TECHNICAL INFORMATION
Product
HM1202, HM1202C
Models No.
P 1 / 14
112mm(4-3/8")
Description
Demolition Hammers
CONCEPTION AND MAIN APPLICATIONS
These demolition hammers are newly developped
as a 10 Kg hammer. (middel class between
HM1201 and HM1303 series models.)
Considerable strong demolishing power in this class,
However, softened reaction.
Model HM1202C : equipped with electronic control system
and variable speed control dial.
Model HM1202 : without the above features.
Specifications
Continuous Rating (W)
Max. Output(W)
Current (A) Output
Voltage (V)
Cycle (Hz)
Input
HM1202 HM1202C HM1202 HM1202C HM1202 HM1202C
100 15.0 1500 1600
15.0 700 500
1500
14.0 15.0 1600
110 700 500
120 1500
13.0 13.0 700 500 1600
1,450
50/60
220 6.8 1600 1800
7.3
750 550
6.5 7.0 1600
230 750 550 1800
750 550
6.7 1600 1800
240 6.3
Bit-type SDS-Max
950-1900 (bpm)
HM1202C
Blows per minute
HM1202 1900 (bpm)
Net Weight 9.3kg (20.5 lbs)
18mm (11/16")
Size of shank
Cord Length
5m (16.4 ft)
Standard equipment
Bit Grease
Bull-Point 280
Optional accessories
Bull Point 280 Scaling Chisel 50x400
Bull Point 400 Clay Spade 105x400
Cold Chisel 25x280 Hammer Grease
Cold Chisel 25x400
The standard equipment for the tools shown may differ form country to country.
258mm(10-1/8")
578mm(22-3/4")
P 2 / 14
Repairing
Screwdriver
<1> Dismounting of armature
(1) Take off the rear cover from the motor housing
by loosening 2 pcs.of tapping screw M4x18.
And then take off the carbon brushes after
taking off the brush holder cap.
Brush Holder Cap
Tapping screw M4x18
(2) Take off the handle and controller cover
by loosening 2 pcs.of hex socket hd.bolt M6x40
Hex socket hd.bolt M6x40
and 4 pcs.of hex socket hd.bolt M6x30.
Hex socket hd.bolt M6x30
Controller cover
(3) Dismount the motor housing by loosening
4 pcs.of hex socket hd.bolt M6x40.
Hex socket hd.bolt M6x40
Motor housing
(4) Support the machine with the repairing jig No.1R023,
Arbor press
1R218 and 1R022.
Put a round stick (repairing jig No.1R234 or 1R235)
on the armature
The armature can be dismounted from the
1R234 or
motor housing by pushing the above round stick
1R235
with arbor press.
1R022
1R218
1R023
Armature
Base of arbor press
P 3 / 14
(5) Dismounting of ball bearing 6304LLU from crank shaft.
Insert the repairing jig 1R234, 1R240 and 1R241 into the arbor on the crank shaft as per
the following illustration. And then, press with arbor press. So, Ball bearing 6304LLU can be dismounted.
Arbor press
1R032 - 1R037
1R234
1R240
1R241
Crank shaft
1R034
Ball bearing 6304LLU
Base of arbor press
(Mounting)
Make sure that the gears interlock each other, before pressing the armature
with arbor press into crank housing.
Arbor press
<2> Repairing on chuck section
Repairing on chuck section has to be made
with installing controller cover, because it is difficult
to keep the machine standing without it.
Tool holder cap
(Dismounting)
(1) Pull tool holder cover down in the direction
of the motor housing.
Dismount tool holder cap.
And then take off tool holder cover.
Tool holder cover
P 4 / 14
(2) Take off ring spring 25 and retaining ring WR-45
with repairing tool No.1R212.
Then, the spare parts on the chuck section can
1R212
be dismounted in the order from the bit side.
Retaining ring WR-45
Cup Washer 45
Compression spring 55
<3> Repairing of piston and striker
Take off only handle, not remove controller cover.
(Dismounting)
(1) Take off change ring after dismounting of chuck section.
And then, take off ring spring 46
with pawl for retaining ring .
Dismount housing cover.
Ring spring 46
Housing cover
Pawl for retaining ring
(2) Loosen 4 pcs. of hex socket head bolt M8x30.
Then barrel can be removed together with
tool holder.
Hex socket head bolt M8x30
(4 pcs.)
Barrel
(3) Hold cylinder liner 44 with hand and P 5 / 14
strike crank housing with plastic or wooden
hammer.
Then the cylinder liner 44 can be removed from
the machine.
Cylinder liner 44
Crank housing
(Mounting)
Mount slide sleeve 49, ring 49 and
compression spring 50 on cylinder liner 44.
Striker
And then, put the cylinder liner 44 on piston.
Mount the cylinder liner to the crank housing
Cylinder liner 44
by pressing it with hand.
Insert striker into the cylinder liner from
the bit-installing side.
Slider sleeve 49
Ring 49
Compression spring 50
Piston
Crank housing
<4> Repairing of tool holder
Take off only handle, not remove controller cover.
(Dismounting)
Take off flat washer 37 after removing
Tool holder
ring spring 34.
Remove tool holder from barrel by pressing .
Ring spring 34
Flat washer 37
Barrel
P 6 / 14
(Mounting)
(1)Make sure that urethane ring 43 and O ring 38 are
mounted on tool holder in dvance. If not, mount
them on the tool holder.
Insert impact bolt into tool holder, and mount the
tool holder in barrel.
Barrel
Tool holder
Impact bolt
O ring 38
Urethane ring 43
(2)Mount flat washer 37. At this time the side marked with [ UP]
has to be faced upside.
And then, fix the flat washer 37 with ring spring 34.
Flat washer 37 Steel ball 5.6
The side marked with [ UP]
Impact bolt
UP
Hammer bit side
Crank housing
side
Tool holder
Ring spring 34
Barrel
< 5> Mounting of fluoride ring
P 7 / 14
(Mounting)
(1) Fluoride ring 28, just after mounted, can not be fit
precisely along the groove on the impact bolt.
The edge come out from the groove.
(2) Insert the impact bolt on which the fluoride
ring 28 is attached, into repairing jig No.1R-214.
At this time the impact bolt has to be inserted
from the hole for [HR5001C]
And then, keep the impact bolt in the repairing jig
approx. 10 sec for correction of fluoride ring 28.
(3) Pay attention, not to damage fluoride ring 28, when
the impact bolt is inserted into tool holder.
Fluoride ring 28
Fluoride ring 28 corrected
of which edge has come out
with repairing jig No.1R-214
from the groove.
Hole for
[HR5001C]
O ring 23
O ring 23
Repairing jig No.1R-214
(Taper sleeve)
HR5001C
HR4000C
P 8 / 14
< 6> Mounting of barrel
Take off only handle, not remove controller cover.
(1) Set the of the guide ring on the of flat washer 49.
Mount the above guide ring and flat washer 49 on the 3 prongs
of slide sleeve 49.
(2) Set collared ring 24 ,rubber ring 25 and impact bolt guide
on the 3 prongs of slide sleeve 49.
(3) Set barrel (with tool holder) on the cylinder liner 44 gently paying attention
to keep rubber ring 25 and impact bolt guide on the slide sleeve's edge.
Mount compression spring 50 on crank housing by pressing it.
< Remarks>
Pay attention to the position of flat part on barrel as per the following illustration.
Tool holder
Barrel
Impact bold guide
Rubber ring 25 Guide ring
Flat washer 49
Slide sleeve 49
Flat part on barrel
has to face in the direction
Compression spring 50
of top and bottom.
Collared
sleeve 24
Cylinder liner 44
Crank housing
< 7> Mounting of controller cover
Set switch trigger in of switch lever.
I
ON
P 9 / 14
< 8> Grease
Change of grease
Change grease to fresh one when carbon brush is changed.
(1) Idle the machine for several minutes in order to warm up.
(2) Take off the handle and controller cover
by loosening 2 pcs.of hex socket hd.bolt M6x40
and 4 pcs.of hex socket hd.bolt M6x30.
And then, crank housing appears.
Hex socket hd.bolt M6x40
Hex socket hd.bolt M6x30
Handle
Controller cover
Crank Cap
(3) Take off crank cap.
Crank Housing
(4) Gather the grease softened by warming up, into
the crank housing by facing the tool holder cap side
to upward.
(5) Wipe out the grease
in the crank housing
with cloth. And then, apply fresh MAKITA grease
No.00 by 30g.
< Remarks >
The fresh grease to be applied has to
be limited to 30 g.
Over application can be cause of trouble.
P 10 / 14
The parts to be greased
The parts to be greased are marked with
(1) The parts to be greased with MAKTA grease No.00.
Impact bolt : Inner side of O ring, Out side of fluoride ring 28,
Whole part of impact bolt.
Fluoride ring 28
O ring
Striker : O ring 34,
Whole part of striker
Striker
O ring 34
Piston : O ring 34,
Whole part of piston
O ring 34,
Piston
Rod : Inside of the holes where piston pin
and crank shaft are installed.
Oil seal 17 : Whole of inside
P 11 / 14
Cylinder liner 44: Surface marked with
Ring 49
Slide sleeve 49
Cylinder liner 44
Barrel : Inner part marked with
Crank shaft : Whole of gear part marked with
(2) The parts to be greased with MAKTA grease No.2.
Tool holder
Pin 8
Hole for steel ball 5.6 (Barrel)
Hole for roller 8 (Tool holder)
P 12 / 14
Circuit diagram
HM1202C with controller
This terminal is to be
Black
connected to brush holder
mounted on opposite side
Brush holder on control dial side
of control dial.
>
Black
F2. White
r3. White
Tube
r2. Black
Controller
3
1
CT5 CT4
6 4
CT2
P1.
CT1
CT3
Switch
P2.
r1. Red
Power supply cord
F1. Black
Pick up coil
HM1202 without controller
Black
Black
F2. White
F1. Black
Noise suppressor
C1. White
3
1
Switch
6 4
P1.
P2.
In some countries,
C2. White
Noise suppressor is not
Power supply cord
used.
Circuit diagram
P 13 / 14
HM1202C with controller
Lead wire "r1(Red)" has to be guided
through rib A as per the
illustration.
Rib A Lead wire "r1"(red)
Lead wire from field (F1.Black)
and (F2. White) has to be fixed
by lead holder as per the illustration.
F2. White
F1.Black
Lead wires of pick up coil have to
be guided through rib B.
At this time these 2 lead wires have not
Rib B
to be crossed each other.
Lead wire "r2. black" and
"r3. white" have to be set
in the groove as per the
illustration.
Cord from power supply
cord has to be set in
Cord from power supply cord,
the groove.
Boss A
lead wire "r2. black" and
"r3. white" have to be guided
through the space between boss A
and rib C.
Cord from power supply cord,
Controller
Rib C
lead wire "r2. black" and
Rib D "r3. white" have to be
set in the groove on the right side
of controller.
Every lead wires have to be
set in the space between rib D
and rib E.
Cord from power supply cord,
lead wire "r2. black" and
"r3. white" have to be
Boss B
guided through the space
Rib E
between boss B and rib D.
HM1202 without controller P 14 / 14
Lead wire F1. Black and F2. White
Power supply cord has to be
from field have to be set in the groove.
set in the groove.
F2. White
F1.Black
Power supply cord
Condenser
Wyszukiwarka
Podobne podstrony:
6795D TEBTD140 TEUR3000 TEHP2040 TE9404 TEEA3500F TEBTD042 TE1911B TE9057S TETMG3200 TE4340CT TEKUHARSKI TEČAJ 23 VELIKONOČNI JEDILNIK6016D TE4305t TEwięcej podobnych podstron