Okuma OSP 5000 LC10 L235 85 1


{Change Comments ***********************************************************}

{8/16/95,
Updated for Catalyst v2.20 per Fanuc 10T MS [-] L001.85.01 Format.
DWB}

{4/7/97, added Y and J format to Default formats. MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '+####.####;0'
#3 = '#######0'
#4 = '###.##;0'
#5 = '####.####;0'
#6 = '###0'
#7 = '#'
#8 = '00' { See TurretToolID sub }

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(MUL#,2) { Non-Canned Threading AutoFinish }
FORMAT(XCutDepth#,2)
FORMAT(ZCutDepth#,2)
FORMAT(Recall#,3)
FORMAT(ToolOffset#,3)
FORMAT(ToolLess20#,3)
FORMAT(ToolOffsetLess20#,3)
FORMAT(Program#,3) {.72}
FORMAT(Operation#,3) {.72}
FORMAT(Tool#,3) {.72}
FORMAT(Dwell#,4) {.72}
FORMAT(Peck#,5)
FORMAT(CalcEPRPM#,6)
FORMAT(RapidF#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

Tab:
' '
RETURN

TurretHome:
SeqLabC 'X30.Z30.' EOL
RETURN

SetTurret:
Save# Num#('1') Tool#
Save# Num#('2') ToolOffset#
IF GreaterThan? Tool# Num#('20')
Save# Num#('1') SUB# Recall# Num#('1') Num#('20')
Save# Num#('2') SUB# Recall# Num#('2') Num#('20')
END
IF FirstOperation? { Send Turrets Home }
SeqLabC 'G13' EOL
Rapid TurretHome
SeqLabC 'G14' EOL
Rapid TurretHome
END
RETURN

TurretSequence:
IF GreaterThan? Tool# Num#('20')
'Ś2' Recall# Num#('1') '00' EOL
SeqLab
IF FirstOperation?
SeqLabC 'G14' EOL
ELSE { NewTool }
IF LTEqual? LAST Tool# Num#('20')
SeqLabC 'G14' EOL
END
END
ELSE
'Ś1' Recall# Num#('1') '00' EOL
SeqLab
IF FirstOperation?
SeqLabC 'G13' EOL
ELSE { NewTool }
IF GreaterThan? LAST Tool# Num#('20')
SeqLabC 'G13' EOL
END
END
END
RETURN

TurretToolID:
FORMAT(Recall#,8)
'T' Recall# Num#('2') Recall# Num#('1') Recall# Num#('2')
FORMAT(Recall#,3)
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TURRET '
IF GreaterThan? Tool# Num#('20')
'B'
ELSE
'A'
END
' TOOL ' Recall# Num#('1') ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags from last Op, .70}
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN

FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN

FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN

ApproachSP:
IF ApproachFace?
SeqLabC StockOnNoCan XSPC EOL
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqLabC FeedNoCan ZSPC FeedRateNoCan EOL
END
ELSE { ODApproach/IDApproach }
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
END
RETURN

AppMove:
StockOff ThisOpEntryZCP
RETURN

Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqLabC ThisOpEntryXCP AppMove EOL
ELSE
IF ApproachID?
SeqLabC XOpCD AppMove EOL
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP AppMove EOL
END
END
ApproachSP
RETURN

CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
CSSOff
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
ELSE
SeqLabC Preset MaxRPM EOL
END
END
SeqLabC
IF NewToolOffset?
SetTurret
TurretToolID
END
IF LAST ProgStop?
Tab CoolOn
ELSE
IF NOT CoolOff? AND LAST CoolOff?
Tab CoolOn
END
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF LAST ProgStop?
Tab CSSOn 'G96' Tab Speed
ELSE
IF NotEqual? SpeedRPM# LAST SpeedRPM#
Tab CSSOn 'G96' Tab Speed
END
END
ELSE
Tab CSSOn 'G96' Tab Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
Tab 'G97' Tab Speed
ELSE
IF LAST ProgStop?
Tab 'G97' Tab Speed
ELSE
IF NotEqual? SpeedRPM# LAST SpeedRPM#
Tab 'G97' Tab Speed
END
END
END
END
IF LAST ProgStop?
SpinOn
END
EOL
DoPostScript
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
IF NOT LastFeat?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN

ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G33' MoveXC MoveZC
IF Taper?
XTapAtZ
END
ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN

CheckRapid:
CRCOffC RapidC
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
TagInit
SetAbsOrInc
PosSideLathe
StandardXZArcs
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
IF UseComments?
IF ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
END
RestoreScale
OpenSub
StockOff {.71.2}
SetHome
SetTurret
DoOpComments
DoPostScript
Plane
TurretSequence
IF ConstantSurfaceFeed?
SeqLabC Preset MaxRPM EOL
END
SeqLabC TurretToolID Tab CoolOn Tab
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Tab Speed SpinOn EOL
Approach
ELSE
IF NewTool?

{Finish off last Operation}

StockOff {.62}
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC EOL
DoEndOpPS
TurretHome
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END

{Start new Operation}

SetTurret
DoOpComments
DoPostScript
TurretSequence
IF ConstantSurfaceFeed?
SeqLabC Preset MaxRPM EOL
END
SeqLabC TurretToolID Tab CoolOn Tab
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Tab Speed SpinOn EOL
Approach
ELSE
IF SameTool? {.62}

{Start new Operation}

StockOff
DoOpComments
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
END
END
CheckOffset
ApproachSP
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF NOT RoughSimple?
TagInc
SetPass2
IF RoughContour?
SeqLabC 'G85NLAP' Tag# Tab CutDepth FeedRate XStkLeft ZStkLeft EOL
'NLAP' Tag# Tab LCycle EOL
ELSE
IF RoughPatternShift?
SeqLabC LCycle 'NLAP' Tag# Tab 'D'
IF ApproachFace?
ZCutDepth#
ELSE
XCutDepth#
END
FeedRate XStkLeft ZStkLeft EOL
'NLAP' Tag# Tab
IF ApproachFace?
'G82'
ELSE
'G81'
END
EOL
END
END
SeqLabC StepMove StrtPos EOL
ToolPath
SeqLabC 'G80' EOL
IF AutoFinish?
SeqLabC 'G87NLAP' Tag# EOL
END
SetAbs
SetPass1
TrackXNO# CycleStartX#
TrackZNO# CycleStartZ#
SetAbsOrInc
END
ELSE
IF Threading?

{ Face Threads require G72, ZTapAtX and W Address for XTapAtZ }

SeqLabC LCycle XatFinZ FinZ XTapAtZ
IF SingleEdgeCut?
ToolAngle
ELSE
'B0'
END
CutDepth ThrdHeight ThrdLead 'M32'
IF ConstantVolumeCut?
'M75'
ELSE
'M74'
END
IF Chamfer?
'M23'
ELSE
'M22'
END
EOL
IF AutoFinish?
SeqLabC 'G33' XatFinZ FinZ
IF Taper?
XTapAtZ
END
ThrdLead EOL
END
ELSE
IF Drilling?
SeqLabC
IF Tap? AND NOT CWSpindle?
'G78'
ELSE
LCycle
END
XCSP ZDepth Peck Retract
IF PeckFullRetract?
'L' Peck#
END
FeedRate Dwell EOL
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish? { .82.1c }
StockOff
IF Turning?
IF ApproachFace?
SeqLabC RapidC ZOpECPC EOL
ELSE
SeqLabC RapidC XOpECDC EOL
END
ApproachSP
SeqLabC StockOff StrtPosC EOL
ToolPath
ELSE
IF Roughing? AND NOT RoughSimple?
SetPass2
SeqLabC RapidC XSPC ZSPC EOL
SeqLabC StockOff StrtPosC EOL
ToolPath
SetPass1
ELSE
IF Threading?
SeqLabC 'X' MUL# Num#('2') ADD# FinishXRadius# Taper# EOL
SeqLabC 'G33'
IF Taper?
XatFinZ
END
FinZ
IF Taper?
XTapAtZ
END
ThrdLead EOL
SeqLabC Rapid XSP EOL
SeqLabC ZSP EOL
END
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
StockOff
CRCOffC RapidC
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC EOL
DoEndOpPS
TurretHome
IF ProgStop?
SeqLabC 'M0' EOL
END
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END


Wyszukiwarka

Podobne podstrony:
Okuma OSP 5000 LC10 L235 82 2
Okuma OSP 5000 [NC] L606 85 1
Okuma OSP 5020L [PB] L604 85 1
Okuma OSP 5020 [TPM] L572 85
Okuma OSP 5020L [CP] L787 85
Okuma OSP 7000L [JDHW] L707 85 1m
Okuma OSP 3000 LC10 L069 82 1
Okuma OSP 3000 LC20 L049 85
Okuma OSP 5020L [WMC] L676 85 3
Okuma OSP 5000 LB10 L351 82 2
Okuma OSP 5500 Cadet L331 85
Okuma OSP 5020L [GCS] L540 85

więcej podobnych podstron