{added CRCOffC to rapid up and repeats, same as all other Fadal posts, 9/26/88 WFG}
{Changed max rpm from 10000 to 15000 JR 6/5/89}
{1/26/90, Updated: Fadal M003.58, to .69 format, JR}
{2/90/90, Updated: Fadal M003.69, to .70 format, JR}
{3/23/90, 15000 max RPM, JR}
{4/6/90
Added '01' literal for looping once on CallLab line at ZonlyRepAutoCycle & ZonlyRep subs.
DWB}
{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{8/10/90, Updated: Fadal M003.71 to .74 format, JR}
{8/10/90
Copied & modified: Fadal M003.74
For: Admiral
Add CRCOffsetC & ResetCRCNum.
Change to First Tool Not In Spindle.
OpToolID & ToolChng on same line.
WFO's output for MultipleParts & NewWFO only.
Added 'Z0H0' for offset cancel (full up) with CoolOff on same line.
Remove StrtPos from drill cycle line.
CoolOn on same line as OfstOn.
Combine M codes on 1 line.
Jim Radcliffe}
{4/03/91
Modified: Fadal (AEM) M332.74
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}
{7/2/92
Copied & modified from Fadal (AEM) M332.79
New designation Fadal Format 1 (AC) M509.81.2
For Amcraft
Add WFO to move to StrtPos.
Add StrtPos to WFO's at multi parts.
Change 'Z0H0' to 'G0G49Z0' for offset cancel and remove CoolOff except at end.
Add 'X0Y10.E0' to bring table to operator for loading. Works with VMC 4020 only. Y value would differ
for other models. Not ideal way to handle but consistent with customers current method.
Add 'M0' before 'M2' at end of program so that table stops at modified E0 position.
Add StrtPos to drill cycle line.
Move Rapid StrtPos lines ahead of IF Multiparts? lines.
KC}
{8/19/92
Added "SetProgNum" to reset subroutine numbers to one "1" regardless of program number
KC}
{4/6/93
Added G8 at each tool. Remove BYE from program end.
KC}
{09/07/93
Removed 'DrillCP' and 'RapidC ZCP3C' from the 'IF Drilling?' commands
KC}
{09/10/93
Changed CRC to XY plane. [ckCRC].
KC}
{09/13/93
Initial rapid goes to first Autocycle posistion instead of part origin.
Changed #6 format to add trailing 0's.
KC}
{4/15/94
Uncheck 'Allow R-Format Arcs' boolean. (Caused mixed output in programs input in metric).
KC}
{3/11/95
Copied from Fadal Format 1 (AC) M509.81.2
New designation Fadal 2 [E-SR-4A] M---.--.-
(E = fixture offsets, SR = sub routines and 4A = Fadal Flat Cam 4 Axis).
Changed to Fadal Format 2 but uses sub routines not sub programs. (L loops not M98P--).
Uses E not G54/G59.
Otherwise reverts to the standard Fanuc format.
CoolOn command M8 replaces M7
Added special aproach moves and Fadal Flat Cam forth axis commands.
[Note that geometry must be mirrored in the Y axis, and about Y0, to counter the direction
of the Fadal rotary table. If this is done, the mirror commands that Fadal suggest be added
to the NC text file are no longer required].
Removed X and Y from Canned cycles.
Changed tap cycle to Fanuc style.
KC}
{3/26/95
Modified OpenMP to handle multiple parts correctly with special Fadal Flat Cam commands.
KC}
{2/11/97
Initial: Fadal 2 [E-SR-4A] M762.85
Created: Fadal 2 [E-SR-4A-NT] MY24.85 (NT = no tool change).
Version: Virtual .025. ComPost2 68K 1.0b11
Control: CNC88
Machine: Fadal
Customer: Roberts Irrigation Products, Inc.
Comments: Remove toolchange commands (T1M6), add program stop (M0).
Add literal 'EDIT' after Q converter. (G17 Q EDIT).
No * or ( before EDIT will cause the machine to alarm deliberately).
Customer request.
KC}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '#####^##0;.'
#5 = '####.####;0.'
#6 = '########;0'
#7 = '00'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(Dwell#,4)
FORMAT(ToolDiameter#,5) {.72}
FORMAT(Program#,6) {.72}
FORMAT(Operation#,6) {.72}
FORMAT(Tool#,6) {.72}
FORMAT(NewWFO#,6) {.72}
FORMAT(Parts#,6) {.72}
FORMAT(CallMasterNum#,7)
{Prog Subroutines **********************************************************}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoSubComment:
IF UseComments? AND SubComment?
SeqLab '( SUB NUMBER: ' Program# ')' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1') {restore scale for comments}
IF ToolComment?
SeqLab '( ' ToolComment$ ')' EOL
END
RestoreScale
END
RETURN
PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN
PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLab 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLab 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLab 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLab 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN
DoPostScript:
PSInit
EachPS
SeqLab PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLab EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqLab Feed ZIn FeedEnt EOL
ELSE
SeqLab RapidC ZIn EOL
END
RETURN
StartSub:
OpenSub
SeqLab SubIDF EOL
DoSubComment
RETURN
SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
SeqLab '* WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT' EOL
' ' EOL
END
END
RETURN
StdSub:
SeqLab CallLab RepCycs EOL
StartSub
RETURN
FinishSub1: {part 1}
SeqLab CRCOffC
IF NOT FeedConnect?
RapidC ZCP3C
END
EOL
RETURN
FinishSubG92: {part 2}
SeqLab Preset ShiftR EOL
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftR EOL
RETURN
OpenMP:
NewProg
IF WorkFixtureOffsets?
SeqLab CallLab OnePart EOL
Save# Num#('1') Num#('0') { Initialize Variable 1 }
NewWFO
EACHWFO
Save# Num#('1') ADD# Recall# Num#('1') Num#('1') { Increment Variable 1 by 1 }
IF NotEqual? Recall# Num#('1') Num#('1') { Test for any value other than 1 }
SeqLab 'G0A0' SetWFO EOL
SeqLab 'G17QEDIT' EOL
SeqLab AbsOrInc Rapid StrtPos EOL
SeqLab CallLab OnePart EOL
END
IncWFO
NEXTWFO
Save# Num#('1') Num#('0') { Re-Initialize Variable 1, just to be safe }
ELSE
SeqLab CallLab Parts EOL
END
StartSub
RETURN
CloseMP:
IF WorkFixtureOffsets?
SeqLab 'G90Y0' EOL
SeqLab 'G17' EOL
SeqLab EndSub EOL
CloseSub
ELSE
SeqLab Preset ShiftP EOL
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftP EOL
END
RETURN
DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLab AbsValue EOL
END
RETURN
FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
ckCRC:
IF LastFeat?
CRCOffC
ELSE
CRCOnC
END
RETURN
StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab DoAbsOrInc ckCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqLab DoAbsOrInc ckCRC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc ckCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
RETURN
ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqLab MoveSXYC EOL
SeqLab SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqLab DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF LastFeat? AND AutoCycle? {.70}
SeqLab DoAbsOrInc CRCOffC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqLab DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLab DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab FormatArc ArcFeedC EOL
DecelMove2
END
SeqLab FormatArc DecelFeed EOL
ELSE
SeqLab FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN
WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
ELSE
SeqLab 'E' NewWFO# EOL
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
SeqLab 'E' NewWFO# EOL
END
END
END
RETURN
AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLab IncValue EOL
SeqLab StrtPosC EOL
RETURN
AutoCycCutSub2: {part 2}
ToolPath
IF Repeats? AND FeedConnect? AND ZshiftOnly?
SeqLab AbsOrInc EOL {.69 removed RapidC}
ELSE
SeqLab AbsOrInc RapidC ZCP2 EOL
END
SeqLab EndSub EOL
CloseSub
SetSRSubXY {restore tool position}
SetSRSubMove
RETURN
AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after TagInc for correct sub calls}
RETURN
Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN
G92Sub:
SubWarning
StdSub
SeqLab AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN
ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
SetPass1 {for correct Z's}
EachCycle
IF FeedConnect?
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqLab Rapid ZCP2PlusInc EOL {.69 added Rapid, reads better}
{can't call for cycle = 1, .69 changed to ZCP2PlusInc}
END
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab Rapid ZInPlusInc EOL {.69 added Rapid, reads better}
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLab CallLab '01' EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub, .69}
SeqLab Rapid ZCP2 EOL {.69}
END {.69}
SeqLab EndSub EOL
CloseSub
RETURN
ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLab Connect StrtPos EOL
END
IF FeedConnect?
SeqLab FeedC ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqLab RapidC ZCP2PlusIncC EOL {can't call for cycle =1}
{.69 added Rapid, reads better}
END
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab RapidC ZInPlusInc EOL {.69 added Rapid, reads better}
END
END
SeqLab CallLab '01' EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqLab EndSub EOL
CloseSub
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
GetStartOfSameTool:
DoOpComments
DoPostScript
WFOStuff
CheckPass
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls ('50') {?}
SetMaxRPM('15000')
SetMaxFeed('500') {?}
SetFlagF('1') { Milling ZShiftOnly SepSubs }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals : put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
SeqLab 'O' Program#
IF UseComments? AND ProgramNameComment?
'(' ProgramName$ ')'
END
EOL
SetProgNum('0')
IF UseComments?
IF ProgramComment?
SeqLab '( ' ProgramComment$ ')' EOL
END
IF FormatNameComment?
SeqLab '( FORMAT- ' FormatName$ ' )' EOL
END
END
IF ToolChangeAtHome?
SetHome
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
DoOpComments
DoPostScript
SeqLab Plane CRCOff 'G80' AbsOrInc Rapid EOL
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
SeqLab 'X0Y0A0E1' EOL
SeqLab 'G17QEDIT' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLab StrtPos EOL
SeqLab OfstOn CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLab StrtPos EOL
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
ELSE
SeqLab 'G90Y0' EOL
SeqLab 'G17' EOL
END
SeqLab CoolOff EOL
SeqLab IncValue OfstOff 'M5' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF ToolChangeAtHome?
SeqLab AbsOrInc Rapid Home
END
IF LAST ProgStop?
SeqLab 'M00' EOL
ELSE
SeqLab ProgStop EOL
END
{Start new Operation}
SeqLab 'M0' EOL
DoOpComments
DoPostScript
SeqLab Plane CRCOff 'G80' AbsOrInc Rapid EOL
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
SeqLab 'X0Y0A0E1' EOL
SeqLab 'G17QEDIT' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLab StrtPos EOL
SeqLab OfstOn CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLab StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLab CoolOff EOL
SeqLab 'G91G28Z0' SpinOff
SeqLab 'M00' EOL
{Start new Operation}
GetStartOfSameTool
SeqLab 'CHECK' EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos 'E1' EOL
SeqLab OfstOn CoolOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
{Start new Operation}
GetStartOfSameTool
SeqLab 'G91G28Z0' EOL
SeqLab SpeedC EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos 'E1' EOL
SeqLab OfstOn EOL
ELSE
{Start new Operation}
GetStartOfSameTool
SeqLab PlaneC AbsOrInc Rapid StrtPos EOL
END
IF LAST CoolOff? AND NOT CoolOff?
SeqC CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqLab ZCP2C EOL
SeqLab 'G8' EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
SeqLab RapidC CRCOffC ZCP3C EOL
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLab AbsOrInc Rapid StrtPos 'E1' EOL
END
GetCycle
SeqLab
IF RigidTap?
'G84.1'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF Tap?
FadalTapF FadalTapQ
ELSE
FeedEnt
END
EOL
IF CallMasterOp?
SeqLab 'L' CallMasterNum# '01' EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLab CallLab OnePart EOL
StartSub
ToolPath
SeqLab EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqLab 'G80' EOL
SeqLab RapidC ZCP3C EOL
IF Repeats?
FinishSubG92
END
END
END
NEXTOp
{End of program ************************************************************}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
ELSE
SeqLab 'G90Y0' EOL
SeqLab 'G17' EOL
END
SeqLab CoolOff EOL
SeqLab 'G91G28Z0M5' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF FIRST ToolChangeAtHome?
SeqLab AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
SeqLab 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqLab 'G90G0X0Y0A0E48' EOL
SeqLab EOP EOL
EndSubs
Post
EOR EOL
Close
Reseq
IF UseComments?
SetScale('1') {restore scale for comments}
END
Wyszukiwarka
Podobne podstrony:
Fadal 2 [E SR 4A NST] M761 89Fadal 2 [E SR 4A] M762 89Dynapath 20M Con [NT] MZ63 85 2Fadal 2 [E SR] M667 89Fadal Form 2 [E SR PM] M955 89Fadal Format 2 (AC) B807 12NT nanotechnologia w polsce 12Fadal Format 2 [MM] MW60 89Fadal Format 2 [PEP] M116 89 1Fadal 2 LH [WSM] MX32 89m85 (12)Fanuc 10T HS [KMT] L759 85Bridgeport EZPath WF L554 85 2EGR Quick Test 4Awięcej podobnych podstron