TAB 6 Navigational Safety Chapter 25 The Navigation Process


CHAPTER 25
THE NAVIGATION PROCESS
INTRODUCTION
2500. Fundamentals tem s optimum use varies as a function of the type of vessel,
the quality of the navigation equipment on board, and the ex-
This chapter emphasizes the operational aspects of navi- perience and skill of the particular navigator.
gating in the open ocean. It is in this operational process that For the watch officer, ensuring ship safety always
an individual navigator s experience and judgment become takes priority over completing operational commitments
most crucial. Compounding this subject s difficulty is the fact and carrying out the ship s routine. This chapter discusses
that there are no set rules regarding the optimum employment several basic safety considerations designed to minimize
of navigational systems and techniques. The navigation sys- the probability of human error leading to a marine accident.
VOYAGE PLANNING
Voyage planning determines the safest and most effi- and to determine the position of resulting track points.
cient track for the ship to follow to ensure that the vessel Transfer these points to a Mercator chart as a succes-
completes its operational commitments. Constructing a sion of waypoints connected by rhumb lines. Figure
planned track for a voyage is fundamentally important for 2501 illustrates this method. This figure shows a great
ship s safety. The commanding officer and the navigator circle route plotted as a straight line on a gnomonic
must carefully review and approve the track followed by the chart and as a series of points when transferred to a
conning officer. Several ships groundings have occurred be- Mercator chart. The arrows represent corresponding
cause of unauthorized deviations from an approved track. points on the two charts.
An operation order often assigns a naval vessel to an op-
2501. Constructing A Voyage Plan Track erating area. In that case, plan a track from the departure to the
edge of the operating area to ensure that the vessel arrives at
Construct the track using a navigation computer, a the operating area on time. Following a planned track inside
great circle (gnomonic) chart, or the sailings. This chapter the assigned area may be impossible because of the dynamic
will discuss only the navigation computer and the great cir- nature of a planned exercise. In that case, carefully examine
cle chart. Chapter 24 covers the sailings. Use a navigation the entire operating area for navigation hazards. If simply tran-
computer if one is available because the computer elimi- siting through the area, the ship should still follow a planned
nates the plotting errors inherent in transferring the track and approved track.
from gnomonic to a Mercator projection.
When using a navigation computer, the navigator simply 2502. Following A Voyage Plan
inputs the two endpoints of his planned voyage. The computer
computes waypoints marking the great circle track between the Complete the planning discussed in section 2501 prior
two endpoints. The computer determines each track leg s dis- to leaving port. Once the ship is transiting, frequently com-
tance and, given a speed of advance, calculates the times the pare the ship s actual position to the planned position and
vessel can expect to pass each waypoint. Construct the track on adjust the ship s course and speed to compensate for any
the Mercator chart by plotting the computer-generated way- deviations. Order courses and speeds to keep the vessel on
points and the tracks between them. track without significant deviation.
After adjusting the track as necessary to pass well clear of Often a vessel will have its operational commitments
any hazard, choose a speed of advance (SOA) that ensures the changed after it gets underway. If this happens, begin the
ship will arrive on time at any required point. Given an SOA, voyage planning process anew. Ensure the ship s navigator
mark the track with the ship s planned hourly positions. These and captain approve the new track corresponding to the new
planned positions are points of intended movement (PIM s). mission. The conning officer must understand that, unless
The SOA chosen for each track leg is the PIM speed. transiting in an operating area as discussed above, he
If a navigation computer is not available, use a gno- should never transit on a chart that does not have an ap-
monic chart to plot a great circle route between points proved track for him to follow.
371
372 THE NAVIGATION PROCESS
Figure 2501. Constructing a great circle track on a Mercator projection.
VOYAGE PREPARATION
2503. Equipment Inventory quired for an open ocean or coastal transit. Complete this
preparation well before using the chart to maintain the plot.
Prior to getting the ship underway, inventory all navi-
gation equipment, charts, and publications. The navigator Correcting The Chart: Correct all applicable charts
should develop a checklist of navigation equipment specific through the latest Notice to Mariners, Local Notice to Mar-
to his vessel and check that all required equipment is on- iners, and Broadcast Notice to Mariners. Ensure the chart to
board. The navigator should have all applicable Sailing be used is the correct edition.
Directions, pilot charts, and navigation charts covering his
planned route. He should also have all charts and sailing di- Plotting Approved Track: Section 2501 above discuss-
rection covering ports at which his vessel may call. He es constructing the track. Mark the track course above the track
should have all the equipment and publications required to line with a  C followed by the course. Similarly, mark each
support celestial navigation. Finally, he must have all tech- track leg s distance under the course line with a  D followed
nical documentation required to support the operation of his by the distance in nautical miles. Mark the PIM s at hourly in-
electronic navigation suite. tervals, and mark the time corresponding to each PIM.
Complete this chart, publication, and equipment inven-
tory well before the underway date and obtain all missing Calculating Minimum Expected, Danger, And
items before sailing. Warning Soundings: Chapter 8 discusses calculating mini-
mum expected, danger and warning soundings. Determining
2504. Chart Preparation these soundings is particularly important for ships passing a
shoal close aboard. Set these soundings to warn the conning
Just as the navigator must prepare charts for piloting, officer that he is passing too close to the shoal. Mark the min-
he must also prepare his charts for an open ocean transit. imum expected sounding, the warning sounding, and the
The following is a list of the minimum chart preparation re- danger sounding clearly on the chart and indicate the section
THE NAVIGATION PROCESS 373
of the track for which they are applicable. be able to glean the entire navigation situation from the
chart alone without reference to the directive from which
Marking Allowed Operating Areas: This chart prep- the chart was constructed. Therefore, put all operationally
aration step is applicable to military vessels. Often an important information directly on the chart.
operation order assigns a naval vessel to an operating area
for a specific period of time. There may be operational re- Marking Chart Shift Points: If the transit will require
strictions placed on the ship while within this area. For the ship to operate on more than one chart, mark the chart
example, a surface ship assigned to an operating area may points where the navigator must shift to the next chart.
be ordered not to exceed a certain speed for the duration of
an exercise. When assigned an operating area, clearly mark Examining 50nm On Either Side Of Track: High-
that area on the chart. Label it with the time the vessel must light any shoal water or other navigation hazard within
remain in the area and what, if any, operational restrictions 50nm of the planned track. This will alert the conning offic-
it must follow. The conning officer and the captain should er as he approaches a possible danger.
NAVIGATION ROUTINE AT SEA
2505. Frequency Of Position Determination sition during periods when external fix sources are
unavailable.
The table below lists recommended fix intervals as a Always check a position determined by a fix, inertial
function of navigation phase: navigator, or DR by comparing the charted sounding at the
position with the fathometer reading. If the soundings do
Piloting Coastal Ocean
not correlate, investigate the discrepancy.
Chapter 7 covers the importance of maintaining a
Frequency 3 min. or less 3-15 min. 30 min.
proper DR. It bears repeating here. Determine the differ-
ence between the fix and the DR positions at every fix and
Shorten the suggested fix interval if required to ensure use this information to calculate an EP from every DR.
the vessel remains at least two fix intervals from the nearest Constant application of set and drift to the DR is crucial if
danger. However, do not exceed the times recommended the vessel must pass a known navigation hazard close
above. Choose a fix interval that provides a sufficient safety aboard.
margin from all charted hazards.
Use all available fix information. With the advent of 2506. Fathometer Operations
accurate satellite navigation systems, it is especially tempt-
ing to disregard this maxim. However, the experienced Use Figure 2506 to develop a standard procedure for
navigator never feels comfortable relying solely on one par- operating the fathometer.
ticular system. Supplement the satellite position with
positions from Loran, celestial sights, radar lines of posi- 2507. The Modified Piloting Party
tion, and visual observations. Evaluate the accuracy of the
various fix methods against the satellite position; when the If operating out of piloting waters but near a navigation
satellite receiver fails, the knowledge, for example, that Lo- hazard, station a modified piloting party. As the name im-
ran fixes consistently plotted 1 nm to the west of GPS can plies, this team does not consist of the entire piloting party.
be helpful. It could consist of only the navigator or assistant navigator,
Use an inertial navigator if one is available. The iner- a plotter, and a recorder. Its purpose is to increase supervi-
tial navigator may produce estimated positions more sion of the navigation plot in areas that could pose a hazard
accurate than fix positions. Inertial navigators are com- to the vessel.
pletely independent of any external fix input. Therefore, The navigator and captain should develop a standing or-
they are invaluable for maintaining an accurate ship s po- der covering the stationing of a modified piloting party. A
Water Depth Sounding Interval
Charted Water Depth < 100 ft. Monitor fathometer continuously.
100 ft. < Charted Water Depth < 500 ft. Take and record soundings every 15 minutes.
500 ft. < Charted Water Depth < 1000 ft. Take and record soundings every 30 minutes.
Charted Water Depth > 1000 ft. Take and record soundings every hour.
Figure 2506. Fathometer operating guidelines.
374 THE NAVIGATION PROCESS
good rule is to station the modified piloting party when oper- 0800, 1200, and 2000 each day. Prepare these reports approx-
ating within 10 nm of a known hazard. imately 30 minutes ahead of the time when they are due. Use
the DR positions for the time of the report. For example, pre-
2508. Compass Checks pare the 2000 position report at 1930 using the ship s 2000 DR
position. Often the captain will require additional information
Determine gyro compass error at least daily as part of with these position reports. Some captains, for example, may
the at-sea routine. Check the gyro compass reading against want status reports on the engine room. Tailor each position re-
the inertial navigator if the vessel has an inertial navigator. port to contain the information the captain wants.
If the vessel does not have an inertial navigator, check gyro
error using the celestial techniques discussed in Chapter 17. 2511. Watch Relief Procedures
Report any error greater than 1° to the navigator and com-
manding officer. When a watch officer relieves as Officer of the Deck
Check the gyro repeaters and the magnetic compass (OOD), he assumes the responsibility for the safe naviga-
against the gyro compass hourly and after each course tion of the ship. He becomes the Commanding Officer s
change. When comparing the magnetic and gyro compasses, direct representative in ensuring ship safety. As such, he
account for changes in variation and deviation. Report any must prepare himself fully prior to assuming the watch. The
repeater error greater than 1° to the commanding officer. following list contains those items that, as a minimum, the
relieving OOD must check prior to assuming the watch.
2509. Commanding Officer s Night Orders And
Standing Orders " Conduct a Pre Watch Tour: The relieving OOD
should tour the ship prior to his watch. He should fa-
The Night Order book is the vehicle by which the cap- miliarize himself with any maintenance in progress.
tain informs the officer of the deck of the captain s orders He should check for general cleanliness and stow-
for operating the ship. The Night Order book, despite its age. He should order any loose gear that could pose
name, can contain orders for the entire 24 hour period after a safety hazard in rough seas secured.
which the CO issues it.
The navigator may write the Night Orders pertaining to " Check the Position Log and Chart: Check the type
navigation. Such orders include assigned operating areas, and accuracy of the ship s last fix. Verify that the nav-
maximum speeds allowed, required positions with respect to igation watch has plotted the last fix properly. Ensure
PIM, and, regarding submarines, the maximum depth at there is a properly constructed DR plot on the chart.
which the ship can operate. Each department head should in- Examine the DR for any potential navigation hazards.
clude in the Night Order book the evolutions he wants to Check ship s position with respect to the PIM. Ensure
accomplish during the night that would normally require the that the ship is in the correct operating area, if applica-
captain s permission. The captain can add further orders and ble. Check to ensure that the navigation watch has
directions as required. When the captain signs the Night Order properly applied fix expansion in accordance with the
book, it becomes an official order to the Officer of the Deck. navigator s instructions.
The Officer of the Deck must not follow the Night Or-
ders blindly. Circumstances under which the captain signed " Check the Fathometer Log: Ensure that previous
the Orders may have changed, rendering some evolutions watches have taken soundings at required intervals and
ordered impractical to complete. The Officer of the Deck, that the navigation watch took a sounding at the last fix.
when exercising his judgment on completing ordered evo- Verify that the present sounding matches the charted
lutions, must always inform the captain of any deviation sounding at the vessel s charted position.
from the Night Orders as soon as such a deviation occurs.
The Commanding Officer s Night Orders are in effect " Check the Compass Record Log: Verify that the
only for the 24 hours after they are written; his Standing Or- navigation watch has conducted compass checks at
ders are continuously in force. The captain sets the ship s the proper interval. Verify that gyro error is less than
navigation policy in these orders. He sets required fix inter- 1° and that all repeaters agree within 1° with the
vals, intervals for fathometer operations, minimum CPA s, master gyro.
and other general navigation and collision avoidance require-
ments. The Officer of the Deck must follow the Commanding " Read the Commanding Officer Night Orders:
Officer s Standing Orders at all times. Report any deviation Check the Night Order Book for the captain s direc-
from these orders immediately to the Commanding Officer. tions for the duration of the watch.
2510. Position Reports " Check Planned Operations: For any planned opera-
tions, verify that the ship has met all operational
If the captain requires position reports, deliver them at prerequisites, that the ship is in the correct operating
THE NAVIGATION PROCESS 375
area, and that all watchstanders have reviewed the op- relieve the watch. The on watch OOD then should brief the
eration order. If the operation is a complicated one, relieving OOD on the following:
consider holding an operations brief with applicable
watchstanders prior to assuming the watch. " Vessel s present course and speed.
" Vessel s present depth (submarines only).
" Check the Broadcast Schedule: Read any message " Any evolutions planned or in progress.
traffic that could have a bearing on the upcoming " The status of the engineering plant.
watch. If the ship is on a broadcast schedule, find out " The status of repair on any out of commission equip-
when the radio operator received the last broadcast ment that effects the ship s operational capability.
(military vessels only). Determine if the radio operator " Any orders from the Commanding Officer not ex-
pressly given in the Night Orders.
has any messages to transmit during the watch.
" Status of cargo (merchant vessels only).
" Any hazardous maintenance planned or in progress.
" Ascertain the Contact Situation: Check the radar and
" Any routine maintenance planned or in progress.
sonar contact picture, if so equipped. Determine which
" Any planned ship s drills.
contact has the closest CPA and what maneuvers, if any,
will be required to open CPA. Find out from the offgoing
If the relieving OOD has no questions following this
OOD if there have been any bridge-to-bridge communi-
brief, then he should relieve the watch. Upon relieving the
cations with any vessels in the area. Check that no CPA
watch, he should announce to both the helmsman and the
will be less than the minimum set by the Commanding
quartermaster that he has the deck and the conn. The quar-
Officer s Standing Orders.
termaster should log the change of watch in the ship s deck
log.
" Review Watchstander Logs: Review the log readings
Watch officers should not relieve the watch in the mid-
for all watchstanders. Note any out of specification
dle of an evolution or when casualty procedures are being
readings or any trends in log readings indicating that a
carried out. Relieve the watch only during a steady state op-
parameter will soon go out of specification.
erational and tactical situation. This ensures that there is
watchstander continuity when carrying out a specific evo-
After conducting the above listed checks, the relieving
lution or combating a casualty.
OOD should report to the on watch OOD that he is ready to
THE DAY S WORK IN CELESTIAL NAVIGATION
The advent of accurate electronic and satellite naviga- 4. Reduce a sun sight for a morning sun line.
tion systems has relegated celestial navigation to use solely 5. Calculate an azimuth of the sun for a compass
as a backup navigation method. Seldom if ever will a ship check. The navigator normally obtains an azi-
undertake an ocean transit relying only on celestial naviga- muth at about the same time as he takes a morning
tion. Therefore, the navigator need not follow the entire sun observation. He may also check the compass
routine listed below if celestial navigation is not his primary with an amplitude observation at sunrise.
navigation source. Use only the steps of the celestial day s 6. Observe the sun at local apparent noon. Cross
work that are necessary to provide a meaningful check on the resulting LOP with an advanced morning
the primary fix source s accuracy. Should the electronic sun line or with a longitude determined at LAN
navigation system fail, however, and should celestial navi- for a fix or running fix.
gation become the primary means of navigation, this 7. Reduce a sun sight during the afternoon. This
section provides a comprehensive procedure to follow. is primarily for use with an advanced noon sun
line, or with a moon or Venus line, if the skies
2512. Celestial Navigation Routine are overcast during evening twilight.
8. Calculate an azimuth of the sun for a compass
Complete a typical day s work in open celestial navi- check at about the same time as the afternoon sun
gation as follows: observation. The navigator may replace this azi-
muth with an amplitude observation at sunset.
1. Plot the dead reckoning position. 9. Reduce celestial observations for a fix during
2. Reduce celestial observations for a fix during evening twilight.
morning twilight.
3. Wind the chronometer and determine chro- Chapter 7, Chapter 17, and Chapter 20 contain detailed ex-
nometer error. planations of the procedures required to carry out this routine.
376 THE NAVIGATION PROCESS
Figure 2512. Typical celestial plot at sea.
SPECIAL CONSIDERATIONS FOR SMALL CRAFT
2513. Navigation Of Small Craft All craft venturing offshore should carry a properly
registered EPIRB and VHF radio. Loran C, Omega, and
In principle, the navigation of small craft is the same as GPS receivers are available; boats that transit out of sight of
that of larger vessels. However, because of a small craft s shal- land should have at least one of these.
lower draft, greater maneuverability, and possible limitations If the craft is to proceed out of sight of land for more
of equipment and expertise, there are important differences. than short intervals, celestial navigation equipment should
Small craft often spend most of their time within sight of land, be aboard. This equipment should include a sextant, an ac-
and their navigation is largely a matter of piloting. They gen- curate timepiece, a means of receiving time signals, an
erally are close enough inshore to reach safety in case of storm almanac, and sight reduction tables. Celestial navigation
or fog. Since most of them are primarily pleasure craft, there is calculators or computer programs are also useful.
a tendency for their navigation to be a less professional process A small craft navigator of limited experience may underes-
than in commercial or military craft. timate the importance of professional navigation. However, his
Regardless of the nature of the craft, it should carry the min- vessel s safety depends on his skill. He must plan his track and
imum safety equipment required by the U.S. Coast Guard. In know his position at all times. Small craft navigation also re-
addition to this Coast Guard mandated safety equipment, a small quires a complete, accurate, and neat plot. Where this is
craft should also carry a compass, charts, plotting devices, speed impractical because of heavy weather or limited plotting space,
log, tide tables, Coast Pilot or Sailing Directions, and binoculars. use a careful log and dead reckoning plot.
THE NAVIGATION PROCESS 377
CONCLUSION
2514. The Importance Of The Navigation Process position enroute are fundamental concepts of safe naviga-
tion. A mariner should never feel comfortable unless he is
Navigating a vessel is a dynamic process. Schedules following an approved track plotted on a corrected chart on
change; missions change. Planning a voyage is a process that be- which he has frequently updated his position.
gins well before the ship gets underway. Executing that plan does Developing and implementing such a routine is only
not end until the ship ties up at the pier at its final destination. half of the battle. Watchstanders must follow approved pro-
Develop a navigation process encompassing the prin- cedures. U.S. Navy grounding reports and U.S. Coast
ciples discussed in this chapter. Carefully planning a route, Guard accident reports attest to the danger courted when a
preparing required charts, and closely monitoring the ship s vessel disregards basic navigation safety.


Wyszukiwarka

Podobne podstrony:
TAB 6 Navigational Safety Chapter 29 Position Reporting Systems
TAB 6 Navigational Safety Chapter 30 Hydrography and Hydrographic Reports
TAB 6 Navigational Safety Chapter 28 Global Maritime Distress and Safety System
TAB 6 Navigational Safety Chapter 26 Emergency Navigation
TAB 5 Navigational Mathematics Chapter 22 Navigational Calculations
TAB 5 Navigational Mathematics Chapter 23 Navigational Errors
25 The Nine Worlds Their Shaping and End
Chapter 25 User defined conversions csproj FileListAbsolute
E C Tubb Dumarest 25 The Terridae
Chapter 3b The First Law Closed Systems Stirling Ebdines (updated 9 10 2013)
Chapter 11 The Developer s Exam
25 Polarimetric SAR Process
[13]Role of oxidative stress and protein oxidation in the aging process
THE PAPERMAKING PROCESS
The Translation Process Methods and Problems of its Investigation
The Visual Process Method A New Method to Study Physical Attractiveness
Dhyana Vahini Chapter V Cultivate the Blissful Atmic Experience

więcej podobnych podstron