Shaker-Style Bed
he Shakers lived their lives ly high off the ground to keep out of
apart from the  world, what the cold drafts near the floor.
T
they called life outside their religious This bed is not a copy of a particular
communities. They did a lot of things Shaker bed. Instead, I have borrowed
differently from the  world, including
elements from a number of Shaker beds
sleep. Because the Shakers were celi-
I have seen. Some of my construction
bate, they had little need for double
details remain faithful to traditional
beds and used them only to save
Shaker construction. But I have made
space. Two men, women, or children
concessions to modern living and to
would sleep together in these.
contemporary woodworking techniques.
Many Shaker-designed single beds
I chose to make this a full-size bed,
did not break down. The side rails
which is more useful than the 28-in.-
were tenoned into the legs just like
to 34-in.-wide and 70-in.- to 72-in.-
the headboards and footboards.
long originals. I also omitted the
Almost all of the beds had casters on
casters. I hesitate to say that these
the legs. This made it easy to move
changes make the bed better, but they
the bed out of the way when sweeping
certainly make it more familiar and
the floors. The beds were also relative-
comfortable for us today.
37
Shaker-Style Bed
THE BASIC STRUCTURE of the Shaker-Style Bed
is similar to the First Bed. However, the legs are
turned, the headboard and footboard planks do
double duty as structural rails, and the cleats are
integral with the side rail design.
Square
section
Headboard
Side rail
Slats
Rail
OTHER BED SIZES
Cleat
Headboard Footboard
height in center height in center
Twin* 181D 2 123D 4
Queen 22 141D 4
* For a twin bed, shorten the headboard square
Bolt hole
section to 141D 2 and make the height of the
cover
headboard 131D 4 where it meets the leg.
Note: A king-size Shaker-Style Bed is not recommended.
38 S HAKER- S TYLE B ED
HEADBOARD DETAILS
Headboard leg
32
HEADBOARD END OF SIDE RAIL
Shallow
mortise
3
1 20 D 4
1 D 4
1
3
Headboard (1 D 16 thick)
D 8 bolt
3
14 D 4
5
hole
3
6 D 4
12
3
1
2 D 2
1
1
1 D 8
Rails are
3
1 53 D 16 to opposite leg
1 D 16 thick.
5
15 D 8
The overall length of the headboard and
3
footboard planks (including tenons) is 56 D 8 .
FOOTBOARD DETAILS
2
Footboard
This curve is a section of an
ellipse with a minor diameter of
18 and a major diameter of 58 .
5
26
13 D 8
3
1 8 D 4
Footboard (1 D 16 thick)
1
1 D 8
3
53 D 16 to opposite leg
FOOTBOARD END OF SIDE RAIL
WOODEN BOLT HOLE COVER
10
12
3
Chamfer
3
4 D 8
3
1 D 4
3
1
Footboard leg
Cleat
1
1 D 4
S HAKER- S TYLE B ED 39
Building the Bed Step-by-Step
LTHOUGH THIS BED looks very dif-
CUT LIST FOR SHAKER BED
Aferent from the First Bed on pp. 18-35,
the overall approach to building it is the
Headboard and Footboard
same. To start, you work on the headboard
1 Headboard plank 11D 16 in. x 203D 4 in. x 563D 8 in.
and footboard together. Then move on to the
1 Footboard plank 11D 16 in. x 135D 8 in. x 563D 8 in.
side rails and finally the mattress support. The
turned legs are not essential to the construc-
2 Headboard posts 2 in. x 2 in. x 321D 4 in.
tion, but they are to the design. You can make
2 Footboard posts 2 in. x 2 in. x 261D 4 in.
the bed with straight or tapered legs, but it
won t look as nice.
Side Rails
2 Side rails 11D 16 in. x 3 in. x 761D 2 in.
2 Ogees for headboard ends 11D 16 in. x 5 in. x 12 in.
Making the
2 Ogees for footboard ends 11D 16 in. x 3 in. x 10 in. Headboard and
Footboard
2 Cleats 1 in. x 25D 16 in. x 76 in.
3
15 Slats D 4 in. x 4 in. x 541D 8 in.
Milling the headboard and
Hardware
footboard planks
5 1. Mill up the pieces for the headboard and
30 Dowels (for slat pins) D 16 in. x 11D 2 in.
footboard planks.
4 Hex-head bolts with nuts and washers
2. If you re not working with a single board
4 Bolt hole covers 11D 4 in. x 13D 4 in. x 1D 4 in. thick
plank, glue the pieces into slightly oversize
planks.
#6 x 15D 8-in. screws, as needed
3. Cut the planks to size, making sure the
#6 x 3D 4-in. roundhead brass screws, as needed
edges are parallel and the ends square.
These dimensions are for a full-size bed with a mattress up to 8 in. thick. You
Cutting the tenons
may have to adjust your dimensions to suit the bed size, the mattress size, or
any differences in wood dimensions.
This bed doesn t have a separate headboard
and footboard rail to provide structural
strength, so the planks themselves need struc-
tural tenons. However, 8-in.- to 14-in.-wide
mortise-and-tenon joints would break apart
Tip: The moisture in yellow glue
due to seasonal wood movement. The tradi-
swells wood slightly along joint edges.
tional solution is to make a divided tenon (see
Wait 24 hours before smoothing the
 Headboard and Footboard Joinery on p. 42).
surfaces to give the moisture a chance
to evaporate and the wood to settle 1. Cut the headboard and footboard plank
tenon shoulders with the tenoning jig
back down.
described in  A Tenoning Jig on p. 24 and a
4-in.-long straight bit. To use the jig with the
wide headboard, remove the vertical fence
from the workpiece support. You ll have to cut
the tenons a portion at a time (see photo A).
40 S HAKER- S TYLE B ED
Photo A: One good
way to cut the full-
2. Lay out the sections of tenon that will stay 3. Clean up the sawn edge with a plane or
width tenons on the
full length and the short 1D 4-in. haunches. sandpaper.
headboard and foot-
3. Cut away the waste on the bandsaw and
board is with the
Cutting the leg joinery
then pare away all of the haunch tenon on the
tenoning jig on
very top and bottom to leave shoulders. 1. Mill up the leg blanks. The cut list dimen-
p. 24 and a 4-in.-
sions are 1D 4 in. longer than finished. The extra
long router bit.
1
Laying out and cutting the
D 4 in. on the top of the legs is for the turning
curve on top of the planks centers on the lathe you ll cut it off and
The headboard and footboard on this bed smooth it to shape later.
have elliptical curves. If you re unfamiliar 2. Lay out the mortises for the headboard,
with ellipse layout, see  An Ellipse Layout Jig footboard, and side rails as shown in
on p. 117. You can also use a simple curve as  Headboard and Footboard Joinery on p. 42.
for the First Bed. Remember that the left and right legs are not
identical, though they are symmetrical.
1. Lay out either a simple curve or an ellipse 3. Mark lines that indicate the end of the sec-
along the top edge of the board. tions that remain square all the way across the
2. Cut the curve out on the bandsaw, keeping
to the outside of the line.
S HAKER- S TYLE B ED 41
Headboard and Footboard Joinery
Double tenons are the traditional way to join a wide headboard to legs. Wood movement may
still cause cracking because the overall movement of the plank is still constrained. But the
joints should remain structurally sound. To minimize cracking, make sure the wood is very dry.
The haunches are not glued and help keep the headboard from warping.
HEADBOARD LEG BLANK AND TENON
FOOTBOARD LEG BLANK AND TENON
5
1 D 8 deep
mortise
1
D 2
1
D 2
5
D 8
1
Headboard
26 D 4
23D 4
Footboard
1
2 D 2
1
2 D 2
3 2 3
8 D 4
5
1
32 D 4
3 3
1
14 D 4 1
1 2 D 2
2 D 2
2 D 2
1
D 4
1
2 D 2
3
7
3
3
2 D 4
1
19
13 D 8
1 D 32
1
1
13 D 2
2 D 2
12
1
13 D 8
1
13 D 2
12
42 S HAKER- S TYLE B ED
Alternative Joinery
For Headboard And Footboard
The headboard and footboard planks are structural on The disadvantage of this technique is that the joint
this bed. While the traditional construction method is a may not keep the headboard plank as tight against the
divided tenon, wood movement may cause cracking legs. It also offers less glue surface (and strength) than
because the overall movement of the plank is still con- the divided tenons. Using fat haunches (shallow tenons,
strained. An alternative method is to use a single tenon really) without glue to either side of the tenon helps keep
in the center. This design allows for unconstrained move- the headboard from warping.
ment and little chance of cracking.
HEADBOARD FOOTBOARD
5
2
4 3
4 D 4
3
1 D 4
3
Footboard
Headboard
5
3 3
2
3 8 D 4
14 D 4
4
3
1 D 4
3
4 D 4
3
3
8 D 4
8 D 4
blank at the top and bottom. You need these 5. Also cut the headboard and footboard mor-
marks when turning. tises 9D 32 in. deep over their full length. Then
4. Cut the side rail mortises 9D 32 in. deep, just go back and cut the two full-depth mortises
deep enough to keep the rail from twisting 15D 8 in. deep.
or moving down. The best tools for the job 6. Drill the 3D 4-in.-diameter, 3D 8-in.-deep coun-
are a plunge router and the mortising block terbore for the bed bolts on the outside of
described in  Mortising Jig for Routing Small each leg.
Workpieces on p. 23.
S HAKER- S TYLE B ED 43
7. Drill the 5D 16-in. holes for the 51D 2-in. hex- 4. Rough out the top and bottom of the
Tip: Use wood with
head bed bolts through the legs, centered in blank into cylinders with a roughing gouge,
straight, even grain
the counterbore. To ensure that the bolt hole staying about 1D 2 in. away from the edges of
for the legs. You
is straight, drill in from both sides and meet the square section.
don t want much
in the middle. It s the long way around to do 5. Clean up the transition between cylinder
grain runout on the
it, but it ensures a good result. and square section using a gouge, working
relatively long and
slowly to the line. Start the cut with the tool
thin legs because it
Turning the legs
up on edge, then roll the gouge flatter toward
will weaken them
1. Make up full-scale patterns of the upper the bottom of the cut, keeping the bevel rub-
and lower parts of the turnings on pieces of bing against the spinning leg (see photo B on
considerably.
1
D 4-in. plywood, 21D 2 in. wide and as long as the p. 46). If you just present the tool flat (like a
section involved (see  Making the Turning scraping tool), you re likely to tear a chunk
Pattern ). off the edges of the square section.
2. Set up the blank in the lathe. 6. Using a pencil, transfer the notch locations
3. Set the tool rest in position for roughing from the pattern to the spinning blank (see
out the cylindrical lower leg. Rotate the leg photo C on p. 46).
blank by hand to check that the tool rest 7. Using a parting tool, turn notches in the
won t interfere with the blank when it s blank where you have marked it to the vari-
spinning. ous diameters (see  Leg Turning Strategy ).
Note that you don t do this on every line you
Making the Turning Pattern
Plywood patterns with notches to hold the tip of a pencil help you
mark the turning blank accurately while it s spinning in the lathe.
FOR BELOW THE SQUARE SECTION
Brad to register
MAKING THE
bottom of turning
PATTERN
blank 1
Notches for point
D 4 plywood
of pencil
1. Draw the profiles of
the turning on the
plywood. Either
sketch it out by hand
or trace an enlarged
photocopy.
2. Draw perpendicular
11D 32
lines out to one
11D 2
19D 16 17D 8
17D 8
edge of the pattern.
11D 4
11D 4
1 
These will later serve
as depth-of-cut and
turning-detail guides.
3. At each of these
FOR ABOVE THE SQUARE SECTION
lines, cut a shallow
notch with a knife or
a saw, just big
Brad to register
enough to hold a
from the top of
pencil point.
the turning blank
4. Mark the diameter
of the leg at each of
Cut away the corner
the indicated points
to prevent tearout on
11D 32
on the pattern.
the square section
113D 16
11D 8
when the pattern is in
use.
44 S HAKER- S TYLE B ED
marked. Some of the lines indicate the loca- edges of the transition between square section
Tip: The marks you
tion of a change from one detail to another, and turning. A good technique is to wrap a
put on the ends of
and you ll have to turn next to them. On 1-in. dowel with sandpaper and work it over
the pommel should
others, such as the sides of the bead below the transition while holding on with two
be easily visible
the square section, you can t get a parting hands (see photo F on p. 47).
when the blank is
tool or calipers into the small space. Size 13. Burnish the smooth turning with a hand-
spinning.
these by eye. ful of clean shavings (see photo G on p. 48).
8. Where you can, set your calipers for each 14. Saw off the waste at the very top of the
desired diameter and reduce the blank with leg above the finial. Then sand to complete
the parting tool until the calipers just fit over the shape.
the leg at that point (see photo D on p. 46). 15. Smooth the faces of the square sections.
9. Connect the grooves with the parting tool, Because it s important to keep the faces per-
following the shape on the pattern. Use what- fectly flat, use a well-tuned handplane. A
ever turning tools you prefer (see photo E on sanding block that doesn't overhang the edges
p. 47). Watch the flow of the curves and the will also do a good job, though it s more likely
overall shape of the leg to make sure you are to round over the edges.
doing what you want. Correct any problems
Assembling the headboard
with a gentle touch.
10. Leave a little pad of wood under the bot- and footboard
tom bead for the tailstock to bite into. You 1. Fit the headboard joints using a shoulder
can remove the pad later and replace it with a plane to trim the tenons to size (see photo H
furniture glide, or you can just leave it. on p. 48). Strive for a snug fit. The joint
11. Add definition to the turning by touching should go together with some effort, but
the sharp tip of a skew chisel to the transition heavy hammering should not be necessary.
points. Just a touch will do it. 2. Glue up the headboard and footboard.
12. Sand the spinning blank with the coarsest Spread glue only in the deep mortises; the
grit necessary, working your way up through haunches get no glue at all. You ll need at
400 grit. Be careful not to sand away the crisp least two clamps to get the legs tight to the
LEG TURNING STRATEGY
Use the patterns to reduce the diameter of the turning blank to the desired dimension
in a few select places. This will allow you to envision the final leg shape as you turn by  connecting the dots,
and help you make duplicates accurately.
Cut the notches with a parting tool.
Cut in with a skew chisel. (No room for parting tool.)
S HAKER- S TYLE B ED 45
Photo B: After
roughing out the
cylinder below the
joinery block, you
have to cut the tran-
sition from square
to round carefully.
The gouge should
be up on edge as
you start the cut at
the line.
Photo C: Touching a pencil point lightly in each of
the notches on the turning pattern leaves an easily
visible mark on the round leg blank. These marks will
guide your cuts.
Photo D: Hold the calipers with one hand and the parting
tool with the other hand. The calipers will drop over the
sized notch when you turn to the correct diameter.
46 S HAKER- S TYLE B ED
Photo E: After
roughing out the
shape of this part
of the leg with a
gouge, finish up
the cut with a skew
chisel.
tenon shoulders. Check that the tenons
are not too long for their mortises. They
should be about 1D 32 in. short. Otherwise
when you glue up, the joint may not come
fully together.
Making the Side
Rails and Slats
1. Mill up the 3-in.-wide rails, getting a flat
and smooth surface on both edges because
you ll have glue joints on both.
2. Crosscut to 771D 2 in. long, which leaves
1 in. of extra length.
3. Smooth the top edge of the rail with a
handplane now so you won t have to do this
with the blocks attached. You can do this later
with a scraper and sandpaper, if you prefer (or
if you forget, as I did).
Adding ogee blocks
to the side rails
1. Rip the four ogee blocks to width, 5 in. for
Photo F: Sand the transition from square to round using a sanding
the headboard blocks and 3 in. for the foot-
dowel so you don t blur the edges sanding by hand.
board blocks. Find boards that match well in
color and grain so the joint between the
blocks and the rail isn t obvious. Also make
sure the end grain of the block matches that
of the rail (see  Grain Orientation on the Side
Rails on p. 49).
S HAKER- S TYLE B ED 47
2. Joint the bottom edge of the stock straight
and smooth.
3. Cut the headboard blocks to 121D 2 in. long
and the footboard blocks to 101D 2 in. long.
This leaves 1D 2 in. extra: 1D 4 in. for waste and
1
D 4 in. for the tenon.
4. Lay out the ogee shape on each block and
bandsaw to shape. Smooth the rough edges
with spokeshaves, scrapers, and sandpaper.
5. Line up the blocks with the ends of the
rails and glue them in place using cauls made
from the cutoffs (see photo I on p. 50).
6. Cut the rail ends square and to their fin-
ished length of 761D 2 in. after the glue dries.
Cutting the stub tenons
The side rails use a short tenon instead of two
Photo G: Burnish the leg with a handful of clean shavings after all the
dowels to align and reinforce the rail-to-leg
sanding is done.
joint against twist and shear forces.
Photo H: Trimming
the cheeks of the
tenons to fit the
mortises is easy with
a shoulder plane.
Note that you cut
across the grain.
48 S HAKER- S TYLE B ED
1. Rout the stub tenon shoulder. Either use 4. Drill the holes on the top face of the cleat
Tip: To pare the
the jig shown in  A Tenoning Jig on p. 24, for the dowel pins that hold the slats in place.
very top edge of the
or just rout rabbets on both sides of each end These are 5D 16-in. holes, 3D 4 in. deep. Locate
tenon shoulder
with the base of the router running on the the holes 5D 8 in. from the inside edge of the
flush, tap down
face of the rail. cleat, spaced every 5 in. starting 21D 2 in. from
with a 3D 4-in. chisel,
2. Cut away some of the tenon to create the each end.
flat side against the
top shoulder. Don t do this on the bottom 5. Squirt a little glue into each hole, then
shoulder. The
because the added cleat will create the shoul- pound in a 5D 16-in. by 11D 2-in. dowel.
der on that side. Chisel the remainder flush 6. Scribe a line with a marking gauge 1D 16 in. shoulders of the
with the shoulder surface. from the outside edge of the cleat. This is the
tenon will keep the
reference line along which you glue the rail.
chisel aligned.
Drilling for the bed bolts
7. Spread a light film of glue on the bottom of
and making recesses
the side rail, keeping glue away from the out-
for the nuts side edge to minimize the squeeze-out.
1. Locate the bed bolt holes 21D 2 in. up from 8. Place the rail on the cleat along the scribed
the bottom of the rail (not including the line and flush with the ends of the cleat.
cleat). This puts the nut in the full length por- Clamp in place.
tion of the rail and not in the ogee blocks.
2. Drill in from the end of the rail for the bolt
holes with a 3D 8-in. drill bit using a doweling
jig for accuracy.
3. If you need to extend the hole deeper than
GRAIN ORIENTATION ON THE SIDE RAILS
the jig will allow, drill the rest by hand it
will follow the existing hole well. Ideally, the grain on the different parts of the side rail should
4. Rout or drill and chisel a recess for the nut, run in the same basic direction.
as described in  A Template for Routing Nut
Boards with mixed grain
Recesses on p. 32. The only difference is the
location for the recess. The flat side of the
recess should be 31D 4 in. from the shoulder of
the rail and centered on the bolt hole.
Making and adding the
cleats to the rails
The cleats that support the slats on this bed
are screwed to the bottoms of the rails instead
of to the sides. Try to use boards that match
the color and grain of the rails.
Boards with grain running in same direction
1. Cut cleats exactly to the length of the side
rails between the tenons.
2. Plane or sand the outside edge of the cleats
smooth.
3. Drill a series of pilot holes for # 6 by
15D 8-in. screws to attach the cleat to the side
rail. Drill from the bottom, 5D 8 in. from the
outside edge of the cleat and every 4 in. If you
start 11D 2 in. from each end, you should wind 1
D 16 overhang
up with 19 screw holes (see  Cleat Details on
p. 51).
S HAKER- S TYLE B ED 49
Photo I: It s easy to
clamp the shaped
blocks to the side
rails if you use cauls
made from cutoffs
left over from mak-
ing the blocks
(painted darker for
better visibility).
Photo J: Both of
these wooden bolt
hole covers look
good with the bed.
Choose for yourself.
50 S HAKER- S TYLE B ED
CLEAT DETAILS
The screws holding the cleat to the bottom of the rail should be spaced 4 apart.
The dowel pins should be spaced 5 apart.
END VIEW SIDE VIEW
1
D 4
Dowel pins
1
2 D 2 5 5
Cleat
5 1
Dowel pin, D 16 x 1 D 2
1
D 16 overhang
Cleat
1
4 4
1 D 2
1
Pilot holes for
screws
5
5
D 8
D 8
5
2 D 16
9. Drive screws into the holes one at a time, about 3D 8 in. above the top of the counterbored
checking to be sure the rail and cleat stay bolt hole.
properly aligned. 3. Secure the covers with #6 by 3D 4-in. round-
head brass screws.
Making the bolt hole
Making the slats
covers
You can purchase bolt hole covers for this All that remains is making the bed slats and
bed, or you can make your own out of wood. finishing the bed.
The wood ones are simple to make and are
more traditional. You can either make 13D 16-in. 1. Make the 3D 4-in.-thick, 4-in.-wide bed slats
by 111D 16-in. rectangles of 1D 4-in.-thick stock, or out of maple. To get the exact length, you
cut out ovals (see photo J). should assemble the bed first and measure the
distance inside the rails.
1. To make either square or round bolt hole 2. Notch the ends on the bandsaw with a
covers, cut them to size, sand the edges router or upright on the table saw, as
smooth, then chamfer the outside face with a described in  A Jig for Notching Bed Slats on
plane or sandpaper. p. 34. Drop each slat into place over the
2. Drill 9D 64-in.-diameter holes in the tops dowel pins, then lift the mattress into place.
and 1D 16-in. or 5D 64-in. pilot holes in the legs,
S HAKER- S TYLE B ED 51


Wyszukiwarka