{
MILL=F
LATHE=T
SIMPLE_ROT_POS=F
ROTARY_MILL=F
ADV_MILL=F
SUBS=F
MILLTURN_Y-AXIS=F
METRIC=F
}
{Change Comments ***********************************************************}
{8/23/91
Copied & modified: HiTec-Turn HS L024.82
For: Machine Specialties
Control: Yasnac LX3
Machine: HiTech 20 & 25
Added GetSequence sub to output 'Åš' Tool# '00' for FirstOperation and NewTool.
Changed NegSideLathe to PosSideLathe.
Changed ReverseXZArcs to StandardXZArcs.
Turning ConstantSurfaceFeed on at Home.
Added Preset 'S3500' at FirstOperation.
Deleted CalcRPM1 at FirstOperation and NewTool, always using Speed.
Deleted CalcRPM2 at NewTool.
Deleted ConstantSurfaceFeed logic at CommonPoint.
Deleted CalcEPRPM# at end of Program, and FORMAT for same.
Deleted all Offset support.
Deleted OpToolID LatheOffset at AppMove sub.
Deleted IF NewToolOffset logic at CheckOffset sub.
Moved OpToolID '00' to line by itself at FirstOperation and NewTool.
Deleted LOfstOff '00' at NewTool.
Deleted OpToolID '00' at end of Prog.
Moved CoolOn from AppMove sub to FirstOperation and NewTool and added literal '/'.
Modified StartUp Output at FirstOperation.
Added blank line at FirstOperation, NewTool and end of Prog.
Modified Canned Thread Cycle based on settings of ConstantVolumeCut and SingleEdgeCut radio buttons.
Deleted CutMethod Command from Canned Thread Cycle Block.
Moved FirstHome to CoolOff block at end of Prog.
Added literal 'M0' at end of prog.
Changed EOP Command to literal 'M99P100' at end of Prog.
JR}
{7/15/92
Modified: Yasnac LX3 HS 20/25 L234.82
For: Machine Specialties
Changes made per Joseph Landry and Bob Shumaker at Machine Specialties.
Updated to Version 4.1 per Fanuc 10T MS [-] L001.82 Format.
Deleted AppMove Sub.
Modified Approach Sub to bypass Move to XCP and/or ZCP when coming from ToolChng Position.
Changed literal '/' to SetLineStrtChr(/) for CoolOn at FirstOperation, NewTool and CheckOffset sub.
Modified ContourRough StrtPos.
Control does not allow for Multi-Axis StrtPos.
Turning Cycle needs XCSP block followed by ZCSP block.
Facing Cycle needs ZCSP block followed by XCSP block.
Added Canned PeckFullRetract Cycle.
Modified Canned PeckChipBreaker Cycle.
Both Cycles are identicle except that PeckFullRetract has RLevel, PeckChipBreaker doesn't.
DWB}
{8/26/95, Updated Yasnac LX3 HS 20/25 L234.82.1 to .85 format per Fanuc 10T MS [-] L001.85.01.01, JR}
{8 Oct98
Original: Yasnac LX3 HS 20/25 L234.85
Created: Yasnac LX3 HS [M3] Lxxx.85
For: MIL-3
Changes made per: Kevin Elliot
Added Post Header Comment at the top of Prog.
Deleted old version numbers and comments e.g. {.62}, {commands}, {literals}, etc
Deleted GetSequence from FirstOperation and NewTool
Moved ToolTypeComment from DoOpComments to FirstOperation and NewTool
Added OpToolID LatheOffset to AppMove
Changed IF CannedCycle? Boolean in ToolPath from SeqLab to 'N' Operation# '02'
Deleted 'T0100', Rapid Home and ProgStop from FirstOPeration
Added CSS Boolean handle MaxRPM Output in FirstOperation and NewTool
Deleted GetSequence Line numbering and replaced with Line numbers based on the Operation Number
Note: This post is configured for Minimize Sequencing
Deleted Blank lines between operations and at the End od Prog
Deleted SetLineStrtChr('/') in FirstOperation and NewTool
Deleted 'PÅ‚' Tag# and 'Q²' Tag# from RoughContour and RoughPatternShift Cycles and replaced with custom
line numbering based on the Operation Number
Deleted CoolOff, SpinOff, Untool, ProgStop and 'M99P100' at the End of Prog
Added EOP at the End of Prog
Charles Winston}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.####;0.'
#3 = '#######0'
#4 = '###^##0'
#5 = '#.######;0.'
#6 = '#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(MUL#,2) { Non-Canned Threading AutoFinish }
FORMAT(InFeedAngle#,2)
FORMAT(FirstMoveEPX#,2)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Program#,3)
FORMAT(Operation#,3)
FORMAT(Tool#,3)
FORMAT(Dwell#,4)
FORMAT(FeedIPR#,5)
FORMAT(RapidF#,6)
{Prog Subroutines **********************************************************}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN
PSInit: {reset flags from last Op, .70}
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL
PSStuff
NextPS
RETURN
StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN
FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN
FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN
ApproachSP:
IF ApproachFace?
SeqLabC StockOnNoCan XSPC EOL
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqLabC FeedNoCan ZSPC FeedRateNoCan EOL
END
ELSE { ODApproach/IDApproach }
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
END
RETURN
AppMove:
StockOff ThisOpEntryZCP OpToolID LatheOffset
RETURN
Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqLabC ThisOpEntryXCP AppMove EOL
ELSE
IF ApproachID?
SeqLabC XOpCD AppMove EOL
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP AppMove EOL
END
END
ApproachSP
RETURN
CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
IF NewToolOffset?
{ not using tool offsets }
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SeqLabC Speed
END
ELSE
SeqLabC Preset MaxRPM EOL
SeqLabC CSSOn 'G96' Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
SeqLabC CSSOff 'G97' Speed
END
END
IF LAST ProgStop?
SeqLabC SpeedC SpinOn EOL
SetLineStrtChr('/')
SeqLabC CoolOn EOL
SetLineStrtChr('')
ELSE
SeqLabC SpeedC EOL
IF NOT CoolOff? AND LAST CoolOff?
SetLineStrtChr('/')
SeqLabC CoolOn EOL
SetLineStrtChr('')
END
END
DoPostScript
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC:
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
IF NOT LastFeat?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN
ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
ELSE
IF CannedCycle?
'N' Operation# '02'
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN
CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
RapidC
END
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
SetAbs
PosSideLathe
StandardXZArcs
SetMaxRPM('1800')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
END
RestoreScale
OpenSub
StockOff
SetHome
IF ConstantSurfaceFeed?
SeqLabC Preset MaxRPM EOL
ELSE
SeqLabC Preset 'S1800' EOL
END
DoOpComments
DoPostScript
Plane
'N' Operation# OpToolID '00'
IF UseComments?
SetScale('1')
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )'
END
RestoreScale
END
'/M8' EOL
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
SeqLabC Speed SpinOn EOL
Approach
ELSE
IF NewTool?
{Finish off last Operation}
StockOff
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC EOL
DoEndOpPS
SeqLabC NewHome EOL
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END
{Start new Operation}
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
ELSE
SeqLabC Preset MaxRPM EOL
END
END
DoOpComments
DoPostScript
'N' Operation# OpToolID '00'
IF UseComments?
SetScale('1')
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )'
END
RestoreScale
END
'/M8' EOL
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
SeqLabC Speed SpinOn EOL
Approach
ELSE
IF SameTool?
{Start new Operation}
StockOff
DoOpComments
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
END
END
CheckOffset
ApproachSP
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
IF ApproachFace?
SeqLabC LCycle 'Z' FirstMoveEPZ# XatFinZ XTapAtZ FeedRate EOL
ELSE
SeqLabC LCycle XatFinZ FinZ XTapAtZ FeedRate EOL
END
SimpleRough
ELSE
IF RoughContour?
SetPass2
SeqLabC LCycle 'P' Operation# '01Q' Operation# '02' XStkLeft ZStkLeft CutDepth FeedRate EOL
IF ApproachFace?
'N' Operation# '01' StepMove ZCSP EOL
SeqLabC XCSP EOL
ELSE
'N' Operation# '01' StepMove XCSP EOL
SeqLabC ZCSP EOL
END
ToolPath
IF AutoFinish?
SeqLabC 'G70' 'P' Operation# '01Q' Operation# '02' EOL
END
ELSE
IF RoughPatternShift?
SetPass2
SeqLabC LCycle 'P' Operation# '01Q' Operation# '02' XStkLeft ZStkLeft XminusU ZminusW NumCuts FeedRate EOL
'N' Operation# '01' Rapid StrtPos EOL
ToolPath
IF AutoFinish?
SeqLabC 'G70' 'P' Operation# '01Q' Operation# '02' EOL
END
END
END
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
IF NOT ConstantVolumeCut? AND NOT SingleEdgeCut?
SeqLabC 'G92X' FirstMoveEPX# FinZ ThrdLead EOL
SimpleRough
ELSE
SeqLabC LCycle XatFinZ FinZ XTapAtZ ThrdHeight CutDepth ThrdLead
IF ConstantVolumeCut? AND NOT SingleEdgeCut?
'A0'
ELSE
'A' InFeedAngle#
END
EOL
END
IF AutoFinish?
SeqLabC Feed XatFinZ EOL
SeqLabC 'G32' FinZ ThrdLead EOL
SeqLabC Rapid XCSP EOL
SeqLabC ZCSP EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF Peck?
SeqLabC LCycle ZDepth Peck FeedRate
IF PeckFullRetract?
RLevel
END
EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
ELSE
IF Grooving?
StockOn
SetPass1
SeqLabC StrtPos EOL
ToolPath
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish? { .82.1c }
StockOff
IF Turning?
IF ApproachFace?
SeqLabC RapidC ZOpECPC EOL
ELSE
SeqLabC RapidC XOpECDC EOL
END
ApproachSP
SeqLabC StockOff StrtPosC EOL
ToolPath
ELSE
IF Roughing? AND NOT RoughSimple?
SetPass2
SeqLabC RapidC XSPC ZSPC EOL
SeqLabC StockOff StrtPosC EOL
ToolPath
SetPass1
ELSE
IF Threading?
SeqLabC 'X' MUL# Num#('2') ADD# FinishXRadius# Taper# EOL
SeqLabC 'G32'
IF Taper?
XatFinZ
END
FinZ ThrdLead EOL
SeqLabC Rapid XSP EOL
SeqLabC ZSP EOL
END
END
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}
{End of program ************************************************************}
{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
RapidC
END
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC EOL
DoEndOpPS
SeqLabC FirstHome EOL
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
Wyszukiwarka
Podobne podstrony:
Yasnac LX3 MS [MT] L719 85Yasnac LX3 HS 20 25 EB L469 85mYasnac LX3 MS [PMP] L157 85Yasnac LX2 HS TPS L099 85Yasnac I80 HS [HA] L765 85 1Yasnac LX3 MS [FTM ] L600 85 3Yasnac LX3 MS [HA2] L376 85Yasnac LX3 MS [HT] L307 85Yasnac LX3 MS [FTM] L452 85 4Yasnac LX3 KIA [FP] L673 85Yasnac LX3 MS [WI] L411 85 3Yasnac LX3 MS SL 25 L277 85Yasnac LX1 HS L011 85Yasnac LX1 HS (r) L210 85więcej podobnych podstron