05 11 F01 Exterior Rear View Mirrors


Table of Contents
F01 Exterior Rear View Mirrors
Subject Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Input/output - Outside Mmirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
System Circuit Diagram - Outside Mirror High . . . . . . . . . . . . . . . . . . . . .6
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mirror Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Outside mirror adjustment High . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Detecting position of outside mirrors . . . . . . . . . . . . . . . . . . . . . .10
Mirror Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Outside mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Terminal 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Mirror Fold-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Electrochromic Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Outside Mirror with Memory Function . . . . . . . . . . . . . . . . . . . . . . . . .12
Identification transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Storing memory position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Calling up memory position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Automatic Parking Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Folding Mirror Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Motor Protection by Repeat Interlock . . . . . . . . . . . . . . . . . . . . . . . . .13
Mirror Auto Remote Fold-in Function (Comfort Function) . . . . . . .13
System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Driver s Door Switch Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Design of the Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Drive unit with memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Footwell Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Junction Box Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Initial Print Date: 01/09 Revision Date:
Exterior Rear View Mirrors
Model: F01/F02
Production: From Start of Production
After completion of this module you will be able to:
" Understand the operation of the exterior rear view mirrors on the F01/F02
2
F01 Exterior Rear View Mirrors
Introduction
Outside Mirrors
For the F01/F02, there is only one variant of the outside mirrors. The outside mirrors can
be electrically adjusted as standard. The outside mirrors are equipped with a mirror heat-
ing system.
Optional Interior and exterior mirrors with automatic anti-dazzle function (electrochromic)
can be ordered as an optional extra. This option requires the interior rear-view mirror with
automatic anti-dazzle function.
The outside mirrors with memory function are connected via the LIN-bus and additional-
ly feature the following functions:
" Outside mirror fold-in
" Electrochromic outside mirrors
" Electrical seat adjustment with memory
3
F01 Exterior Rear View Mirrors
System Overview
Input/output - Outside Mmirrors
Index Explanation Index Explanation
1 Instrument cluster 5 Outside mirror, passenger's side
Mirror adjustment switch in driver's
2 Footwell module FRM 6
door switch cluster SBFA
3 Outside temperature sensor 7 Outside mirror, driver's side
4 Junction box electronics JB K-CAN2 Body CAN 2
4
F01 Exterior Rear View Mirrors
Instrument cluster (1) records the outside temperature and makes this information avail-
able to the vehicle electrical system.
Junction box electronics (4) supply the outside mirror heating. The outside mirrors (5 + 6)
can be adjusted with the mirror adjustment switch in the driver s door switch cluster (6).
5
F01 Exterior Rear View Mirrors
System Circuit Diagram - Outside Mirror High
6
F01 Exterior Rear View Mirrors
Index Explanation Index Explanation
Electrochromic outside mirror,
1 Central gateway module (ZGM) 14
driver's side
Memory, outside mirror potentiometer,
2 Car Access System (CAS) 15
driver s side
Motor for folding mirror function,
3 Outside temperature sensor 16
driver s side
Outside mirror heating,
4 Junction box electronics (JB) 17
driver s side
5 Outside mirror heating, passenger s side 18 Footwell module (FRM)
Motor for folding mirror function,
6 19 Instrument cluster
passenger s side
Memory, outside mirror potentiometer,
7 20 Front distribution box
passenger s side
Electrochromic outside mirror,
8 LIN-Bus Local Interconnect Network bus
passenger s side
Actuator motor for passenger s side
9 Kl. 30B Terminal 30 basic operation
outside mirror
Driver s door switch cluster (SBFA)
10 Kl. 58g Terminal 58g
with mirror selector switch
Driver s door switch cluster (SBFA)
11 K-CAN2 Body CAN2
with mirror adjustment switch
12 Driver s door switch cluster (SBFA) PT-CAN Powertrain CAN with mirror folding switch
13 Actuator motor for driver's outside mirror
7
F01 Exterior Rear View Mirrors
K-CAN2 signals at footwell module
In/out Information Source/sink Function
Wheel speed sensor >
In Vehicle speed Mirror fold-in lock (inhibit)
Dynamic Stability Control
Status, electrochromic interior Photodiode, rear-view mirror >
In Dip outside mirror
rear-view mirror roof function center
The instrument cluster (19) receives the value corresponding to the outside temperature
from the outside temperature sensor (3) and makes it available via the PT-CAN. The
footwell module (18) evaluates the K-CAN2 signal and initiates activation of the outside
mirror heating (5 and 17).
The mirror adjustment motors (9 and 13) are driven by the electronic mirror module. The
electronic mirror module receives the request to adjust the outside mirrors via the LIN-
bus.
The outside mirrors are connected via the LIN-bus. All information such as the memory-
position or mirror functions, e.g. dip outside mirrors, is transferred via the LIN-bus.
8
F01 Exterior Rear View Mirrors
NOTES
PAGE
9
F01 Exterior Rear View Mirrors
Functions
Overview
The following outside mirror functions are possible depending on the vehicle equipment:
" Mirror adjustment in up/down and left/right directions
" Mirror heating
" Mirror fold-in
" Electrochromic mirror, outside mirror with memory function
" Automatic parking function
" Manual adjustment
" Motor protection by repeat interlock
Mirror Adjustment
Outside mirror adjustment High
The driver s door switch cluster is connected via the LIN-bus to the footwell module.
The footwell module checks the status of the mirror adjustment switch every 20 ms. The
electronics in the driver s door switch cluster evaluates the mirror adjustment switch and
sends the signal via the LIN-bus to the footwell module. In turn, the footwell module initi-
ates activation of the adjustment motors.
To protect the mirror drive unit, the mirror adjustment is limited to a maximum activation
time of 10 seconds. Activation is maintained within this period of 10 seconds until the
mirror adjustment switch is released.
Activation is also maintained until the outside mirror blocks or reaches its end position.
Detecting position of outside mirrors
The High version of the outside mirrors has two potentiometers that register the mirror
adjustment. The potentiometers receive their 5V voltage supply from the electronic mir-
ror module. The determined values of the potentiometers are stored in the footwell mod-
ule for the memory function.
Mirror Heating
The mirror heating is operable as from terminal 15 ON.
Outside mirror
The mirror heating is activated by the footwell module. The corresponding information is
passed on to the electronic mirror module via the LIN-bus.
The instrument cluster makes available the outside temperature value via the PT-CAN.
The signal is transferred to the K-CAN2 by the central gateway module.
10
F01 Exterior Rear View Mirrors
The junction box electronics provide the information for the wipers via the K-CAN2.
The percentage switch-on time is calculated from both values in the footwell module.
The following table shows the values for the percentage ON time:
Temperature in °C < -10 -10 to 5 5 to 15 15 to 25 25 to 35 > 35
Heating capacity in % 100 75 50 0 0 0
Heating capacity with wipers ON in % 100 100 75 50 25 0
The percentage increase is still retained for 300 seconds after the wiper is switched off.
The maximum electric heating output is 28 W that is set by means of voltage and current
measurement in the mirror.
Undervoltage
The electronic mirror module switches off the mirror heating in the event of undervoltage.
This has a positive effect on the charge balance of the battery. The cutout threshold is at
10.8 V.
The electronic mirror module switches on the mirror heating again as from a voltage of
11.6 V.
Terminal 50
The  terminal 50 ON status is output during the starting procedure. The mirror heating
is switched off for the duration.
Mirror Fold-in
The mirror fold-in function is controlled by the footwell module. For this purpose, the
footwell module requests the status of the mirror fold-in switch. The driver s switch clus-
ter evaluates the mirror fold-in switch and forwards the request via the LIN-bus. The
footwell module initiates the fold-in function.
The electronic mirror module receives the request and executes this function by activat-
ing the corresponding fold-in motor. The footwell module receives the request via the
LIN-bus. Both outside mirrors are folded in towards the vehicle thus reducing the vehicle
width.
11
F01 Exterior Rear View Mirrors
Electrochromic Outside Mirrors
The automatic dip function (anti-dazzle) of the outside mirrors is dependent on the set-
ting of the interior rear-view mirror. The function is available as from  terminal 15 ON .
The interior rear-view mirror forwards the anti-dazzle request to the junction box electron-
ics on the LIN-bus. The junction box electronics transfer the request to the K-CAN. The
footwell module is now able to receive the request.
The footwell module sends this request via the LIN-bus to the electronics in the outside
mirrors. The electronics implement the request to dim the outside mirrors.
Outside Mirror with Memory Function
The outside mirror High features a memory function that is stored in the footwell module.
Three memory locations are available for this purpose. They are:
" Current position when leaving the vehicle
" Memory position of memory button 1
" Memory position of memory button 2.
Identification transmitter
Up to three personalizable ID transmitters are possible per vehicle.
When the vehicle is locked using the ID transmitter, the current mirror position is stored in
the memory location for the key memory of the ID transmitter currently used.
As a result, the mirror position last set, referred to the ID transmitter used, is always reas-
sumed when the vehicle is unlocked.
Storing memory position
The position of the outside mirrors is stored in the footwell module by pressing the  M
button followed by pressing one of the memory buttons within 7 seconds.
The footwell module evaluates signals from the memory buttons on the LIN-bus and
transmits this information on the K-CAN2. As a result, the seat module also knows when
to store the current seat position.
Calling up memory position
When the memory button is pressed, the footwell module receives the request to adjust
the outside mirrors to the memory position. The footwell module sends the request to
the K-CAN2. The seat module is therefore aware of the request and instructs the seat to
move to the memory position.
12
F01 Exterior Rear View Mirrors
Automatic Parking Function
The outside mirror on the front passenger s side is swivelled downward when reverse
gear is engaged so that the kerb can be easily viewed.
The automatic parking function is activated under following conditions:
" Terminal 15 ON and
" Reverse gear signal and
" Mirror selector switch set to driver position.
The footwell module receives the reverse gear signal via the K-CAN2. The automatic
transmission control unit then makes this signal available.
Folding Mirror Manually
The outside mirrors can be folded in or out manually. The outside mirrors could lose their
set position when folded in or out manually. It may be therefore necessary to fold out the
outside mirrors, fold them in and then fold them out again.
The outside mirrors will then again be in the correct locked position.
Motor Protection by Repeat Interlock
The outside mirrors feature a repeat inhibit facility to avoid thermal overheating by fre-
quently folding the mirrors in and out. The motors cannot be activated for 180 seconds
when the repeat inhibit is active.
Mirror Auto Remote Fold-in Function (Comfort Function)
The auto remote fold-in function for the outside mirrors can be activated through follow-
ing components:
" Identification transmitter
" Driver s door lock cylinder
" Outer door handle.
For example, the  Lock button on the ID transmitter must be pressed for longer than
5 seconds to trigger the fold-in function. Fold-in is then initiated. Initially, the panoramic
glass roof is closed, followed after a time delay by the front/rear windows.
With the option  Fold-in outside mirrors The outside mirrors are folded in simultaneously
with closing the rear windows.
13
F01 Exterior Rear View Mirrors
System Components
Overview
The following components are installed in the F01/F02 for the purpose of operating the
outside mirrors:
" Driver s door switch cluster with
 Outside mirror adjustment switch
 Outside mirror selector switch
 LIN-bus link
" Outside mirrors
" Footwell module
" Junction box electronics
" Components for comfort/convenience function
 Car Access System
 Driver s door lock cylinder
 Remote control receiver in the diversity module.
Driver s Door Switch Cluster
The driver s door switch cluster is connected via the LIN-bus to the footwell module.
The adjustment motors in the Low version of the outside mirrors are controlled directly
by the mirror adjustment switch in the driver s door switch cluster.
The driver s door switch cluster in the High version of the outside mirrors is connected
to the outside mirrors via the LIN-bus.
The electronic mirror module in the outside mirrors evaluates the LIN-bus signals and
activates the adjustment motors.
Note: The driver s door switch cluster is connected to terminal 30B, terminal
31. The driver s door switch cluster receives the status of terminal 58g
from the footwell module on the LIN-bus.
14
F01 Exterior Rear View Mirrors
Design of the Outside Mirrors
Drive unit with memory
The drive unit with memory function additionally consists of the following components:
" Electronic mirror module
" Position potentiometer
" Folding mirror motor
" LIN-bus
" Electrochromic glass.
Note: In combination with the Active Blind Spot Detection (Lane Change
Warning) the outside mirror also contains the display for the warning.
Footwell Module
The master function for controlling the outside mirrors is integrated in the footwell mod-
ule.
On vehicles with memory function, the mirror position of the respective memory button
(driver s seat) is stored in the footwell module.
The outside mirrors (high) and the driver s door switch cluster are connected to the
footwell module via the LIN-bus. The outside mirror functions are activated via the LIN-
bus.
Junction Box Electronics
The junction box electronics power the low version of the outside mirror heating system.
The signal is pulse width-modulated and has a frequency of 1 Hz.
The junction box electronics also request the status of the electrochromic interior rear-
view mirror on the LIN-bus. The mirror electronics feed back the current status of the
electrochromic interior rear-view mirror. The junction box electronics send the status to
the footwell module on the K-CAN2. The footwell module is therefore aware of the status
and is able to control the dimming of the outside mirrors accordingly.
15
F01 Exterior Rear View Mirrors


Wyszukiwarka