Technical Description
Specification of KEY for CI Plus, DTCP-IP, One-to-One, Widevine and Netflix
General information:
1. EEPROM (IC8902) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by PRO4 IC (IC8000) when SELF CHECK was done and are stored in both PRO4 IC
(IC8000) and EEPROM (IC8902).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
Replacement of ICs:
When PRO4 IC (IC8000) is replaced, EEPROM (IC8902) should be also replaced with new one the same time.
When EEPROM (IC8902) is replaced, PRO4 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the STATUS button on the remote
control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
Models and Keys:
Keys
Model No. One-to-One
CI PLUS DTCP-IP Widevine Netflix
(for USB Rec.)
TX-L55WT50E Yes Yes Yes Yes Yes
TX-L55WT50T Yes Yes Yes Yes Yes
USB HDD Recording:
General information:
Digital TV programmes can be recorded in USB HDD.
A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
That key is only one key for them. If the key is difference, TV can not access USB-HDD.
Caution:
New key will be generated by following SELF CHECK and previous TV programmes recorded in USB HDD will not be
viewed.
SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the STATUS button on the remote control
for more than 3 seconds
11
Setting Inspection
Voltage Confirmation
A board
Description Test point Voltage
SUB1.1V TP8100 1.10V - 1.22V
SUB 1.5 V TP8101 1.435V - 1.585V
SUB1.8V TP8700 1.7V  1.9V
SUB3.3V TP5400 3.17V  3.43V
SUB5V TP5420 4.80V - 5.25V
USB5V TP5440 4.94V  5.40V
FE1.2V TP5780 1.14V  1.26V
FE1.2V/2.5V TP5720 2.375V  2.625V
PNL12V TP4004 (TP4005) 11.5V  12.9V
Horizontal 17.0V - 19.0V
LNB_OUTPUT TP6702
Vertical 12.5V  14.0V
12
Self Check
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep
pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check,
switch off the TV set at the power button.
TX-L55WT50E
55FHD Panasonic 2012LCD
Self Check Complete
SUM C15D
TUN O.K. PEAKS-SOFT 1.619
STBY O.K. PEAKS-EEP 01.06.0011
MEM1 O.K. LSI-PACKAGE 0.016
MODEL ID 09
MEM2 O.K. LSI-RELEASE 1.14
03012100
AVSW O.K. STBY-SOFT 1.00.02
00040000
LAN O.K. STBY-EEP 1.00.0015
ZWEI O.K. STBY-ROMCORR 0.00.00
SAT-TU O.K. ZWEI-SOFT 09010011
ID O.K.
ID2 O.K.
BT O.K.
WiFi O.K.
TX-L55WT50T
55FHD Panasonic 2012LCD
Self Check Complete
SUM C178
TUN O.K. PEAKS-SOFT 1.619
STBY O.K. PEAKS-EEP 01.06.0027
MEM1 O.K. LSI-PACKAGE 0.016
MODEL ID 09
MEM2 O.K. LSI-RELEASE 1.14
03042300
AVSW O.K. STBY-SOFT 1.00.02
00040000
LAN O.K. STBY-EEP 1.00.0015
ZWEI O.K. STBY-ROMCORR 0.00.00
SAT-TU O.K. ZWEI-SOFT 09010011
ID O.K.
ID2 O.K.
BT O.K.
WiFi O.K.
Display Ref. No. Description P.C.B.
TUN TU6702 TUNER A-Board
STBY IC8000 Peaks-PRO4 A-Board
MEM1 IC8900 NAND FLASH MEMORY A-Board
MEM2 IC8902 EEPROM PEAKS PRO4 A-Board
AVSW IC3001 AUDIO/VIDEO SWITCH A-Board
LAN IC8600 LAN CONTROLER A-Board
ZWEI TC-unit TC-unit on panel TC-unit
SAT-TU TU6702 TUNER A-Board
ID IC8902 CI+, DTCP-IP, C2mod A-Board
ID2 IC8902 WIDEVINE , NETLFLIX A-Board
IC8458 USB HUB A-Board
BT
N5HZZ0000113 BT DONGLE BT Dongle
IC8458 USB HUB A-Board
WiFi
N5HBZ0000067 WIFI DONGLE Wifi Dongle
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
13
Power LED blinking timing chart
1. Subject
Information of LED Flashing timing chart.
2. Contents
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
Blinking
Blinking timing Contents Check point
times
Once
4 sec
Light
A BOARD
1 BL_SOS
P BOARD
No Light
3 IROM SOS A BOARD
7 SUB3.3V_SENSE_SOS A BOARD
8 SOS A BOARD
9 SOUND_SOS A BOARD
10 ZWEI_SOS TC-unit on panel
12 BE_SOS A BOARD
13 EMERGENCY A BOARD
14
Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can
be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
0
Note:
To exit from Service mode, press the exit button on remote control.
15
SERVICE
SERVICE Peaks SOFT 1.619 OPTION 1 34
ADJUST Peaks EEP 01.06.0027 OPTION 2 ee
S e r v i c e 1
Key Command
WB-ADJ LSI PACKAGE 0.016 OPTION 3 01
OPTION LSI DATA 1.01.04 OPTION 4 53
SRV-TOOL STBY SOFT 1.00.02 MODEL ID 09
·ð Press the 3/4 button to change the adjustment values or function.
DRV CHECK STBY EEP 0.08.0015 03012100
STBY ROMCOR 0.00.00 00040000 ·ð Press the 1/2 button to step up/down through the functions and adjustments
ZWEI SOFT 7.100.0008 R/E Cnt 000/000
·ð Press the numerical button VOLUME (+/-) to change of each option item.
AJAX-CE 0.47.5 INV Cnt 0000
·ð Press the OK button after each adjustment has been made to store the required values.
AVSW re
1 2
216
ADJUST DYNAMIC ADJUST DYNAMIC ADJUST DYNAMIC ADJUST DYNAMIC ADJUST DYNAMIC ADJUST DYNAMIC
ADJUST DYNAMIC ADJUST DYNAMIC ADJUST DYNAMIC
3
3
CONTRAST 3 3 SUB-BRT BACKLGT 3 H-POS H-AMP V-POS V-AMP
COLOR TINT 800
000 200 0 3 0 3 0
50 00 0 3
YMAX
1,2:MAIN SELECT 1,2:MAIN SELECT
1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT
4 4 4
4 4 4 4 4
3,4:SUB SELECT 3,4:SUB SELECT
3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT
9:PICTURE MENU SELECT 9:PICTURE MENU SELECT
9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT
VOL :ADJUST VOL :ADJUST
YELLOW:AUTO ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST
OK :WRITE OK :WRITE
VOL :ADJUST OK :WRITE OK :WRITE OK :WRITE OK :WRITE OK :WRITE OK :WRITE
OK :WRITE
3
4
1 2
ADJUST DYNAMIC
VCOM
193
WB-ADJ DYNAMIC WB-ADJ DYNAMIC WB-ADJ DYNAMIC WB-ADJ DYNAMIC WB-ADJ DYNAMIC WB-ADJ DYNAMIC
R-GAIN G-GAIN B-GAIN R-CENT G-CENT B-CENT BEFORE 193
79 80
80 85 95
77
3
3 3 3 3
BEFORE 79 BEFORE 77 BEFORE 80 BEFORE 85 BEFORE 80 BEFORE 95
METHOD 02 METHOD 02 METHOD 02 METHOD 02 METHOD 02 METHOD 02
COLOR TEMP NORMAL COLOR TEMP NORMAL COLOR TEMP NORMAL COLOR TEMP NORMAL COLOR TEMP NORMAL COLOR TEMP NORMAL
1,2:MAIN SELECT
3,4:SUB SELECT
1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT
5 :FLICKER PATTERN
3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT
9 :PICTURE MENU SELECT
4 4
4 4 4
7:COLOR TEMP SELECT 7:COLOR TEMP SELECT 7:COLOR TEMP SELECT 7:COLOR TEMP SELECT 7:COLOR TEMP SELECT 7:COLOR TEMP SELECT
OK :WRITE
9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT
VOL :ADJUST
0:WB METHOD SELECT 0:WB METHOD SELECT 0:WB METHOD SELECT 0:WB METHOD SELECT 0:WB METHOD SELECT 0:WB METHOD SELECT
VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST VOL :ADJUST
OK :WRITE/WB DIFF ADJ OK :WRITE/WB DIFF ADJ OK :WRITE/WB DIFF ADJ OK :WRITE/WB DIFF ADJ OK :WRITE/WB DIFF ADJ OK :WRITE/WB DIFF ADJ
1 2
OPTION DYNAMIC
OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC OPTION DYNAMIC
CLOCK 3
Boot STBY-SET CLK MODE 3 ON 3 3 3
Emergency Y/C Delay OPT 1 OPT 2 OPT 3 00000001
00110100
SD 3 3 O0 ON 11101110
00 3
1,2:MAIN SELECT 4
1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT 1,2:MAIN SELECT
4 4 4
4 4
4 4
3,4:SUB SELECT
3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT 3,4:SUB SELECT
9 :PICTURE MENU SELECT
9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9 :PICTURE MENU SELECT 9 :PICTURE MENU SELECT 9:PICTURE MENU SELECT 5,6:BIT SELECT 5,6:BIT SELECT 5,6:BIT SELECT
VOL:ADJUST
VOL :ADJUST OK :POWER OFF VOL:ADJUST VOL:ADJUST VOL :ADJUST 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT 9:PICTURE MENU SELECT
OK :WRITE VOL :ADJUST VOL :ADJUST VOL :ADJUST
OK :WRITE OK :WRITE OK :WRITE
1 2
3
4
SRV-TOOL DYNAMIC
00
OPTION DYNAMIC OPTION DYNAMIC
EDID-CLK MID OPT 4
3 01010011
HDMI 1
1,2:MAIN SELECT
9:PICTURE MENU SELECT
OK:ENTER
1,2:MAIN SELECT 1,2:MAIN SELECT
4
1 2
3,4:SUB SELECT 3,4:SUB SELECT
7 :HDMI SELECT 5,6:BIT SELECT
9 :PICTURE MENU SELECT 9:PICTURE MENU SELECT
DRV-CHECK DYNAMIC
OK:WRITE VOL :ADJUST
USBHDD CHECK
00
OK :WRITE
1,2:MAIN SELECT
9:PICTURE MENU SELECT
OK 3sec:HDD CHK START
16
Service Tool Mode
How to access
1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.
SRV-TOOL
Display of TD2Microcode version
TD2Microcode:005a0910
Display of Flash ROM maker code Flash ROOM: AD  F1
POWER ON TIME/COUNT
Display of SOS History PTCT:00.00.00.00.00 Time 00051:30 On/Off 0000042
Press [MUTE] button (3sec)
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication will be cleared by [Self/check indication and forced to factory shipment setting].
Power ON Time, On/Off
Note: To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time: Cumulative power on time, indicated hour: minute by decimal.
On/Off: Number of On/Off switching by decimal.
Note: This indication will not be cleared by either of the self-checks or any other command.
Exit
Disconnect the AC cord from wall outlet or switch off the power with [Power] button on the main unit.
17
Hotel Mode
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu.
In order to display the Hotel mode setup menu,
please enter the following command (within 2 second).
[TV] : Vol.[Down] + [REMOTE] : AV (3 times)
Then, the Hotel mode setup menu is displayed.
ITEM Function
Hotel mode
Hotel Mode Select hotel mode ON/OFF
Hotel mode Off Initial INPUT Select input signal modes.
Set the input, when each time power is switched on.
Selection:
Initial INPUT Off
Off/Analog /DVB-S/DVB-C/DVB-T/AV1/AV2/PC/
HDMI1/HDMI2/HDMI3/HDMI4
Initial POS Off
*Off: give priority to the last memory. However, Euro
Model is compulsorily set to TV.
*AVnS/AVnC: only Euro model selectable
Initial VOL Level Off
* PC:selectable with VGA option
Initial POS Select programme number.
Maximum VOL Level 100
Selection:
Off/0 to 99
*Off: give priority to the last memory
Button Lock Off
Initial VOL Level Adjust the volume when each time power is
switched on.
Remote Lock Off
Selection/Range:
Off/0 to 100
*Off: give priority to the last memory
Private Information Keep
Maximum VOL Adjust maximum volume.
Level Range:
0 to 100
Select Button Lock Select local key conditions.
OK
EXIT Selection:
Off/SETUP/MENU/ALL
*Off: altogether valid
RETURN
*Setup: only F-key is invalid
(Tuning guide (menu) can not be selected.)
*MENU: only F-key is invalid
(only Volume/Mute can be selected.)
*All: altogether invalid.
3. To exit the  Hotel mode menu press the EXIT
Remote Lock Select remote control key conditions.
button on remote control.
Selected
4. Explain the Hotel mode setup menu.
Off/SETUP/MENU
*Off: altogether valid
*Setup: only Setup menu is invalid
MENU: Picture/Sound/Setup menu are invalid
Private Select private information for VIERA Cast is Keep or
Information Reset if Hotel mode is set to [On] when TV power
on.
Selection :
Keep/Reset
" Keep: private information for VIERA Cast is keep
" Reset: private information for VIERA Cast is reset
18
Data Copy by SD Card
Purpose
a) Board replacement (Copy the data when exchanging A-board):
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
TV
Following data can be copied.
(Before exchanging)
User setting data
Copy to SD card
(inc. Hotel mode setting data)
Channel scan data
A-board
SD
Adjustment and factory preset data
(After exchanging)
Copy back from SD card
b) Hotel (Copy the data when installing a number of units in hotel or any facility):
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and the copy
to other TVs.
Following data can be copied.
Other TV
Master TV Other TV Other TV User setting data
(inc. Hotel mode setting data)
Channel scan data
SD
Copy to SD card
Copy from SD card
Preparation
Make pwd file as startup file for (a) or (b) in an empty SD card.
1. Insert an empty SD card to your PC.
2. Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by
default (New Text Document.txt).
3. Right-click the new text document that you just created and select rename, and then change the name and extension
of the file to the following file name (a) or (b) and press ENTER.
File name:
(a) For Board replacement: boardreplace.pwd
(b) For Hotel: hotel.pwd
Note:
Please make only one file to prevent the operation error.
No any other file should be in SD card.
19
Data Copy from TV set to SD Card
1. Turn on the TV set.
2. Insert SD card with a startup file (pwd file) to SD slot.
On-screen Display will be appeared according to the startup file automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2770
(b) For Hotel: 4850
Data will be copied from TV set to SD card.
It takes around 2 to 6 minutes maximum for copying.
4. After the completion of copying to SD card, remove SD card from TV set.
5. Turn off the TV set.
Note:
Following new folder will be created in SD card for data from TV set.
(a) For Board replacement: user_setup
(b) For Hotel: hotel
Data Copy(Board replacement )
Data copy
(Board replacement) or (Hotel)
Input password -----
Data Copy(Board replacement )
Input Password
2770 or 4850
Input password -----
Data Copy(Board replacement )
Copy TV to SD card
Performing
Please wait for a while
Please do not remove the SD card
GETTING
Data Copy(Board replacement )
Performing
Completion
Data copy has been successful
Please remove SD card
FINISH
20
Data Copy from SD Card to TV set
1. Turn on the TV set.
2. Insert SD card with Data to SD slot.
On-screen Display will be appeared according to the Data folder automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2771
(b) For Hotel: 4851
Data will be copied from SD card to TV set.
4. After the completion of copying to SD card, remove SD card from TV set.
(a) For Board replacement: Data will be deleted after copying (Limited one copy).
(b) For Hotel: Data will not be deleted and can be used for other TVs.
5. Turn off the TV set.
Note:
1. Depending on the failure of boards, function of Data for board replacement does not work.
2. This function can be effective among the same model numbers.
Data Copy(Board replacement )
Input Password
Input Password
2771 or 4851
Input password
Performing -----
Data Copy(Board replacement )
Copy SD card to TV
Performing
Please wait for a while
Please do not remove the SD card
WRITING
Data Copy(Board replacement )
Performing
Completion
Data copy has been successful
Please remove SD card
FINISH
21
Option Bytes Description
OPTION1
b1 TEXT Ch Refresh ON (1) / OFF (0)
b2 ID-1 ON (1) / OFF (0)
b3 Macrovision Auto-judge ON (1) / OFF (0)
b4 Surround enable low bit ON (1) / OFF (0)
b5 Surround enable high bit ON (1) / OFF (0)
b6 Enable HDMI force reset ON (1) / OFF (0)
b7 TINT_Component_HDMI ON (1) / OFF (0)
OPTION2
b0 Adjust gain enable ON (1) / OFF (0)
b1 A2 BG enable (5.5MHz) ON (1) / OFF (0)
b2 A2 DK1 enable (6.26MHz) ON (1) / OFF (0)
b3 A2 DK3 enable (5.742MHz) ON (1) / OFF (0)
b4 NICAM scan ON (1) / OFF (0)
b5 NICAM BG enable (5.5MHz) ON (1) / OFF (0)
b6 NICAM I enable (6.0MHz) ON (1) / OFF (0)
b7 NICAM DK enable (6.5MHz) ON (1) / OFF (0)
OPTION3
b0 NICAM priority ON (1) / OFF (0)
b1 Starhub scan enable (Singapore) ON (1) / OFF (0)
Enable special edge smoother ON (1) / OFF (0)
b2
function (CHINA)
b3 A2 DK2 enable ON (1) / OFF (0)
Inhibition of countermeasure ON (1) / OFF (0)
b4
for SIF signal drop
b5 Get onid from physical CH (CHINA) ON (1) / OFF (0)
SSU search enable for HOTEL ON (1) / OFF (0)
b6
model
b7 SASO mute (ASIA) ON (1) / OFF (0)
OPTION4
enable Video Distortion ON (0) / OFF (1)
b0
Countermeasure for Analog VIF.
b2 3DYC color motion detect ON (1) / OFF (0)
RF Clamp Current minimum ON (1) / OFF (0)
b3
(TAIWAN)
b4 SHOP banner enable ON (1) / OFF (0)
b6 PIP ON (1) / OFF (0)
Enable workaround for Polsat CAM ON (1) / OFF (0)
b7
problem (POLAND)
22
Adjustment Method
Sub-Contrast/White Balance Adjustment
Instrument Name Connect to Remarks
1. Remote controller Correlation can be also taken by
2. LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent
3. Comunication jig
4. Computer for external control
Procedure Remarks
Let the panel standfor more than 3
hours at more than 20 °ðC.
Basically perform adjustment in the
ambient environment of room
temperature more than 20 °ðC.
The aging time is more than20 min
at above room temperature.
Applied signal
Subcontrast adjustment
1. Receive PAL colour bar (100% white) RF signal.
100% full colour bar
2. Enter  Contrast adj. In SERVICE mode.
0.7V p-p white peak
3. Start adjusting by using Yellow Key.
85% modulation
4. If the adjustment finished normally, the letter of Contrast will change from red
to black.
White Balance adjustment
1. Procedure basically performs checking using the production software and
make automatic adjustment using external computer.
2. It adjusts in the mode of: Colour balance Normal
Viewing Mode Dynamic
Normal
Highlight x: 0.307 Ä…ð 0.010
y: 0.322 Ä…ð 0.010 100% WHITE
Normal
Lowlight x: 0.307 Ä…ð 0.010
50% GRAY
y: 0.322 Ä…ð 0.010
23


Wyszukiwarka