CCNA M4 CCNA Skills Assessment Student Training Exam


CCNA: Connecting Networks
Skills Assessment  Student Training Exam
Topology
Assessment Objectives
Part 1: Initialize Devices (2 points, 5 minutes)
Part 2: Configure Device Basic Settings (18 points, 20 minutes)
Part 3: Configure PPP Connections (17 points, 20 minutes)
Part 4: Configure NAT (14 points, 15 minutes)
Part 5: Monitor the Network (16 points, 15 minutes)
Part 6: Configure Frame Relay (17 points, 20 minutes)
Part 7: Configure a GRE VPN Tunnel (16 points, 20 minutes)
Scenario
In this Skills Assessment (SA) you will create a small network. You must connect the network devices and
configure those devices to support various WAN protocols. This will require that you reload the routers before
starting your configuration of the next WAN protocol. The assessment has you save your basic device
configurations to flash prior to implementing a WAN protocol to allow you to restore these basic configurations
after each reload.
The first WAN protocol you will configure is Point-to-Point Protocol (PPP) with CHAP authentication. You will
also configure Network Address Translation (NAT), and network monitoring protocols during this phase of the
assessment. After your instructor has signed off on this phase, you will reload the routers and configure
Frame Relay. After the Frame Relay part is complete, and has been signed off by your instructor, you will
reload the routers and configure a GRE VPN tunnel. Network configurations and connectivity will be verified
throughout the assessment by using common CLI commands.
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 16
CCNA: Connecting Networks SA Exam
Required Resources
·ð 3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
·ð 3 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term.
·ð Console cable to configure the Cisco IOS devices via the console ports
·ð Ethernet and Serial cables as shown in the topology
Part 1: Initialize Devices
Total points: 2
Time: 5 minutes
Step 1: Initialize and reload routers.
Erase the startup configurations and reload the devices.
Task IOS Command Points
Erase the startup-config file on all (1 point)
routers.
Reload all routers. (1 point)
Note: Before proceeding, have your instructor verify device initializations.
Instructor Sign-off Part 1: _________________________
Points: __________ of 2
Part 2: Configure Device Basic Settings
Total points: 18
Time: 20 minutes
Step 1: Configure PCs.
Assign static IPv4 address information (IP address, subnet mask, default gateway) to the three PCs in the
topology. Refer to the Topology diagram to obtain the IP address information.
Configuration Item or Task Specification Points
Configure static IPv4 address information on PC-A. (1 point)
Configure static IPv4 address information on PC-B. (1 point)
Configure static IPv4 address information on PC-C. (1 point)
Step 2: Configure R1.
Configuration tasks for R1 include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 16
CCNA: Connecting Networks SA Exam
Configuration Item or Task Specification Points
Disable DNS lookup (1/2 point)
Router name R1 (1/2 point)
Encrypted privileged EXEC password class (1/2 point)
Console access password cisco (1/2 point)
Telnet access password cisco (1/2 point)
Encrypt the plain text passwords (1/2 point)
MOTD banner Unauthorized Access is Prohibited! (1/2 point)
Set the description.
Set the Layer 3 IPv4 address. Use the IP address (1 1/2
information listed in the Topology. point)
Configure G0/0 Activate the interface.
Step 3: Configure R2.
Configuration tasks for R2 include the following:
Configuration Item or Task Specification Points
Disable DNS lookup (1/2 point)
Router name R2 (1/2 point)
Encrypted privileged EXEC password class (1/2 point)
Console access password cisco (1/2 point)
Telnet access password cisco (1/2 point)
Encrypt the plain text passwords (1/2 point)
MOTD banner Unauthorized Access is Prohibited! (1/2 point)
Set the description.
Set the Layer 3 IPv4 address. Use the IP address (1 1/2
information listed in the Topology. point)
Configure G0/0 Activate the interface.
Step 4: Configure R3.
Configuration tasks for R3 include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 16
CCNA: Connecting Networks SA Exam
Configuration Item or Task Specification Points
Disable DNS lookup (1/2 point)
Router name R3 (1/2 point)
Encrypted privileged EXEC password class (1/2 point)
Console access password cisco (1/2 point)
Telnet access password cisco (1/2 point)
Encrypt the plain text passwords (1/2 point)
MOTD banner Unauthorized Access is Prohibited! (1/2 point)
Set the description.
Set the Layer 3 IPv4 address. Use the IP address (1 1/2
information listed in the Topology. point)
Configure G0/0 Activate the interface.
Step 5: Save device configurations to Flash.
Use the copy running-config BasicConfig command to save the running configuration to flash on each
router. You will need this configuration file later in the assessment to restore the routers back to their basic
configuration.
Configuration Item or Task Specification Points
Copy the running-config on R1 to flash. Name the
(1/2 point)
file BasicConfig.
Copy the running-config on R2 to flash. Name the
(1/2 point)
file BasicConfig.
Copy the running-config on R3 to flash. Name the
(1/2 point)
file BasicConfig.
Instructor Sign-off Part 2: ______________________
Points: _________ of 18
Part 3: Configure PPP Connections
Total points: 17
Time: 20 minutes
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 16
CCNA: Connecting Networks SA Exam
Figure 1: PPP Topology
Use Figure 1 to obtain the IP information needed for this part of the student assessment.
Step 1: Configure R1.
Configuration tasks for R1 include the following:
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 1
at the top of Part 3 for IP address information.
(2 points)
Set encapsulation to PPP.
Set the clocking rate to 128000.
Configure S0/0/0. Activate the interface.
Configure CHAP authentication on S0/0/0. (1 point)
Username: R2
Create a local database entry for CHAP
(1 point)
authentication. Password: cisco
Set a static default route out S0/0/0. (1/2 point)
Step 2: Configure R2.
Configuration tasks for R2 include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 16
CCNA: Connecting Networks SA Exam
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure
1 at the top of Part 3 for IP address
(2 point)
information.
Set the encapsulation to PPP.
Configure S0/0/0. Activate the interface.
Configure CHAP authentication on S0/0/0. (1 point)
Username: R1
Create a local database entry for CHAP
(1 point)
authentication. Password: cisco
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure
1 at the top of Part 3 for IP address
information.
(2 points)
Set the encapsulation to PPP.
Set the clocking rate to 128000.
Configure S0/0/1. Activate the interface.
Set a static default route out S0/0/1. (1/2 point)
Set a static route for R1 LAN traffic out
(1 point)
S0/0/0.
Step 3: Configure R3.
Configuration tasks for R3 include the following:
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 1 at the top of
Part 3 for IP address information.
(2 points)
Set the encapsulation to PPP.
Configure S0/0/1. Activate the interface.
Step 4: Verify network connectivity.
Verify connectivity using the ping command.
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 16
CCNA: Connecting Networks SA Exam
From Command To Expected Results Points
PC-A ping PC-B Ping should be successful. (1/2 point)
PC-C ping R3 G0/1 Ping should be successful. (1/2 point)
PC-C ping R2 S0/0/1 Ping should be successful. (1/2 point)
PC-A ping PC-C Ping should not be successful. (1/2 point)
PC-B ping PC-C Ping should not be successful. (1/2 point)
PC-C ping PC-B Ping should not be successful. (1/2 point)
Note: It may be necessary to disable the PC firewall for pings to be successful.
Instructor Sign-off Part 3: ______________________
Points: _________ of 17
Part 4: Configure NAT
Total points: 14
Time: 15 minutes
Step 1: Configure R2.
Configuration tasks for R2 include the following:
Task Specification Points
Assign a static NAT to map the inside local IP address
(1 point)
for PC-B to a Inside Global address. Inside Global: 209.165.200.226
Define an access control list to permit the R1 LAN for
(1 point)
dynamic NAT. Access List: 1
Pool: R1-LAN
(1 point)
Define the dynamic NAT pool for the R1 LAN. Inside Global: 209.165.200.227
Define the NAT from the inside source to the outside
Inside source: Access list 1
pool. Make sure to allow multiple PCs access to this (1 point)
single Inside Global address. Outside pool: R1-LAN
Define an access control list to permit the R2 LAN for
(1 point)
dynamic NAT. Access List: 2
Pool: R2-LAN
(1 point)
Define the dynamic NAT pool for the R2 LAN. Inside Global: 209.165.200.228
Define the NAT from the inside source to the outside
Inside source: Access list 2
pool. Make sure to allow multiple PCs access to this (1 point)
single Inside Global address. Outside pool: R2-LAN
Assign the outside NAT interface. (1 point)
Assign the inside NAT interface for the R1 LAN. (1 point)
Assign the inside NAT interface for the R2 LAN. (1 point)
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 7 of 16
CCNA: Connecting Networks SA Exam
Step 2: Verify network connectivity.
Verify connectivity using the ping command.
From Command To Expected Results Points
PC-A ping PC-C Ping should be successful. (1/2 point)
PC-C ping Inside Global address for Ping should be successful. (1/2 point)
PC-B (209.165.200.226).
Note: It may be necessary to disable the PC firewall for pings to be successful.
Step 3: Verify NAT Configuration on R2.
Enter the appropriate CLI command needed to display the following:
Command Description Student Input (command) Points
Display configured access lists. (1 point)
Display the current active NAT translations. (1 point)
Display detailed information about NAT including
(1 point)
interface, access list, and pool assignments.
Instructor Sign-off Part 4: ______________________
Points: _________ of 14
Part 5: Monitor the Network
Total points: 16
Time: 15 minutes
Step 1: Configure NTP.
Configuration tasks include the following:
Task Specification Points
Date: August 25, 2013
Set the clock on R2 to a date and time specified for NTP
(1 point)
testing. Time: 9 am
Configure R2 as the NTP Master. Stratum Number: 5 (1 point)
Configure R1 so that it uses R2 as its NTP Server. (1 point)
Step 2: Configure Syslog messaging.
Configuration tasks include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 8 of 16
CCNA: Connecting Networks SA Exam
Task Specification Points
Enable the timestamp service on R1 and R2 for system Include milliseconds in the
(1 points)
logging purposes. timestamp.
Enable logging of messages on R1 and R2. Syslog server: 192.168.11.3 (1 points)
Change message trapping level on R1 and R2. Level: debugging (severity 7) (1 points)
Step 3: Configure SNMP on R1.
Configuration tasks include the following:
Task Specification Points
Create a standard access list to permit the SNMP
management station (PC-A) to retrieve SNMP (1 points)
information from R1. Access List: SNMP-ACCESS
Community: SA-LAB
Enable SNMP community access to the SNMP-ACCESS
(1 points)
access list. Access level: Read-only
Host: 192.168.11.3
Version: 2c (1 points)
Set the SNMP notification host. Community: SA-LAB
Enable all SNMP traps. (1 points)
Step 4: Collect NetFlow data on R2.
Configuration tasks include the following:
Task Specification Points
Configure NetFlow data capture on both serial
(1 points)
interfaces. Capture ingress and egress data packets.
Destination: PC-B IP address
(1 points)
Configure NetFlow data export. UDP Port: 9996
Configure the NetFlow export version. Version: 9 (1 points)
Step 5: Verify monitoring configurations.
Enter the appropriate CLI command needed to display the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 9 of 16
CCNA: Connecting Networks SA Exam
Command Description Student Input (command) Points
Display the date and time. (1/2 point)
Display the contents of logging buffers. (1 point)
Display information about the SNMP communities. (1/2 point)
Display the protocol using the highest volume of traffic. (1 point)
Instructor Sign-off Part 5: ______________________
Points: _________ of 16
Part 6: Configure Frame Relay
NOTE: DO NOT PROCEED WITH THE ASSESSMENT UNTIL YOUR INSTRUCTOR HAS SIGNED OFF ON
THE PREVIOUS PARTS.
Total points: 17
Time: 20 minutes
Figure 2: Frame Relay Topology
Use Figure 2 to obtain the IP information needed for this part of the student assessment.
Step 1: Reload routers and restore the BasicConfig to memory.
a. Erase the startup configurations and reload the devices.
b. For each router, issue the copy flash:BasicConfig running-config command to reload the basic
configuration that you saved at the end of Part 2.
c. Issue the no shutdown command for the G0/0 interface on R1 and R3.
Step 2: Configure R2 as a Frame Relay Switch.
Copy and paste the following configuration lines into R2. This will configure R2 as a Frame Relay switch and
allow you to complete Part 6.
frame-relay switching
int s0/0/0
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 10 of 16
CCNA: Connecting Networks SA Exam
encapsulation frame-relay
frame-relay intf-type dce
frame-relay route 123 interface s0/0/1 321
frame-relay lmi-type ansi
no shutdown
int s0/0/1
clock rate 128000
encapsulation frame-relay ietf
frame-relay intf-type dce
frame-relay route 321 interface s0/0/0 123
no shutdown
Step 3: Configure R1.
Configure Frame Relay on S0/0/0 on R1. Configuration tasks for R1 include the following:
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 2
at the top of Part 6 for IP address information.
(2 points)
Set encapsulation to frame-relay
Configure S0/0/0. Set the clocking rate to 128000
Disable Inverse ARP on S0/0/0. (1/2 point)
Map the IP local address to the DLCI. Refer to Figure 2 for DLCI information. (1 point)
Map the remote IP address to the DLCI. Refer to Figure 2 for IP address and DLCI
(1 point)
Allow for multicast or broadcast traffic. information.
Change the LMI type to the ANSI standard. (1 point)
Activate the interface. (1/2 point)
Create a default route to the IP address on
(1/2 point)
the other side of the Frame Relay link. Refer to Figure 2 for the IP address.
Step 4: Configure R3.
Configure Frame Relay on a subinterface of S0/0/1 on R3. Configuration tasks for R3 include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 11 of 16
CCNA: Connecting Networks SA Exam
Task Specification Points
Configure Frame Relay Encapsulation. Set
encapsulation to frame-relay (use the IETF
(1 point)
standard).
Configure S0/0/1. Activate the interface.
Subinterface #: 321
Create a point-to-point subinterface on
(1 point)
S0/0/1. Set the description.
Set the Layer 3 IPv4 address on the Refer to Figure 2 at the top of Part 6 for IP
(1 point)
subinterface. address information.
Disable Inverse ARP on the subinterface. (1/2 point)
Map the subinterface to the DLCI. Refer to Figure 2 for DLCI information. (1 point)
Create a default route to the IP address on
(1/2 point)
the other side of the Frame Relay link. Refer to Figure 2 for IP address.
Step 5: Verify network connectivity.
Verify connectivity using the ping command.
From Command To Expected Results Points
PC-A ping Default gateway Ping should be successful. (1/2 point)
PC-C ping Default gateway Ping should be successful. (1/2 point)
PC-A ping 172.27.13.2 Ping should be successful. (1/2 point)
PC-C ping 172.27.13.1 Ping should be successful. (1/2 point)
PC-A ping PC-C Ping should be successful. (1/2 point)
Note: It may be necessary to disable the PC firewall for pings to be successful.
Step 6: Verify Frame Relay configuration.
Enter the appropriate CLI command needed to display the following:
Command Description Student Input (command) Points
Display Frame Relay LMI statistics. (1 point)
Display the input and output packet count totals on a
(1 point)
Frame Relay permanent virtual circuit (PVC).
Display the Frame Relay maps between DLCIs and IP
(1 point)
addresses.
Instructor Sign-off Part 6: ______________________
Points: _________ of 17
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 12 of 16
CCNA: Connecting Networks SA Exam
Part 7: Configure a GRE VPN Tunnel
NOTE: DO NOT PROCEED WITH THE ASSESSMENT UNTIL YOUR INSTRUCTOR HAS SIGNED OFF ON
THE PREVIOUS PART.
Total points: 16
Time: 20 minutes
Figure 3: GRE VPN Topology
Use Figure 3 to obtain the IP information needed for this part of the student assessment.
Step 1: Reload routers and restore the BasicConfig to memory.
a. Erase the startup configurations and reload the devices.
b. For each router, issue the copy flash:BasicConfig running-config command to reload the basic
configuration that you saved at the end of Part 2.
c. Issue the no shutdown command for the G0/0 interface on R1 and R3.
Step 2: Configure Serial Interfaces.
a. Configuration tasks for R1 include the following:
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 3 at the top of Part 7 for IP
address information.
(1 point)
Set the encapsulation to HDLC.
Set the clocking rate to 128000.
Configure S0/0/0. Activate the interface.
b. Configuration tasks for R2 include the following:
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 13 of 16
CCNA: Connecting Networks SA Exam
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 3 at the top of Part 7 for IP
address information.
(1 point)
Set the encapsulation to HDLC.
Configure S0/0/0. Activate the interface.
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 3 at the top of Part 7 for IP
address information.
(1 point)
Set the encapsulation to HDLC.
Set the clocking rate to 128000.
Configure S0/0/1. Activate the interface.
c. Configuration tasks for R3 include the following:
Task Specification Points
Set the description.
Set the Layer 3 IPv4 address. Refer to Figure 3 at the top of Part 7 for IP
address information.
(1 point)
Set the encapsulation to HDLC.
Configure S0/0/1. Activate the interface.
Step 3: Configure the GRE VPN tunnel and EIGRP on R1.
Configuration tasks for R1 include the following:
Task Specification Points
Interface: tunnel 0
Set the description.
(2 points)
Set the Layer 3 IPv4 address. Refer to Figure 3
Create a GRE tunnel interface. at the top of Part 7 for IP address information.
Use S0/0/0 as the tunnel source. (1/2 point)
Set the tunnel destination with the IP
(1/2 point)
address of the R3 S0/0/1 interface. Refer to Figure 3 for IP address information.
Create a default route out S0/0/0. (1/2 point)
Configure EIGRP on R1 Autonomous System (AS) number: 1 (1/2 point)
Advertise the LAN and Tunnel subnets in
(1/2 point)
EIGRP. Set the LAN interface to passive. Refer to the GRE VPN topology.
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 14 of 16
CCNA: Connecting Networks SA Exam
Step 4: Configure the GRE VPN tunnel and EIGRP on R3.
Configuration tasks for R3 include the following:
Task Specification Points
Interface: tunnel 0
Set the description.
(2 points)
Set the Layer 3 IPv4 address. Use the IP
address information listed in Figure 3 at the top
Create a GRE tunnel interface. of Part 7.
Use S0/0/1 as the tunnel source. (1/2 point)
Set the tunnel destination with the IP Refer to Figure 3 at the top of Part 7 for IP
(1/2 point)
address of the R1 S0/0/0 interface. address information.
Create a default route out S0/0/1. (1/2 point)
Configure EIGRP on R3 Autonomous System (AS) number: 1 (1/2 point)
Advertise the LAN and Tunnel subnets in
(1/2 point)
EIGRP. Set the LAN interface to passive. Refer to the GRE VPN topology.
Step 5: Verify network connectivity.
Verify connectivity using the following commands.
From Command To Expected Results Points
PC-A ping Default gateway Ping should be successful. (1/2 point)
PC-C ping Default gateway Ping should be successful. (1/2 point)
PC-A ping PC-C Ping should be successful. (1/2 point)
R1 traceroute 172.27.23.1 R2 should show up in the traceroute. (1/2 point)
R1 traceroute 172.27.13.2 R2 should be absent from traceroute. (1/2 point)
Note: It may be necessary to disable the PC firewall for pings to be successful.
Step 6: Verify GRE VPN configuration.
Enter the appropriate CLI command needed to display the following:
Command Description Student Input (command) Points
Display detail information about the GRE tunnel
(1/2 point)
interface.
Instructor Sign-off Part 7: ______________________
Points: _________ of 16
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 15 of 16
CCNA: Connecting Networks SA Exam
Part 8: Cleanup
NOTE: DO NOT PROCEED WITH CLEANUP UNTIL YOUR INSTRUCTOR HAS GRADED YOUR SKILLS
EXAM AND HAS INFORMED YOU THAT YOU MAY BEGIN CLEANUP.
Before turning off power to the routers:
·ð Remove the NVRAM configuration files (if saved) from all devices.
·ð Remove the BasicConfig file from flash using the delete flash:BasicConfig command.
Router Interface Summary Table
Router Interface Summary
Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
2801 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
(F0/0) (F0/1)
2811 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 16 of 16


Wyszukiwarka

Podobne podstrony:
CCNA M4?NA Skills Assessment Student Training Exam
CCNA M3 ScaN Skills Assess OSPF Student Trng Exam
CCNA M3 ScaN Skills Assess
Cisco CCNA Certification knowledge to pass the exam
red hat skills assessment rhel6
CCNA M2 en RSE SkillsAssessment Student Exam
59487272 Accessing the WAN Student Skills Based Assessment Lab Answer Key
3? EXAM LANGUAGE ELEMENTSfor students
april 09 lowersecondary exam students
Cisco Exploration CCNA 4 0 CCNA 1 Final Exam 2011 latest (hot hot hot)
CCNA Practice Certification Exam # 2
CCNA Practice Certification Exam
CCNA 1 Final Exam
13058128 ccna practice certification exam 2
CCNA 1 Final Exam V4 0 Answers CCNA Answers CCNA Exam CCNA Exams
CCNA 2 Final Exam v

więcej podobnych podstron