{Change Comments ***********************************************************}
{5/9/89
Copied & modified: Fanuc 11M M007.54
For: Tower Mfg Co
Added PreTool.
Changed OfstOff to literal 'G30Y0.Z0.' at FirstOperation, NewTool and end of Prog.
Changed OfstOff to literal 'G30Z0.' at SameTool.
JR}
{8/28/89
Modified: Fanuc 11M MTS M203.55
For: Tower Mfg Co
Added sperate sub codes.
JR}
{11/10/89
Updated: Fanuc 11M MTS M203.56
For: Gibbs & Associates
Updated per Fanuc 6M M001.61 Format.
JR}
{3/26/90
Updated: Fanuc 11M MTS M203.61.
For: Gibbs & Associates
Updated to Version 3.2 per Fanuc 6M M001.70.4 Format.
DWB}
{4/16/90
Updated: Fanuc 11M MTS M203.70.4
For: Gibbs & Associates
Updated per Fanuc 6M M001.71.1 Format.
JR}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{2/22/91
Updated: Fanuc 11M MTS M203.72
For: Gibbs & Associates
Updated to Version 3.4 per Fanuc 6M M001.76.3 Format.
DWB}
{4/2/91
Updated: Fanuc 11M MTS M203.76.3
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
KM}
{12/14/93
Modified: Fanuc 11M MTS M203.79
For: Gibbs & Associates/Tower Mfg Co
Updated to Version 4.2 per Fanuc 6M M001.81.2c Format.
Added variable Drill Depths at ToolPath.
Added IF FIFO? for Milling.
Added TrackZNO# ZDepth# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
Corrected FORMAT for Dwell# from '####^###;' to '####^##0'.
Moved UnSkipZ from FinishSub1 to ZOnlyRep where SkipZ is set.
Changed FeedRateC to FeedEntC to FIFO Exit Moves.
Added RestoreScale Sub per 4-Axis Post Processor.
Changed TrackZNO# ZDepth# to TrackZNO# FIRST SPZ# at IF Drilling.
SPZ# is affected by SetScale, whereas ZDepth# is not.
Added CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Changes made per per customer bug report, sample ncCam document and output file supplied by
Tower Mfg Co
Added StrtPosC at AutoCycCutSub2.
Temporary fix for incorrect condtional SetPass2 AutoCycle Position Pattern.
DWB}
{1/14/94
Modified: Fanuc 11M MTS M203.81.2
For: Tower Mfg Co
Versions: ncCad 4.32/ncCam 4.32/ncPost 4.32.01/Compost4.21.19
Changes made per customer bug report noted on 12/14/93.
Deleted StrtPosC at AutoCycCutSub2.
AutoCycles work again.
DWB}
{2/9/96, Updated .81 version to .84, MPK}
{3/22/96, Tested ZOnlyRepAutCycle, Incremented number to .87, MPK}
{7/19/96,
Initial: Fanuc 11M MTS M203.87
Created: Fanuc Longhand 11M Mxxx.13
Modified per Longhand M001.12 for longhand output
Updated to .13 format
Added literal 'G54' output in safe start block when NoMPs or Equally spaced.
Changed WFOStuff to only output when MP WorkfixtureOffsets.
Moved Speed SpinOn to After OffstOn block in FirstOp4 and NewToolOp6
Moved PreTool to same line as CoolOn in FirstOp4 and NewToolOp6
Eliminated SpinOff when not changing tools at home in NewToolOp3 and End2
Added literal 'M01' to OfstOn line in FirstOp4 and NewToolOp6
MPK}
{1/15/97
Initial: Fanuc 11M MTS LH M059.13
Created: Fanuc 11M MTS LH M059.13.1
ForUser: Rockwell Cedar Rapids
Develop: ComPost2 MSL 68K, Virtual Gibbs 3.23
Comment: Added missing FirstOp4 and NewToolOp6 calls to NoMPs sub.
Jim Radcliffe}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
#8 = 'Ä…#bbbb.bbbb#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ADD#,4)
FORMAT(TrackZNO#,4)
FORMAT(ToolDiameter#,4)
FORMAT(Recall#,5)
FORMAT(Tag#,5)
FORMAT(Program#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)
FORMAT(PartShiftX#,8)
FORMAT(PartShiftY#,8)
FORMAT(PartShiftZ#,8)
{Prog Subroutines **********************************************************}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' Tag# ' )' EOL
END
RETURN
DoCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN
BadMPWFOReport:
SetStatusOff
' ' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
'Ä„ NOTE: Even though you have elected to Ä„' EOL
'Ä„ process this file using Multiple Ä„' EOL
'Ä„ Parts with Work Fixtures, there exist Ä„' EOL
'Ä„ non-zero values in the invisible, Ä„' EOL
'Ä„ Equally SpacedÉ fields, as follows: Ä„' EOL
'Ä„ Ä„' EOL
'*****************************************' EOL
IF NotEqual? PartShiftX# Num#('0')
' X axis shift = ' PartShiftX# EOL
END
IF NotEqual? PartShiftY# Num#('0')
' Y axis shift = ' PartShiftY# EOL
END
IF NotEqual? PartShiftZ# Num#('0')
' Z axis shift = ' PartShiftZ# EOL
END
'*****************************************' EOL
'Ä„ Ä„' EOL
'Ä„ Please reset these values to zero as Ä„' EOL
'Ä„ they affect the coordinate values Ä„' EOL
'Ä„ output, starting with Part# 2. Ä„' EOL
'Ä„ Thank You. Ä„' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
' ' EOL
SetStatusOn
RETURN
PSInit:
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN
PSStuff:
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF
END
RETURN
DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN
ExitMove:
SeqC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN
ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN
CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
SetFlag('1') { CRCOffsetC }
CRCOnC
END
END
RETURN
FormatLine:
ckCRC FeedC MoveXYZC
RETURN
ckCRCNum:
IF Flag?('1')
SetFlagF('1')
CRCOffsetC
END
RETURN
ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat? { Drilling Only }
SeqC MoveSXYZC EOL
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatLine FeedRateC ckCRCNum EOL
DecelMove2
END
SeqC FormatLine DecelFeed ckCRCNum EOL
ELSE
SeqC FormatLine FeedRateC ckCRCNum EOL
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN
AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
IF Repeats? AND ZShiftOnly?
EntryMove
END
Seq IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN
Milling:
EntryMove
ToolPath
RETURN
XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
CRCOffC
IF FeedConnect?
IF SPXMove? OR SPYMove?
SeqC FeedC MoveSXYC FeedEntC EOL
END
IF ZShiftOnly?
EntryMove
END
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
IF FeedEntry?
SeqC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN
NoRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN
XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN
ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
EachRep
IF NOT FirstCycle?
IF FeedConnect?
SeqC AbsOrInc EOL
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
ELSE
AbsOrInc
ExitMove
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
IF FeedEntry? AND NOT FIFO?
SeqC ZCP2 EOL
END
END
EntryMove
SeqC IncValue EOL
END
EntryMove
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN
DrillStuff:
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# FIRST SPZ# {.81.2}
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
ProgStart:
InitProg
TagInit
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000')
SetMaxFeed('500')
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
OpGuts:
IF Milling?
SeqC ZCP2C EOL
IF AutoCycle?
IF Repeats?
IF ZShiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
DoCycleComment
IF FirstCycle?
DrillStuff
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
SetDrillEndOpZ
SeqC Rapid 'G80' ZCP3 EOL
END
END
RETURN
WFOStuff:
IF MultipleParts? AND WorkFixtureOffsets? AND NewWFO?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS AND WORK FIXTURE OFFSETS' EOL
ELSE
IF NewWFO?
SeqC 'G' NewWFO# EOL
ELSE
IF MultipleParts? AND WorkFixtureOffsets? AND NOT SameTool?
FORMAT(ADD#,5)
SeqC 'G' ADD# NewWFO# SUB# Tag# Num#('1') EOL
FORMAT(ADD#,4)
END
END
END
RETURN
ResetWFO:
IF WorkFixtureOffsets?
SeqC WFO1 EOL
END
RETURN
InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
RETURN
FirstOp1:
Seq Plane
IF MultipleParts?
IF NOT WorkFixtureOffsets?
'G54'
END
ELSE
'G54'
END
'G80' CRCOff EOL
SeqC IncValue 'G30Y0.Z0.' EOL
DoPostScript
SeqC OpToolID EOL
SeqC ToolChng EOL
DoPartCycleComment
DoOpComments
RETURN
FirstOp2:
RETURN
FirstOp3:
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
RETURN
FirstOp4:
SeqC OfstOn 'M01' EOL
SeqC Speed SpinOn EOL
SeqC CoolOn
IF NOT LastTool?
PreTool
END
EOL
RETURN
NewToolOp1:
SeqC CoolOff EOL
SeqC IncValue 'G30Y0.Z0.' EOL
RETURN
NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SetAbs
LoadFeat
SUB# HomeX# CurOriginPosX#
SUB# HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC Rapid MoveXY SpinOff EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN
NewToolOp3: {Start new Operation}
DoPostScript
SeqC OpToolID EOL
SeqC ToolChng EOL
DoPartCycleComment
DoOpComments
RETURN
NewToolOp4:
RETURN
NewToolOp5:
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
RETURN
NewToolOp6:
SeqC OfstOn 'M01' EOL
SeqC Speed SpinOn EOL
SeqC CoolOn PreTool EOL
RETURN
SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC IncValue 'G30Z0.' EOL
SeqC SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC IncValue 'G30Z0.' EOL
END
END
RETURN
SameToolOp2: {Start new Operation}
DoPartCycleComment
DoOpComments
DoPostScript
CheckPass
RETURN
SameToolOp3: {Start new Operation}
IF LAST ProgStop?
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC OfstOn EOL
SeqC CoolOn EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF NewToolOffset?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN
End1:
SeqC CoolOff EOL
SeqC IncValue 'G30Y0.Z0.' EOL
RETURN
End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SetAbs
LoadFeat
SUB# FIRST HomeX# CurOriginPosX#
SUB# FIRST HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC Rapid MoveXY SpinOff EOL
END
IF ProgStop?
SeqC 'M0' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqC ProgStop EOL
END
END
RETURN
End3:
SeqC EOP EOL
EOR EOL
Post
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN
MPallTools1P: {Multiple Parts, All Tools 1 Part}
IF FirstOperation?
IF FirstPart?
InitOp
END
OpenMP
FirstOp1
WFOStuff
FirstOp2
FirstOp3
FirstOp4
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
NewToolOp6
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
WFOStuff
FirstOp2
OpenMP
FirstOp3
FirstOp4
END
ELSE
IF NewTool?
IF FirstPart?
NewToolOp1
CloseMP
ResetWFO
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
OpenMP
NewToolOp5
NewToolOp6
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp3
FirstOp4
OpenMP
END
ELSE
IF NewTool?
IF FirstPart?
CloseMP
NewToolOp1
ResetWFO
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
NewToolOp6
OpenMP
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN
NoMPs: {no multiple parts}
IF FirstOperation?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp3
FirstOp4
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
NewToolOp6
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
WFOStuff
SameToolOp3
END
END
OpGuts
RETURN
MasterSub:
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
RETURN
EndPartSub:
{End of program ************************************************************}
{finish last operation}
IF MultipleParts?
IF AllToolsOnePart?
End1
End2
CloseMP
ELSE {implied OneToolAllParts?}
IF FullUp?
End1
CloseMP
ResetWFO
End2
ELSE {implied ExitClearancePlane?}
CloseMP
End1
ResetWFO
End2
END
END
ELSE {NoMPs}
End1
End2
END
RETURN
DoNewPart:
IF NOT FirstPart?
{Finish off last Part}
IF FullUp?
SeqC CoolOff EOL
SeqC IncValue 'G30Y0.Z0.' EOL
END
{DoEndOpPS}
{Start new Part}
DoPartCycleComment
DoOpComments
DoPostScript
WFOStuff
CheckPass
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF FullUp?
SeqC OfstOn EOL
SeqC CoolOn EOL
END
END
RETURN
DoParts:
TagInit
EachPart
TagInc
EachOp
IF AllToolsOnePart?
MasterSub
ELSE { OneToolAllParts }
IF GTEqual? Operation# Recall# Num#('1') { Tool First Op }
IF LTEqual? Operation# Recall# Num#('2') { Tool Last Op }
IF Equal? Operation# Recall# Num#('1') { Tool First Op }
DoNewPart
END
MasterSub
END
END
END
NextOp
IF AllToolsOnePart?
EndPartSub
END
NextPart
RETURN
GetToolFirstOp:
Save# Num#('2') Recall# Num#('1')
RETURN
GetToolLastOP:
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
RETURN
MPLoop:
IF AllToolsOnePart?
DoParts
ELSE { OneToolAllParts }
GetToolFirstOp
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
GetToolLastOP
DoParts
Save# Num#('1') ADD# Recall# Num#('2') Num#('1') { Next Tool First Op }
END
END
RETURN
{Start of executable Prog, Top Level ****}
ProgStart {setup and initializations}
IF MultipleParts?
IF WorkFixtureOffsets?
{'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'Therefore, the output will be controlled by the following values that are' EOL
'already entered in Equally Spaced Offsets Edit Fields:' EOL
'X' PartShiftX# ' Y' PartShiftY# ' Z' PartShiftZ# EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL}
IF NotEqual? PartShiftX# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftY# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftZ# Num#('0')
BadMPWFOReport
END
END
END
END
EachOp
IF FirstOperation?
Save# Num#('1') Operation#
ELSE
IF LastOp?
Save# Num#('3') Operation#
END
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
ELSE
ResetWFO
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
End3
Wyszukiwarka
Podobne podstrony:
Fanuc 11M MTS [RC] NMQ54 13 1Fanuc 11M Demo LH [TI] MU21 89Fanuc 11M MTS C203 12Fanuc 11M MTS M203 87Fanuc 11M MTS [CSD] M410 15Fanuc 11M LH [RM] CU59 16 1Fanuc 11M Acromax M098 13Fanuc 11M LH [JBT] DW53 15Fanuc 11M LH [JBT] DW53 15Fanuc 15M MTS [CP] NDU66 16 2mFanuc 11M [TM] CQ07 16 2Fanuc 11M MS [HM] M433 80Fanuc 11M Okuma M124 87Fanuc 11M [EDMP] MW52 89Fanuc 11M Toyoda [GS] MU04 89Fanuc 11M [FA] MZ02 89Fanuc 11M [JBT] M142 89 4Fanuc 0M LW LH [RI] CU58 16więcej podobnych podstron