if a hazard which must be controlled is identified but no CCPs are
found.
HACCP should be applied to each specific operation separately. CCPs identified in any given example
in any Codex Code of Hygienic Practice might not be the only ones identified for a specific application
or might be of a different nature. The HACCP application should be reviewed and necessary changes
made when any modification is made in the product, process, or any step.
The application of the HACCP principles should be the responsibility of each individual businesses.
However, it is recognised by governments and businesses that there may be obstacles that hinder the
effective application of the HACCP principles by individual business. This is particularly relevant in
small and/or less developed businesses. While it is recognized that when applying HACCP, flexibility
appropriate to the business is important, all seven principles must be applied in the HACCP system.
This flexibility should take into account the nature and size of the operation, including the human and
financial resources, infrastructure, processes, knowledge and practical constraints.
Small and/or less developed businesses do not always have the resources and the necessary expertise on
site for the development and implementation of an effective HACCP plan. In such situations, expert
advice should be obtained from other sources, which may include: trade and industry associations,
independent experts and regulatory authorities. HACCP literature and especially sector-specific HACCP
guides can be valuable. HACCP guidance developed by experts relevant to the process or type of
operation may provide a useful tool for businesses in designing and implementing the HACCP plan.
Where businesses are using expertly developed HACCP guidance, it is essential that it is specific to the
foods and/or processes under consideration. More detailed information on the obstacles in
implementing HACCP, particularly in reference to SLDBs, and recommendations in resolving these
obstacles, can be found in  Obstacles to the Application of HACCP, Particularly in Small and Less
Developed Businesses, and Approaches to Overcome Them (document in preparation by FAO/WHO).
The efficacy of any HACCP system will nevertheless rely on management and employees having the
appropriate HACCP knowledge and skills, therefore ongoing training is necessary for all levels of
employees and managers, as appropriate.
APPLICATION
The application of HACCP principles consists of the following tasks as identified in the Logic Sequence
for Application of HACCP (Diagram 1).
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 25
1. Assemble HACCP team
The food operation should assure that the appropriate product specific knowledge and expertise is
available for the development of an effective HACCP plan. Optimally, this may be accomplished by
assembling a multidisciplinary team. Where such expertise is not available on site, expert advice should
be obtained from other sources, such as, trade and industry associations, independent experts, regulatory
authorities, HACCP literature and HACCP guidance (including sector-specific HACCP guides). It may
be possible that a well-trained individual with access to such guidance is able to implement HACCP in-
house. The scope of the HACCP plan should be identified. The scope should describe which segment
of the food chain is involved and the general classes of hazards to be addressed (e.g. does it cover all
classes of hazards or only selected classes).
2. Describe product
A full description of the product should be drawn up, including relevant safety information such as:
composition, physical/chemical structure (including Aw, pH, etc), microcidal/static treatments (heat-
treatment, freezing, brining, smoking, etc), packaging, durability and storage conditions and method of
distribution. Within businesses with multiple products, for example, catering operations, it may be
effective to group products with similar characteristics or processing steps, for the purpose of
development of the HACCP plan.
3. Identify intended use
The intended use should be based on the expected uses of the product by the end user or consumer. In
specific cases, vulnerable groups of the population, e.g. institutional feeding, may have to be considered.
4. Construct flow diagram
The flow diagram should be constructed by the HACCP team (see also paragraph 1 above). The flow
diagram should cover all steps in the operation for a specific product. The same flow diagram may be
used for a number of products that are manufactured using similar processing steps. When applying
HACCP to a given operation, consideration should be given to steps preceding and following the
specified operation.
5. On-site confirmation of flow diagram
Steps must be taken to confirm the processing operation against the flow diagram during all stages and
hours of operation and amend the flow diagram where appropriate. The confirmation of the flow
diagram should be performed by a person or persons with sufficient knowledge of the processing
operation.
6. List all potential hazards associated with each step, conduct a hazard analysis, and consider
any measures to control identified hazards
(SEE PRINCIPLE 1)
The HACCP team (see  assemble HACCP team above) should list all of the hazards that may be
reasonably expected to occur at each step according to the scope from primary production, processing,
manufacture, and distribution until the point of consumption.
The HACCP team (see  assemble HACCP team ) should next conduct a hazard analysis to identify for
the HACCP plan, which hazards are of such a nature that their elimination or reduction to acceptable
levels is essential to the production of a safe food.
In conducting the hazard analysis, wherever possible the following should be included:
" the likely occurrence of hazards and severity of their adverse health effects;
" the qualitative and/or quantitative evaluation of the presence of hazards;
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 26
" survival or multiplication of micro-organisms of concern;
" production or persistence in foods of toxins, chemicals or physical agents; and,
" conditions leading to the above.
Consideration should be given to what control measures, if any exist, can be applied to each hazard.
More than one control measure may be required to control a specific hazard(s) and more than one
hazard may be controlled by a specified control measure.
7. Determine Critical Control Points
(SEE PRINCIPLE 2)3
There may be more than one CCP at which control is applied to address the same hazard. The
determination of a CCP in the HACCP system can be facilitated by the application of a decision tree
(e.g., Diagram 2), which indicates a logic reasoning approach. Application of a decision tree should be
flexible, given whether the operation is for production, slaughter, processing, storage, distribution or
other. It should be used for guidance when determining CCPs. This example of a decision tree may not
be applicable to all situations. Other approaches may be used. Training in the application of the
decision tree is recommended.
If a hazard has been identified at a step where control is necessary for safety, and no control measure
exists at that step, or any other, then the product or process should be modified at that step, or at any
earlier or later stage, to include a control measure.
8. Establish critical limits for each CCP
(SEE PRINCIPLE 3)
Critical limits must be specified and validated for each Critical Control Point. In some cases more than
one critical limit will be elaborated at a particular step. Criteria often used include measurements of
temperature, time, moisture level, pH, Aw, available chlorine, and sensory parameters such as visual
appearance and texture.
Where HACCP guidance developed by experts has been used to establish the critical limits, care should
be taken to ensure that these limits fully apply to the specific operation, product or groups of products
under consideration. These critical limits should be measurable.
9. Establish a monitoring system for each CCP
(SEE PRINCIPLE 4)
Monitoring is the scheduled measurement or observation of a CCP relative to its critical limits. The
monitoring procedures must be able to detect loss of control at the CCP. Further, monitoring should
ideally provide this information in time to make adjustments to ensure control of the process to prevent
violating the critical limits. Where possible, process adjustments should be made when monitoring
results indicate a trend towards loss of control at a CCP. The adjustments should be taken before a
deviation occurs. Data derived from monitoring must be evaluated by a designated person with
knowledge and authority to carry out corrective actions when indicated. If monitoring is not
continuous, then the amount or frequency of monitoring must be sufficient to guarantee the CCP is in
3
Since the publication of the decision tree by Codex, its use has been implemented many times for training purposes. In many
instances, while this tree has been useful to explain the logic and depth of understanding needed to determine CCPs, it is not specific
to all food operations, e.g., slaughter, and therefore it should be used in conjunction with professional judgement, and modified in
some cases.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 27
control. Most monitoring procedures for CCPs will need to be done rapidly because they relate to on-
line processes and there will not be time for lengthy analytical testing. Physical and chemical
measurements are often preferred to microbiological testing because they may be done rapidly and can
often indicate the microbiological control of the product.
All records and documents associated with monitoring CCPs must be signed by the person(s) doing the
monitoring and by a responsible reviewing official(s) of the company.
10. Establish corrective actions
(SEE PRINCIPLE 5)
Specific corrective actions must be developed for each CCP in the HACCP system in order to deal with
deviations when they occur.
The actions must ensure that the CCP has been brought under control. Actions taken must also include
proper disposition of the affected product. Deviation and product disposition procedures must be
documented in the HACCP record keeping.
11. Establish verification procedures
(SEE PRINCIPLE 6)
Establish procedures for verification. Verification and auditing methods, procedures and tests,
including random sampling and analysis, can be used to determine if the HACCP system is working
correctly. The frequency of verification should be sufficient to confirm that the HACCP system is
working effectively.
Verification should be carried out by someone other than the person who is responsible for performing
the monitoring and corrective actions. Where certain verification activities cannot be performed in
house, verification should be performed on behalf of the business by external experts or qualified third
parties.
Examples of verification activities include:
" Review of the HACCP system and plan and its records;
" Review of deviations and product dispositions;
" Confirmation that CCPs are kept under control.
Where possible, validation activities should include actions to confirm the efficacy of all elements of the
HACCP system.
12. Establish Documentation and Record Keeping
(SEE PRINCIPLE 7)
Efficient and accurate record keeping is essential to the application of a HACCP system. HACCP
procedures should be documented. Documentation and record keeping should be appropriate to the
nature and size of the operation and sufficient to assist the business to verify that the HACCP controls
are in place and being maintained. Expertly developed HACCP guidance materials (e.g. sector-specific
HACCP guides) may be utilised as part of the documentation, provided that those materials reflect the
specific food operations of the business.
Documentation examples are:
Hazard analysis;
CCP determination;
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 28
Critical limit determination.
Record examples are:
" CCP monitoring activities;
" Deviations and associated corrective actions;
" Verification procedures performed;
" Modifications to the HACCP plan;
An example of a HACCP worksheet for the development of a HACCP plan is attached as Diagram 3.
A simple record-keeping system can be effective and easily communicated to employees. It may be
integrated into existing operations and may use existing paperwork, such as delivery invoices and
checklists to record, for example, product temperatures.
TRAINING
Training of personnel in industry, government and academia in HACCP principles and applications and
increasing awareness of consumers are essential elements for the effective implementation of HACCP.
As an aid in developing specific training to support a HACCP plan, working instructions and procedures
should be developed which define the tasks of the operating personnel to be stationed at each Critical
Control Point.
Cooperation between primary producer, industry, trade groups, consumer organisations, and responsible
authorities is of vital important. Opportunities should be provided for the joint training of industry and
control authorities to encourage and maintain a continuous dialogue and create a climate of
understanding in the practical application of HACCP.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 29
DIAGRAM 1
LOGIC SEQUENCE FOR APPLICATION OF HACCP
Assemble HACCP Team
1.
Describe Product
2.
Identify Intended Use
3.
Construct Flow Diagram
4.
On-site Confirmation of Flow Diagram
5.
List all Potential Hazards
6.
Conduct a Hazard Analysis
Consider Control Measures
Determine CCPs
7.
See Diagram 2
Establish Critical Limits for each CCP
8.
Establish a Monitoring System for each CCP
9.
Establish Corrective Actions
10.
Establish Verification Procedures
11.
Establish Documentation and Record Keeping
12.
CAC/RCP 1-1969, Rev. 4-2003 - Annex Page 30
DIAGRAM 2
EXAMPLE OF DECISION TREE TO IDENTIFY CCPs
(answer questions in sequence)
Do control preventative measure(s) exist?
Q1
Modify step, process
Yes No
or product
Is control at this step
Yes
necessary for safety?
Not a CCP Stop (*)
No
Is the step specifically designed to
eliminate or reduce the likely occurrence of
Yes
Q2
a hazard to an acceptable level? (**)
No
Could contamination with identified hazard(s)
occur in excess of acceptable level(s) or could
Q3
these increase to unacceptable levels? (**)
Not a CCP Stop (*)
Yes No
Will a subsequent step eliminate identified
hazard(s) or reduce likely occurrence to an
Q4
acceptable level? (**)
CRITICAL CONTROL POINT
Yes No
Not a CCP Stop (*)
(*)
Proceed to the next identified hazard in the described process.
(**)
Acceptable and unacceptable levels need to be defined within the overall objectives in identifying the CCPs of HACCP
plan.
CAC/RCP Page 31 of 31
DIAGRAM 3
EXAMPLE OF A HACCP WORKSHEET
Describe Product
1.
Diagram Process Flow
2.
LIST
3.
Step Hazard(s Control CCPs Critical Monitoring Corrective Record(s)
)
Measure(s) Limit(s) Procedure(s) Action(s)
Verification
4.


Wyszukiwarka

Podobne podstrony:
codex alimentarius kodeks zywnosciowy samobojstwo zachodniego swiata eioba
01 Fritz ter Meer współtwórca Codex Alimentaris
Czym jest Codex Alimentarius 2
Codex Alimentarius
CODEX ALIMENTARIUS SAMOBÓJSTWO ZACHODNIEGO ŚWIATA
03 Wiesz czym jest Codex Alimentarius
Codex Alimentarius
Rozwod alimenty separacja
konwencja doch roszcz aliment za granica
w sprawie wzoru wniosku o ustalenie prawa do zaliczki alimentacyjnej oraz odpowiednich zaświadczeń
Arcanis Codex Arcanis Compendium
pozew o alimenty wzór z instrukcjami
Alimentazione1
Pozew o podwyższenie alimentów

więcej podobnych podstron