43
CABINET BATHROOM
Copyright 2004 Martian Auctions 198
Start At the Top
The first thing I needed was a moulded sink top. It measured 19" x 31" and
was the starting point for the project.
My design includes what I call extended cabriole legs on the front,
creating an elegant, old-fashioned look. I used sugar pine for these legs. It s a little harder than
eastern white pine, but it s still easy to work with. The outline of the 1/4"-thick hardboard template
I made for the leg profile is on this illustration.
Creating cabriole legs is within the reach of most woodworkers. The plans include step-by-
step directions. The technique is quite straightforward but you ll need access to a bandsaw and
the patience to sand the inside and outside curves that form each leg. This is where pine makes
life easier than hardwood.
Once you ve got two front legs and the straight back legs done, it s time to tackle the side
panels. Although most bathroom cabinets are 32" tall, I went with 36". This is reflected in the
materials list. To shorten this cabinet to a standard height, reduce the side stiles, door stiles and
upper portion of the legs by 4".
The plans show the stiles and rails joined into a frame with #20 biscuits. The panels fit into the
inside face of this frame, within 1/4"-wide x 3/8"-deep table-routed rabbets you make after the
frames are dry and sanded flat.
The next step is to install the side panels, but two things must happen first. The edge of the
panels needs to be routed to fit the 3/8" rabbet you routed in the frame. The four rounded corners
of the frame rabbet must be squared with a sharp chisel. Secure the panel with 1/2" finishing nails
or wood trim on the inside face of the side frame. This is the same design and construction
process I used to build the face frame, door and drawer frames. Build these parts now. Sand
them flat, then rout a round-over profile on the outer edges of the drawer face and doors.
Bring the Cabinet Together
With the side and face frames done, it s time to join
them to the legs. I used screws driven into angled
pocket holes. This is fast, easy and allows me to
assemble the whole cabinet without waiting for glue to
dry.
When the cabinet is assembled, including the two
back support members, you can measure the opening
for your drawer box. Mechanical slides like the kind I
Creative cabriole legs Sillaot's trademark
used require a specific drawer-to-cabinet clearance
cut from a template drawer slides function
usually 1/2" on each side. That s why you should
refine the vanity's stance beautifully but require an
measure your drawer opening and make changes to
and give it a furniture- eye for precise
like appeal tolerances
the drawer specs if needed. Construction variations
can easily throw dimensions off 1/8" more than
enough to make mechanical drawer slides perform poorly. The plans show how the drawer
support rails provide a surface for the mechanical slides to fasten to.
I kept things simple with butt joints at all four drawer box corners. The drawer bottom fits into
1/4" x 1/4" dados in the sides, front and back. Install the drawer in its opening on the slides, then
temporarily fasten the frame and panel drawer face to the drawer box with four screws driven
from inside the box. Take the drawer face off for finishing.
Final Steps
Minwax pre-stain wood conditioner was used to even out the absorption of the Ipswich Pine stain.
The stain was sealed under three coats of oil-based urethane. Once the finish is complete, seat
the sink top on a bead of silicone applied along the top edges of the cabinet. Screws driven
through the top and bottom back members and into wall studs will secure it to the wall. Hook up
the plumbing and you re ready to go.
Copyright 2004 Martian Auctions 199
For the Cabinet Material Size Qty.
Front legs sugar pine 4" x 4" x 36" 2
Back legs sugar pine 2" x 2" x 36" 2
Side rails pine 3/4" x 2 1/4" x 9 3/4" 4
Side stiles pine 3/4" x 2 1/4" x 22 1/2" 4
Side panels pine 3/4" x 10 7/8" x 18 3/4" 2
Face frame stiles pine 3/4" x 2 1/4" x 22 1/2" 2
Face frame top rail pine 3/4" x 1 1/4" x 20 5/8" 1
Face frame centre rail pine 3/4" x 2" x 20 5/8" 1
Face frame bottom rail pine 3/4" x 1 1/2" x 20 5/8" 1
Drawer supports pine 3/4" x 2 3/4" x 16 1/8" 2
Top back cross member pine 3/4" x 4 1/2" x 25 1/4"
Bottom back cross member pine 3/4" x 2" x 25 1/4" 1
Sink top molded acrylic 19" x 31" 1
For the Doors
Door rails pine 3/4" x 1 3/4" x 7" 4
Door stiles pine 3/4" x 1 3/4" x 14 1/2" 4
Door panels redwood 3/4" x 7 5/8" x 11 5/8" 2
Door spacer pine 1/4" x 2" x 13 3/8" 1
For the Drawers
Drawer box fronts birch-veneer ply 1/2" x 4" x 18 5/8" 2
Drawer box sides birch-veneer ply 1/2" x 4" x 16" 2
Drawer bottoms birch-veneer ply 1/4" x 15 1/2" x 19 1/4" 1
Drawer face rails pine 3/4" x 1 3/4" x 18 1/4" 2
Drawer face stiles pine 3/4" x 1 3/4" x 5 1/2" 1
Drawer face panel redwood 3/4" x 2 5/8" x 19" 1
Drawer slides full-extension 16"-long 2
Drawer/door knobs white porcelain 1 1/8" dia. 4
Copyright 2004 Martian Auctions 200
Copyright 2004 Martian Auctions 201
Wyszukiwarka
Podobne podstrony:
cabinet bathroom 2cabinet bathroomCabinet Vanity unit bathroomCabinet spice cabinetCabinet entertainment center2The Cabinet Of Dr CaligariCabinet storage towerCabinet One door iceboxCabinet Entertainment Center BasicCabinet modern wardrobeCabinet linen closetCabinet country dry sinkCabinet marthas cupboardCabinet small desk cabinetwięcej podobnych podstron