Glow Worm installation and service manual Hideaway 120BF UIS


221765B.11.00
Instructions for Use
Installation and Servicing
To be l ef t wi t h t he user
Hideaway
120B
G.C. No. 41 313 28
Balanced Flue Boiler
BS 6332
BS 5258
This is a Cat I2H Appliance
Reference in these instructions to British Standards and Statutory
Regulations/Requirements apply only to the United Kingdom.
For Ireland the rules in force must be used.
The instructions consist of three parts, User, Installation and Servicing Instructions, which includes the Guarantee Registration
Card. The instructions are an integral part of the appliance and must, to comply with the current issue of the Gas Safety
(Installation and Use) Regulations, be handed to the user on completion of the installation.
Guarantee Registration
Thank you for installing a new Glow-worm appliance in your home.
Glow-worm appliances' are manufactured to the very highest standard so we are pleased
to offer our customers' a Comprehensive First Year Guarantee.
In the centre pages are to be found your Guarantee Registration Card, which we recommend you complete and
return as soon as possible.
If this card is missing you can obtain a copy or record your registration by telephoning the Heatcall Customer
Service number 01773 828100.
Our Guarantee gives you peace of mind plus valuable protection against breakdown by covering the cost of:
'
O'All replacement parts REGISTER YOUR GLOW-WORM APPLIANCE
FOR 1ST YEAR GUARANTEE PROTECTION
'
O'All labour charges
'
O'All call-out charges
CALL 0208 247 9857
Hepworth Heating Ltd.,
Customer Services:
Nottingham Road, Belper, Derbyshire. DE56 1JT
Tel: (01773) 828100
General/Sales enquiries:
Tel: (01773) 824141 Fax: (01773) 820569
One Contact Local Service Fax: (01773) 828070
1388
Important Information
Testing and Certification
This boiler is tested and certificated for safety and performance. It is therefore important that no alteration is made to the boiler, without
permission, in writing, from Hepworth Heating Ltd.
Any alteration not approved by Hepworth Heating Ltd., could invalidate the certification, boiler warranty and may also infringe the
current issue of the Statutory Requirements, see Section 1.4.
CE Mark
This boiler meets the requirements of Statutory Instrument No. 3083 The boiler (Efficiency) Regulations, and therefore is deemed
to meet the requirements of Directive 92/42/EEC on the efficiency requirements for new hot water boilers fired with liquid or gaseous
fuels.
Type test for purposes of Regulation 5 certified by: Notified body 0086.
Product/productioncertifiedby: Notified body 0086.
The CE mark on this appliance shows compliance with:
1. Directive 90/396/EEC on the approximation of the laws of the Member States relating to appliances burning gaseous fuels.
2. Directive 73/23/EEC on the harmonization of the Laws of the Member States relating to the electrical equipment designed
for use within certain voltage limits.
3. Directive 89/336/EEC on the approximation of the Laws of the Member States relating to electromagnetic compatibility.
INFORMATION FOR THE INSTALLER AND SERVICE ENGINEER.
Under Section 6 of The Health and Safety at Work Act 1974, we are required to provide information on substances hazardous to
health.
CERAMIC FIBRE/INSULATION PADS, GLASSYARN.
These can cause irritation to skin, eyes and the respiratory tract. If you have a history of skin complaint you may be susceptible to
irritation. High dust levels are usual only if the material is broken. Normal handling should not cause discomfort, but follow normal
good hygiene and wash your hands before eating, drinking or going to the lavatory. If you do suffer irritation of the eyes or severe
irritation to the skin seek medical attention.
THERMOSTATS
These contain very small amounts of xylene in the sealed phial and capillary. If broken, under normal circumstances the fluid does
not cause a problem, but in case of skin contact, wash with cold water. If swallowed drink plenty of water and seek medical attention.
CONTENTS DESCRIPTION SECTION PAGE No.
Introduction 3
INSTRUCTIONS
Lighting the Boiler 4
FOR USE
General Data 1 5
INSTALLATION
Water Systems 2 7
INSTRUCTIONS Flue and Ventilation 3 8
Installation 4 9
Casing Location / Fitting 5 12
Electrical Wiring 6 14
Commissioning 7 15
Servicing 8 17
SERVICING
Replacement Parts 9 18
INSTRUCTIONS
Fault Finding 10 21
Spare Parts 11 24
221765B 2
Instructions for Use
General Information To Connect an Electrical Plug
Please read these instructions and follow them carefully for the The standard colours of three core flexible cable are,
safe and economical use of your boiler.
Brown - live, Blue - neutral, Green and Yellow - earth.
The boiler is automatic in operation, once the pilot has been lit
As the markings on your plug may not correspond with these
and the controls set.
colours, continue as follows:
Glow-worm Hideaways are central heating boilers, to provide
The Blue cable must be connected to the terminal marked  N
heating and if required, an indirect domestic hot water supply.
or  Black .
The Brown cable must be connected to the terminal marked  L
Important Notice
or  Red .
This boiler is for use only on G20 gas.
The Green and yellow cable must be connected to the terminal
Gas Safety (Installation and Use) Regulations
marked  E or  Green or the earth symbol .
In your own interests and that of safety, is the law that ALL gas
To Light the Boiler
appliances are installed by a competent person in accordance
with the current issue of the above regulations.
WARNING. If the pilot light goes out for any reason, do not
attempt to relight until 3 minutes have elapsed.
Warning
Remove the door by pulling forwards with the fascia at the top.
Make sure that nothing obstructs the rear side grille or clearances.
Lift up to disengage from the bottom side lugs.
See page 4 for minimum clearances.
Refer to diagram 1 to identify controls.
Boilers Installed in a Compartment
Check that the mains electrical supply to the boiler is switched
OFF.
If the boiler is fitted in a compartment, cupboard etc., do not
obstruct the purpose built compartment vents or the grille on the
boiler.
Do not use the compartment for storage purposes.
THERMOSTAT
Maintenance
CONTROL
To ensure the continued efficient and safe operation of the boiler
KNOB 'B'
it is recommended that it is checked and serviced as necessary
at regular intervals. The frequency of servicing will depend upon
the particular installation conditions and usage, but in general
PIEZO IGNITION
once a year should be enough.
BUTTON 'C'
It is the law that servicing must be carried out by a competent
person.
GAS
If this appliance is installed in a rented property there is a duty
CONTROL
of care imposed on the owner of the property by the current
KNOB 'A'
issue of the Gas Safety (Installation and Use) Regulations,
Section 35.
SETTING
To obtain service please call your installer or Heatcall (Glow-
POINT
worm s own service organisation) using the telephone number
given on the front panel.
Please be advised that the  Benchmark logbook should be
completed by the installation engineer on completion of
commissioning and servicing.
All CORGI Registered Installers carry a CORGI ID card, and
have a registration number. Both should be recorded in your
E
boiler Logbook. You can check your installer is CORGI registered
SETTING
by calling CORGI direct on :- 01256 372300.
POINTS
Boiler Electrical Supply
WARNING. This boiler must be earthed.
The boiler must only be connected to a 230V~50Hz supply
protected by a 3A fuse, maximum.
All wiring must be in accordance with the current issue of
GAS CONTROL KNOB
BS7671.
= OFF
Heat resistant flexible cable having a conductor size of 0.75mm2,
= PILOT/IGNITION
to the current issue of BS6500 Table 16 must be used.
= MAIN BURNER
Diagram 1
3 221765B
9009
Instructions for Use
Push in slightly and turn gas control knob  A clockwise until
Sheet Metal Parts
is against its setting point.
WARNING. This boiler contains metal parts (components) and
Turn thermostat control knob  B anticlockwise until  O is
care should be taken when handling and cleaning, with particular
against its setting point.
regard to edges.
Push in slightly and turn gas control knob  A anticlockwise until
Cleaning
is against its setting point, then depress fully and hold in.
Push in and release piezo ignition button  C until the pilot Keep the casing clean by wiping it occasionally with a damp
burner lights. soapy cloth and dry with a polishing cloth.
Air may be present in the supply pipe so the lighting of the pilot Do not use abrasive cleaners.
may need to be repeated until all the air has been expelled.
Replacement Parts/Boiler Identification
When the pilot is alight, view through window  E , keep gas
control knob  A fully pushed in for about 15 seconds, then If replacement parts are required apply to your local supplier.
release. Please quote the name of the boiler and its serial number which
can be found on the data label, positioned on the boiler top, to
If the burner fails to stay alight, wait 3 minutes, then repeat the
the rear of the inclined flueway cleaning door.
lighting procedure only now keep control knob  A pushed in for
a little longer before releasing.
Clearances
Press in and turn gas control knob  A anticlockwise until is
Minimum clearances must be left around the boiler as shown in
against its setting point.
diagrams 1.3, 1.4 and 1.5.
If the gas control knob  A is turned to , a safety lock prevents
it being turned on again for a short period. No attempt should
be made to relight the pilot until 3 minutes have elapsed.
Make sure that the pilot is alight and stable then switch on the
electrical supply.
Set any system controls to  ON or  HIGH .
Turn the boiler thermostat knob  B clockwise until  MAX is
against its setting point and the main burner will light. Adjust
thermostat to required setting between  MIN and  MAX .
 MAX is about 82oC (180oF).
Refit the door by locating the hooked runner at the bottom into
the slot in the side panels and pushing onto the studs.
To Turn the Boiler Off
For short periods, turn the boiler thermostat control knob  B
anticlockwise to  O . The pilot will stay alight. To relight the
main burner turn thermostat control knob  B clockwise to the
desired setting between  MIN and  MAX .
For longer periods, depress slightly and turn gas control knob
 A fully clockwise until is against its setting point. Turn
thermostat control knob  B anticlockwise to  O . Isolate the
boiler from the electrical supply. Follow full lighting procedure
to relight. Refer also to  Protection Against Freezing .
Gas Leak or Fault
If a gas leak fault exists or is suspected the boiler must be turned
off, including the electrical supply and must not be used until the
fault has been put right. Advice/help should be obtained from
the local gas undertaking or your installation/servicing company.
Protection Against Freezing
If the boiler is to be out of use for any period of time during severe
weather conditions we recommend the whole system including
the boiler, be drained off to avoid the risk of freezing up. If an
immersion heater is fitted to the hot water cylinder make sure it
is switched off.
221765B 4
General Data
=' Refer to BOILER CASING GAS CONNECTION
WATER CONNECTIONS Rc1 reduced
Rc 1/2 (1/2 in. B.S.P.T.)
HEIGHT diagram
with DISTRIBUTOR TUBE to
Rc 3/4 (3/4 in. B.S.P.T.) (pumped return)
' A SPECIAL TOP CASING
WATER CONNECTIONS
TO SUIT 600mm (235/8 in.)
Rc1 (1in. B.S.P.T.)
WORKTOPS IS AVAILABLE
' F(MIN.)
N
A
L
G(MIN.)
C P
L
H
C
L
B
J
='
C D
C
L
K M
E
G(MIN.)
GENERAL DIMENSIONS - given in millimetres (Approx. inches) Diagram 1.1
A B C D E 'F G H J K L M N P
mm 474 214 558 294 359 533 3 300 445 121 156 664 398 398
1
in. 1811/16 81/2 22 111/2 141/8 21 /8 113/4 171/2 43/4 61/8 261/8 155/8 155/8
Important Notice
1.4 Statutory Requirements
This boiler is for use only on G20 gas.
The installation of this boiler must be carried out by a competent
person in accordance with the relevant requirements of the
Wherever possible, all materials, appliances and components
current issue of:
used shall comply with the requirements of applicable British
Standards.
Manufacturer s instructions, supplied.
Where no British Standard exists, materials and equipment
The Gas Safety (Installation and Use) Regulations, The Building
should be fit for their purpose and of suitable quality and
Regulations, The Bye-laws of the Local Water Company, The
workmanship.
Building Standards (Scotland) Regulations, (applicable in
Scotland), The Health and Safety at Work Act, Control of
1.1 Data
Substances Hazardous to Health, Electricity at Work Regulations
and any applicable local regulations.
Weight of boiler 147.0kg (324lb)
Detailed recommendations are contained in the current issue of
Water content 11.7litre (2.57gall)
the following British Standards and Codes of Practice:
Gas connection Rc1/2 1/2inBSP
BS6798, BS5440 Part 1 and 2, BS5546, BS5449 Part 1,
Water connection Rc1 1 in BSP
BS6700, BS6891, BS7478, BS7593, BS7671.
Electrical supply 230V ~ 50Hz fused 3A
Manufacturers instructions must in not be taken as overriding
Burner Aeromatic (2 off)
statutory requirements.
All dimensions are given in millimetres, except as noted.
The Seasonal Efficiency Domestic Boilers UK (SEDBUK)
is 72.0%.
min medium max
RANGE RATING
The value is used in the UK Government s Standard Assessment
Procedure (SAP) for energy rating of dwellings. The test data
NOMINAL kW 37.0 40.55 44.13
from which it has been calculated have been certified by B.S.I.
HEAT INPUT
126,250 138,370 150,560
(GROSS) Btu/h
1.2 Range Rating
This boiler is range rated and may be adjusted to suit individual
NOMINAL kW
29.31 32.24 35.17
system requirements.
HEAT
The Tables give the appropriate settings and ratings.
OUTPUT Btu/h 100,000 110,000 120,000
The boiler heat input is factory preset to its maximum rating.
This should be adjusted to suit individual system requirements.
BURNER mbar
9.8 11.7 13.8
SETTING
The arrow indicator, from the loose items pack, should be stuck
PRESSURE in.w.g 3.9 4.7 5.5
on the data label to indicate the setting.
(HOT)
1.3 Sheet Metal Parts
205746
INJECTOR
WARNING. When installing or servicing this boiler, care should
be taken to avoid any possibility of personal injury when
handling sheet metal parts.
5 221765B
1071
General Data
1.5 B.S.I. Certification To facilitate minimum clearances it may be necessary to modify
the kitchen units or fixtures, depending upon which type of
This boiler is certificated by B.S.I. for safety and performance.
connections are used.
It is, therefore, important that no alteration is made to the boiler,
without permission, in writing, from Hepworth Heating Ltd. A front access clearance should be provided as shown in
diagram 1.5.
Any alteration not approved by Hepworth Heating Ltd., could
invalidate the B.S.I. certification, boiler warranty and could also The minimum gap behind the top casing is as shown in diagram
infringe the Statutory Requirements. 1.1. The boiler can be sited further away from the wall if required
to align with kitchen units etc. Refer to Section 3.5.
1.6 Gas Supply
Combustible wall material must be 25mm (1in) away from flue
The gas installation shall be in accordance with the current
components. Refer to Section 3.5.
issue of BS6891.
The supply from the governed meter must be of adequate size
to provide a steady inlet working pressure of 20mbar (8in wg) at
BOILER
BOILER
To
the boiler.
WITHOUT
WITH TOP
floor
On completion test the gas installation using the pressure drop
TOP CASING
CASING
level
method and suitable leak detection fluid, purge in accordance
with the current issue of BS6891.
MAX.900 (351/2 in.) MAX.867 (341/8 in.)
MID. 890 (35in.) MID. 857 (333/4 in.)
1.7 Electrical
MIN. 860 (34in.) MIN. 827 (321/2 in.)
WARNING. This boiler must be earthed.
The electrical installation must be carried out by a competent
person.
MAX.
MAX.
All external components shall be of the approved type and shall
be connected in accordance with the current issue of BS7671
MID.
MID.
and any local regulations which apply.
MIN.
MIN.
Connection of the boiler and any system controls to the mains
supply should be through an unswitched shuttered socket outlet
BOILER CASING ALTERNATIVE
and 3A fused 3 pin plug both to the current issue of BS1363.
FLOOR
Alternatively, a 3A fused double pole isolating switch may be
HEIGHT POSITIONS
LEVEL
used, having a minimum double pole contact separation of
Diagram 1.2
BOILER CASING HEIGHT(S)
3mm, serving the boiler and system controls only.
Heat resistant flexible cable of at least 0.75mm2 (24/0.20mm)
to BS6500 Table 16, must be used for all connections within the
WORKTOP
494 MIN.
boiler casing.
(197/16 in.)
1.8 Boiler Location
This boiler is not suitable for outside installation.
BOILER BOILER
10
10
The boiler may be installed in any room, although particular
5
attention is drawn to the requirements of the current issue of
(3/8 in.)
(3/8 in.) (3/16 in.)
BS7671 with respect to the installation of the boiler in a room
494 MIN.
containing a bath or shower. Any electrical switch or boiler
control utilising mains electricity should be so situated that it
(197/16 in.)
cannot be touched by a person using the bath or shower. The
electrical provisions of the Building Standards (Scotland)
CUPBOARDS
Regulations are applicable to such installations in Scotland.
MINIMUM CLEARANCES
The boiler must stand on a level floor, conforming with the local
LEVEL WITH WORKTOP
authority requirements and building regulations. The base
Diagram 1.3
temperature is within the requirements of BS5258. The boiler
may be stood on a wooden floor but a metal base plate is
required to protect plastic tiles and similar floor coverings. WORKTOP OR FIXTURE
Suitable clearance needs to be available at the sides of the
10 (3/8 in.) 3 (1/8 in.)
boiler to facilitate direct connection of pipework and making
CUPBOARD
CUPBOARD
good around the flue assembly. The actual clearance required
will vary with site conditions.
The casing can be fitted to the boiler at various heights. The top
casing can be discarded, if preferred, when fitting the boiler
10 10
10
under a worktop or fixture. See diagram 1.2.
(3/8 in.)
(3/8 in.) (3/8 in.)
BOILER BOILER
When the boiler is to be installed level with work surfaces etc.,
minimum clearances should be provided as shown in diagram WITH WITHOUT
1.3. Work tops which overhang the cupboard sides almost in
TOP TOP
contact with the casing top, require a larger minimum air gap.
CASING CASING
Flush sided fixtures require the same overall minimum space
but can have a reduced air gap on one side.
CUPBOARD
Boilers to be installed under work tops or fixtures, with or without
MINIMUM CLEARANCES
the casing top fitted, should be positioned to provide minimum
Diagram 1.4
UNDER WORKTOP, FIXTURES
clearances as shown in diagram 1.4.
221765B 6
0982
1387
0865
1 General Data
A special top casing, part No. 424820, can be purchased to
enable the boiler casings to be arranged flush with 600mm (235/
in) deep work tops and kitchen units.
8
Where the installation of the boiler will be in an unusual location,
special procedures are necessary, the current issue of BS6798
BOILER
gives guidance on this.
700 (271/2 in.)
A compartment used to enclose the boiler must be designed
and constructed specifically for this purpose. An existing
cupboard or compartment modified for the purpose may be
used. Details of essential features of cupboard design are
given in the current issue of BS6798.
WALL OR
If the boiler is to be installed in a compartment, make sure that FIXTURE
nothing will obstruct the openings/vents in the compartment.
1.9 Heating System Controls
Diagram 1.5
FRONT CLEARANCE
The heating system should have installed: a programmer and
Note: For further information, see The Building Regulations
room thermostat controlling the boiler.
1991 - Conservation of fuel and power, 1995 edition - Appendix
Thermostatic radiator valves may be installed in addition to the
G, table 4b.
room thermostat.
2 Water Systems
2.1 Water Pressure Head
REFER TO BS 5546
This boiler shall only be connected to a cistern supply, with a
22mm VENT
minimum head of 1 metre (3ft) and a maximum of 27 metres
15mm COLD FEED
(90ft) and having an open vent in the system.
The boiler must not be connected to a sealed water system.
INDIRECT
2.2 Inhibitor CYLINDER
27metre
Attention is drawn to the current issue of BS5449 and BS7593
Max.
on the use of inhibitors in central heating systems.
If an inhibitor is to be used in the system, contact should be
28mm
made with an inhibitor manufacturer so they can recommended
PUMP
their most suitable product.
BOILER
When using in an existing system take special care to drain the
C
L
entire system, including the radiators, then thoroughly cleaning
To Heating
out before fitting the boiler, whether or not adding an inhibitor.
Circuit
DRAIN OFF
Distributor tube in
2.3 Gravity Domestic and Pumped Heating
COCK
pumped return
connection
It is recommended that a cylinder thermostat is used to prevent
Diagram 2.1
the stored water temperature becoming unnecessarily high.
The primary flow and return must be 28mm. The
22mm VENT
installation must comply with the current issue of BS5546 and
BS6700, see diagram 2.1.
15mm
COLD FEED
If the above conditions cannot be met, it is suggested that a fully
pumped system be used.
1 metre
TO INDIRECT
Fully Pumped System
MIN.
CYLINDER
27metres
Where a single pumped, flow and return is taken from the boiler,
MAX.
refer to diagram 2.2.
2.5 Circulation Pump PUMP
The pump should be set to give a temperature difference of
BOILER
11oC (20oF) across the system. At the appropriate flow rate the C
L
To Heating
resistance through the boiler can be found from the pressure
Circuit
loss graph, diagram 2.3.
DRAIN OFF
Distributor tube in
If possible use a pump with integral valves, if not fit valves as
COCK
pumped return
close as possible each side of the pump.
connection
FULLY PUMPED SYSTEM
Note: If the pump is to be fitted inside the boiler casing a heat
Diagram 2.2
shield kit is required. Kit No. 425839. (DIAGRAMMATIC)
7 221765B
0906
0869
0870
2 Water Systems
2.6 Cylinder
FLOW RATE (GALLON/MINUTE)
For all systems supplying domestic hot water the cylinder must 0 1 2 3 4 5 6 7 8 9 10
be indirect and to the appropriate British Standard.
1.2
2.7 Safety Valve
40
1.0
A safety valve need not be fitted to an open vented system.
0.8
30
2.8 Draining Tap
A drain tap must be provided at the lowest points of the system
0.6
which will allow the entire system, including the boiler and
20
domestic hot water cylinder to be drained. Drain taps shall
0.4
comply with the current issue of BS2879.
10
0.2
0 0
0 10 20 30 40 50
FLOW RATE (LITRES/MINUTE)
Diagram 2.3
PRESSURE LOSS OF BOILER
3 Flue and Ventilation
3.1 Flue
A suitable guard is available from
Detailed recommendations for flues are given in the current
Tower Flue Components Ltd.,
issue of BS5440 Part 1.
Morley Road,
The boiler must be installed so that the flue terminal is exposed
Tonbridge,
to the external air. It is important that the position allows the free
Kent.
passage of air across it at all times.
TN9 1RA
3.2 Terminal Positioning
reference type  F
The minimum acceptable spacings for the terminal to
obstructions, other terminals and ventilation openings are given
3.5 Flue Duct Length
in diagram 3.1.
The flue lengths quoted below allow the minimum rear clearance
Car port or similar extensions of a roof only, or roof and one wall,
of 3mm (1/8inch) behind the boiler, although the boiler can be
require special action with regard to openings, doors and
installed further away from the inside wall. In such cases any
windows under the roof. Care is required in protecting plastic
extra clearance behind the boiler must be added to the wall
roofs. If the car port consists of a roof and two or more walls
thickness to obtain the flue duct length.
seek advice form the local gas undertaking.
Check the wall thickness/flue duct length where the boiler is
Where the terminal is within 850mm (34in) below plastic guttering,
fitted. Flues available are:
or within 450mm (18in) of painted eaves or gutter an aluminium
Standard pack - 280 to 410mm (11 to 16inches).
shield 1.5 metres (5ft) long should be fitted to the underside and
Short pack - 150 to 280mm (6 to 11inches)
immediately beneath the guttering.
The air inlet/products outlet duct and the terminal of the boiler
The short flue pack, part No.425504 is available to order.
must not be closer than 25mm (1in) to combustible material.
Standard pack is part No.424886.
3.3 Timber Frame Buildings
3.6 Room Ventilation
If the boiler is to be installed in a timber frame building it should
The boiler is room sealed and does not require the room or
be fitted in accordance with the Institute of Gas Engineers
space containing it to have permanent air vents.
document IGE/UP/7/1998. If in doubt seek advice from the local
gas undertaking or Hepworth Heating Ltd.
3.4 Terminal Guard
A terminal guard is required if persons could come into contact
with the terminal or the terminal could be subject to damage.
If a terminal guard is required, it must be positioned to provide
a minimum of 50mm clearance from any part of the terminal and
be central over the terminal.
221765B 8
1370
WATER PRESSURE LOSS
(INCHES HEAD OF WATER)
WATER PRESSURE LOSS
(metre HEAD OF WATER)
3 Flue and Ventilation
3.7 Cupboard/Compartment Ventilation
Where the boiler is fitted in a cupboard or compartment, the high
C
and low level permanent air vents must have effective areas in
A
accordance with the Compartment Air Vent Table.
B,C
B,C
K
Both the high level and the low level air vents must communicate
L
L
with the same room, or must both be on the same wall to outside G
A K
K
air. F
F
F
A
G
E G
G
G
Under Car Port etc.
D
J
F
K
H,I
MINIMUM SITING DIMENSIONS FOR
BALANCED FLUE TERMINALS
POSITION MINIMUM
SPACING
A DIRECTLY BELOW AN OPENABLE mm
WINDOW, AIR VENT, OR ANY
OTHER VENTILATION OPENING 300
B BELOW GUTTER,DRAIN/SOIL PIPE 300
C BELOW EAVES 300
D BELOW A BALCONY OR CAR PORT 600
E FROM VERTICAL DRAIN PIPES
AND SOIL PIPES 75
F FROM INTERNAL OR EXTERNAL
COMPARTMENT AIR VENT TABLE
CORNERS 600
COMPARTMENT
G ABOVE ADJACENT GROUND OR
HIGH LEVEL LOW LEVEL
VENTILATION
BALCONY LEVEL 300
REQUIREMENTS VENT AREA VENT AREA H FROM A SURFACE FACING
THE TERMINAL 600
I FACING TERMINALS 600
VENTILATION
J FROM OPENING (DOOR/WINDOW)
406cm2 62in2 406cm2 62in2
FROM ROOM
IN CARPORT INTO DWELLING 1200
OR SPACE
K VERTICAL FROM A TERMINAL 1500
FROM
L HORIZONTALLY FROM A TERMINAL 300
203cm2 31in2 203cm2 31in2
OUTSIDE Diagram 3.1
4 Installation
Before fixing the boiler make sure that the location selected is
4.3 Planning Water Connections - Gravity
in accordance with the requirements of Section 1.8.
Domestic and Pumped Heating.
It is important that all connections are made as shown in
4.1 Unpacking
diagram 4.2.
Remove the packaging and then the boiler from its pallet by
removing the screws. Heating flow, either one of the two upper front connections may
be used.
The boiler casing panels are packed separately within the main
carton. They are designed to enable gas and water connections
Domestic gravity flow, any one of the three remaining upper
to be made before fitting the casing.
connections may be used.
The casing brackets, distributor tube and loose items, in a
Heating return, the water distributor tube MUST be fitted into
plastic bag, are packed in the corner fitment.
either one of the front lower connections on all installations, see
diagram 4.3. The distributor tube is packed in the top fitment.
4.2 Casing Brackets
Domestic gravity return, any one of the three remaining lower
Fit the two upper and two front casing brackets as shown in
connections may be used for the gravity domestic hot water
diagram 4.1 using eight of the No.8 screws.
return.
Push the captive nuts, supplied loose, on to the casing brackets
as shown in diagram 4.1.
9 221765B
1112
4 Installation
Fit plugs into all unused connections.
UPPER CASING
NOTE, if only limited clearance is available it is recommended
BRACKET
that the front tappings are used.
4.4 Planning Water Connections - Fully
Pumped Systems
It is important that all connections are made as shown in
diagram 4.4.
CAPTIVE
Flow, either one of the two upper front connections may be
No.8 SCREW (8)
NUT
used,
Return the water distributor tube MUST be fitted into the return
connection on all installations, see diagram 4.3. The distributor
tube is packed in the top fitment.
4.5 Thermostat Pocket
CAPTIVE
FRONT
Fit the thermostat phial pocket, supplied in the top fitment, into
NUT
CASING
the front tapping adjacent to the heating flow connection and
plug the other front pocket connection.
BRACKET
Carefully unwind the thermostat capillary, insert phial fully into
Diagram 4.1
CASING BRACKETS FITTING
the pocket and secure with the location washer behind the
retaining split pin, supplied in the loose items pack, see diagram
4.5.
DOMESTIC GRAVITY
ALTERNATIVE
4.6 Pump Within Boiler Casing
FLOW TO ANY OF THE
HEATING FLOW
3 REMAINING UPPER
If the pump is to be fitted inside the boiler casing, see diagram
(Thermostat
CONNECTIONS
6.2, ensure that a heat shield kit is obtained and fitted
phial and pocket
(Kit No. 425839).
must be adjacent
The kit contains a flueway cleaning door with heat shield
to heating flow
(attached).
connection)
4.7 Positioning/Connecting Boiler
If the boiler casings are to fit flush with any kitchen units, the
distance the boiler is away from the wall must be measured and
ALTERNATIVE
DOMESTIC
dimension  G increased by this amount, see diagram 1.1.
HEATING
GRAVITY
Having selected the position of the boiler, mark out and cut a
RETURN
RETURN TO
hole through the wall where the boiler is to be installed, to the
With distributor
ANY OF THE
dimensions shown in diagram 4.6, after checking that sufficient
tube (not
clearances will be left around the boiler as described in Section
3 REMAINING
shown)
1.8  Boiler Location , refer also to Section 3.5  Flue Duct
LOWER CONNECTIONS
Length .
WATER CONNECTIONS - GRAVITY
Fit the distributor tube, see diagram 4.2 or 4.4 for position, see
Diagram 4.2
DOMESTIC, PUMPED HEATING
diagram 4.3 for alignment. Fit appropriate fittings and plugs into
the boiler connections.
IMPORTANT NOTE, do not route any pipes across the front of
the boiler thermostat pocket, the controls, burner supply pipe,
combustion chamber cover or flueway cleaning door. The gas
supply pipe should be run along the left-hand side of the boiler.
UPPER MARKER must
If the flue duct length necessitates the use of the flue extension
lie between the two outer
kit, that is 410 to 610mm (16 to 24inches) this will need to be
NOTCHES
assembled before positioning the boiler. Read the separate
instructions supplied with the kit in conjunction with Section 4.8
 Balanced Flue Terminal .
When suitable installation clearances are available, position
the boiler in readiness to connect pipework.
DISTRIBUTOR
If suitable clearances are not available it will be necessary to
TUBE
preplumb the gas and water connections before positioning the
must be in pumped
boiler.
return connection
When the front tappings are used it is essential that any
pipework of fittings be assembled as shown in diagram 4.7., that
BOILER
UPPER
is, do not stick out more than shown.
MARKER
Diagram 4.3
DISTRIBUTOR TUBE
221765B 10
0888
1309
1277
4 Installation
When using a rear tapping with Rc1 (1inch BSP) fittings for
28mm o.d. pipework it is recommended that a short nipple and
a R thread (BSP) copper elbow is used. If the pipework is
required to run back to the wall make sure that it will clear the
boiler air duct and, if working to minimum clearance does not
stick out too far from the boiler, see diagram 4.8.
Make the water connections to the system pipework.
ALTERNATIVE
Make the connection to the gas supply at the union gas service
FLOW
cock. Test the complete gas installation for soundness and
purge in accordance with the current issue of BS6891. (Must be adjacent
to THERMOSTAT
When the boiler is finally positioned with the balanced flue duct
PHIAL POCKET)
sticking out into the prepared hole in the wall and pipework
connected, make good to the inside of the wall face around the
boiler flue assembly.
4.8 Balanced Flue Terminal
ALTERNATIVE
Take the balanced flue assembly from its carton and remove the
RETURN
four screws to release the outer baffle, see diagram 4.9.
With distributor
Remove the four outer wire guards then pull off the inner baffle/
tube (not shown)
flue duct assembly.
Place the air duct assembly into the prepared hole, from the
outside, engaging it over the boiler air duct. Slide it until the wall
WATER CONNECTIONS
plate contacts the outer wall surface.
Diagram 4.4
FULLY PUMPED SYSTEMS
Cut and fix four pieces of the yellow tape provided into the four
corners at the joint in the air duct, running the tape on the inside
of the duct about 25mm (1inch) along the joint from the corners.
LOCATION
THERMOSTAT
Fix four further pieces along the joints overlapping the corner
WASHER
tapes, to make a good seal. CAPILLARY
Cement around the wall plate to make good and provide a
weatherproof seal.
RETAINING
SPLIT PIN
Refit the inner baffle/flue duct assembly over the boiler flue duct
and slide in until the baffle contacts the wire guards.
Seal the flue duct joint on the inside using the semi-transparent,
heat resistant, tape provided, in a similar way to the air duct
PHIAL
sealing procedure, making sure that a good seal is made at the
POCKET
corners.
Refit the wire guards, outer baffle and secure with the screws SECURING THE
previously removed.
Diagram 4.5
THERMOSTAT PHIAL
360
(141/4 in.)
BALANCED
360
FLUE DUCT
(141/4 in.)
FROM BOILER
PREPARED
HOLE IN
485
THE WALL
3 (1/8 in.)
(19 in.)
MIN.
;;;
;;;
;;;
;;;
;;;
;
;;
PREPARED HOLE IN
THE WALL DIMENSIONS
Diagram 4.6
11 221765B
1310
1870
1384
4 Installation
'A'
'B'
VIEW ON
VIEW ON ARROW 'A'
ARROW 'B'
57 MAX.
BOILER
(2 1/4 in.)
BOILER
57 MAX.
(2 1/4 in.)
57 MAX.
(2 1/4 in.)
FOR
57 MAX.
MINIMUM
(2 1/4 in.)
CLEARANCE
REAR CONNECTION
PIPEWORK CASING
PIPEWORK (28mm)
Diagram 4.7
Diagram 4.8
CLEARANCES
BOILER
WALL
AIR DUCT
PLATE
INNER BAFFLE/
FLUE DUCT
ASSEMBLY
OUTER
BAFFLE
AIR DUCT
ASSEMBLY
WIRE GUARDS
SCREW (4)
TERMINAL AND AIR DUCT -
STANDARD OR SHORT
Diagram 4.9
5 Casing Location / Fitting
5.2 Side Casings
5.1 Side Vent Grille
Fit each side casing by locating the lugs into the appropriate
One side vent grille is supplied with the boiler and can be fitted
slots in the boiler plinth, see diagram 5.2, depending on the
at the rear of the left or right-hand side casing. The grille is fitted
required casing height, see diagram 1.2.
on the opposite side to any pipework connections.
Secure the side casings to the casing brackets at the front and
If required, fit the grille, using plastic pegs at the top and bottom,
top.
see diagram 5.1, prior to fixing the side casing. The plastic pegs
are a tight fit, so they are best pushed home with a flat faced tool.
Discard the grille if water connections are made on both sides
of the boiler or if the boiler is screened by fixtures.
221765B 12
1524
1525
1280
5 Casing Location / Fitting
5.3 Top Casing
The top casing can be fitted in four alternative positions, that is,
PLASTIC PEG (4)
TOP CASING
with either a rolled or square front edge, flush with the door or
overhanging it by 10mm (3/8inch).
Select either a rolled or square front edge and for a flush fitting
top casing, fit four plastic pegs into holes  A as shown in
diagram 5.3. For overhanging top casing, fit four plastic pegs
into holes  B . The plastic pegs are a tight fit so they are best
B
A
pushed home with a flat faced tool.
Fit the top casing by engaging the pegs in to the holes in the side
SIDE A
B
casings and then make sure that they are fully engaged by
CASING
pushing the pegs down.
(L.H.)
For boilers fitted under work tops, not using the casing top, the
strap should be fitted as diagram 5.4.
PEG POSITIONS IN TOP CASING
A = FRONT EDGE FLUSH
B = 10mm (3/8 in) FRONT OVERHANG
PLASTIC PEG
AB AB
SIDE CASING
SIDE VENT GRILLE
DOOR
BOILER SHOWN WITH
(If required, will fit to
ROLLED EDGE FLUSH
left or right side casing)
SIDE CASING
(R.H. SHOWN)
AB AB
Diagram 5.1
SIDE VENT GRILLE
UPPER
SIDE CASING
CASING
MIN. DOOR
BRACKET
BOILER SHOWN WITH
SQUARE EDGE FLUSH
MID.
TOP CASING FITTING
Diagram 5.3
MAX.
No. 8 SCREW
(4)
SIDE
LOCATING
CASING
LUG AND SLOTS
(L.H.) SIDE CASING
(R.H.)
MIN.
CAPTIVE
MID.
NUT
MAX. MAX.
MID.
No.8 SECURING
FRONT
SCREW
STRAP fitted when no
MIN.
CASING
top casing
BRACKET
BOILER PLINTH
Diagram 5.4
STRAP FITTING (No top casing)
SIDE CASINGS FITTING Diagram 5.2
13 221765B
0886
0885
0914
0909
6 Electrical Wiring
6.1 Control Box Cable Connection.
WARNING. This boiler must be earthed.
COVER
Remove the screw and cover from the mains inlet connector,
supplied loose, see diagram 6.1.
Using heat resistant flexible cable of a suitable length and rating
as stated in Section 1.7  Electrical connect the three wires to
the appropriate terminals in the connector.
L
E
Engage slots and lugs, replace cover and secure with screw. N SLOTS
Connect the mains inlet connector to the control box and use
CABLE
three of the cable clips, from the loose items pack, pushed onto
CLAMP
LUGS
the edge of the right-hand panel in position CB as shown on
diagram 6.2 to ensure the cable does not touch any hot
surfaces.
MAINS INLET
CONNECTOR
Diagram 6.1
6.2 Pump Cable Connection
Heat resistant cable as above must be used if the pump is to be
fitted inside the casing.
Support the cable in a similar manner to Control Box Connection,
only fit clips to the casing at P or AP as diagram 6.2.
P
6.3 System Controls 230
CB
(9)
P
AP
The electrical installation must be made in accordance with the
230
current issue of BS7671.
25
AP (9)
230
CB
(1)
The electrical isolator must isolate both the appliance and
(9)
system controls.
6.4 Testing
Checks to ensure electrical safety should be carried out by a
competent person.
In the event of an electrical fault after installation of the boiler,
preliminary system checks must be carried, that is, earth
continuity, polarity and resistance to earth, as described in the
CB
British Gas Multimeter Instruction Book or equal publication.
CB
Fit 2 pump cable
clips at positions P
Alternative pump
Fit 4 control
cable clips (if feed is
box feed cable
on the left hand side)
clips at positions
at positions AP
CB
CABLE CLIP POSITIONS
Diagram 6.2
221765B 14
0878
9016
7 Commissioning
Please ensure the  Benchmark logbook is completed and left control knob  A fully pushed in for about 15 seconds. If the pilot
with the user. burner fails to stay alight, repeat the lighting procedure only now
keep the control knob pushed for a little longer.
7.1 Preliminaries
If the gas control knob  A is turned to' 'a safety lock prevents
With the pump removed the whole of the system should be
it being turned on again until 3 minutes have elapsed.
thoroughly flushed out with cold water.
Make sure that the pilot is alight and stable, see diagram 7.2 for
Refit the pump and fill the system. Examine for water soundness
the approximate flame length. Switch on the electrical supply.
and vent all air from the system and pump. Make sure that all
Set any remote controls so that they are calling for heat. Turn
valves are open.
control knob  A to ' ' main burner position. Set the thermostat
control knob  B between  MIN and  MAX , the main burner will
7.2 Initial Lighting, Testing and Adjustment
light.  MAX is about 82oC (180oF).
CAUTION. The following procedure should be carried out by a
Test for gas soundness around boiler gas components with a
competent person.
suitable leak detection fluid.
Identify the boiler controls by reference to diagram 7.1.
Ten minutes after lighting, check the burner setting pressure
Check that the gas service cock  K is closed, indicator slot and adjust, if necessary, as follows, remove cover  F , see
vertical. diagram 7.1 and turn adjustment screw anti-clockwise to
decrease, see Data Table or refer to  L Data Label for setting
Make sure that the thermostat phial is fully inserted in the phial
pressure. After adjusting replace cover.
pocket  J and is securely located by the retaining split pin.
If any doubt exists, the gas rate should be checked at the meter.
Check that the mains electrical supply is switched off.
This should be in the range of :- HIDEAWAY 120B 3.5m3/h to
Set thermostat control knob  B to  O .
4.2m3/h (125 to 148 ft3/h)
Remove the burner pressure test point screw  G and connect
Stick the self-adhesive arrow indicator, from the loose items
a suitable pressure gauge.
pack, to the data label against the rating the boiler is going to be
Open gas service cock  K , indicator, horizontal.
set to.
Turn gas control knob  A to' ' pilot/ignition position and
Allow the water system to reach maximum working temperature
and examine for water soundness. The system should then be
depress.
turned off and drained rapidly, whilst still hot, to complete the
At the same time push and release piezo ignition button  C until
flushing process.
the pilot burner lights, view through window  E . At this stage air
The system should then be filled again, vented and examined
may be present in that gas pipes, so this operation may need to
for water soundness.
be repeated several times. When the pilot burner lights, keep
= OFF
= PILOT/IGNITION
C B
L = MAIN BURNER
A
F
N
SETTING
SETTING
POINT
J
J
POINT
M
H
K
K
E
(Shown
(Shown
closed) G
open)
A GAS CONTROL KNOB H CONTROL BOX
B TERMOSTAT CONTROL J PHIAL POCKET
C PIEZO IGNITION BUTTON (alternative positions)
E VIEWING WINDOW K GAS SERVICE COCK
F GOVERNOR ADJUSTMENT L DATA LABEL
COVER M GAS CONTROL VALVE
G BURNER PRESSURE N PILOT ADJUSTMENT
TEST POINT SCREW
Diagram 7.1
BOILER COMPONENTS
15 221765B
9017
7 Commissioning
7.3 Operational Checks
13 (1/2 in.)
SPARK GAP
APPROX.
FLAME
Check operation of the flame failure device as follows, with the
DIMENSION
main burner alight, turn the gas valve control knob  A fully DIMENSION
clockwise to its stop' ' , this will extinguish the main and pilot
burners. The safety device should close before 60 seconds
have elapsed, a click from the gas valve will indicate it has
3-4mm.
closed. Pilot shield
(1/8 in.)
omitted
Remove the pressure gauge and refit the pressure test point
for clarity
screw  G , make sure that a gas tight seal is made.
Turn thermostat  B to  O then relight the pilot burner as
Section 7.1.
Relight the main burner.
VIEWING
Check that the boiler thermostat and all automatic controls are WINDOW
operating correctly.
PILOT
Do not attempt to adjust the thermostat calibration screw.
BURNER
Relight the main burner and check for gas soundness with a
ASSEMBLY
suitable leak detection fluid.
Diagram 7.2
PILOT FLAME DIMENSION
7.4 Completion and User Information
Instruct and demonstrate the efficient and safe operation of the
boiler, heating and hot water system.
Hand the Instructions for Use to the user, for their retention,
STUD
making sure that they are understood.
UPPER
Advise that to ensure the efficient and safe operation of the
HOOK
boiler it is recommended that it is checked and serviced at
DOOR
regular intervals. The frequency of servicing will depend upon
FASCIA
the installation conditions and usage, but in general once a year
VIEW 1
should be enough.
It is that law that any servicing must be carried out by a
competent person.
PLINTH
FRONT
Draw attention, if applicable, to the current issue of the Gas
Safety (Installation and Use) Regulations, Section 35, which
imposes a duty of care on all persons who let out any property
LOWER
containing a gas appliance.
HOOK
Fit the plinth front by locating the sides over the boiler plinth then
VIEW 2
lowering to engage the upper and lower hooks, see diagram
7.3.
Fit the door by locating the hooked runner at the bottom into the
slots in the side casings and pushing on to the studs on the side
casings.
VIEW 1
Reminder - Leave these instructions and the  Benchmark
logbook with the user.
VIEW 2
PLINTH / DOOR FITTING Diagram 7.3
221765B 16
0937
1356
8 Servicing
Before commencing any servicing, turn off the gas supply at the
GAS
gas service cock, see diagram 8.1 and isolate the electrical
SERVICE
supply to the boiler.
COCK
Always test for gas soundness after completing any servicing or
(turn off)
replacement of parts.
(shown
closed)
8.1 Gain Access to the Boiler
Pull the door forward at the top to disengage studs and lift to
release from the slots, see diagram 7.3.
Lift the plinth front up and forwards to withdraw, see diagram
7.3.
If the top casing is removed during servicing care must be taken
not to damage or lose any plastic pegs when replacing it. Refer
to Section 5.3  Top Casing when refitting.
8.2 Boiler Flueways
Unscrew the union nut securing the gas service cock to the gas MAINS INLET
valve, see diagram 8.1.
CONNECTOR
Remove the mains inlet connector by pulling downwards, see (pull downwards)
ISOLATION OF
diagram 8.1
GAS AND ELECTRICITY
Diagram 8.1
Remove split pin on the thermostat phial pocket and withdraw
the phial and capillary, see diagram 4.5.
Remove the five screws retaining the combustion chamber
GRAPHITE
TIE
cover and burner assembly, see diagram 8.2.
COATED NUT
BAR
Ease the gas service cock away from the gas valve and unhook
the pipe support bracket from the tie bar to enable the assembly
of cover, control box, gas valve and burners to be withdrawn
forwards.
Remove graphite coated nut to release baffle tray and remove
from combustion chamber, taking care not or damage the
BAFFLE
insulation material in the sides of the chamber.
TRAY
Remove the self-tapping screws which retain the flueway
cleaning door and lift door clear, see diagram 8.3.
Remove the baffles from the heat exchanger, see diagram 8.6.
PIPE
Place a sheet of paper in the combustion chamber to catch any
SUPPORT
flue debris.
BRACKET
Access for flueway cleaning is made through the cleaning door
and combustion chamber apertures. COMBUSTION
SECURING
CHAMBER
Thoroughly clean boiler flueways and fins from top and bottom
SCREW (5)
with a suitable stiff brush. Remove any debris from the base of COVER
the combustion chamber.
Diagram 8.2
ACCESS FOR SERVICING
Check that the flueways are clear, view with the aid of a mirror
or reflector.
8.3 Burners and Injectors
Refer to Section 8.2 for instructions on how to remove cover,
burners and controls assembly.
FLUEWAY
Remove the two screws and nuts securing each burner support
CLEANING
bracket to the combustion chamber cover, see diagram 8.4.
DOOR
Remove the graphite coated nuts on supply feed pipe at the rear
of the burner to release the burners, taking care not to damage
the pilot burner and shield when removing.
Remove the nuts, washers and burner end caps, see diagram
SELF-
8.5.
TAPPING
Remove the distributors from inside the burners then clean the
SCREW (4)
burners and components thoroughly with a vacuum cleaner.
Check that the main burner injectors are not blocked or damaged.
Clean or renew as necessary. Do not clean with a wire or sharp
instrument, see diagram 8.4.
8.4 Service Checks
Inspect the thermocouple and pilot burner, clean or renew as
ACCESS TO FLUEWAY Diagram 8.3
necessary.
17 221765B
9012
9018
0908
8 Servicing
Check the condition of the insulation panels in the combustion
chamber, renew if necessary.
Check the condition of the seals on the cleaning door and the
combustion chamber cover, renewing if necessary.
8.5 Re-assembly
Make sure that the baffle tray is replaced and secured with the
graphite coated nuts, previously removed.
SECURING
Make sure that the thermostat phial is fully inserted into the phial
NUT
pocket and secured, with the location washer behind the
retaining split pin, see diagram 4.5.
Make sure flueway baffles are positioned as diagram 8.6
BURNER
BURNER
8.6 Operational Checks END CAP
WASHER
Light the boiler and carryout the operational checks as described
Diagram 8.5
BURNER SERVICING
in Sections 7.2 and 7.3.
COMBUSTION CHAMBER
COVER
MAIN
SUPPLY
BAFFLES
BURNER (2)
PIPE
INJECTOR (2)
GRAPHITE
BURNER
SCREW
COATED NUT (2+2)
SUPPORT
(2+2)
BRACKET (2)
Diagram 8.6
REMOVAL OF BURNER HEAT EXCHANGERS
Diagram 8.4
9 Replacement Parts
Before removing or replacing any parts, turn the gas off at the 9.2 Injectors
gas service cock, see diagram 8.1 and isolate the electrical
Gain access to the boiler as Section 8.1
supply to the boiler.
Unscrew the injectors from the manifold and renew as necessary.
ALWAYS test for gas soundness after replacing any gas
When replacing the injectors use a little jointing compound, on
carrying component.
the external thread only, to ensure gas soundness.
Unless stated otherwise replacement of parts is in the reverse
Replace thermostat phial as Section 8.5.
order to removal.
9.3 Thermocouple
9.1 Gas Valve
Gain access to the boiler as Section 8.1.
Gain access to boiler, see Section 8.1.
Disconnect the thermocouple by unscrewing nuts at the gas
Disconnect the gas valve plug, thermocouple nut and pilot tube
valve and pilot burner, see diagrams 9.1 and 9.2. Withdraw the
connections at the gas valve, see diagram 9.1.
thermocouple.
Support the valve and remove the four right-hand flange screws
When replacing tighten the thermocouple nut only a quarter turn
to disconnect the gas valve from the burner supply pipe.
beyond finger tight.
Ease the gas service cock union out and remove the valve
taking care not to damage the  O ring seal at the flange.
9.4 Pilot Burner
Inspect the condition of the  O ring seal and renew if necessary.
Gain access to the boiler as Section 8.1.
Remove the union half and refit into the replacement valve on
Remove the cover and burner controls assembly, as Section 8.2.
the inlet, left-hand side. Use a little jointing compound, on the
Disconnect the ignition lead at the electrode, see diagram 9.2.
external thread only, to ensure gas soundness.
Disconnect the thermocouple nut at the pilot burner.
It will be necessary to purge air from the gas line after changing
the gas valve, refer to Section 7.2. Disconnect the pilot tube nut, ease out the tube and injector
which is hooked on to the pilot tube.
221765B 18
6040
6039
6143
9 Replacement of Parts
Remove the nut retaining the spark electrode and remove.
PILOT TUBE
Remove the two screws and nuts securing the pilot burner and
NUT
shield to the combustion chamber cover.
GAS
Hook pilot injector over pilot tube olive when refitting.
VALVE
Check that the pilot flame length is as shown in
PLUG
diagram 7.2.
Replace thermostat phial as Section 8.5.
9.5 Spark Electrode
GAS
Gain access to the boiler as Section 8.1. GAS
VALVE
OUTLET
Disconnect the thermocouple nut and withdraw thermocouple
from pilot burner, see diagram 9.2. FLANGE
SCREW
Disconnect the nut retaining the spark electrode and remove.
(4)
When re-assembling check that spark gap is as shown in
diagram 7.2
THERMOCOUPLE
9.6 Insulation Panels
NUT
Gain access to the boiler as Section 8.1.
REMOVAL OF GAS VALVE Diagram 9.1
Remove the burner assembly as Section 8.2.
Remove the two screws retaining each side insulation panel
within the combustion chamber and remove panel, see diagram
9.3. SECURING SCREW (2)
AND NUT (2)
Release the rear insulation panel upper clips and lift panel out.
Refit thermostat phial as Section 8.5.
THERMOCOUPLE
SPARK
ELECTRODE
9.7 Boiler Thermostat
Follow the relevant instructions in Section 8.1. IGNITION LEAD
(CLEAR END)
Remove the mains inlet connector by pulling downwards, see
diagram 8.1.
Remove the retaining split pin from the phial pocket then
withdraw the phial and capillary, see diagram 4.5.
PILOT
SHIELD
Pull off the thermostat control knob.
Gain access to inside of the control box by removing the
PILOT
securing screw located at the top of control box and unhooking
PILOT
TUBE
at the bottom, see diagram 9.4.
BURNER
PILOT
Remove the two screws which secure the boiler thermostat to
ASSEMBLY
INJECTOR
the control box, see diagram 9.4.
Tilt the thermostat so that the electrical connections can be
removed.
Diagram 9.2
PILOT ASSEMBLY
Withdraw boiler thermostat from control box complete with
capillary tube and phial.
Refer to diagram 9.5 to connect electrical connectors.
REAR
SIDE
Replace the thermostat phial as the relevant part of Section 8.5.
INSULATION
INSULATION
Make sure that the capillary is positioned so that it passes
PANEL
PANEL
through the cut out in the control box, see diagram 9.4.
9.8 Piezo Unit
Pull door forward at the top to disengage the studs and lift to
CLIP
release from slots, see diagram 7.3.
BAFFLE
Remove mains inlet connector by pulling downwards, see
TRAY
diagram 8.1.
Gain access to inside of the control box by removing the
SCREW
securing screw located at the top of control box and unhooking
at the bottom, see diagram 9.4.
Disconnect the ignition lead at the piezo unit.
Note: To ease the removal of the piezo unit it is advisable to
temporarily remove the boiler thermostat from the control box.
Depress the retaining tabs and remove the Piezo unit.
GRAPHITE
9.9 Ignition Lead
COATED NUT
Gain access to the boiler as Section 8.1.
INSULATION PANELS
Diagram 9.3
Disconnect the ignition lead at the piezo unit, see diagram 9.4
and section 9.8.
19 221765B
9013
0935
1281
9 Replacement of Parts
Disconnect the lead at the spark electrode, see diagram 9.2. Disconnect the gas valve plug from the valve, see diagram 9.1.
When reconnecting lead make sure that the clear end is fitted Release the control box by removing the securing screw located
to the spark electrode. at the top of control box and unhooking at the bottom, see
diagram 9.4.
9.10 Electrical Control Box
Pull the ignition lead off piezo unit, see diagram 9.4.
Gain access to the boiler as Section 8.1.
When refitting control box make sure the thermostat capillary is
Disconnect the mains inlet connector, see diagram 8.1.
positioned so that it passes through the cut out in the control
box, see diagram 9.4.
Remove the retaining split pin from the phial pocket then
withdraw phial and capillary, see diagram 4.5.
Refit thermostat phial, refer to Section 8.5.
ELECTRICAL
CONTROL BOX
COVER
HOOK
THERMOSTAT CUT-OUT FOR
AND CAPILLARY CAPILLARY
COVER
SECURING
IGNITION LEAD SCREW (4)
(BLACK END)
THERMOSTAT
SECURING
SCREW (2)
PIEZO
ELECTRICAL
UNIT
CONTROL BOX
THERMOSTAT ELECTRICAL
CONTROL KNOB CONNECTORS
SECURING SCREW
Diagram 9.4
CONTROL BOX
N L
VIEW OF PLUG
230V~ 50Hz
GREEN/
WHEN REMOVED
E
MAINS SUPPLY
YELLOW
THERMOSTAT
FUSED AT 3A
GAS VALVE
N L
C N/C
CHASSIS
EARTH
BLUE
BLACK
BROWN
CONTROL BOX AND GAS VALVE WIRING Diagram 9.5
221765B 20
7995
6284
GREEN / YELLOW
10 Fault Finding - Electrical
10.1 Electrical
L
GAS VALVE
IMPORTANT, the preliminary electrical system checks as
CONTROL SOLENOID
contained in the British Gas Multimeter Instruction book or
similar publication, are the first checks to be carried out during
THERMOSTAT
a fault-finding procedure. On completion of the service fault-
N L
finding task which has required the breaking and remaking of
N/C
C
electrical connections then checks, earth continuity, polarity
and resistance to earth must be repeated.
E
Refer to functional flow diagram 10.1 electrical fault finding VIEW OF
chart, diagram 10.2 and wiring diagram 9.5.
PLUG
WHEN
REMOVED
BLACK BROWN
N
Diagram 10.1
FUNCTIONAL FLOW WIRING
Carry out preliminary electrical system checks to make sure that the electricity supply is available at the boiler.
Check that any remote time or temperature controls are calling for duty. Make sure that the system is filled,
the gas supply is available and the pilot is lit.
START
Isolate electricity supply at the external isolator. Remove the mains inlet connector and cover to expose
supply cable connections. Reconnect inlet connector, restore power. Is there 220 to 240V between 'L' and 'N'?
YES
NO
Check that all remote time or temperature
Isolate electricity supply to the unit at the
controls are calling for duty.
external isolator. Remove the control box cover.
Check continuity of red cable between terminal
'L' in the inlet connector and Thermostat terminal 'C'.
Is there continuity?
Faulty cable, renew.
NO
YES
Turn boiler thermostat to maximum. Connect
ohmmeter across thermostat terminals 'NC' and 'C'.
Is there continuity?
NO
Faulty thermostat, renew
YES
Turn boiler thermostat OFF.
Is continuity interrupted?
NO
YES
Connect ohmmeter and check the continuity
of brown cable between terminal 'L' on gas
Faulty cable, renew.
valve plug and terminal 'NC' at thermostat.
NO
Is there continuity?
YES
Connect ohmmeter between terminal 'N' in
Faulty cable, renew.
inlet connector and gas valve plug terminal 'N'.
Is there continuity?
NO
YES
Disconnect ohmmeter and reconnect gas valve plug.
Faulty gas valve, renew.
Restore power to unit. Does burner light?
NO
YES
Boiler in order. Isolate electricity supply and
refit mains inlet connector cover.
ELECTRICAL FAULT FINDING Diagram 10.2
21 221765B
4708
BLUE
1526
10 Fault Finding - Thermocouple
Disconnect appliance thermocouple from the multifunctional control. Check that all
connections are clean and in good condition. Fit test meter interrupter into the magnet unit.
Fit appliance thermocouple into the test meter interrupter.
Hold down control tap in ignition position. Ignite burner, allowing thermocouple to attain
operating temperature. Measure the OPEN CIRCUIT voltage.
Is
voltage
NO
Faulty thermocouple.
greater
Replace.
than
15mV?
YES
Note the open circuit reading then measure the CLOSED CIRCUIT voltage. Note this voltage.
Referring to the diagnosis graph, mark the open circuit voltage on the VERTICAL axis,
and the closed circuit voltage on the HORIZONTAL axis. Note the point where these
two values intersect on the graph.
In
which
B A
THERMOCOUPLE
area of the Faulty thermocouple.
CIRCUIT IS
graph is the
Replace.
SATISFACTORY intersect
C
Faulty magnet unit in gas tap.
Replace multifunctional control.
THERMOCOUPLE FAULT FINDING Diagram 10.3
10.2 Thermocouple
29
To test the thermocouple a meter with a range of 0 to 30mV is
27
required together with a thermocouple interrupter similar to the
Minitest 6 Multimeter and interrupter. 25
Refer to thermocouple fault finding chart, diagram 10.3 and
23
diagnosis graph, diagram 10.4.
21
ABC
10.3 Pilot
19
Refer to pilot fault finding chart, diagram 10.5.
17
15
13
11
9
0 2 4 6 8 10 12 14 16 18 20 22
Closed Circuit Voltage (millivolts)
DIAGNOSIS GRAPH FOR
THERMOCOUPLE CIRCUIT
Diagram 10.4
221765B 22
6042
1546
Open Circuit Voltage (millivolts)
10 Fault Finding - Pilot
PILOT WILL NOT LIGHT
START HERE
Does pilot stay alight when
Check gas line-open all cocks,
gas valve knob is released?
rectify any blockages, purge out
any air. Does pilot light?
NO YES
NO
YES
Apply match to pilot burner instead
of pressing piezo unit button. PILOT SATISFACTORY
Does pilot light?
NO YES
Undo tubing nut at pilot burner.
Turn gas valve knob to Pilot/Ign.
Does pilot flame envelop
Press gas valve knob.
thermocouple?
Does gas flow freely?
NO
YES
YES
NO
Check aeration. If necessary - Clean
Rectify blockage in pilot injector,
pilot, rectify blockage in pilot
or renew pilot injector.
injector, or replace.
Undo tubing nut at pilot outlet
Check thermocouple circuit using
of gas valve. Press gas valve knob.
Thermocouple and Boiler Overheat
Does gas flow freely?
Cut-Off fault finding.
YES
NO
On pressing piezo unit button is
Change blocked pilot tube.
there a spark across electrode
gap?
NO
YES
Pull ignition lead off electrode.
Change gas valve.
Hold end of lead close to pilot
burner and operate piezo unit.
Is there a spark across gap?
NO
YES
Pull ignition lead off piezo unit.
Using blade of a screwdriver, touch
unit chassis and leave approx.
4mm gap from connection tag on
piezo unit. Operate piezo.
Is there a spark across gap?
NO
YES
Change Change
piezo unit. ignition lead.
Check electrode gap. Reposition,
or replace electrode as necessary.
BOILER PILOT FAULT FINDING Diagram 10.5
23 221765B
0905
11 Spare Parts
When ordering spare parts please quote the part number and
description, stating the model and serial number, from the data
label  L , see diagram 7.1.
If ordering from British Gas also quote the GC number of the
part and appliance.
1
2
3
11
12
7
5
4
10
8
9
6
Diagram 11.1
Key No Part No Description GC No
1 203377 Gas control valve 394151
2 205746 Injector (2) *** ***
3 203414 Pilot burner 312 426
4 203508 Injector - pilot 395 674
5 202407 Thermocouple c/w nut 392 850
5 202415 Thermocouple c/w nut
6 202571 Thermostat c/w screws
7 204687 Control knob assy - thermostat
8 202713 Piezo unit
9 WW4609 Ignition lead assembly 136 464
10 202605 Spark electrode 395 720
11 208302 Sight glass 312 419
12 212031  O ring - gas valve 312 602
Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.
221765B 24
9014


Wyszukiwarka

Podobne podstrony:
Glow Worm installation and service manual Hideaway 60CF UIS
Glow Worm installation and service manual Hideaway 100CF UIS
Glow Worm installation and service manual Hideaway 50BF UIS
Glow Worm installation and service manual Hideaway 80CF UIS
Glow Worm installation and service manual Hideaway 80BF UIS
Glow Worm installation and service manual Hideaway 70CF UIS
Glow Worm installation and service manual Hideaway 70BF UIS
Glow Worm installation and service manual Hideaway 40BF UIS
Glow Worm installation and service manual Hideaway 120CF UIS
Glow Worm installation and service manual Hideaway 50CF
Glow Worm installation and service manual Hideaway100BF UIS
Glow Worm installation and service manual Hideaway 40CF
Glow Worm installation and service manual Ultimate 60CF UIS
Glow Worm installation and service manual Ultimate 60BF UIS
Glow Worm installation and service manual Miami GF UIS
Glow Worm installation and service manual Ultimate 50CF UIS
Glow Worm installation and service manual Ultimate 40BF UIS
Glow Worm installation and service manual Ultimate 50BF UIS
Glow Worm installation and service manual Ultimate 40CF UIS

więcej podobnych podstron