Glow Worm installation and service manual Ultimate 40CF UIS


221785B.11.00
Instructions for Use
Installation and Servicing
To be l ef t wi t h t he user
40CF
G.C. No. 41 319 48
Open Flue Boiler
BS 6332
BS 5258
This is a Cat I2H Appliance
Reference in these instructions to British Standards and Statutory
Regulations/Requirements apply only to the United Kingdom.
The instructions consist of three parts, User, Installation and Servicing Instructions, which includes the Guarantee Registration Card.
The instructions are an integral part of the appliance and must, to comply with the current issue of the Gas Safety (Installation and Use)
Regulations, be handed to the user on completion of the installation.
Guarantee Registration
Thank you for installing a new Glow-worm appliance in your home.
Glow-worm appliances' are manufactured to the very highest standard so we are pleased to offer our customers' a
Comprehensive First Year Guarantee.
Attached to the center of these instructions is your Guarantee Registration Card,
which we recommend you complete and return as soon as possible.
If this card is missing you can obtain a copy or record your registration by telephoning the
Heatcall Customer Service number 01773 828100.
Our Guarantee gives you peace of mind plus valuable protection against breakdown by covering the cost of:
' REGISTER YOUR GLOW-WORM APPLIANCE
All replacement parts
O'
FOR 1ST YEAR GUARANTEE PROTECTION
' All labour charges
O'
' All call-out charges
O'
CALL 0208 247 9857
Hepworth Heating Ltd.,
Customer Services:
Nottingham Road, Belper, Derbyshire. DE56 1JT
Tel: (01773) 828100
General/Sales enquiries:
Tel: (01773) 824141 Fax: (01773) 820569
One Contact Local Service Fax: (01773) 828070
2143
Important Information
Testing and Certification
This boiler is tested and certificated for safety and performance. It is therefore important that no alteration is made to the boiler, without
permission, in writing, from Hepworth Heating Ltd.
Any alteration not approved by Hepworth Heating Ltd., could invalidate the certification, boiler warranty and may also infringe the
current issue of the Statutory Requirements, see Section 1.4.
CE Mark
This boiler is exempt from the general requirements of the Boiler (Efficiency) Regulations (1993) and Directive 92/42/EEC by reason
of its conformity to Schedule 3.I.7 of those Regulations and Article 4.3 of that Directive.
The CE mark on this appliance shows compliance with:
1. Directive 90/396/EEC on the approximation of the laws of the Member States relating to appliances burning gaseous fuels.
2. Directive 73/23/EEC on the harmonization of the Laws of the Member States relating to the electrical equipment designed
for use within certain voltage limits.
3. Directive 89/336/EEC on the approximation of the Laws of the Member States relating to electromagnetic compatibility.
INFORMATION FOR THE INSTALLER AND SERVICE ENGINEER.
Under Section 6 of The Health and Safety at Work Act 1974, we are required to provide information on substances hazardous to
health.
CERAMIC FIBRE/INSULATION PADS, GLASSYARN.
These can cause irritation to skin, eyes and the respiratory tract. If you have a history of skin complaint you may be susceptible to
irritation. High dust levels are usual only if the material is broken. Normal handling should not cause discomfort, but follow normal
good hygiene and wash your hands before eating, drinking or going to the lavatory. If you do suffer irritation of the eyes or severe
irritation to the skin seek medical attention.
THERMOSTATS
These contain very small amounts of xylene in the sealed phial and capillary. If broken, under normal circumstances the fluid does
not cause a problem, but in case of skin contact, wash with cold water. If swallowed drink plenty of water and seek medical attention.
CONTENTS DESCRIPTION SECTION PAGE No.
Introduction 3
INSTRUCTIONS
Lighting the Boiler 4
FOR USE
General Data 1 5
INSTALLATIONS
Flue & Ventilation 2 6
INSTRUCTIONS Water Systems 3 7
Installation 4 8
Electrical Connection 5 10
Commissioning 6 11
User Information 7 13
Servicing and Replacement Parts 8 13
SERVICING
Fault Finding 9 17
INSTRUCTIONS
Spare Parts 10 20
221785B 2
Instructions for Use
Cleaning
Introduction
WARNING. This appliance contains metal parts (components)
Please read these instructions and follow them carefully for the
and care should be taken when handling and cleaning, with
safe and economical use of your boiler.
particular regard to edges.
The Ultimate series are central heating boilers designed to
Clean the casing occasionally by wiping it over with a damp
provide heating and indirect domestic hot water.
soapy cloth or dry polishing duster.
Important Notice
Do not use an abrasive cleaner.
This boiler is for use only on natural gas G20.
Boiler Electrical Supply
The Gas Safety (Installation and Use)
Warning. This boiler must be earthed.
Regulations
The boiler must be connected to a 230V~50Hz supply, protected
In your interests and that of gas safety it is the Law that ALL gas by a 3A fuse.
appliances are installed by competent person in accordance
All wiring must be in accordance with the current issue of
with the current issue of the above regulations.
BS7671.
Cables, PVC insulated type, to the current issue of BS6500
Gas Leak or Fault
Table 16, 0.75mm2 (24/0.20mm) only may be used to connect
If a gas leak or fault exists or is suspected, the BOILER MUST
the boiler up.
BE TURNED Off, including the electrical supply and MUST
NOT BE USED UNTIL THE FAULT HAS BEEN PUT RIGHT.
Advice/help should be obtained from your installation/servicing
company or the local gas undertaking.
Maintenance
To ensure the continued efficient and safe operation of the
boiler it is recommended that it is checked and serviced as
necessary at regular intervals. The frequency of servicing will
depend upon the particular installation conditions and usage,
but in general once a year should be enough.
If this appliance is installed in a rented property there is a duty
260mm
of care imposed on the owner of the property by the current
issue of the Gas Safety (Installation and Use) Regulations,
Section 35.
Additional clearances may
It is the Law the any servicing be carried out by a competent
person. be required for installation
To obtain service, please call your installer or Heatcall (Glow-
worm s own service organisation) using the telephone number
given on the control tray.
Please be advised that the  Benchmark logbook should be
108mm
completed by the installation engineer on completion of
commissioning and servicing.
All CORGI Registered Installers carry a CORGI ID card, and
have a registration number. Both should be recorded in your
boiler Logbook. You can check your installer is CORGI
registered by calling CORGI direct on :- 01256 372300.
6mm
6mm
Boiler Clearances
If fixtures are positioned close to the boiler space must be left
as shown in diagram 1. Enough space must also be left in front
of the boiler to allow for servicing.
The convection air openings on top of the boiler must never
obstructed.
Boiler Installed in a Compartment or Cupboard
If the boiler is installed in a compartment or cupboard do not
TO
100mm
obstruct any ventilation openings.
915mm
FLOOR
WORKTOP
Do not use the compartment or cupboard for storage.
Diagram 1
3 221785B
2166
Instructions for Use
Connecting an Electrical Plug Turn thermostat knob  B faulty anticlockwise to the  O Off
position.
The colours of three core flexible cable are, Brown - live, Blue
Push in control knob  D , keep pushed in, push and release
- neutral, Green and Yellow - earth.
piezo button  A until the pilot lights.
As the marking on your plug may not correspond with these
Look through window  E .
colours continue as follows:
After the pilot burner lights keep the button pushed in for about
The wire coloured brown must be connected to the terminal
20 seconds. Check that the pilot is alight and stable, look
marked  L or Red.
through window  E . If the pilot burner fails to stay alight, wait
The wire coloured blue must be connected to the terminal
3 minutes before repeating the lighting operation.
marked  N or Black.
The safety device may also need resetting, refer to the
The wire coloured green and yellow must be connected to the
instructions above.
terminal marked  E or Green or the earth symbol .
The flue blockage safety device may also need resetting, refer
to instructions above.
Safety Device
Turn thermostat control knob  B to a setting between  MIN and
The boiler is fitted with a flue blockage safety device which will
 MAX and the main burner will light.
shut it down if there is a problem with the chimney. This device
 MAX is about 82oC (180oF).
is NOT a substitute for an independently mounted Carbon
Monoxide detector.
The above sequence must be carried out every time that the
burner is relit.
The safety device is reset, after three minutes, by pushing in the
button shown in diagram 2.
Check that all external controls are calling for heat.
Shut down can occur during certain climate conditioned, but if
To Turn the Boiler Off
it recurs the chimney flue and air inlet into the room must be
checked and any problems found corrected by a competent
For short periods, turn the thermostat knob fully clockwise to  O
person, before the boiler is used again.
Off. To relight, turn thermostat knob anticlockwise to any
position between  MIN and  MAX .
Any problems found must be put right, by a competent person,
before the boiler is used again.
For longer periods, turn the thermostat knob fully clockwise to
 O Off. Slide the gas control button  D inward and release, see
To Turn the Boiler On
diagram 2. Switch off the electrical supply to the boiler.
Turn the electrical supply on to the boiler and check that any
To relight, follow the full lighting sequence given above.
remote controls are set to your requirements (refer to
manufacturer s instructions supplied with these items).
Protection Against Freezing
WARNING. If the pilot flame goes out either intentionally or by
If the boiler is to be out of use for any long period of time during
accident, no attempt should be made to relight it for at least
severe weather condition we recommend that the whole system,
three minutes.
including the boiler, be drained off to avoid the risk of freezing
up. Make sure that, if fitted, the immersion heater in the cylinder
Slide to controls cover off and clear.
is switched off.
Identify the controls by reference to diagram 2.
The serial number and GC number of the boiler can be found on
Switch off the electrical supply to the boiler.
the data label.
Check that the flue blockage safety device has not operated,
that is, the button is in. Refer to Safety Device instructions.
A PIEZO UNIT BUTTON
B THERMOSTAT CONTROL KNOB
C GAS SERVICE COCK (SHOWN IN OFF POSITION)
D CONTROL BUTTON (GAS)
E
E VIEWING WINDOW
F FLUE BLOCKAGE SAFETY DEVICE
RESET BUTTON
A C D
B F
DATA LABEL
Diagram 2
221785B 4
8043
INSIDE DIAMETER R
B M
OF SOCKET FOR
K 100mm (4in)
S
NOMINAL
E
DIAMETER FLUE
C D
L
C
L
C FLUE
N
A
L
H
F
1 1
GAS CONNECTION RC /2 ( /2 in. BSPT) WATER CONNECTION RC1 (1in. BSPT)
Diagram 1.1
GENERAL DIMENSIONS (all dimensions in mm)
MODEL A B C D E F H K L M N R S
40CF
764 265 168 213 149 24.5 39 115 741 417 640 345 23
1 General Notes and Information 1.4 BSI Certification
This boiler is for use on natural gas G20. The boiler is certificated to the current issue of BS6332 Part 1,
invoking the current issue of BS5258 Part 1 for performance
Wherever possible, all materials, appliances and components
and safety. It is, therefore, important that no alteration is made
to be used shall comply with the requirements of applicable
to the boiler without permission, in writing, from Hepworth
British Standards.
Heating Ltd.
Where no British Standard exists, materials and equipment
Any alteration that is not approved by Hepworth Heating Ltd.,
should be fit for their purpose and of suitable quality and
could invalidate the BSI Certification of the boiler, warranty and
workmanship.
could also infringe the current issue of the Statutory
This boiler is not suitable for use out of doors.
Requirements.
Sheet Metal Parts
1.5 Gas Supply
WARNING. When installing or servicing the boiler care should
The gas installation shall be in accordance with the current
be taken when handling sheet metal parts, to avoid any possibility
issue of BS6891.
of personal injury.
The supply from the governed meter must be of adequate size
1.1 Statutory Requirements
to provide a steady inlet working pressure of 20mbar (8in wg) at
The installation of the boiler must be carried out by a competent the boiler.
person in accordance with the relevant requirements of the
current issue of:
1.2 DATA
Manufacturer s instructions, supplied.
The Gas Safety (Installation and Use) Regulations, WEIGHT (approx) 45.0 kg
(99.0lb)
The Building Regulations, Local Water Company Byelaws, The
Building Standards (Scotland) Regulations (applicable in
Scotland), The Health and Safety at Work Act, Control of 5.6 litres
WATER
Substances Hazardous to Health, The Electricity at Work
CONTENT
(1.23 gal)
Regulations and any applicable local regulations.
GAS
Detailed recommendations are contained in the current issue of
1
Rc /2
CONNECTION
the following British Standards and Codes of Practice:
BS6798, BS5440 Parts 1 and 2, BS5546 Part 1, BS5449,
WATER
Rc1
BS6891, BS7478, BS7593, BS7671.
CONNECTION
Manufacturer s instructions must not be taken as overriding
ELECTRICITY
statutory requirements.
230V~50Hz, fused 3A
SUPPLY
1.3 Range Rating
DATA
On right hand side of electrical
The boiler is range rated and may be adjusted to suit the
LABEL
control box
individual system requirements.
The respective Table 1 gives the ratings and settings.
5 221785B
0020M
0020M
1 General Data
On completion test the gas installation for soundness using the The boiler must not be installed in a room used or intended to
pressure drop method and suitable leak detection fluid, purge be used as sleeping accommodation or a room containing a
in accordance with the above Standard. bath or shower.
The boiler must be mounted on a flat wall which is sufficiently
1.6 Electrical Supply
robust to take its weight.
WARNING: This boiler must be earthed.
1.12 Boiler Clearances
All system components shall be of an approved type and shall
be connected in accordance with the current issue of BS7671 Refer to diagram 4.4.
and any applicable local regulations.
The boiler must be positioned so that at least the minimum
Connection of the boiler and system controls to the mains operational and servicing clearances are provided.
supply should be through a common isolator fused at 3A,
Additional clearances may be required for installation.
maximum. This method of connection should be by a switched
If fixtures are positioned next to the boiler they should be made
spur box with a minimum contact separation of 3mm in both
removable for access to pipework.
poles. It should be clearly marked, showing its purpose,
preferably positioned close to the boiler.
Sufficient clearance must be left in front of the boiler for
servicing.
Alternatively an unswitched socket outlet and three pin plug,
fused 3A, to the current issue of BS1363 may be used.
1.13Heating System Controls
Wiring to the boiler must be PVC insulated cable at least
The heating system should have installed: a programmer and
0.75mm2 (24/0.20mm) to the current issue of BS6500 Table 16.
room thermostat controlling the boiler.
1.7 Contents of Packaging
Thermostatic radiator valves may be installed in addition to the
room thermostat.
The boiler is delivered in one pack which contains:
Note: For further information, see The Building Regulations
Boiler with outer case and wall frame, side panels, burner,
1991 - Conservation of fuel and power, 1995 edition - Appendix
combustion chamber shield, flueway baffle and loose items
G, table 4b.
pack.
1.8 Water System
TABLE 1
The boiler shall only be used on an unrestricted open vented
system with the water supply taken from a feed and expansion ULTIMATE 40CF RANGE RATING
tank, having a head between 1m (3ft 3in) minimum and 27m
(90ft) maximum. RANGE RATING Min. Max.
NOMINAL kW
11.69 15.36
1.9 Draining Tap
HEAT INPUT
A draining tap must be provided at the lowest point of the system
(GROSS) Btu/h 39,900 52,400
which will allow the entire system, the boiler and hot water
NOMINAL kW
8.79 11.72
cylinder to be drained.
HEAT
OUTPUT Btu/h
Draining taps shall be to the current issue of BS2879. 30,000 40,000
BURNER mbar
8.1 14.2
1.10 Safety Valve
SETTING
PRESSURE in.w.g 3.3 5.7
A safety valve need not be fitted to an open vented system.
APPROX. m3/h
1.13 1.47
1.11 Location
GAS
WARNING. Open flue boilers must not be installed in a private RATE ft3/h 40 52
garage.
BURNER :- FF2029
INJECTOR
MARKING
PILOT :- 7215
2 Flue and Ventilation
Important Note
COMPARTMENT AIR VENT TABLE 2.
The boiler is fitted with a Flue Blockage Safety Device, which
will shut down the boiler if there is an unacceptable spillage of
ULTIMATE 40CF
products at the draught diverter.
COMPARTMENT
This safety device MUST NOT under any circumstances be HIGH LEVEL LOW LEVEL
VENTILATION
interfered with or put out of action.
VENT AREA VENT AREA
REQUIREMENTS
The safety device must only be replaced with the Glow-worm
parts.
FROM ROOM
140cm2 22in2 278cm2 44in2
OR SPACE
2.1 Flue Connection
The integral draught diverter makes the combustion performance
FROM
independent of conditions in the secondary flue, but an efficient 70cm2 11in2 139cm2 22in2
OUTSIDE
flue is necessary to ensure a trouble free installation.
221785B 6
2 Flue and Ventilation
The flue must be installed in accordance with the 2.2A Boilers in a Room or Space
recommendations in the current issue of BS5440 Part 1.
A purpose designed ventilation opening must be provided on an
The flue should be kept as short as possible. outside wall of the building, this opening may be either, directly
into the room or space containing the boiler, or into an adjacent
Horizontal or very shallow runs should be avoided.
room or space which has an internal permanent air vent of the
Give maximum possible vertical rise from the boiler, minimum
same size to the room containing the boiler.
600mm (24in) before any bend.
Do not ventilate through a kitchen, private garage, bathroom or
The use of 45o bends is recommended.
toilet.
A slip-on loose collar must be provided for flue removal.
Vents through a cavity wall must be ducted.
End with a certificated terminal, above ridge height, if possible,
If there are other fuel burning appliances present, allowance
if not, at least above the eaves of a pitched roof.
must be made for their combustion requirements. The free area
for the boiler is:
A previously used chimney must be swept and any register
plate or damper or the like must be removed or locked in the
40CF - 38cm2 (5in2)
open position and the chimney made good.
Refer also to the current issue of BS5440 Part 2.
2.2 Boilers in a Compartment
2.3 Products of Combustion
Where the installation of the boiler will be in an unusual location,
Test the boiler for clearance of flue products at the draught
special procedures are necessary. Refer to the current issue of
diverter as detailed in the current issue of BS5440 Part 1.
BS6798 for guidance.
A compartment used to enclose the boiler must be designed 2.4 Extract Fans
and constructed specifically for this purpose.
If an extract fan is fitted there is a possibility that if adequate air
An existing cupboard or compartment modified for the purpose is not provided spillage of the flue products could occur. If vents
may be used. Refer to the current issue of BS6798 for are fitted in accordance with the above recommendations this
guidance. should not occur.
The doorway opening should be of sufficient size to allow for Where such an installation is found a spillage test must be
easy removal of the boiler. carried out as detailed in the current issue of BS5440 Part 1 and
any necessary action taken.
Be provided with permanent ventilation openings as shown in
the respective Table 2. These figures are for the minimum free
2.5 Timber Frame Buildings
area.
If the boiler is to be installed in a timber frame building it should
The high and low level openings must communicate with the
be fitted in accordance with the Institute of Gas Engineers
same room or space or must both be on the same wall to outside
document IGE/UP/7/1998. If in doubt seek advice from the local
air.
gas undertaking or Hepworth Heating Ltd.
The compartment door or vent should not communicate with a
private garage, bedroom, bed sitting room or a room containing
a bath or shower.
3 Water Systems
Frost Protection
22mm VENT
If the position of the boiler is such that it may be vulnerable to
freezing it should be protected as specified in the current issue
15mm COLD FEED
of BS5422. It is also recommended that a frost protection
thermostat be fitted.
INDIRECT
3.1 Cylinders
CYLINDER
(Shown with
For all systems supplying domestic hot water the cylinder must
27 metres
recommended
be indirect. It is recommended that the cylinder be fitted with Max.
thermostat and valve).
some form of temperature control.
HEATING
3.2 Gravity Domestic Hot Water with Pumped SYSTEM
PUMP
Heating
28mm
It is important that the flow and return connections are in the
MIDWAY BETWEEN
same relative positions as shown in diagram 3.1.
BOILER TAPPINGS
The domestic flow and return must both be on one side of the
REFER TO BS 5546
heat exchanger. The heating flow and return are taken from the
other.
GRAVITY HOT WATER
SYSTEM (DIAGRAMMATIC) Diagram 3.1
7 221785B
3 Water Systems
3.3 Pumped Heating and Hot Water 3.4 Pump
It is important the flow and return connections are made as This should be fitted on the flow pipe and have isolating valves
shown in diagram 3.2. fitted each side, integral, if possible.
These connections may be fitted on the opposite side to that The pump should be set to give a temperature difference of
shown but always in the same relative positions. 11oC (20oF) between flow and return, with the boiler thermostat
set at  MAX which is about 82oC (180oF).
The resistance through the boiler can be found from diagram
22mm VENT &
3.3.
15mm COLD FEED
TO BE FITTED IN
ACCORDANCE
WITH BS 6798
INDIRECT
120
CYLINDER
100
ALTERNATIVE
1metre Min.
SYSTEM
27 metres
80
CONTROL
Max.
VALVES
60
14.7
HEATING
11.7
SYSTEM 40
PUMP
8.8
20
5.9
MIDWAY BETWEEN
0 0
BOILER TAPPINGS
0 5 10 15 20 25 30
Flow rate (litres/minute)
4 Installation
4.1 Unpacking Release the wall frame by removing and keeping the two
retaining screws at the back of the combustion chamber, see
Unpack and check that the contents, listed below, are present
diagram 4.2.
and undamaged:-
To remove the boiler, turn it over, sideways, out of the bottom
Boiler, combustion chamber shield, side panels x 2, burner,
tray, see diagram 4.3, taking care not to damage the controls,
flueway baffle, loose items pack (with check list).
so that it is face down on the floor, exposing the four Rc1 (1in
With the boiler still in the bottom tray, slide the controls cover
BSP) water connections.
upwards and remove as shown in diagram 4.1. Remove the
Remove the remaining loose items, including the wall frame
outer case by undoing, and retaining), the two screws and lifting
which is in the bottom of the tray.
off, see diagram 4.1.
CONTROLS COVER
SECURING SCREW
BOILER
OUTER CASE
SECURING
SCREW(S)
CONTROLS COVER &
SECURING BOILER
OUTER CASE REMOVAL Diagram 4.1 TO WALL FRAME Diagram 4.2
221785B 8
0023M
Water pressure loss
(mm head of water)
HEAT SETTING (kW) To give a water
flow rate differential of 11ÚC (20ÚF)
089
8044
4 Installation
Note: It is NOT recommended that the boiler be placed in an
upright position. If it is unavoidable great care must be taken not
to damage the gas valve, to avoid this it is suggested that
support be placed under the boiler, positioned as shown in
B
diagram 4.3.
4.2 Preparation
G
D
Use the wall frame and refer to diagram 4.4, mark out the
position of the fixing holes, making sure they are square.
Remove the wall frame and drill holes to suit plugs and screws
provided. Secure the wall frame with its cross member at the
top, to the wall.
Make sure the wall frame is level.
C
E
L
Fit suitable Rc1 (1in BSP) fittings into the appropriate tappings.
Tighten to required position and then fit suitable fittings and
short lengths of pipe into these fittings, making sure that they will
be in an accessible position when the boiler is fixed.
A
Note: It is important to make sure that all these joints are
H
watertight at this stage as they will not be directly accessible
after the boiler is fixed.
C
4.3 Mounting the Boiler
Note: Access to the screw holes is through the combustion
FF
chamber, see diagram 4.3. Take care not to damage the pilot
and thermocouple assembly.
Lift the boiler and position on to the wall frame so that the tags
on the boiler body locate on the cross member of the wallframe,
A L.H. and R.H. side of casing 6
see diagram 4.5. Fasten the boiler to the wallframe, using the
B Top of casing to ceiling/fixture 108
screws previously removed.
Remove the flue cleaning door, see diagram 4.6. C Bottom of casing to floor/fixture 100
Remove the split pin. Withdraw the retaining angle and
D Top fixing holes to ceiling/fixture 441
thermostat phial from its pocket.
E Fixing holes-upper to lower 210
Fit the flueway baffle, making sure that it is seated down
correctly onto the casing as shown in diagram 4.6.
F C to R.H. and L.H. wall fixture 215
L
Re-assembly note: When fitting the thermostat, make sure that
G Fixing holes-R.H. to L.H. 204
the thermostat is fully inserted into the phial pocket and then
insert the retaining angle. H Lower fixing holes to floor/fixture 305
Replace the flue cleaning door.
Diagram 4.4
FIXING HOLE POSITIONS
DO NOT STAND UPRIGHT UNLESS A
TURNOVER
SUPPORT IS USED TO AVOID
DAMAGE TO THE MULTI-
WALL FRAME
FUNCTIONAL CONTROL
CROSS
MEMBER
SUPPORT
SECURING BOILER
Diagram 4.3
SUPPORTING THE BOILER TO WALL FRAME Diagram 4.5
9 221785B
0021
2944
2156
8045
4 Installation
4.4 Water Circulation System
Complete the water connections to the boiler pipework, using
compression fittings.
Fill, vent and cold flush the system as recommended in the
current issue of BS6798.
Visually check for and put right any water leaks.
4.5 Gas Connection
FLUE
FLUE
Make the gas connection to the flanged Rc1/2 gas service cock.
CLEANING
SOCKET
DOOR
4.6 Flue
GUIDE (2)
Install the flue pipework and seal to the flue socket in accordance
with normal practice.
SECURING
SCREW
WASHER (2)
SELF-TAPPING
FLUEWAY BAFFLE
SECURING SCREW (2)
Diagram 4.6
FLUE CLEANING DOOR
5 Electrical Connection
5.1 Control Box Removal 5.2 Cable Connection
Remove the electrical control box securing screw, see diagram Thread the mains cable through the clamp at the rear of the
5.1. Pull the control box down at the front and pull forwards to control box and connect to the terminal strip, see diagram 5.2.
release from hook at rear, see diagram 5.2.
The earth conductor must be made of a greater length so that
if the cable is strained the earth conductor is the last to become
disconnected.
EARTH
ELECTRICAL
CONTROL BOX
SECURING
SCREW (1)
MAINS
CABLE
TERMINAL
PIEZO
STRIP
UNIT
MAINS CABLE
PIEZO UNIT Diagram 5.1
CONNECTION Diagram 5.2
221785B 10
2122
8047
8038
5 Electrical Connection
Connect to the terminal strip, as shown in diagram 5.3.
5.3 Testing
Secure the cable into the clamp, as shown in diagram 5.2.
Checks to ensure electrical safety should be carried out by a
competent person.
Make sure that there is sufficient cable to allow the control box
to be temporarily hooked into the front slot, to allow for servicing.
It is essential that the polarity is correct.
Replace the control box by reversing the information given
In the event of an electrical fault after installation of the system,
above in Section 5.1. Take care not to trap the thermostat
the preliminary electrical system checks, as below should be
capillary at the rear of the control box also make sure the rear
carried out:
location hook is correctly engaged.
1. Test insulation resistance to earth of mains cable.
2. Test earth continuity and short circuit of all cables.
3. Switch on the electrical supply to the boiler and test the
polarity of the mains supply.
GRN/YEL
230V~50Hz PERMANENT MAINS
BLUE
SUPPLY FUSED AT 3 AMP
BROWN
E N L
EARTH
GRN/YEL
BLUE
GRN/YEL
BROWN
NC C
THERMOSTAT
MULTI-FUNCTIONAL
CONTROL
ELECTRICAL
BLUE
GRN/YEL
CONNECTIONS -
BROWN
Diagram 5.3
BOILER COMPONENTS
6 Commissioning
Please ensure the "Benchmark" logbook is completed and left
Do not attempt to relight until the safety device has reset, that
with the user.
is, after a minimum of 3 minutes.
Note. Should the boiler fail to operate correctly refer to Fault
6.1 Testing, Initial Lighting and Adjustment
Finding Section.
Make sure that all naked lights, pipes and cigarettes are out.
Check the length of the pilot flame, it should envelop the
Pressure test the complete installation for soundness and
thermocouple tip as shown in diagram 6.3. The pilot rate can be
purge in accordance with the current issue of BS6891.
adjusted, if necessary, by turning the pilot burner adjustment
screw  N , having first removed the multifunctional control cover
Refer to diagram 6.1 to fit the burner.
by releasing the screw as diagram 6.4.
Identify the controls by reference to diagram 6.2.
Test pilot supply connections for gas soundness, using a
Check that the gas service cock  C is off, that is, indicator
suitable leak
vertical.
detection fluid.
Check that the mains electrical supply to the boiler is off.
Hook the combustion chamber shield onto the front of the
Set the thermostat control knob  B to  O - the off position.
combustion chamber, making sure that it is flush and horizontal
with the combustion chamber front, see diagram 6.1.
Remove the gas pressure test nipple screw  E and fit a suitable
pressure gauge.
Fit the outer case, making sure that the lower part clears the pilot
supply tube. Secure with the screws previously removed.
Open gas service cock  C .
Make sure that the pilot is alight and stable by viewing through
Note. Make sure that the flue blockage safety device reset
the window in the casing.
button  P is fully pushed in.
Switch on the electrical supply to the boiler and turn on all
Push in control button  K , keep pressed in and at the same time
external controls.
operate the piezo unit button  G until the pilot burner lights.
Set the thermostat knob  B between  MIN and  MAX and
After the pilot burner lights keep the button  K pushed in for
check that the main burner cross lights smoothly from the pilot.
about 15 seconds. If the pilot burner fails to light or stay alight
Whilst the boiler is operating test gas valve and gas connections
a safety device in the multifunctional control prevents immediate
for gas soundness using a suitable leak detection fluid.
re-lighting.
11 221785B
8049
BLK
BLUE
6 Commissioning
To set the burner pressure, operate the boiler for 10 minutes, Check the operation of the flame failure device, with the burner
remove the multifunctional control cover, if not already removed, alight, as follows:- Slide the control button  K inwards and
as above. Adjust the gas burner pressure by screw  F until the release, the main burner and pilot will go out. Check that the
required pressure is obtained, see the relevant Table 1 for flame failure device has operated, indicated by a  click , within
setting pressures. 60 seconds, from the valve. The multifunctional control
incorporates a safety device. Do not attempt to relight until it has
Stick the self adhesive arrow from the loose items pack onto the
reset, in about 3 minutes.
appropriate space beneath the  Min or  Max column on the
data label. Remove the pressure gauge and refit the screw  E , making
sure that a gas tight seal is made.
Should any doubt exist about the gas rate this should be
checked at the meter using a stop watch to time at least a cubic Set the thermostat knob  B to  O (the off position) and relight
foot of gas consumption. the pilot, as above.
Replace the multifunctional control cover.
10 to 14mm
SPARK
ELECTRODE
COMBUSTION
CHAMBER
SHIELD
BURNER
HEX
PILOT BURNER
SECURING
NUT
BURNER PIN
2.5 TO 5.0mm
AND HOLE
(1/8 in) (3/16 in)
LOCATION
SPARK GAP
Diagram 6.1
BURNER LOCATION Diagram 6.3
AND FLAME DIMENSION
M
G B AH P C KD
E
A ELECTRICAL CONTROL BOX
B THERMOSTAT CONTROL KNOB
C GAS SERVICE COCK(SHOWN IN OFF POSITION)
N
D MULTI-FUNCTIONAL CONTROL
E PRESSURE TEST NIPPLE
F GAS BURNER TEST NIPPLE
G PIEZO UNIT BUTTON
H THERMOCOUPLE PIPE
K CONTROL BUTTON (GAS)
M CASE SECURING SCREW
F
N PILOT BURNER PRESSURE SCREW
INSET VIEW
P FLUE BLOCKAGE SAFETY DEVICE
With multi-functional control valve
RESET BUTTON
cover removed for clarity
Diagram 6.2
BOILER COMPONENTS
221785B 12
2157
2145
8052
6 Commissioning
Check that the boiler thermostat and all external controls are Relight the main burner and allow the system to warm up.
operating as required.
There should be no undue noise in the system and no pumping
Do not attempt to adjust the thermostat calibration screw. over of water or entry of air at the open vent.
Allow the system to reach maximum temperature and check for
water soundness.
COVER
The burner should then be turned off and the system drained,
as rapidly as possible, to complete the flushing process. Refill
the system, heat up, vent and check again for water soundness.
If the side panels are to be fitted, remove the outer case. (Fit by
fastening to the outer case using the securing screws, see
diagram 6.5.)
Refit outer case and controls cover.
COVER
GAS SERVICE
SECURING
COCK
SCREW
PILOT SUPPLY TUBE
THERMOCOUPLE
NUT
SECURING
SCREW (6)
SIDE
PANEL
BURNER
SUPPLY
BROWN
TUBE
GREEN/YELLOW
BLUE
MULTI-FUNCTIONAL
Diagram 6.5
Diagram 6.4 SECURING SIDE PANELS
CONTROL
7 User Information
Hand the Instructions for Use to the user for their retention. Advise that the boiler is fitted with a safety device and refer to
Instruct and demonstrate the efficient and safe operation of the the Instructions for Use.
boiler, the heating system and if installed the domestic hot water
Advise the user of the precautions necessary to prevent damage
system.
to the system and building in the event of the heating system
Advise that to ensure the continued efficient and safe operation being out of use during frost or freezing conditions.
of the boiler it is recommended that it is checked and serviced
Reminder, leave these instructions and the  Benchmark logbook
as necessary at regular intervals. The frequency of servicing
with the user.
will depend upon the particular installation conditions and
usage, but in general once a year should be enough.
Draw attention, if applicable, to the current issue of the Gas
Safety (Installation and Use) Regulations, Section 35, which
imposes a duty of care on all persons who let out any property
containing a gas appliance.
It is the Law that any servicing must be carried out by a
competent person.
8 Servicing and Replacement of Parts
To ensure the continued efficient and safe operation of the THE GAS SUPPLY AND ISOLATE THE ELECTRICAL SUPPLY
boiler it is recommended that it is checked and serviced as TO THE BOILER.
necessary at regular intervals. The frequency of servicing will
AFTER COMPLETING A SERVICE OR REPLACEMENT OF
depend upon the particular installation conditions and usage,
GAS CARRYING COMPONENTS ALWAYS TEST FOR GAS
but in general once a year should be enough.
SOUNDNESS AND CARRY OUT FUNCTIONAL CHECKS ON
It is the Law that any servicing must be carried out by a CONTROLS.
competent person.
Unless stated otherwise replacement of parts is in the reverse
BEFORE SERVICING OR REPLACING PARTS TURN OFF order to removal.
13 221785B
5312
2158
8 Servicing and Replacement of Parts
It will be necessary to purge the pipework and multifunctional
8.1 Access
control before relighting, refer to Commissioning.
Refer to diagram 4.1 and 6.1.
8.5 Multifunctional Control/Solenoid
Slide the controls cover off. Undo the screws and remove the
outer case.
Replacement
Lift the combustion chamber shield clear of the lugs and
Refer to diagram 8.3.
remove.
Remove the multifunctional control cover as described in Section
8.4.
8.2 Main Burner
Disconnect electrical leads, remove the solenoid retaining clip
Refer to diagram 6.1.
and solenoid.
Remove the main burner. Lift the left hand end of the burner to
disengage the locating pin.
SECURING
Slide the burner off the injector by moving it to the left, take care
SUPPORT
SCREW (2)
not to damage the pilot burner and electrode assembly. Bring
BRACKET
the right-hand end of the burner through the opening first.
Service note: Clean the burner thoroughly, making sure that all
the flame ports are clear.
8.3 Boiler Flueway Cleaning
Gain access as Section 8.1. Remove burner as Section 8.2.
Refer to diagram 4.6 and 8.6.
Release split pin. Remove retaining angle and thermostat
phial.
Undo the screws and remove the flue cleaning door.
SAFETY
Remove flueway baffle.
DEVICE
LOCKNUT
Place a sheet of paper in the combustion chamber, covering the
electrode/pilot assembly, to catch the flue debris.
FLUE BLOCKAGE
Clean the boiler flueways and fins thoroughly with a suitable stiff
SAFETY DEVICE
brush.
HEX SCREW (4) GAS
Re-assembly note: When replacing the flue cleaning door and
SERVICE COCK
flueway baffle ensure they are fitted as shown in diagram 4.6.
'O' RING
BURNER
8.4 Multifunctional Control - Servicing/
SUPPLY
Replacement
PIPE
Gain access as Section 8.1.
Refer to diagram 6.4 and 8.1.
Remove multifunctional control cover securing screw.
Disconnect the electrical leads, thermocouple and pilot supply
MULTI-FUNCTIONAL
tube at the multifunctional control.
CONTROL
'O' RING
HEX
Remove the flue blockage safety device securing locknut and
SCREW (4)
MULTI-FUNCTIONAL
release from bracket, taking care not to strain the capillary.
CONTROL CONNECTIONS
Diagram 8.1
Remove the two securing screws from the support bracket.
Undo the four screws each side of the multifunctional control to
release the gas service cock and burner supply tube, take care
not to damage the  O rings. FINE INLET
SCREEN
Reassembly note 1: When refitting the gas valve take care not
to damage the  O rings.
PILOT
Reassembly note 2: When fitting a replacement gas valve FILTER
remove the bracket and fit to new one.
Refer to diagram 8.2.
To inspect the inlet screen and replace the pilot filter remove the
base of the multifunctional control by releasing the five screws.
When reassembling take care not to damage the screen.
Remake the electrical connections.
NOTE. Do not tighten the thermocouple nut more than one
MULTI-FUNCTIONAL
quarter turn beyond finger tight.
Diagram 8.2
CONTROL FILTERS
221785B 14
5313
2142
8 Servicing and Replacement of Parts
Ease the supply tube from the pilot injector and unscrew the
8.6 Main Injector
injector.
Gain access as Section 8.1.
8.9 Thermocouple
Remove main burner as Section 8.2.
Gain access as Section 8.1. Refer to diagram 6.4 and 8.4.
Remove the main burner injector from the right hand side of the
combustion chamber.
Disconnect thermocouple from the interrupter from the gas
valve.
Clean or replace as necessary. Do not clean with wire or sharp
instrument.
Disengage the thermocouple spring clip and remove the
thermocouple.
8.7 Electrode
Re-assembly note: When refitting do not tighten the
Gain access as Section 8.1. Refer to diagram 8.4.
thermocouple nut more than a quarter turn beyond finger tight.
Disconnect the electrode lead and remove electrode by undoing
8.10 Pilot Burner
the retaining nut.
Gain access as Section 8.1. Refer to diagram 6.3 and 8.4.
8.8 Pilot Burner Injector
Remove the main burner as described in Section 8.2.
Gain access as Section 8.1. Refer to diagram 8.4.
Remove electrode as described in Section 8.7.
Remove the electrode as Section 8.7.
Disengage the thermocouple spring clip and carefully ease the
Disconnect the pilot supply tube by unscrewing the pilot tubing
thermocouple from the pilot burner.
nut.
ELECTRICAL SOLENOID
CONNECTIIONS
SOLENOID
RETAINING
CLIP
SOLENOID
BRACKET
COVER
MULTI-FUNCTIONAL
MULTI-FUNCTIONAL
CONTROL
SOLENOID REMOVAL Diagram 8.3
NOTE: It is important that the thermostat is
SPARK fitted the same way as shown in the diagram
ELECTRODE
SPRING
SECURING
CLIP
NUT
THERMOSTAT
SECURING
SCREW (2)
TUBING NUT CONTROL
IGNITION
KNOB
LEAD
THERMOSTAT Diagram 8.5
Diagram 8.4
PILOT BURNER ASSEMBLY
15 221785B
5314
2159
8041
8 Servicing and Replacement of Parts
Disconnect the pilot supply tube by unscrewing the tubing nut.
8.14 Flue Blockage Safety Device
Remove the pilot burner by unscrewing the fixing at the left hand
Gain access as Section 8.1.
side.
Remove the flue cleaning door, refer diagram 4.6.
Reassembly Note: When refitting check that the spark gap is
correct and ensure that the thermocouple tip will be enveloped
Unscrew the two securing nuts and withdraw the phial assembly,
as shown in diagram 6.3.
see diagram 8.8.
Remove capillary from clips.
8.11 Thermostat
Remove the electrical connections from the safety device.
Gain access as Section 8.1. Refer to diagram 5.2, 8.5, 8.6 and
8.7.
Remove the locknut securing the safety device to the bracket
and withdraw the safety device.
Remove and temporarily support the electrical control box as
described in Section 5.1.
Remove the control knob. Remove the two electrical connections
from the thermostat body.
Release the thermostat body by unscrewing the two screws in
the front of the control box.
Remove the split pin. Withdraw the retaining angle and
thermostat phial from its pocket.
Remove the thermostat from the boiler.
CAPILLARY
Re-assembly note: When fitting the thermostat, make sure that
the thermostat is fully inserted into the phial pocket and then
insert the retaining angle. Replace the split pin.
Remake electrical connections.
Make sure that the capillary is positioned as before so that it
passes through the cut out in the control box, see diagram 8.5,
CONTROL
PIEZO
and that any excess being coiled up tidily at the rear of the
BOX
UNIT
control box. There must be no kinks or sharp bends in the
capillary.
Diagram 8.7
8.12 Peizo Unit
PIEZO UNIT
Gain access as Section 8.1. Refer to diagram 8.7.
Remove the electrical control box, refer to Section 5.1.
Disconnect the ignition lead at the piezo unit.
PHIAL
Note: To ease the removal of the piezo unit it is advisable to
temporarily remove the boiler thermostat from the control box,
refer to Section 8.11.
Depress the retaining tabs and remove the Piezo unit.
8.13 Ignition Lead
SECURING
Gain access as Sections 8.1 and 5.1.
SCREW (2)
Disconnect the lead at both ends and remove.
Re-assembly note: When replacing make sure the black end of
the lead is attached to the piezo unit.
SAFETY
DEVICE LOCKNUT
THERMOSTAT
CAPILLARY
PHIAL
RETAINING
ANGLE
RETAINING
SPLIT PIN
ELECTRICAL
PHIAL
CONNECTIONS
POCKET
FLUE BLOCKAGE
SECURING THE
SAFETY DEVICE Diagram 8.8
THERMOSTAT PHIAL Diagram 8.6
221785B 16
8039
5315
2171
9 Fault Finding
5291
PILOT WILL NOT LIGHT
START HERE
Does pilot stay alight when
Check flue blockage safety device
multi-functional control
has not operated,
knob is released?
check gas line-open all
cocks, rectify any blockages, purge
NO YES
out any air. Does pilot light?
NO
YES
PILOT SATISFACTORY
Apply match to pilot burner instead
of pressing piezo unit button.
Does pilot light?
NO
YES
Does pilot flame envelop
Undo tubing nut at pilot burner.
thermocouple?
Turn gas valve knob to Pilot/Ign.
Press multi-functional control knob.
NO
YES
Does gas flow freely?
YES
NO
Check aeration. If necessary - Clean
pilot, rectify blockage in pilot
injector, or replace.
Rectify blockage in pilot injector,
or renew pilot injector.
Check thermocouple circuit using
Undo tubing nut at pilot outlet
Thermocouple fault finding diagram.
of the multi-functional control.
Press gas valve knob.
Does gas flow freely?
YES
NO
On pressing piezo unit button is
there a spark across electrode
gap?
Change blocked pilot tube.
NO
YES
Pull ignition lead off electrode.
Hold end of lead close to pilot
burner and operate piezo unit.
Change multi-functional control. Is there a spark across gap?
NO
YES
Pull ignition lead off piezo unit.
Using blade of a screwdriver, touch
unit chassis and leave approx.
4mm gap from connection tag on
piezo unit. Operate piezo.
Is there a spark across gap?
NO
YES
Change Change
piezo unit. ignition lead.
Check electrode gap. Reposition,
or replace electrode as necessary.
BOILER PILOT FAULT-FINDING Diagram 9.1
17 221785B
9 Fault Finding
9.1 Pilot 9.4 Flue Blockage Safety Device
Refer to chart 9.1. If the device operates it indicates there is a problem with the
chimney. Make sure that the air vents are free from obstruction.
9.2 Thermocouple
Carryout spillage checks as Section 2.3.
Refer to chart and diagram 9.2.
9.3 Electrical
Refer to diagram 9.3 and 9.4.
The preliminary electrical system checks as contained in a
multimeter instruction book are the first checks to be carried out
during fault finding.
On completion of any fault finding task which has required the
breaking and remaking of electrical connections then the checks,
earth continuity, polarity and resistance to earth, must be
repeated.
2327/B
With the boiler cold, check connections of the thermocouple, boiler flue blockage safety device
and gas valve. Reset flue blockage safety device.
Disconnect flue blockage safety device connectors at points A and B at the gas valve,
see diagram Interrupter Electrical Connections.
Test continuity of the flue blockage safety device. Is there continuity?
NO
YES
Faulty boiler flue blockage
safety device, renew.
Re-connect boiler flue blockage
safety device to points A and B.
Disconnect thermocouple at
YES Faulty flue blockage safety device
connection point D of the gas valve.
connectors into gas valve,
Test continuity between point C and the
either at A or C.
body of the gas valve.
Renew where faulty.
Is there continuity?
NO
Test continuity of thermocouple between inner
NO
connection point D and point E.
Faulty thermocouple, renew.
Is there continuity?
YES
Thermocouple and boiler flue blockage
safety device circuit satisfactory.
THERMOCOUPLE FAULT FINDING Diagram 9.2
MULTI-FUNCTIONAL
CONTROL
PERMANENT
C NC
BLUE
L RED BROWN
LIVE
230V
3 4
N
50Hz
3A FUSE THERMOSTAT SOLENOID
Diagram 9.3
FUNCTIONAL FLOW WIRING
221785B 18
9008
9 Fault Finding
Carry out preliminary electrical checks to
make sure the electrical supply is available
at the boiler. Check that external controls
are calling for heat. Make sure that the
system is filled, the flue blockage safety
device is reset, the gas supply is available
and the pilot is lit.
Isolate electrical supply to the
control box.
Remove the control box cover and
check all cables.
Turn boiler thermostat to Max.
NO
Is there continuity between
'C' and 'NC'.
YES
Faulty thermostat.
Replace.
Turn boiler thermostat to 'O'.
NO
Is there open circuit between 'C'
and 'NC'.
YES
Restore electrical supply with pilot
NO
burner lit and boiler thermostat set
between 'MIN' and 'MAX', does the
main burner light.
YES
Faulty gas valve.
Replace.
NO
Turn boiler thermostat to "O'.
Does main burner extinguish.
YES
Boiler controls in order.
FAULT FINDING Diagram 9.4
19 221785B
0899/A
10 Replacement Parts
If replacement parts are required, apply to your local supplier. Please quote the name of the appliance and its serial number, found
on the data label on the right hand side of the control box, after removal of the cover.
1
4
5
3
2 7
13
12
9
14 10
8
6
11
Diagram 10.1
Key No Part No Description G.C. Part No.
1 429549 Multifunctional control 312 926
2 208040  O ring - gas valve 334 592
3 FF2029 Injector 355 274
4 K2674 Thermocouple 390 894
5 K3580 Clip - thermocouple 390 983
6 203416 Pilot burner 381 793
7 900500 Spark electrode 381 733
8 WW4617 Ignition lead 312 997
9 202519 Thermostat 381 798
10 204687 Control knob
11 202713 Piezo unit
12 801236 Mica window and foil gasket
13 203350 Solenoid
14 800755 Safety device 278 469
Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.
221785B 20
8053


Wyszukiwarka

Podobne podstrony:
Glow Worm installation and service manual Ultimate 60CF UIS
Glow Worm installation and service manual Ultimate 60BF UIS
Glow Worm installation and service manual Ultimate 50CF UIS
Glow Worm installation and service manual Ultimate 40BF UIS
Glow Worm installation and service manual Ultimate 50BF UIS
Glow Worm installation and service manual Ultimate 30BF UIS
Glow Worm installation and service manual Hideaway 40CF
Glow Worm installation and service manual Hideaway 60CF UIS
Glow Worm installation and service manual Hideaway 100CF UIS
Glow Worm installation and service manual Hideaway 50BF UIS
Glow Worm installation and service manual Hideaway 80CF UIS
Glow Worm installation and service manual Hideaway 80BF UIS
Glow Worm installation and service manual Miami GF UIS
Glow Worm installation and service manual Hideaway 70CF UIS
Glow Worm installation and service manual Hideaway 70BF UIS
Glow Worm installation and service manual Hideaway 40BF UIS
Glow Worm installation and service manual Hideaway 120BF UIS
Glow Worm installation and service manual Hideaway 120CF UIS
Glow Worm installation and service manual Energy Saver 40 UI

więcej podobnych podstron