B3EG0RK1 - 607
REMOVAL - REFITTING STEERING COLUMN
1 -
REMOVAL
Push the driver's seat back as far as possible
.
Switch off the ignition
.
Remove the battery style cover
.
Disconnect the battery negative cable ; Protect the cable and the negative terminal to prevent any contact
.
Disconnect the negative cable from the battery in the boot (according to specification) Protect the cable and the negative terminal to prevent any contact
.
REMOVE THE FLOOR CONSOLE
.
Disconnect the (1) 50-way connector (OR)
.
Position the front wheels straight ahead
.
Position the steerng column in the low outlet position and lock it
.
Remove the bolts (1)
.
Remove the trim (2)
.
IMPERATIVE :
push the knob (3) to immobilise it in relation to lateral movement of the steering column (knob travel (3) = 1 mm)
.
Remove the bolt (4)
.
Release the steering universal joint by moving aside the safety clip (5)
.
REMOVE THE AIRBAG
.
Mark the position of the steering wheel in relation to the top suspension unit
.
Lock the steering lock
.
Unscrew a few threads of the steering wheel securing bolts
.
Release the steering wheel from its splines by tapping the rim with your hands
.
Remove the steering wheel securing bolts
.
Mark the steering wheel and mark the column in order to ensure the correct position of the wheel in relation to the column on refitting
.
Remove the steering wheel carefully without pulling out the supply connector (6)
.
Move aside The steering column half shroud (7)
.
Disconnect the connections (8), (9)
.
Using a screwdriver, unclip and pull the analogue module (10), detach it from the steering wheel ignition lock and allow it to hang
.
Unclamp and disconnect the connector (11)
.
Remove the bolts (12) from the lights / wiper stalk bracket
.
Move aside The stalk bracket (13)
.
Disconnect the connectors (14) (15)
.
Unclamp and disconnect the connector (16)
.
DYNAMIC STABILITY CONTROL
Unclamp and disconnect the connector (17)
.
Unclamp and disconnect the connector (18)
.
ALL MODELS
Remove The stalk bracket (13)
.
Remove the bolt (19)
.
Move aside the bracket (20)
.
Disconnect the connectors (21), (22), (23)
.
DYNAMIC STABILITY CONTROL
Remove the drive ring (24)
.
ALL MODELS
Remove the bolt (25)
.
Remove the nuts (26)
.
Grasp the steering column assembly and pull towards you in order to detach the rear part of the column bracket
.
Remove the steering column assembly
.
Remove the securing bolts (27)
.
Move aside the accelerator pedal and its bracket
.
Remove the bolts (28)
.
Remove the seal (29)
.
Remove the bolts (30)
.
Remove the steering column shaft, including the lower universal joint (31)
.
2 -
REFITTING
Proceed in the reverse order to removal
.
When refitting the steering column on its bracket, observe the following order of operations
:
screw on without tightening the nuts (26) and the bolt (25)
position the steerng column in the low outlet position and lock it (32)
tighten the nuts (26) to 2.5 da.Nm
tighten the bolt (25) to 2.5 da.Nm
IMPERATIVE :
when coupling the lower pin (31) and the steering column, do not rotate the lower pin (31)
.
Refit the bolt (4)
.
Tighten the bolt (4) to 2.5 da.Nm
.
Pull the knob (3)
.
Continue the fitting operations in the reverse order to removal
.
DYNAMIC STABILITY CONTROL
When refitting the wiper / lights stalk bracket (13) place the drive ring (33) of the steering wheel sensor in place in the lugs (34)
.
Replace the drive ring and wiper / lights stalk bracket assembly while at the same time engaging it in the grooves of the steering column
.
ALL MODELS
Fit The stalk bracket (13)
.
REFIT AND ADJUST THE ROTARY CONNECTOR
.
Respect the marks made on dismantling
.
Continue the fitting operations in the reverse order to removal
.
2 - 1 -
ACTIVATION : CENTRALISED SYSTEM FOR AIRBAG(S) AND SEATBELTS
IMPERATIVE :
the surroundings of the air bags and the pre-tensioning seat belts must be clear of objects or occupants
.
Switch off the ignition
.
Connect the battery negative cable
.
Driver's side, door open, switch on ignition, while keeping clear of the deployment zone of the steering wheel module
.
Check the correct operation of the system by means of the graphic on the instrument panel
.
3 -
REFITTING (CONTINUED)
Check that the electrical accessories operate correctly
.
Carry out the initialisation procedure for the injection ignition control unit, Using the TEP/DIAG 2000 diagnostic equipment
.
DYNAMIC STABILITY CONTROL
Programme the steering wheel angle sensor using the diagnostic equipment DIAG 2000
.
ALL MODELS
Tightening torques
:
bolt fixing (30) : 2.5 da.Nm
cross member fixing seal : 0.6 da.Nm
steering column to bracket 2.5 m.daN
steering column universal joint fastener : 2.5 da.Nm
steering wheel fastener : 3.5 da.Nm + loctite LOCTITE FRENETANCH
Wyszukiwarka
Podobne podstrony:
B3EG0RK2B3EG0RK1B3EG0RK5B3EG0RK4B3EG0RK7więcej podobnych podstron