Features
" Compatible with MCS"!-51 Products
" 12K Bytes of In-System Programmable (ISP) Flash Program Memory
 SPI Serial Interface for Program Downloading
 Endurance: 10,000 Write/Erase Cycles
" 2K Bytes EEPROM Data Memory
 Endurance: 100,000 Write/Erase Cycles
" 64-byte User Signature Array
" 2.7V to 5.5V Operating Range
8-bit
" Fully Static Operation: 0 Hz to 24 MHz
" Three-level Program Memory Lock
Microcontroller
" 256 x 8-bit Internal RAM
" 32 Programmable I/O Lines
with 12K Bytes
" Three 16-bit Timer/Counters
" Nine Interrupt Sources
Flash and 2K
" Enhanced UART Serial Port with Framing Error Detection and Automatic Address
Recognition
Bytes EEPROM
" Enhanced SPI (Double Write/Read Buffered) Serial Interface
" Low-power Idle and Power-down Modes
" Interrupt Recovery from Power-down Mode
AT89S8253
" Programmable Watchdog Timer
" Dual Data Pointer
" Power-off Flag
" Flexible ISP Programming (Byte and Page Modes)
Preliminary
 Page Mode: 64 Bytes/Page for Code Memory, 32 Bytes/Page for Data Memory
" Four-level Enhanced Interrupt Controller
" Programmable and Fuseable x2 Clock Option
" Internal Power-on Reset
" 42-pin PDIP Package Option for Reduced EMC Emission
" Green (Pb/Halide-free) Packaging Option
1. Description
The AT89S8253 is a low-power, high-performance CMOS 8-bit microcontroller with
12K bytes of In-System Programmable (ISP) Flash program memory and 2K bytes of
EEPROM data memory. The device is manufactured using Atmel s high-density non-
volatile memory technology and is compatible with the industry-standard MCS-51
instruction set and pinout. The on-chip downloadable Flash allows the program mem-
ory to be reprogrammed in-system through an SPI serial interface or by a
conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU
with downloadable Flash on a monolithic chip, the Atmel AT89S8253 is a powerful
microcontroller which provides a highly-flexible and cost-effective solution to many
embedded control applications.
3286C MICRO 1/05
The AT89S8253 provides the following standard features: 12K bytes of In-System Programma-
ble Flash, 2K bytes of EEPROM, 256 bytes of RAM, 32 I/O lines, programmable watchdog timer,
two data pointers, three 16-bit timer/counters, a six-vector, four-level interrupt architecture, a full
duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S8253 is designed
with static logic for operation down to zero frequency and supports two software selectable
power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters,
serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM
contents but freezes the oscillator, disabling all other chip functions until the next external inter-
rupt or hardware reset.
The on-board Flash/EEPROM is accessible through the SPI serial interface. Holding RESET
active forces the SPI bus into a serial programming interface and allows the program memory to
be written to or read from, unless one or more lock bits have been activated.
2. Pin Configurations
2.1 40P6  40-lead PDIP
(T2) P1.0 1 40 VCC
(T2 EX) P1.1 2 39 P0.0 (AD0)
P1.2 3 38 P0.1 (AD1)
P1.3 4 37 P0.2 (AD2)
(SS) P1.4 5 36 P0.3 (AD3)
(MOSI) P1.5 6 35 P0.4 (AD4)
(MISO) P1.6 7 34 P0.5 (AD5)
(SCK) P1.7 8 33 P0.6 (AD6)
RST 9 32 P0.7 (AD7)
(RXD) P3.0 10 31 EA/VPP
(TXD) P3.1 11 30 ALE/PROG
(INT0) P3.2 12 29 PSEN
(INT1) P3.3 13 28 P2.7 (A15)
(T0) P3.4 14 27 P2.6 (A14)
(T1) P3.5 15 26 P2.5 (A13)
(WR) P3.6 16 25 P2.4 (A12)
(RD) P3.7 17 24 P2.3 (A11)
XTAL2 18 23 P2.2 (A10)
XTAL1 19 22 P2.1 (A9)
GND 20 21 P2.0 (A8)
2.2 44A  44-lead TQFP
(MOSI) P1.5 1 33 P0.4 (AD4)
(MISO) P1.6 2 32 P0.5 (AD5)
(SCK) P1.7 3 31 P0.6 (AD6)
RST 4 30 P0.7 (AD7)
(RXD) P3.0 5 29 EA/VPP
NC 6 28 NC
(TXD) P3.1 7 27 ALE/PROG
(INT0) P3.2 8 26 PSEN
(INT1) P3.3 9 25 P2.7 (A15)
(T0) P3.4 10 24 P2.6 (A14)
(T1) P3.5 11 23 P2.5 (A13)
2
AT89S8253 [Preliminary]
3286C MICRO 1/05
44
P1.4 (SS)
43
P1.3
42
P1.2
41
P1.1 (T2 EX)
40
P1.0 (T2)
39
NC
38
VCC
37
P0.0 (AD0)
36
P0.1 (AD1)
35
P0.2 (AD2)
34
P0.3 (AD3)
GND
16
GND
17
XTAL2
14
XTAL1
15
(A8) P2.0
18
(A9) P2.1
19
(RD) P3.7
13
(WR) P3.6
12
(A10) P2.2
20
(A11) P2.3
21
(A12) P2.4
22
 AT89S8253 [Preliminary]
2.3 44J  44-lead PLCC
(MOSI) P1.5 7 P0.4 (AD4)
39
(MISO) P1.6 8 P0.5 (AD5)
38
9
(SCK) P1.7 P0.6 (AD6)
37
10
RST P0.7 (AD7)
36
11
(RXD) P3.0 35 EA/VPP
12
NC 34 NC
13
(TXD) P3.1 33 ALE/PROG
14
(INT0) P3.2 32 PSEN
15
(INT1) P3.3 31 P2.7 (A15)
16
(T0) P3.4 30 P2.6 (A14)
17
29
(T1) P3.5 P2.5 (A13)
2.4 42PS6  PDIP
RST 1 42 P1.7 (SCK)
(RXD) P3.0 2 41 P1.6 (MISO)
(TXD) P3.1 3 40 P1.5 (MOSI)
(INT0) P3.2 4 39 P1.4 (SS)
(INT1) P3.3 5 38 P1.3
(T0) P3.4 6 37 P1.2
(T1) P3.5 7 36 P1.1 (T2EX)
(WR) P3.6 8 35 P1.0 (T2)
(RD) P3.7 9 34 VDD
XTAL2 10 33 PWRVDD
XTAL1 11 32 P0.0 (AD0)
GND 12 31 P0.1 (AD1)
PWRGND 13 30 P0.2 (AD2)
(A8) P2.0 14 29 P0.3 (AD3)
(A9) P2.1 15 28 P0.4 (AD4)
(A10) P2.2 16 27 P0.5 (AD5)
(A11) P2.3 17 26 P0.6 (AD6)
(A12) P2.4 18 25 P0.7 (AD7)
(A13) P2.5 19 24 EA/VPP
(A14) P2.6 20 23 ALE/PROG
(A15) P2.7 21 22 PSEN
3. Pin Description
3.1 VCC
Supply voltage (all packages except 42-PDIP).
3.2 GND
Ground (all packages except 42-PDIP; for 42-PDIP GND connects only the logic core and the
embedded program/data memories).
3.3 VDD
Supply voltage for the 42-PDIP which connects only the logic core and the embedded pro-
gram/data memories.
3
3286C MICRO 1/05
NC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
6
P1.4 (SS)
5
P1.3
4
P1.2
3
P1.1 (T2 EX)
2
P1.0 (T2)
1
44
43
42
41
40
21
22
23
24
25
26
27
28
NC
GND
XTAL2
20
XTAL1
(A8) P2.0
(A9) P2.1
(RD) P3.7
19
(WR) P3.6
18
(A10) P2.2
(A11) P2.3
(A12) P2.4
3.4 PWRVDD
Supply voltage for the 42-PDIP which connects only the I/O Pad Drivers.
The application board must connect both VDD and PWRVDD to the board supply voltage.
3.5 PWRGND
Ground for the 42-PDIP which connects only the I/O Pad Drivers. PWRGND and GND are
weakly connected through the common silicon substrate, but not through any metal links. The
application board must connect both GND and PWRGND to the board ground.
3.6 Port 0
Port 0 is an 8-bit open drain bi-directional I/O port. As an output port, each pin can sink six TTL
inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs.
Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses
to external program and data memory. In this mode, P0 has internal pull-ups.
Port 0 also receives the code bytes during Flash programming and outputs the code bytes dur-
ing program verification. External pull-ups are required during program verification.
3.7 Port 1
Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can
sink/source six TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the weak
internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being
pulled low will source current (IIL,150 µA typical) because of the weak internal pull-ups.
Some Port 1 pins provide additional functions. P1.0 and P1.1 can be configured to be the
timer/counter 2 external count input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX),
respectively.
Furthermore, P1.4, P1.5, P1.6, and P1.7 can be configured as the SPI slave port select, data
input/output and shift clock input/output pins as shown in the following table.
Port Pin Alternate Functions
P1.0 T2 (external count input to Timer/Counter 2), clock-out
P1.1 T2EX (Timer/Counter 2 capture/reload trigger and direction control)
P1.4 SS (Slave port select input)
P1.5 MOSI (Master data output, slave data input pin for SPI channel)
P1.6 MISO (Master data input, slave data output pin for SPI channel)
P1.7 SCK (Master clock output, slave clock input pin for SPI channel)
Port 1 also receives the low-order address bytes during Flash programming and verification.
4
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
3.8 Port 2
Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 2 output buffers can
sink/source six TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the weak
internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being
pulled low will source current (IIL,150 µA typical) because of the weak internal pull-ups.
Port 2 emits the high-order address byte during fetches from external program memory and dur-
ing accesses to external data memory that use 16-bit addresses (MOVX @ DPTR). In this
application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external
data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2
Special Function Register.
Port 2 also receives the high-order address bits and some control signals during Flash
programming and verification.
3.9 Port 3
Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 3 output buffers can
sink/source six TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the weak
internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being
pulled low will source current (IIL,150 µA typical) because of the weak internal pull-ups.
Port 3 receives some control signals for Flash programming and verification.
Port 3 also serves the functions of various special features of the AT89S8253, as shown in the
following table.
Port Pin Alternate Functions
P3.0 RXD (serial input port)
P3.1 TXD (serial output port)
P3.2 INT0 (external interrupt 0)(1)
P3.3 INT1 (external interrupt 1)(1)
P3.4 T0 (timer 0 external input)
P3.5 T1 (timer 1 external input)
P3.6 WR (external data memory write strobe)
P3.7 RD (external data memory read strobe)
Note: 1. All pins in ports 1 and 2 and almost all pins in port 3 (the exceptions are P3.2 INT0 and P3.3
INT1) have their weak internal pull-ups disabled in the Power-down mode. Port pins P3.2
(INT0) and P3.1 (INT1) are active even in Power-down mode (to be able to sense an
interrupt request to exit the Power-down mode) and as such still have their weak internal pull-
ups turned on.
5
3286C MICRO 1/05
3.10 RST
Reset input. A high on this pin for at least two machine cycles while the oscillator is running
resets the device.
3.11 ALE/PROG
Address Latch Enable. ALE/PROG is an output pulse for latching the low byte of the address
(on its falling edge) during accesses to external memory. This pin is also the program pulse input
(PROG) during Flash programming.
In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be
used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped dur-
ing each access to external data memory.
If desired, ALE operation can be disabled by setting bit 0 of the AUXR SFR at location 8EH. With
the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly
pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execu-
tion mode.
3.12 PSEN
Program Store Enable. PSEN is the read strobe to external program memory (active low).
When the AT89S8253 is executing code from external program memory, PSEN is activated
twice each machine cycle, except that two PSEN activations are skipped during each access to
external data memory.
3.13 EA/VPP
External Access Enable. EA must be strapped to GND in order to enable the device to fetch
code from external program memory locations starting at 0000H up to FFFFH. Note, however,
that if lock bit 1 is programmed, EA will be internally latched on reset.
EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt
programming enable voltage (VPP) during Flash programming when 12-volt programming is
selected.
3.14 XTAL1
Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
3.15 XTAL2
Output from the inverting oscillator amplifier.
6
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
4. Block Diagram
P0.0 - P0.7 P2.0 - P2.7
VCC
PORT 0 DRIVERS PORT 2 DRIVERS
GND
RAM ADDR. PORT 0
PORT 2
RAM
EEPROM FLASH
REGISTER LATCH
LATCH
PROGRAM
B STACK
ADDRESS
ACC
REGISTER POINTER
REGISTER
BUFFER
TMP2 TMP1
PC
INCREMENTER
ALU
INTERRUPT, SERIAL PORT,
AND TIMER BLOCKS
PROGRAM
COUNTER
PSW
PSEN
TIMING
ALE/PROG
INSTRUCTION DUAL
AND
REGISTER
DPTR
EA / VPP CONTROL
RST
WATCH PORT 3
PORT 1 SPI
PROGRAM
DOG LATCH
LATCH PORT
LOGIC
OSC
PORT 3 DRIVERS
PORT 1 DRIVERS
P3.0 - P3.7
P1.0 - P1.7
7
3286C MICRO 1/05
5. Special Function Registers
A map of the on-chip memory area called the Special Function Register (SFR) space is shown in
Table 5-1.
Note that not all of the addresses are occupied, and unoccupied addresses may not be imple-
mented on the chip. Read accesses to these addresses will generally return random data, and
write accesses will have an indeterminate effect.
User software should not write 1s to these unlisted locations, since they may be used in future
products to invoke new features. In that case, the reset or inactive values of the new bits will
always be 0.
Table 5-1. AT89S8253 SFR Map and Reset Values
0F8H 0FFH
B
0F0H 0F7H
00000000
0E8H 0EFH
ACC
0E0H 0E7H
00000000
0D8H 0DFH
PSW SPCR
0D0H 0D7H
00000000 00000100
T2CON T2MOD RCAP2L RCAP2H TL2 TH2
0C8H 0CFH
00000000 XXXXXX00 00000000 00000000 00000000 00000000
0C0H 0C7H
SADEN
IP
0B8H 0BFH
XX000000
00000000
IPH
P3
0B0H 0B7H
11111111
XX000000
SADDR
IE SPSR
0A8H 0AFH
0X000000 000XXX00
00000000
WDTCON
P2 WDTRST
0A0H 0A7H
11111111 (Write Only)
0000 0000
SCON SBUF
98H 9FH
00000000 XXXXXXXX
P1 EECON
90H 97H
11111111 XX000011
AUXR CLKREG
TCON TMOD TL0 TL1 TH0 TH1
88H 8FH
00000000 00000000 00000000 00000000 00000000 00000000
XXXXXXX0 XXXXXXX0
P0 SP DP0L DP0H DP1L DP1H SPDR PCON
80H 87H
11111111 00000111 00000000 00000000 00000000 00000000 ######## 0XXX0000
Note: # means: 0 after cold reset and unchanged after warm reset.
8
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
5.1 Auxiliary Register
The AUXR Register contains a single active bit called DISALE.
Table 5-2. AUXR  Auxiliary Register
AUXR Address = 8EH Reset Value = XXXX XXX0B
Not Bit Addressable
      Intel_Pwd_Exit DISALE
Bit 765432 1 0
Symbol Function
When DISALE = 0, ALE is emitted at a constant rate of 1/6 the oscillator frequency (except during MOVX when 1
DISALE
ALE pulse is missing). When DISALE = 1, ALE is active only during a MOVX or MOVC instruction.
When set, this bit configures the interrupt driven exit from power-down to resume execution on the rising edge of
Intel_Pwd_Exit the interrupt signal. When this bit is cleared, the execution resumes after a self-timed interval (nominal 2 ms)
referenced from the falling edge of the interrupt signal.
5.2 Clock Register
The CLKREG register contains a single active bit called X2.
Table 5-3. CLKREG  Clock Register
CLKREG Address = 8FH Reset Value = XXXX XXX0B
Not Bit Addressable
       X2
Bit 76543210
Symbol Function
When X2 = 0, the oscillator frequency (at XTAL1 pin) is internally divided by 2 before it is used as the device system
frequency.
X2
When X2 = 1, the divider by 2 is no longer used and the XTAL1 frequency becomes the device system frequency. This
enables the user to choose a 6 MHz crystal instead of a 12 MHz crystal, for example, in order to reduce EMI.
9
3286C MICRO 1/05
5.3 SPI Registers
Control and status bits for the Serial Peripheral Interface are contained in registers SPCR (see
Table 15-1 on page 26) and SPSR (see Table 15-2 on page 27). The SPI data bits are contained
in the SPDR register. In normal SPI mode, writing the SPI data register during serial data trans-
fer sets the Write Collision bit (WCOL) in the SPSR register. In enhanced SPI mode, the SPDR
is also write double-buffered because WCOL works as a Write Buffer Full Flag instead of being a
collision flag. The values in SPDR are not changed by Reset.
5.4 Interrupt Registers
The global interrupt enable bit and the individual interrupt enable bits are in the IE register. In
addition, the individual interrupt enable bit for the SPI is in the SPCR register. Four priorities can
be set for each of the six interrupt sources in the IP and IPH registers.
IPH bits have the same functions as IP bits, except IPH has higher priority than IP. By using IPH
in conjunction with IP, a priority level of 0, 1, 2, or 3 may be set for each interrupt.
5.5 Dual Data Pointer Registers
To facilitate accessing both internal EEPROM and external data memory, two banks of 16-bit
Data Pointer Registers are provided: DP0 at SFR address locations 82H - 83H and DP1 at 84H
- 85H. Bit DPS = 0 in SFR WMCON selects DP0 and DPS = 1 selects DP1. The user should
ALWAYS initialize the DPS bit to the appropriate value before accessing the respective Data
Pointer Register.
5.6 Power Off Flag
The Power Off Flag (POF), located at bit_4 (PCON.4) in the PCON SFR. POF, is set to  1 dur-
ing power up. It can be set and reset under software control and is not affected by RESET.
6. Data Memory  EEPROM and RAM
The AT89S8253 implements 2K bytes of on-chip EEPROM for data storage and 256 bytes of
RAM. The upper 128 bytes of RAM occupy a parallel space to the Special Function Registers.
That means the upper 128 bytes have the same addresses as the SFR space but are physically
separate from SFR space.
When an instruction accesses an internal location above address 7FH, the address mode used
in the instruction specifies whether the CPU accesses the upper 128 bytes of RAM or the SFR
space. Instructions that use direct addressing access the SFR space.
For example, the following direct addressing instruction accesses the SFR at location 0A0H
(which is P2).
MOV 0A0H, #data
Instructions that use indirect addressing access the upper 128 bytes of RAM. For example, the
following indirect addressing instruction, where R0 contains 0A0H, accesses the data byte at
address 0A0H, rather than P2 (whose address is 0A0H).
MOV @R0, #data
Note that stack operations are examples of indirect addressing, so the upper 128 bytes of data
RAM are available as stack space.
The on-chip EEPROM data memory is selected by setting the EEMEN bit in the EECON register
at SFR address location 96H. The EEPROM address range is from 000H to 7FFH. MOVX
10
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
instructions are used to access the EEPROM. To access off-chip data memory with the MOVX
instructions, the EEMEN bit needs to be set to  0 .
The EEMWE bit in the EECON register needs to be set to  1 before any byte location in the
EEPROM can be written. User software should reset EEMWE bit to  0 if no further EEPROM
write is required. EEPROM write cycles in the serial programming mode are self-timed and typi-
cally take 4 ms. The progress of EEPROM write can be monitored by reading the RDY/BSY bit
(read-only) in SFR EECON. RDY/BSY = 0 means programming is still in progress and RDY/BSY
= 1 means an EEPROM write cycle is completed and another write cycle can be initiated. Bit
EELD in EECON controls whether the next MOVX instruction will only load the write buffer of the
EEPROM or will actually start the programming cycle. By setting EELD, only load will occur.
Before the last MOVX in a given page of 32 bytes, EELD should be cleared so that after the last
MOVX the entire page will be programmed at the same time. This way, 32 bytes will only require
4 ms of programming time instead of 128 ms required in single byte programming.
In addition, during EEPROM programming, an attempted read from the EEPROM will fetch the
byte being written with the MSB complemented. Once the write cycle is completed, true data are
valid at all bit locations.
7. Memory Control Register
The EECON register contains control bits for the 2K bytes of on-chip data EEPROM. It also con-
tains the control bit for the dual data pointer.
Table 7-1. EECON  Data EEPROM Control Register
EECON Address = 96H Reset Value = XX00 0011B
Not Bit Addressable
Bit   EELD EEMWE EEMEN DPS RDY/BSY WRTINH
765432 1 0
Symbol Function
EEPROM data memory load enable bit. Used to implement Page Mode Write. A MOVX instruction writing into the data
EEPROM will not initiate the programming cycle if this bit is set, rather it will just load data into the volatile data buffer of
EELD
the data EEPROM memory. Before the last MOVX, reset this bit and the data EEPROM will program all the bytes
previously loaded on the same page of the address given by the last MOVX instruction.
EEPROM data memory write enable bit. Set this bit to 1 before initiating byte write to on-chip EEPROM with the MOVX
EEMWE
instruction. User software should set this bit to 0 after EEPROM write is completed.
Internal EEPROM access enable. When EEMEN = 1, the MOVX instruction with DPTR will access on-chip EEPROM
EEMEN instead of external data memory if the address used is less than 2K. When EEMEN = 0 or the address used is e" 2K,
MOVX with DPTR accesses external data memory.
Data pointer register select. DPS = 0 selects the first bank of data pointer register, DP0, and DPS = 1 selects the
DPS
second bank, DP1.
RDY/BSY (Ready/Busy) flag for the data EEPROM memory. This is a read-only bit which is cleared by hardware during
the programming cycle of the on-chip EEPROM. It is also set by hardware when the programming is completed. Note
RDY/BSY
that RDY/BSY will be cleared long after the completion of the MOVX instruction which has initiated the programming
cycle.
WRTINH (Write Inhibit) is a READ-ONLY bit which is cleared by hardware when Vcc is too low for the programming cycle
WRTINH of the on-chip EEPROM to be executed. When this bit is cleared, an ongoing programming cycle will be aborted or a
new programming cycle will not start.
11
3286C MICRO 1/05
8. Programmable Watchdog Timer
The programmable Watchdog Timer (WDT) counts instruction cycles. The prescaler bits, PS0,
PS1 and PS2 in SFR WDTCON are used to set the period of the Watchdog Timer from 16K to
2048K instruction cycles. The available timer periods are shown in Table 8-1. The WDT time-out
period is dependent upon the external clock frequency.
The WDT is disabled by Power-on Reset and during Power-down mode. When WDT times out
without being serviced or disabled, an internal RST pulse is generated to reset the CPU. See
Table 8-1 for the WDT period selections.
Table 8-1. Watchdog Timer Time-out Period Selection
WDT Prescaler Bits
Period (Nominal for
PS2 PS1 PS0 FCLK = 12 MHz)
00 0 16 ms
00 1 32 ms
01 0 64 ms
01 1 128 ms
10 0 256 ms
10 1 512 ms
1 1 0 1024 ms
1 1 1 2048 ms
12
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
8.1 Watchdog Control Register
The WDTCON register contains control bits for the Watchdog Timer (shown in Table 8-2).
Table 8-2. WDTCON  Watchdog Control Register
WDTCON Address = A7H Reset Value = 0000 0000B
Not Bit Addressable
PS2 PS1 PS0 WDIDLE DISRTO HWDT WSWRST WDTEN
Bit 76543210
Symbol Function
PS2 Prescaler bits for the watchdog timer (WDT). When all three bits are cleared to 0, the watchdog timer has a nominal
PS1 period of 16K machine cycles, (i.e. 16 ms at a XTAL frequency of 24 MHz in normal mode). When all three bits are set
PS0 to 1, the nominal period is 2048K machine cycles, (i.e. 2048 ms at 24 MHz clock frequency).
Disable/enable the Watchdog Timer in IDLE mode. When WDIDLE = 0, WDT continues to count in IDLE mode. When
WDIDLE
WDIDLE = 1, WDT freezes while the device is in IDLE mode.
Disable/enable the WDT-driven Reset Out (WDT drives the RST pin). When DISRTO = 0, the RST pin is driven high
DISRTO after WDT times out and the entire board is reset. When DISRTO = 1, the RST pin remains only as an input and the
WDT resets only the microcontroller internally after WDT times out.
Hardware mode select for the WDT. When HWDT = 0, the WDT can be turned on/off by simply setting or clearing
WDTEN in the same register (this is the software mode for WDT). When HWDT = 1, the WDT has to be set by writing
the sequence 1EH/E1H to the WDTRST register (with address 0A6H) and after being set in this way, WDT cannot be
HWDT
turned off except by reset, warm or cold (this is the hardware mode for WDT). To prevent the hardware WDT from
resetting the entire device, the same sequence 1EH/E1H must be written to the same WDTRST SFR before the
timeout interval.
Watchdog software reset bit. When HWDT = 0 (i.e. WDT is in software controlled mode), this bit resets WDT. After being
WSWRST set by software, WSWRST is reset by hardware during the next machine cycle. If HWDT = 1, this bit has no effect, and if
set by software, it will not be cleared by hardware.
Watchdog software enable bit. When HWDT = 0 (i.e. WDT is in software-controlled mode), this bit enables WDT when
WDTEN set to 1 and disables WDT when cleared to 0 (it does not reset WDT in this case, but just freezes the existing counter
state). If HWDT = 1, this bit is READ-ONLY and reflects the status of the WDT (whether it is running or not).
13
3286C MICRO 1/05
9. Timer 0 and 1
Timer 0 and Timer 1 in the AT89S8253 operate the same way as Timer 0 and Timer 1 in the
AT89S51 and AT89S52. For more detailed information on the Timers operation, refer to the
Atmel Web site (www.atmel.com). From the home page, select  Products, then  Microcontrol-
lers , then  8051-Architecture , then  Documentation , and  Other Documents . Open the Adobe
Acrobat file  AT89 Series Hardware Description.
10. Timer 2
Timer 2 is a 16-bit Timer/Counter that can operate as either a timer or an event counter. The
type of operation is selected by bit C/T2 in the SFR T2CON (see Table 10-2 on page 15). Timer
2 has three operating modes: capture, auto-reload (up or down counting), and baud rate gener-
ator. The modes are selected by bits in T2CON, as shown in Table 10-2.
Timer 2 consists of two 8-bit registers, TH2 and TL2. In the Timer function, the TL2 register is
incremented every machine cycle. Since a machine cycle consists of 12 oscillator periods, the
count rate is 1/12 of the oscillator frequency.
In the Counter function, the register is incremented in response to a 1-to-0 transition at its corre-
sponding external input pin, T2. In this function, the external input is sampled during S5P2 of
every machine cycle. When the samples show a high in one cycle and a low in the next cycle,
the count is incremented. The new count value appears in the register during S3P1 of the cycle
following the one in which the transition was detected. Since two machine cycles (24 oscillator
periods) are required to recognize a 1-to-0 transition, the maximum count rate is 1/24 of the
oscillator frequency. To ensure that a given level is sampled at least once before it changes, the
level should be held for at least one full machine cycle.
Table 10-1. Timer 2 Operating Modes
RCLK + TCLK CP/RL2 TR2 MODE
0 0 1 16-bit Auto-reload
0 1 1 16-bit Capture
1 X 1 Baud Rate Generator
X X 0 (Off)
14
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Table 10-2. T2CON  Timer/Counter 2 Control Register
T2CON Address = 0C8H Reset Value = 0000 0000B
Bit Addressable
TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2
Bit 76543210
Symbol Function
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either
TF2
RCLK = 1 or TCLK = 1.
Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
EXF2 When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be
cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).
Receive clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in serial port
RCLK
Modes 1 and 3. RCLK = 0 causes Timer 1 overflows to be used for the receive clock.
Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial port
TCLK
Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if
EXEN2
Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.
TR2 Start/Stop control for Timer 2. TR2 = 1 starts the timer.
Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge
C/T2
triggered).
Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative transitions at T2EX if EXEN2 = 1. CP/RL2 = 0
CP/RL2 causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1. When
either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.
15
3286C MICRO 1/05
10.1 Timer 2 Registers
Control and status bits are contained in registers T2CON (see Table 10-2) and T2MOD (see
Table 10-3) for Timer 2. The register pair (RCAP2H, RCAP2L) are the Capture/Reload registers
for Timer 2 in 16-bit capture mode or 16-bit auto-reload mode.
10.2 Capture Mode
In the capture mode, two options are selected by bit EXEN2 in T2CON. If EXEN2 = 0, Timer 2 is
a 16-bit timer or counter which upon overflow sets bit TF2 in T2CON. This bit can then be used
to generate an interrupt. If EXEN2 = 1, Timer 2 performs the same operation, but a 1-to-0 transi-
tion at external input T2EX also causes the current value in TH2 and TL2 to be captured into
RCAP2H and RCAP2L, respectively. In addition, the transition at T2EX causes bit EXF2 in
T2CON to be set. The EXF2 bit, like TF2, can generate an interrupt. The capture mode is illus-
trated in Figure 10-1.
Figure 10-1. Timer 2 in Capture Mode
÷12
OSC
C/T2 = 0
TH2 TL2 TF2
OVERFLOW
CONTROL
TR2
C/T2 = 1
CAPTURE
T2 PIN
RCAP2H RCAP2L
TRANSITION
TIMER 2
DETECTOR
INTERRUPT
T2EX PIN EXF2
CONTROL
EXEN2
16
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
10.3 Auto-reload (Up or Down Counter)
Timer 2 can be programmed to count up or down when configured in its 16-bit auto-reload
mode. This feature is invoked by the DCEN (Down Counter Enable) bit located in the SFR
T2MOD (see Table 10-3). Upon reset, the DCEN bit is set to 0 so that timer 2 will default to
count up. When DCEN is set, Timer 2 can count up or down, depending on the value of the
T2EX pin.
Table 10-3. T2MOD  Timer 2 Mode Control Register
T2MOD Address = 0C9H Reset Value = XXXX XX00B
Not Bit Addressable
      T2OE DCEN
Bit 76543210
Symbol Function
 Not implemented, reserved for future use.
T2OE Timer 2 Output Enable bit.
DCEN When set, this bit allows Timer 2 to be configured as an up/down counter.
Figure 10-2 shows Timer 2 automatically counting up when DCEN = 0. In this mode, two options
are selected by bit EXEN2 in T2CON. If EXEN2 = 0, Timer 2 counts up to 0FFFFH and then sets
the TF2 bit upon overflow. The overflow also causes the timer registers to be reloaded with the
16-bit value in RCAP2H and RCAP2L. The values in RCAP2H and RCAP2L are preset by soft-
ware. If EXEN2 = 1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0
transition at external input T2EX. This transition also sets the EXF2 bit. Both the TF2 and EXF2
bits can generate an interrupt if enabled.
Setting the DCEN bit enables Timer 2 to count up or down, as shown in Figure 10-3. In this
mode, the T2EX pin controls the direction of the count. A logic 1 at T2EX makes Timer 2 count
up. The timer will overflow at 0FFFFH and set the TF2 bit. This overflow also causes the 16-bit
value in RCAP2H and RCAP2L to be reloaded into the timer registers, TH2 and TL2,
respectively.
A logic 0 at T2EX makes Timer 2 count down. The timer underflows when TH2 and TL2 equal
the values stored in RCAP2H and RCAP2L. The underflow sets the TF2 bit and causes 0FFFFH
to be reloaded into the timer registers.
The EXF2 bit toggles whenever Timer 2 overflows or underflows and can be used as a 17th bit
of resolution. In this operating mode, EXF2 does not flag an interrupt.
17
3286C MICRO 1/05
Figure 10-2. Timer 2 in Auto Reload Mode (DCEN = 0)
Figure 10-3. Timer 2 Auto Reload Mode (DCEN = 1 Timer 2 Auto Reload Mode (DCEN = 1)
18
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Figure 10-4. Timer 2 in Baud Rate Generator Mode
TIMER 1 OVERFLOW
÷2
"0" "1"
NOTE: OSC. FREQ. IS DIVIDED BY 2, NOT 12
SMOD1
OSC
÷2
C/T2 = 0
"1" "0"
TH2 TL2
RCLK
Rx
CLOCK
CONTROL
÷16
TR2
C/T2 = 1
"1" "0"
T2 PIN
TCLK
RCAP2H RCAP2L Tx
CLOCK
TRANSITION
÷16
DETECTOR
TIMER 2
T2EX PIN
EXF2
INTERRUPT
CONTROL
EXEN2
11. Baud Rate Generator
Timer 2 is selected as the baud rate generator by setting TCLK and/or RCLK in T2CON (Table
10-2). Note that the baud rates for transmit and receive can be different if Timer 2 is used for the
receiver or transmitter and Timer 1 is used for the other function. Setting RCLK and/or TCLK
puts Timer 2 into its baud rate generator mode, as shown in Figure 10-4.
The baud rate generator mode is similar to the auto-reload mode, in that a rollover in TH2
causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and
RCAP2L, which are preset by software.
The baud rates in Modes 1 and 3 are determined by Timer 2 s overflow rate according to the fol-
lowing equation.
Timer 2 Overflow Rate
Modes 1 and 3 Baud Rates = -----------------------------------------------------------
-
16
The Timer can be configured for either timer or counter operation. In most applications, it is con-
figured for timer operation (CP/T2 = 0). The timer operation is different for Timer 2 when it is
used as a baud rate generator. Normally, as a timer, it increments every machine cycle (at 1/12
the oscillator frequency). As a baud rate generator, however, it increments every state time (at
1/2 the oscillator frequency). The baud rate formula is given below.
Modes 1 and 3 Oscillator Frequency
--------------------------------------- = ----------------------------------------------------------------------------------------------
Baud Rate 32 × [65536  (RCAP2H,RCAP2L)]
19
3286C MICRO 1/05
where (RCAP2H, RCAP2L) is the content of RCAP2H and RCAP2L taken as a 16-bit unsigned
integer.
Timer 2 as a baud rate generator is shown in Figure 10-4. This figure is valid only if RCLK or
TCLK = 1 in T2CON. Note that a rollover in TH2 does not set TF2 and will not generate an inter-
rupt. Note too, that if EXEN2 is set, a 1-to-0 transition in T2EX will set EXF2 but will not cause a
reload from (RCAP2H, RCAP2L) to (TH2, TL2). Thus when Timer 2 is in use as a baud rate gen-
erator, T2EX can be used as an extra external interrupt.
Note that when Timer 2 is running (TR2 = 1) as a timer in the baud rate generator mode, TH2 or
TL2 should not be read from or written to. Under these conditions, the Timer is incremented
every state time, and the results of a read or write may not be accurate. The RCAP2 registers
may be read but should not be written to, because a write might overlap a reload and cause
write and/or reload errors. The timer should be turned off (clear TR2) before accessing the Timer
2 or RCAP2 registers.
12. Programmable Clock Out
A 50% duty cycle clock can be programmed to come out on P1.0, as shown in Figure 12-1. This
pin, besides being a regular I/O pin, has two alternate functions. It can be programmed to input
the external clock for Timer/Counter 2 or to output a 50% duty cycle clock ranging from 61 Hz to
4 MHz (for a 16 MHz operating frequency).
To configure the Timer/Counter 2 as a clock generator, bit C/T2 (T2CON.1) must be cleared and
bit T2OE (T2MOD.1) must be set. Bit TR2 (T2CON.2) starts and stops the timer.
The clock-out frequency depends on the oscillator frequency and the reload value of Timer 2
capture registers (RCAP2H, RCAP2L), as shown in the following equation.
Oscillator Frequency
Clock Out Frequency = -------------------------------------------------------------------------------------------
4 × [65536  (RCAP2H,RCAP2L)]
In the clock-out mode, Timer 2 rollovers will not generate an interrupt. This behavior is similar to
when Timer 2 is used as a baud-rate generator. It is possible to use Timer 2 as a baud-rate gen-
erator and a clock generator simultaneously. Note, however, that the baud-rate and clock-out
frequencies cannot be determined independently from one another since they both use
RCAP2H and RCAP2L.
20
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Figure 12-1. Timer 2 in Clock-out Mode
13. UART
The UART in the AT89S8253 operates the same way as the UART in the AT89S51 and
AT89S52. For more detailed information on the UART operation refer to the Atmel Web site
(www.atmel.com). From the home page, select  Products, then  Microcontrollers , then  8051-
Architecture, then  Documentation , and  Other Documents . Open the Adobe Acrobat file
 AT89 Series Hardware Description.
13.1 Enhanced UART
In addition to all of its usual modes, the UART can perform framing error detection by looking for
missing stop bits, and automatic address recognition. The UART also fully supports multiproces-
sor communication as does the standard 80C51 UART.
When used for framing error detect, the UART looks for missing stop bits in the communication.
A missing bit will set the FE bit in the SCON register. The FE bit shares the SCON.7 bit with SM0
and the function of SCON.7 is determined by PCON.6 (SMOD0). If SMOD0 is set then SCON.7
functions as FE. SCON.7 functions as SM0 when SMOD0 is cleared. When used as FE,
SCON.7 can only be cleared by software.
13.1.1 Automatic Address Recognition
Automatic Address Recognition is a feature which allows the UART to recognize certain
addresses in the serial bit stream by using hardware to make the comparisons. This feature
saves a great deal of software overhead by eliminating the need for the software to examine
every serial address which passes by the serial port. This feature is enabled by setting the SM2
bit in SCON. In the 9-bit UART modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will
be automatically set when the received byte contains either the  Given address or the  Broad-
21
3286C MICRO 1/05
cast address. The 9-bit mode requires that the 9th information bit is a 1 to indicate that the
received information is an address and not data.
The 8-bit mode is called mode 1. In this mode the RI flag will be set if SM2 is enabled and the
information received has a valid stop bit following the 8 address bits and the information is either
a Given or Broadcast address.
Mode 0 is the Shift Register mode and SM2 is ignored.
Using the Automatic Address Recognition feature allows a master to selectively communicate
with one or more slaves by invoking the given slave address or addresses. All of the slaves may
be contacted by using the Broadcast address. Two special Function Registers are used to
define the slave s address, SADDR, and the address mask, SADEN. SADEN is used to define
which bits in the SADDR are to be used and which bits are  don t care . The SADEN mask can
be logically ANDed with the SADDR to create the  Given address which the master will use for
addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized
while excluding others. The following examples will help to show the versatility of this scheme:
Slave 0 SADDR = 1100 0000
SADEN = 1111 1101
Given = 1100 00X0
Slave 1 SADDR = 1100 0000
SADEN = 1111 1110
Given = 1100 000X
In the previous example SADDR is the same and the SADEN data is used to differentiate
between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in
bit 1 and bit 0 is ignored. A unique address for slave 0 would be 1100 0010 since slave 1
requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will
exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0
(for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000.
In a more complex system the following could be used to select slaves 1 and 2 while excluding
slave 0:
Slave 0 SADDR = 1100 0000
SADEN = 1111 1001
Given = 1100 0XX0
Slave 1 SADDR = 1110 0000
SADEN = 1111 1010
Given = 1110 0X0X
Slave 2 SADDR = 1110 0000
SADEN = 1111 1100
Given = 1110 00XX
22
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
In the previous example the differentiation among the 3 slaves is in the lower 3 address bits.
Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires
that bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0
and its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2, use
address 1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2.
The Broadcast Address for each slave is created by taking the logical OR of SADDR and
SADEN. Zeros in this result are trended as don t-cares. In most cases, interpreting the don t-
cares as ones, the broadcast address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are loaded with 0s.
This produces a given address of all  don t cares as well as a Broadcast address of all  don t
cares . This effectively disables the Automatic Addressing mode and allows the microcontroller
to use standard 80C51-type UART drivers which do not make use of this feature.
Table 13-1. SCON  Serial Port Control Register
SCON Address = 98H Reset Value = 0000 0000B
Bit Addressable
SM0/FE SM1 SM2 REN TB8 RB8 T1 RI
Bit 7 6543210
(SMOD = 0/1)(1)
Symbol Function
Framing error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
FE frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit. FE will be set
regardless of the state of SMOD.
SM0 Serial Port Mode Bit 0, (SMOD must = 0 to access bit SM0)
Serial Port Mode Bit 1
SM0 SM1 Mode Description Baud Rate(2)
0 0 0 shift register fosc/12
SM1
0 1 1 8-bit UART variable
102 9-bit UART fosc/64 or fosc/32
1 1 3 9-bit UART variable
Enables the Automatic Address Recognition feature in modes 2 or 3. If SM2 = 1 then Rl will not be set unless the received
9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address. In mode 1, if SM2 =
SM2
1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a Given or Broadcast Address.
In Mode 0, SM2 should be 0.
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
REN
The 9th data bit that will be transmitted in modes 2 and 3. Set or clear by software as desired.
TB8
In modes 2 and 3, the 9th data bit that was received. In mode 1, if SM2 = 0, RB8 is the stop bit that was
RB8
received. In mode 0, RB8 is not used.
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or at the beginning of the
TI
stop bit in the other modes, in any serial transmission. Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or halfway through the stop
RI
bit time in the other modes, in any serial reception (except see SM2). Must be cleared by software.
Notes: 1. SMOD is located at PCON.7.
2. fosc = oscillator frequency.
23
3286C MICRO 1/05
15. Serial Peripheral Interface
The serial peripheral interface (SPI) allows high-speed synchronous data transfer between the
AT89S8253 and peripheral devices or between multiple AT89S8253 devices. The AT89S8253
SPI features include the following:
" Full-Duplex, 3-Wire Synchronous Data Transfer
" Master or Slave Operation
" Maximum Bit Frequency = f/4 (f/2 if in x2 Clock Mode)
" LSB First or MSB First Data Transfer
" Four Programmable Bit Rates in Master Mode
" End of Transmission Interrupt Flag
" Write Collision Flag Protection
" Double-Buffered Receive
" Double-Buffered Transmit (Enhanced Mode only)
" Wakeup from Idle Mode (Slave Mode only)
The interconnection between master and slave CPUs with SPI is shown in Figure 15-1. The four
pins in the interface are Master-In/Slave-Out (MISO), Master-Out/Slave-In (MOSI), Shift Clock
(SCK), and Slave Select (SS). The SCK pin is the clock output in master mode, but is the clock
input in slave mode. The MSTR bit in SPCR determines the directions of MISO and MOSI. Also
notice that MOSI connects to MOSI and MISO to MISO. In master mode, SS/P1.4 is ignored and
may be used as a general-purpose input or output. In slave mode, SS must be driven low to
select an individual device as a slave. When SS is driven high, the slave s SPI port is deacti-
vated and the MOSI/P1.5 pin can be used as a general-purpose input.
Figure 15-1. SPI Master-Slave Interconnection
MSB MASTER LSB
MSB SLAVE LSB
MISO MISO
8-BIT SHIFT REGISTER 8-BIT SHIFT REGISTER
MOSI MOSI
SCK SCK
SPI
CLOCK GENERATOR
SS SS
VCC
24
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Figure 15-2. SPI Block Diagram
S
MISO
P1.6
M
OSCILLATOR
MOSI
M
P1.5
MSB LSB
S
8/16-BIT SHIFT REGISTER
READ DATA BUFFER
DIVIDER
WRITE DATA BUFFER
÷4÷16÷64÷128
CLOCK
SPI CLOCK (MASTER)
SCK
CLOCK S
SELECT 1.7
LOGIC
M
SS
P1.4
MSTR
SPE
SPI CONTROL
8
SPI STATUS REGISTER SPI CONTROL REGISTER
8 8
SPI INTERRUPT INTERNAL
REQUEST DATA BUS
The SPI has two modes of operation: normal (non-buffered write) and enhanced (buffered
write). In normal mode, writing to the SPI data register (SPDR) of the master CPU starts the SPI
clock generator and the data written shifts out of the MOSI pin and into the MOSI pin of the slave
CPU. Transmission may start after an initial delay while the clock generator waits for the next full
bit slot of the specified baud rate. After shifting one byte, the SPI clock generator stops, setting
the end of transmission flag (SPIF) and transferring the received byte to the read buffer (SPDR).
If both the SPI interrupt enable bit (SPIE) and the serial port interrupt enable bit (ES) are set, an
interrupt is requested. Note that SPDR refers to either the write data buffer or the read data
buffer, depending on whether the access is a write or read. In normal mode, because the write
buffer is transparent (and a write access to SPDR will be directed to the shift buffer), any attempt
to write to SPDR while a transmission is in progress will result in a write collision with WCOL set.
However, the transmission will still complete normally, but the new byte will be ignored and a
new write access to SPDR will be necessary.
Enhanced mode is similar to normal mode except that the write buffer holds the next byte to be
transmitted. Writing to SPDR loads the write buffer and sets WCOL to signify that the buffer is
full and any further writes will overwrite the buffer. WCOL is cleared by hardware when the buff-
ered byte is loaded into the shift register and transmission begins. If the master SPI is currently
idle, i.e. if this is the first byte, then after loading SPDR, transmission of the byte starts and
WCOL is cleared immediately. While this byte is transmitting, the next byte may be written to
SPDR. The Load Enable flag (LDEN) in SPSR can be used to determine when transmission has
started. LDEN is asserted during the first four bit slots of a SPI transfer. The master CPU should
first check that LDEN is set and that WCOL is cleared before loading the next byte. In enhanced
mode, if WCOL is set when a transfer completes, i.e. the next byte is available, then the SPI
immediately loads the buffered byte into the shift register, resets WCOL, and continues trans-
mission without stopping and restarting the clock generator. As long as the CPU can keep the
write buffer full in this manner, multiple bytes may be transferred with minimal latency between
bytes.
25
3286C MICRO 1/05
PIN CONTROL LOGIC
SPR1
SPR0
MSTR
SPE
DORD
SPIE
SPE
WCOL
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
SPIF
Table 15-1. SPCR  SPI Control Register
SPCR Address = D5H Reset Value = 0000 0100B
Not Bit Addressable
SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0
Bit 76543210
Symbol Function
SPI interrupt enable. This bit, in conjunction with the ES bit in the IE register, enables SPI interrupts: SPIE = 1 and ES = 1
SPIE
enable SPI interrupts. SPIE = 0 disables SPI interrupts.
SPI enable. SPI = 1 enables the SPI channel and connects SS, MOSI, MISO and SCK to pins P1.4, P1.5, P1.6, and P1.7.
SPE
SPI = 0 disables the SPI channel.
DORD Data order. DORD = 1 selects LSB first data transmission. DORD = 0 selects MSB first data transmission.
MSTR Master/slave select. MSTR = 1 selects Master SPI mode. MSTR = 0 selects slave SPI mode.
Clock polarity. When CPOL = 1, SCK is high when idle. When CPOL = 0, SCK of the master device is low when not
CPOL
transmitting. Please refer to figure on SPI clock phase and polarity control.
Clock phase. The CPHA bit together with the CPOL bit controls the clock and data relationship between master and slave.
CPHA
Please refer to figure on SPI clock phase and polarity control.
SPI clock rate select. These two bits control the SCK rate of the device configured as master. SPR1 and SPR0 have no
effect on the slave. The relationship between SCK and the oscillator frequency, FOSC., is as follows:
SPR1SPR0SCK = FOSC. divided by:
SPR0
0 0 4
SPR1
0 1 16
1 0 64
1 1 128
Notes: 1. Set up the clock mode before enabling the SPI: set all bits needed in SPCR except the SPE bit, then set SPE.
2. Enable the master SPI prior to the slave device.
3. Slave echoes master on next Tx if not loaded with new data.
26
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Table 15-2. SPSR  SPI Status Register
SPSR Address = AAH Reset Value = 000X XX00B
Not Bit Addressable
SPIF WCOL LDEN    DISSO ENH
Bit 76543210
Symbol Function
SP interrupt flag. When a serial transfer is complete, the SPIF bit is set and an interrupt is generated if SPIE = 1 and ES
SPIF
= 1. The SPIF bit is cleared by reading the SPI status register followed by reading/writing the SPI data register.
When ENH = 0: Write collision flag. The WCOL bit is set if the SPI data register is written during a data transfer. During
data transfer, the result of reading the SPDR register may be incorrect, and writing to it has no effect. The WCOL bit (and
the SPIF bit) are cleared by reading the SPI status register followed by reading/writing the SPI data register.
WCOL
When ENH = 1: WCOL works in Enhanced mode as Tx Buffer Full. Writing during WCOL = 1 in enhanced mode will
overwrite the waiting data already present in the Tx Buffer. In this mode, WCOL is no longer reset by the SPIF reset but
is reset when the write buffer has been unloaded into the serial shift register.
Load enable for the Tx buffer in enhanced SPI mode.
LDEN
When ENH is set, it is safe to load the Tx Buffer while LDEN = 1 and WCOL = 0. LDEN is high during bits 0 - 3 and is low
during bits 4 - 7 of the SPI serial byte transmission time frame.
Disable slave output bit.
When set, this bit causes the MISO pin to be tri-stated so more than one slave device can share the same interface with
DISSO
a single master. Normally, the first byte in a transmission could be the slave address and only the selected slave should
clear its DISSO bit.
Enhanced SPI mode select bit. When ENH = 0, SPI is in normal mode, i.e. without write double buffering.
ENH
When ENH = 1, SPI is in enhanced mode with write double buffering. The Tx buffer shares the same address with the
SPDR register.
Table 15-3. SPDR  SPI Data Register
SPDR Address = 86H
Reset Value = 00H (after cold reset)
Not Bit Addressable
unchanged (after warm reset)
SPD7 SPD6 SPD5 SPD4 SPD3 SPD2 SPD1 SPD0
Bit 76543210
27
3286C MICRO 1/05
Figure 15-3. SPI Shift Register Diagram
7
Serial In
Serial Master Serial Slave
8
2:1 2:1
D Q D Q
MUX MUX
Serial Out
LATCH LATCH
CLK CLK
8
Parallel Master Parallel Slave
Transmit (Write Buffer) (Read Buffer) Receive
Byte Byte
8 8 8
D Q D Q
LATCH LATCH
CLK CLK
The CPHA (Clock PHAse), CPOL (Clock POLarity), and SPR (Serial Peripheral clock Rate =
baud rate) bits in SPCR control the shape and rate of SCK. The two SPR bits provide four possi-
ble clock rates when the SPI is in master mode. In slave mode, the SPI will operate at the rate of
the incoming SCK as long as it does not exceed the maximum bit rate. There are also four pos-
sible combinations of SCK phase and polarity with respect to the serial data. CPHA and CPOL
determine which format is used for transmission. The SPI data transfer formats are shown in
Figure 15-4 and Figure 15-5. To prevent glitches on SCK from disrupting the interface, CPHA,
CPOL, and SPR should be set up before the interface is enabled, and the master device should
be enabled before the slave device(s).
Table 15-4. SPI Master Characteristics
Symbol Parameter Min Max Units
tCLCL Oscillator Period 41.6 ns
tSCK Serial Clock Cycle Time 4tCLCL ns
tSHSL Clock High Time tSCK/2 - 25 ns
tSLSH Clock Low Time tSCK/2 - 25 ns
tSR Rise Time 25 ns
tSF Fall Time 25 ns
tSIS Serial Input Setup Time 10 ns
tSIH Serial Input Hold Time 10 ns
tSOH Serial Output Hold Time 10 ns
tSOV Serial Output Valid Time 35 ns
28
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Table 15-5. SPI Slave Characteristics
Symbol Parameter Min Max Units
tCLCL Oscillator Period 41.6 ns
tSCK Serial Clock Cycle Time 4tCLCL ns
tSHSL Clock High Time 1.5 tCLCL - 25 ns
tSLSH Clock Low Time 1.5 tCLCL - 25 ns
tSR Rise Time 25 ns
tSF Fall Time 25 ns
tSIS Serial Input Setup Time 10 ns
tSIH Serial Input Hold Time 10 ns
tSOH Serial Output Hold Time 10 ns
tSOV Serial Output Valid Time 35 ns
tSOE Output Enable Time 10 ns
tSOX Output Disable Time 25 ns
tSSE Slave Enable Lead Time 10 ns
tSSD Slave Disable Lag Time 0 ns
Figure 15-4. SPI Master Timing (CPHA = 0)
SS
tSF
tSCK tSR
tSHSL tSLSH
SCK
(CPOL = 0)
SCK
tSLSH tSHSL
(CPOL = 1)
tSIS tSIH
MISO
tSOH tSOV
MOSI
29
3286C MICRO 1/05
Figure 15-5. SPI Slave Timing (CPHA = 0)
SS
tSCK tSR tSSD
tSSE
tSF
tSHSL tSLSH
SCK
(CPOL = 0)
SCK
tSLSH
tSHSL
(CPOL= 1)
tSOX
tSOE tSOV tSOH
MISO
tSIS tSIH
MOSI
Figure 15-6. SPI Master Timing (CPHA = 1)
SS
tSCK
tSF tSR
tSHSL tSLSH
SCK
(CPOL = 0)
SCK
tSLSH tSHSL
(CPOL = 1)
tSIS tSIH
MISO
tSOH tSOV
MOSI
Figure 15-7. SPI Slave Timing (CPHA = 1)
SS
tSSE tSCK
tSF tSR
tSSD
tSLSH
tSHSL
SCK
(CPOL = 0)
SCK
tSLSH
tSHSL
(CPOL = 1)
tSOE tSOV tSOH tSOX
MISO
tSIS tSIH
MOSI
30
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Figure 15-8. SPI Transfer Format with CPHA = 0
Note: *Not defined but normally MSB of character just received
Figure 15-9. SPI Transfer Format with CPHA = 1
SCK CYCLE #
1 2 3 4 5 6 7 8
(FOR REFERENCE)
SCK (CPOL = 0)
SCK (CPOL = 1)
MOSI
MSB 6 5 4 3 2 1 LSB
(FROM MASTER)
MISO
MSB 6 5 4 3 2 1 LSB
*
(FROM SLAVE)
SS (TO SLAVE)
Note: *Not defined but normally LSB of previously transmitted character
16. Interrupts
The AT89S8253 has a total of six interrupt vectors: two external interrupts (INT0 and INT1),
three timer interrupts (Timers 0, 1, and 2), and the serial port interrupt. These interrupts are all
shown in Figure 16-1.
Each of these interrupt sources can be individually enabled or disabled by setting or clearing a
bit in Special Function Register IE. IE also contains a global disable bit, EA, which disables all
interrupts at once.
Note that Table 16-1 shows that bit position IE.6 is unimplemented. User software should not
write a 1 to this bit position, since it may be used in future AT89 products.
Timer 2 interrupt is generated by the logical OR of bits TF2 and EXF2 in register T2CON. Nei-
ther of these flags is cleared by hardware when the service routine is vectored to. In fact, the
service routine may have to determine whether it was TF2 or EXF2 that generated the interrupt,
and that bit will have to be cleared in software.
The serial interrupt is the logical OR of bits RI and TI in register SCON and also bit SPIF in
SPSR (if SPIE in SPCR is set). None of these flags is cleared by hardware when the service rou-
tine is vectored to. The service routine may have to determine whether the UART or SPI
generated the interrupt.
The Timer 0 and Timer 1 flags, TF0 and TF1, are set at S5P2 of the cycle in which the timers
overflow. The values are then polled by the circuitry in the next cycle. However, the Timer 2 flag,
TF2, is set at S2P2 and is polled in the same cycle in which the timer overflows.
31
3286C MICRO 1/05
Table 16-1. Interrupt Enable (IE) Register
IE Address = A8H Reset Value = 0X00 0000B
Bit Addressable
EA  ET2 ES ET1 EX1 ET0 EX0
Enable Bit = 1 enables the interrupt.
Enable Bit = 0 disables the interrupt.
Symbol Position Function
Disables all interrupts. If EA = 0, no interrupt is acknowledged. If EA = 1, each interrupt source is individually
EA IE.7
enabled or disabled by setting or clearing its enable bit.
 IE.6 Reserved.
ET2 IE.5 Timer 2 interrupt enable bit.
ES IE.4 SPI and UART interrupt enable bit.
ET1 IE.3 Timer 1 interrupt enable bit.
EX1 IE.2 External interrupt 1 enable bit.
ET0 IE.1 Timer 0 interrupt enable bit.
EX0 IE.0 External interrupt 0 enable bit.
User software should never write 1s to reserved bits, because they may be used in future AT89 products.
Figure 16-1. Interrupt Sources
32
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
17. Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier that can be
configured for use as an on-chip oscillator, as shown in Figure 17-1. Either a quartz crystal or
ceramic resonator may be used. To drive the device from an external clock source, XTAL2
should be left unconnected while XTAL1 is driven, as shown in Figure 17-2.
Figure 17-1. Oscillator Connections
Note: C1, C2 = 30 pF Ä… 10 pF for Crystals
= 40 pF Ä… 10 pF for Ceramic Resonators
Figure 17-2. External Clock Drive Configuration
18. Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-chip peripherals remain active. This
mode is invoked by software. The content of the on-chip RAM and all the special functions regis-
ters remain unchanged during this mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
Note that when idle mode is terminated by a hardware reset, the device normally resumes pro-
gram execution from where it left off, up to two machine cycles before the internal reset
algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but
access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a
port pin when idle mode is terminated by a reset, the instruction following the one that invokes
idle mode should not write to a port pin or to external memory.
Table 18-1. Status of External Pins During Idle and Power-down Modes
Mode Program Memory ALE PSEN PORT0 PORT1 PORT2 PORT3
Idle Internal 1 1 Data Data Data Data
Idle External 1 1 Float Data Address Data
Power-down Internal 0 0 Data Data Data Data
Power-down External 0 0 Float Data Data Data
33
3286C MICRO 1/05
19. Power-down Mode
In the power-down mode, the oscillator is stopped and the instruction that invokes power-down
is the last instruction executed. The on-chip RAM and Special Function Registers retain their
values until the power-down mode is terminated. Exit from power-down can be initiated either by
a hardware reset or by an enabled external interrupt. Reset redefines the SFRs but does not
change the on-chip RAM. The reset should not be activated before VCC is restored to its normal
operating level and must be held active long enough to allow the oscillator to restart and
stabilize.
To exit power-down via an interrupt, external interrupt pin P3.2 or P3.3 must be kept low for at
least the specified required crystal oscillator start up time. Afterwards, the interrupt service rou-
tine starts at the rising edge of the external interrupt pin if the SFR bit AUXR.1 is set. If AUXR.1
is reset (cleared), execution starts after a self-timed interval of 2 ms (nominal) from the falling
edge of the external interrupt pin.
20. Program Memory Lock Bits
The AT89S8253 has three lock bits that can be left unprogrammed (U) or can be programmed
(P) to obtain the additional features listed in Table 20-1.
When lock bit 1 is programmed, the logic level at the EA pin is sampled and latched during reset.
If the device is powered up without a reset, the latch initializes to a random value and holds that
value until reset is activated. The latched value of EA must agree with the current logic level at
that pin in order for the device to function properly.
Once programmed, the lock bits can only be unprogrammed with the Chip Erase operation in
either the parallel or serial modes.
Table 20-1. Lock Bit Protection Modes(1)
Program Lock Bits
LB1 LB2 LB3 Protection Type
1 U U U No internal memory lock feature.
MOVC instructions executed from external program memory are
disabled from fetching code bytes from internal memory. EA is sampled
2 P U U
and latched on reset and further programming of the Flash memory
(parallel or serial mode) is disabled.
3 P P U Same as Mode 2, but parallel or serial verify are also disabled.
4 P P P Same as Mode 3, but external execution is also disabled.
Note: 1. U = Unprogrammed
P = Programmed
34
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
21. Programming the Flash and EEPROM
Atmel s AT89S8253 Flash microcontroller offers 12K bytes of In-System reprogrammable Flash
code memory and 2K bytes of EEPROM data memory.
The AT89S8253 is normally shipped with the on-chip Flash code and EEPROM data memory
arrays in the erased state (i.e. contents = FFH) and ready to be programmed. This device sup-
ports a parallel programming mode and a serial programming mode. The serial programming
mode provides a convenient way to reprogram the AT89S8253 inside the user s system. The
parallel programming mode is compatible with conventional third-party Flash or EPROM
programmers.
The code and data memory arrays are mapped via separate address spaces in the parallel and
serial programming modes: 0000H to 2FFFH for code memory and 000H to 7FFH for data
memory.
The code and data memory arrays in the AT89S8253 are programmed byte-by-byte or by page
in either programming mode. To reprogram any non-blank byte in the parallel or serial mode, the
user needs to invoke the Chip Erase operation first to erase both arrays.
Parallel Programming Algorithm: To program and verify the AT89S8253 in the parallel pro-
gramming mode, the following sequence is recommended (see Figure 27-1):
1. Power-up sequence:
a. Apply power between VCC and GND pins.
b. Set RST pin to  H .
c. Apply a 3 MHz to 24 MHz clock to XTAL1 pin and wait for at least 10 ms.
2. Set PSEN pin to  L
a. ALE pin to  H
b. EA pin to  H and all other pins to  H .
3. Raise EA/VPP to 12V to enable Flash programming, erase or verification. Enable the
P3.0 pull-up (10 K&! typical) for RDY/BSY operation.
4. Apply the appropriate combination of  H or  L logic levels to pins P3.3, P3.4, P3.5,
P3.6, P3.7 to select one of the programming operations shown in the Flash Program-
ming Modes table.
5. Apply the desired byte address to pins P1.0 to P1.7 and P2.0 to P2.5.
a. Apply data to pins P0.0 to P0.7 for write code operation.
6. Pulse ALE/PROG once to load a byte in the code memory array, the data memory
array, or the lock bits.
7. Repeat steps 5 and 6, changing the address and data for up to 64 bytes in the code
memory page or 32 bytes in the data memory (EEPROM) page. When loading a page
with individual bytes, the interval between consecutive byte loads should be no longer
than 150 µs. Otherwise the device internally times out and assumes that the page load
sequence is completed, rejecting any further loads before the page programming
sequence has finished. This timing restriction also applies to Page Write of the 64-byte
User Row.
8. After the last byte of the current page has been loaded, wait for 5 ms or monitor the
RDY/BUSY pin until it transitions high. The page write cycle is self-timed and typically
takes less than 5 ms.
9. To verify the last byte of the page just programmed, bring pin P3.4 to  L and read the
programmed data at pins P0.0 to P0.7.
35
3286C MICRO 1/05
10. Repeat steps 4 through 7 changing the address and data for the entire array or until the
end of the object file is reached.
11. Power-off sequence:
a. Tri-state the address and data inputs.
b. Disable the P3.0 pullup used for RDY/BUSY operation.
c. Set XTAL1 to  L .
d. Set RST and EA pins to  L .
e. Turn VCC power off.
Data Polling: The AT89S8253 features DATA Polling to indicate the end of any programming
cycle. During a write cycle in the parallel or serial programming mode, an attempted read of the
last loaded byte will result in the complement of the written datum on P0.7 (parallel mode), and
on the MSB of the serial output byte on MISO (serial mode). Once the write cycle has been com-
pleted, true data are valid on all outputs, and the next cycle may begin. DATA Polling may begin
any time after a write cycle has been initiated.
Ready/Busy: The progress of byte programming in the parallel programming mode can also be
monitored by the RDY/BSY output signal. Pin P3.0 is pulled Low after ALE goes High during
programming to indicate BUSY. P3.0 is pulled High again when programming is done to indicate
READY. P3.0 needs an external pullup (typical 10 K&!) when functioning as RDY/BSY.
Program Verify: If lock bits LB1 and LB2 have not been programmed, the programmed Code or
Data byte can be read back via the address and data lines for verification. The state of the lock
bits can also be verified directly in the parallel and serial programming modes.
Chip Erase: Both Flash and EEPROM arrays are erased electrically at the same time. In the
parallel programming mode, Chip Erase is initiated by using the proper combination of control
signals. The code and data arrays are written with all  1 s during the Chip Erase operation. The
User Row will also be erased if the UsrRowProEn fuse (Fuse3) = 0 (enabled state).
In the serial programming mode, a chip erase operation is initiated by issuing the Chip Erase
instruction. In this mode, Chip Erase is self-timed and also takes about 8 ms.
During Chip Erase, a serial read from any address location will return 00H at the data outputs.
Serial Programming Fuse: A programmable fuse is available to disable Serial Programming if
the user needs maximum system security. The Serial Programming Fuse can be enabled/dis-
abled in both the Parallel/Serial Programming Modes.
The AT89S8253 is shipped with the Serial Programming Mode enabled.
Reading the Signature Bytes: The signature bytes are read by the same procedure as a nor-
mal verification of locations 030H and 031H, except that P3.6 and P3.7 must be pulled to a logic
low. The values returned are as follows:
(030H) = 1EH indicates manufactured by Atmel
(031H) = 73H indicates AT89S8253
36
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
22. Programming Interface
Every code byte in the Flash and EEPROM arrays can be written, and the entire array can be
erased, by using the appropriate combination of control signals. The write operation cycle is self-
timed and once initiated, will automatically time itself to completion.
Most worldwide major programming vendors offer support for the Atmel AT89 microcontroller
series. Please contact your local programming vendor for the appropriate software revision.
23. Serial Downloading
Both the code and data memory arrays can be programmed using the serial SPI bus while RST
is pulled to VCC. The serial interface consists of pins SCK, MOSI (input) and MISO (output). After
RST is set high, the Programming Enable instruction must be executed first before other opera-
tions can be executed.
The Chip Erase operation turns the content of every memory location in both the Code and Data
arrays into FFH.
The code and data memory arrays have separate address spaces:
0000H to 2FFFH for code memory and 000H to 7FFH for data memory.
Either an external system clock is supplied at pin XTAL1 or a crystal needs to be connected
across pins XTAL1 and XTAL2. The maximum serial clock (SCK) frequency should be less than
1/16 of the crystal frequency. With a 24 MHz oscillator clock, the maximum SCK frequency is 1.5
MHz.
24. Serial Programming Algorithm
To program and verify the AT89S8253 in the serial programming mode, the following sequence
is recommended:
1. Power-up sequence:
a. Apply power between VCC and GND pins.
b. Set RST pin to  H .
If a crystal is not connected across pins XTAL1 and XTAL2, apply a 3 MHz to 24 MHz clock to
XTAL1 pin and wait for at least 10 ms with RST pin high and P1.7 (SCK) low.
2. Enable serial programming by sending the Programming Enable serial instruction to pin
MOSI/P1.5. The frequency of the shift clock supplied at pin SCK/P1.7 needs to be less
than the CPU clock at XTAL1 divided by 16.
3. The code or data array is programmed one byte or one page at a time by supplying the
address and data together with the appropriate Write instruction. The write cycle is self-
timed and typically takes less than 4.0 ms at 5V.
4. Any memory location can be verified by using the Read instruction which returns the
content at the selected address at serial output MISO/P1.6.
5. At the end of a programming session, RST can be set low to commence normal
operation.
Power-off sequence (if needed):
1. Set XTAL1 to  L (if a crystal is not used).
2. Set RST to  L .
3. Turn VCC power off.
37
3286C MICRO 1/05
25. Serial Programming Instruction
The Instruction Set for Serial Programming follows a 4-byte protocol and is shown in Table 25-1.
Table 25-1. Serial Programming Instruction Set
Instruction Format
Instruction Byte 1 Byte 2 Byte 3 Byte 4 Byte n Operation
1010 1100 0101 0011 xxxx xxxx xxxx xxxx
Enable Serial Programming while
Programming Enable
RST is high
1010 1100 100x xxxx xxxx xxxx xxxx xxxx
Chip Erase both the 12K and 2K
Chip Erase
memory arrays
0100 0000 xx
Write Program Memory Write data to Program Memory 
(Byte Mode) Byte Mode
0010 0000 xx
Read Program Memory Read data from Program Memory 
(Byte Mode) Byte Mode
0101 0000 xx 00 0000
Write Program Memory Write data to Program Memory 
Byte 0 ... Byte 63
(Page Mode) Page Mode (64 bytes)
0011 0000 xx 00 0000
Read Program Memory Read data from Program Memory 
Byte 0 ... Byte 63
(Page Mode) Page Mode (64 bytes)
1100 0000 xxxx x
Write Data Memory Write data to Data Memory
(Byte Mode)  Byte Mode
1010 0000 xxxx x
Read Data Memory Read data from Data Memory  Byte
(Byte Mode) Mode
1101 0000 xxxx x 0 0000
Write Data Memory Write data to Data Memory  Page
Byte 0 ... Byte 31
(Page Mode) Mode (32 bytes)
1011 0000 xxxx x 0 0000
Read Data Memory Read data from Data Memory
Byte 0 ... Byte 31
(Page Mode)  Page Mode (32 bytes)
1010 1100 0001 xxxx xxxx xxxx xxxx
Write User Fuses
Write user fuse bits (refer to next
page for the fuse definitions)
0010 0001 xxxx xxxx xxxx xxxx xxxx
Read User Fuses Read back status of user fuse bits
1010 1100 1110 0 xxxx xxxx xxxx xxxx
Write the lock bits (write a  0 to
Write Lock Bits lock)
0010 0100 xxxx xxxx xxxx xxxx xxxx x
Read back current status of the lock
Read Lock Bits bits (a programmed lock bit reads
back as a  0 )
0100 0010 xxxx xxxx xx
Write User Sgn. Byte
0010 0010 xxxx xxxx xx
Read User Sgn. Byte
0101 0010 xxxx xxxx xxxx xxxx
Write User Sgn. Page Byte 0 ... Byte 63
0011 0010 xxxx xxxx xxxx xxxx
Read User Sgn. Page Byte 0 ... Byte 63
0010 1000 xxxx xxxx xx
Read Signature Byte
Read ATMEL Sgn. Byte
After Reset signal is high, SCK should be low for at least 64 system clocks before it goes high to clock in the enable data
bytes. No pulsing of Reset signal is necessary. SCK should be no faster than 1/16 of the system clock at pin XTAL1.
For Page Read/Write, the data always starts from byte 0 to 31 or 63. After the command byte and upper address byte are
latched, each byte thereafter is treated as data until all 32 or 64 bytes are shifted in/out. Then the next instruction will be
ready to be decoded.
38
AT89S8253 [Preliminary]
3286C MICRO 1/05
A7
A7
A6
A6
A5
A5
A4
A4
A3
A3
A2
A2
A1
A1
A0
A0
D7
D7
D6
D6
D5
D5
D4
D4
D3
D3
D2
D2
D1
D1
D0
D0
A7
A7
A6
A6
A9
A9
A9
A9
A8
A8
A8
A8
A13
A13
A13
A13
A12
A12
A12
A12
A11
A11
A11
A11
A10
A10
A10
A10
A7
A7
A6
A6
A5
A5
A4
A4
A3
A3
A2
A2
A1
A1
A0
A0
D7
D7
D6
D6
D5
D5
D4
D4
D3
D3
D2
D2
D1
D1
D0
D0
A9
A9
A9
A9
A8
A8
A8
A8
A7
A7
A6
A6
A5
A5
A10
A10
A10
A10
FUSE4
FUSE3
FUSE2
FUSE1
FUSE4
FUSE3
FUSE2
FUSE1
LB3
LB2
LB1
LB3
LB2
LB1
A9
A9
A8
A8
D7
D7
D6
D6
D5
D5
D4
D4
D3
D3
D2
D2
D1
D1
D0
D0
A13
A13
A12
A12
A11
A11
A10
A10
A9
A8
D7
D6
D5
D4
D3
D2
D1
D0
A13
A12
A11
A10
 AT89S8253 [Preliminary]
26. Flash and EEPROM Parallel Programming Modes
ALE
Address
Data I/O P2.5:0,
Mode RST PSEN EA P3.3 P3.4 P3.5 P3.6 P3.7 P0.7:0 P1.7:0
Serial Prog. Modes(1) H h h
Chip Erase(2) H L 1.0 µs 12V H L H L L X X
Page Write(3)(4)(5) 12K Code H L 1.0 µs 12V L H H H H DI ADDR
Read 12K Code H L H 12V L L H H H DO ADDR
Page Write(3)(4)(6) 2K Data H L 1.0 µs 12V L H L H H DI ADDR
Read 2K Data H L H 12V L L L H H DO ADDR
Bit - 1 D0 = 0 X
Write Lock Bits(2)(4) Bit - 2 H L 1.0 µs 12V H L H H L D1 = 0 X
Bit - 3 D2 = 0 X
Bit - 1 D0 X
Read Lock Bits Bit - 2 H L H 12V H H H L L D1 X
Bit - 3 D2 X
Page Write(3)(4)(5) User Row H L 1.0 µs 12V H L H H H DI 0 - 3FH
Read User Row H L H 12V L L H L H DO 0 - 3FH
Read Sig. Row H L H 12V L L H L L DO 0 - 3FH
SerialPrgEn D0 = 0 X
Fuse1
SerialPrgDis D0 = 1 X
x2 ClockEn D1 = 0 X
Fuse2
x2 ClockDis D1 = 1 X
Write
H L 1.0 µs 12V L H H L H
Fuse(2)(4)
UsrRowPrgEn D2 = 0 X
Fuse3
UsrRowPrgDis D2 = 1 X
External Clock En D3 = 0 X
Fuse4
Crystal Clock En D3 = 1 X
SerialPrg (Fuse1) D0 X
x2 Clock (Fuse2) D1 X
UsrRow Prg
Read Fuse H L H 12V H H H L H
D2 X
(Fuse3)
Clock Select
D2 X
(Fuse4)
Notes: 1. See detailed timing for Serial Programming Mode.
2. Internally timed for 8.0 ms.
3. Internally timed for 8.0 ms. Programming begins 150 µs (minimum) after the last write pulse.
4. P3.0 is pulled low during programming to indicate RDY/BSY
5. 1 to 64 bytes can be programmed at a time per page.
6. 1 to 32 bytes can be programmed at a time per page.
39
3286C MICRO 1/05
}
}
}
}
Figure 26-1. Programming the Flash/EEPROM Memory (Parallel Mode)
VCC VCC
AT89S8253 AT89S8253
A0 - A7 A0 - A7
VCC VCC
ADDR. P1 ADDR. P1
0000H/37FFH 0000H/37FFH
PGM PGM
P2.0 - P2.5 P0 P2.0 - P2.5 P0
DATA DATA
A8 - A13 A8 - A13
P3.3 P3.3
ALE PROG ALE PROG
P3.4 P3.4
SEE FLASH SEE FLASH
PROGRAMMING PROGRAMMING
P3.5 P3.5
MODES TABLE MODES TABLE
P3.6 P3.6
P3.7 P3.7
XTAL2 EA VPP EA VPP
3-24 MHz
P3.0 RDY/BSY P3.0 RDY/BSY
(USE 10K (USE 10K
PULLUP) PULLUP)
3-12 MHz
XTAL1 RST VIH XTAL1 RST VIH
EXTERNAL
CLOCK
GND PSEN GND PSEN
Oscillator Bypass Oscillator Bypass
Fuse (Fuse4) Off Fuse (Fuse4) On
Figure 26-2. Verifying the Flash/EEPROM Memory (Parallel Mode)
VCC VCC
AT89S8253 AT89S8253
A0 - A7 A0 - A7
VCC VCC
ADDR. P1 ADDR. P1
PGM DATA PGM DATA
0000H/37FFH 0000H/37FFH
P0 P0
P2.0 - P2.5 P2.0 - P2.5
(USE 10K (USE 10K
A8 - A13 A8 - A13
PULLUPS) PULLUPS)
P3.3 P3.3
ALE VI H ALE VI H
P3.4 P3.4
SEE FLASH SEE FLASH
PROGRAMMING PROGRAMMING
P3.5 P3.5
MODES TABLE MODES TABLE
P3.6 P3.6
P3.7 P3.7
VPP VPP
XTAL2 EA EA
3-24 Mhz
3-12 MHz
VI H VI H
XTAL1 RST XTAL1 RST
EXTERNAL
CLOCK
GND PSEN GND PSEN
Oscillator Bypass Oscillator Bypass
Fuse (Fuse4) Off Fuse (Fuse4) On
40
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
Figure 26-3. Flash/EEPROM Serial Downloading
2.7V to 5.5V 2.7V to 5.5V
AT89S8253 AT89S8253
VCC VCC
INSTRUCTION INSTRUCTION
P1.5/MOSI P1.5/MOSI
INPUT INPUT
P1.6/MISO P1.6/MISO
DATA OUTPUT DATA OUTPUT
P1.7/SCK P1.7/SCK
CLOCK IN CLOCK IN
XTAL2
3-24 MHz
3-12 MHz
XTAL1 RST VIH XTAL1 RST VIH
EXTERNAL
CLOCK
GND GND
Oscillator Bypass Oscillator Bypass
Fuse (Fuse4) Off Fuse (Fuse4) On
41
3286C MICRO 1/05
27. Flash Programming and Verification Characteristics  Parallel Mode
TA = 20°C to 30°C, VCC = 4.0V to 5.5V
Min Max Units
Symbol Parameter
VPP Programming Enable Voltage 11.5 12.5 V
IPP Programming Enable Current 1.0 mA
1/tCLCL Oscillator Frequency 3 24 MHz
tPWRUP Power On to RST High (1) 10 µs
tRHX RST High to XTAL Start 10 µs
tOSTL Oscillator Settling Time 10 ms
tHSTL High Voltage Settling Time 10 µs
tMSTP Mode Setup to PROG Low 1 µs
tASTP Address Setup to PROG Low 1 µs
tDSTP Data Setup to PROG Low 1 µs
tPGW PROG Width 1 µs
tAHLD Address Hold after PROG 1µs
tDHLD Data Hold after PROG 1µs
tBLT Byte Load Period 1 150 µs
tPHBL PROG High to BUSY Low 256 µs
tWC Write Cycle Time(2) 4.5 ms
tMHLD Mode Hold After BUSY Low 10 µs
tVFY Address to Data Verify Valid 1 µs
tPSTP PROG Setup to VPP High 10 µs
tPHLD PROG Hold after VPP Low 10 µs
tPLX PROG Low to XTAL Halt 1 µs
tXRL XTAL Halt to RST Low 1 µs
tPWRDN RST Low to Power Off 1 µs
Notes: 1. Power On occurs once VCC reaches 2.4V.
2. 9 ms if Chip Erase.
42
AT89S8253 [Preliminary]
3286C MICRO 1/05
VCC
tPWRUP
tPWRDN
RST
tRHX tXRL
Running at 3 MHz
XTAL 1
tPLX
PSEN
tOSTL
tHSTL
EA/VPP
tPGW tBLT
tPSTP tMSTP
tPHLD
ALE/PROG
tMHLD
tASTP
P3.3...P3.7
tDSTP tAHLD
tMSTP
P1.0...P1.7 ADDR0 ADDR1 ADDR0 ADDR1
and P2.0...P2.5
tDHLD
DATA0 DATA1 DATA0 DATA1
PORT 0
tVFY
P3.0
(RDY/BSY)
tPHBL
tWC
3286C MICRO 1/05
Figure 27-1.
Flash/EEPROM Programming and Verification Waveforms  Parallel Mode
AT89S8253 [Preliminary]
43
28. Serial Downloading Waveforms (SPI Mode 1 --> CPOL = 0, CPHA = 1)
7 6 5 4 3 2 1 0
SERIAL DATA INPUT
MSB LSB
MOSI/P1.5
SERIAL DATA OUTPUT
MSB LSB
MISO/P1.6
SCK/P1.7
29. Serial Programming Characteristics
Figure 29-1. Serial Programming Timing
Change Sample
Outputs Inputs
tSLSH tSHSL
SCK
tOVSL
tSHOX
MOSI
MISO
tSHIV
Table 29-1. Serial Programming Characteristics, TA = -40°C to 85°C, VCC = 2.7V - 5.5V (Unless Otherwise Noted)
Symbol Parameter Min Typ Max Units
1/tCLCL Oscillator Frequency 3 24 MHz
tCLCL Oscillator Period 41.6 33.3 ns
tSHSL SCK Pulse Width High 8 tCLCL ns
tSLSH SCK Pulse Width Low 8 tCLCL ns
tOVSL MOSI Setup to SCK Low tCLCL ns
tSHOX MOSI Hold after SCK Low 2 tCLCL ns
tSHIV SCK High to MISO Valid 10 16 32 ns
tERASE Chip Erase Instruction Cycle Time 9 ms
tSWC Serial Page Write Cycle Time 4.5 ms
44
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
30. Absolute Maximum Ratings*
*NOTICE: Stresses beyond those listed under  Absolute
Operating Temperature.................................. -55°C to +125°C
Maximum Ratings may cause permanent dam-
age to the device. This is a stress rating only and
Storage Temperature ..................................... -65°C to +150°C
functional operation of the device at these or any
Voltage on Any Pin other conditions beyond those indicated in the
with Respect to Ground .....................................-1.0V to +7.0V operational sections of this specification is not
implied. Exposure to absolute maximum rating
Maximum Operating Voltage ............................................ 6.6V
conditions for extended periods may affect device
reliability.
DC Output Current...................................................... 15.0 mA
31. DC Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VCC = 2.7 to 5.5V, unless otherwise noted
Symbol Parameter Condition Min Max
VIL Input Low-voltage (Except EA) -0.5V 0.2 VCC - 0.1V
VIL1 Input Low-voltage (EA) -0.5V 0.2 VCC - 0.3V
VIH Input High-voltage (Except XTAL1, RST) 0.2 VCC + 0.9V VCC + 0.5V
VIH1 Input High-voltage (XTAL1, RST) 0.7 VCC VCC + 0.5V
VOL Output Low-voltage(1) IOL = 10 mA, VCC = 4.0V, TA = 85°C 0.4V
IOH = -60 µA, TA = 85°C 2.4V
Output High-voltage
VOH When Weak Pull Ups are Enabled IOH = -25 µA, TA = 85°C 0.75 VCC
(Ports 1, 2, 3, ALE, PSEN)
IOH = -10 µA, TA = 85°C 0.9 VCC
IOH = -40 mA, TA = 85°C 2.4V
Output High-voltage
When Strong Pull Ups are Enabled
VOH1 IOH = -25 mA, TA = 85°C 0.75 VCC
(Port 0 in External Bus Mode, P1, 2, 3,
ALE, PSEN)
IOH = -10 mA, TA = 85°C 0.9 VCC
IIL Logical 0 Input Current (Ports 1, 2, 3) VIN = 0.45V, VCC = 5.5V, TA = -40°C -50 µA
Logical 1 to 0 Transition Current (Ports
ITL VIN = 2V, VCC = 5.5V, TA = -40°C -352 µA
1, 2, 3)
ILI Input Leakage Current (Port 0, EA) 0.45V< VIN < VCC Ä…10 µA
RRST Reset Pull-down Resistor 50 K&! 150 K&!
CIO Pin Capacitance Test Freq. = 1 MHz, TA = 25°C 10 pF
Active Mode, 12 MHz, VCC = 5.5V, TA = -40°C 25 mA
Power Supply Current
Idle Mode, 12 MHz, VCC = 5.5V, TA = -40°C 6.5 mA
ICC
VCC = 5.5V, TA = -40°C 100 µA
Power-down Mode(2)
VCC = 4.0V, TA = -40°C 40 µA
Notes: 1. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin: 10 mA,
Maximum IOL per 8-bit port:15 mA,
Maximum total IOL for all output pins: 71 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test conditions.
2. Minimum VCC for Power-down is 2V.
45
3286C MICRO 1/05
32. AC Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VCC = 2.7 to 5.5V, unless otherwise noted.
Under operating conditions, load capacitance for Port 0, ALE/PROG, and PSEN = 100 pF; load capacitance for all other
outputs = 80 pF.
32.1 External Program and Data Memory Characteristics
Variable Oscillator
Symbol Parameter Min Max Units
1/tCLCL Oscillator Frequency 0 24 MHz
tLHLL ALE Pulse Width 2tCLCL - 12 ns
tAVLL Address Valid to ALE Low tCLCL - 12 ns
tLLAX Address Hold after ALE Low tCLCL - 16 ns
tLLIV ALE Low to Valid Instruction In 4tCLCL - 50 ns
tLLPL ALE Low to PSEN Low tCLCL - 12 ns
tPLPH PSEN Pulse Width tCLCL ns
tPLIV PSEN Low to Valid Instruction In 3tCLCL - 50 ns
tPXIX Input Instruction Hold after PSEN -10 ns
tPXIZ Input Instruction Float after PSEN tCLCL - 20 ns
tPXAV PSEN to Address Valid tCLCL - 4 ns
tAVIV Address to Valid Instruction In 5tCLCL - 50 ns
tPLAZ PSEN Low to Address Float 20 ns
tRLRH RD Pulse Width 6tCLCL ns
tWLWH WR Pulse Width 6tCLCL ns
tRLDV RD Low to Valid Data In 5tCLCL - 50 ns
tRHDX Data Hold after RD tCLCL + 20 ns
tRHDZ Data Float after RD 2tCLCL - 20 ns
tLLDV ALE Low to Valid Data In 8tCLCL - 50 ns
tAVDV Address to Valid Data In 9tCLCL - 50 ns
tLLWL ALE Low to RD or WR Low 3tCLCL - 24 3tCLCL ns
tAVWL Address to RD or WR Low 4tCLCL - 12 ns
tQVWX Data Valid to WR Transition 2tCLCL - 24 ns
tQVWH Data Valid to WR High 8tCLCL - 24 ns
tWHQX Data Hold after WR 2tCLCL - 24 ns
tRLAZ RD Low to Address Float 2tCLCL + 10 ns
tWHLH RD or WR High to ALE High tCLCL - 10 tCLCL + 20 ns
46
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
33. External Program Memory Read Cycle
34. External Data Memory Read Cycle
47
3286C MICRO 1/05
35. External Data Memory Write Cycle
36. External Clock Drive Waveforms
37. External Clock Drive
VCC = 2.7V to 5.5V
Symbol Parameter Min Max Units
1/tCLCL Oscillator Frequency 0 24 MHz
tCLCL Clock Period 41.6 ns
tCHCX High Time 12 ns
tCLCX Low Time 12 ns
tCLCH Rise Time 5ns
tCHCL Fall Time 5ns
48
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
38. Serial Port Timing: Shift Register Mode Test Conditions
The values in this table are valid for VCC = 2.7V to 5.5V and Load Capacitance = 80 pF.
Variable Oscillator
Symbol Parameter Min Max Units
tXLXL Serial Port Clock Cycle Time 12tCLCL -15 µs
tQVXH Output Data Setup to Clock Rising Edge 10tCLCL -15 ns
tXHQX Output Data Hold after Clock Rising Edge 2tCLCL -15 ns
tXHDX Input Data Hold after Clock Rising Edge tCLCL ns
tXHDV Input Data Valid to Clock Rising Edge 0 ns
39. Shift Register Mode Timing Waveforms
40. AC Testing Input/Output Waveforms(1)
Note: 1. AC Inputs during testing are driven at VCC - 0.5V for a logic 1 and 0.45V for a logic 0. Timing measurements are made at VIH
min. for a logic 1 and VIL max. for a logic 0.
41. Float Waveforms(1)
Note: 1. For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to
float when a 100 mV change from the loaded VOH/VOL level occurs.
49
3286C MICRO 1/05
42. ICC Test Condition, Active Mode, All Other Pins are Disconnected
VCC
ICC
VCC
RST
VCC
P0
EA
(NC) XTAL2
CLOCK SIGNAL
XTAL1
VSS
43. ICC Test Condition, Idle Mode, All Other Pins are Disconnected
VCC
ICC
VCC
RST
VCC
P0
EA
(NC) XTAL2
CLOCK SIGNAL
XTAL1
VSS
44. Clock Signal Waveform for ICC Tests in Active and Idle Modes,
tCLCH = tCHCL = 5 ns
VCC - 0.5V
0.7 VCC
tCHCX
0.2 VCC - 0.1V
tCLCH
0.45V
tCHCL tCHCX
tCLCL
45. ICC Test Condition, Power-down Mode, All Other Pins are Disconnected,
VCC = 2V to 5.5V
VCC
ICC
VCC
RST
VCC
P0
EA
(NC) XTAL2
XTAL1
VSS
50
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
46. ICC (Active Mode) Measurements
AT89S8253 I Active @ 25oC
CC
With Internal Clock Oscillator
x1 Mode
4.00
3.50
3.0V
3.00
4.0V
2.50
5.0V
2.00
1.50
1 2 3 4 5 6 7 8 9 10 11 12
Frequency (MHz)
AT89S8253 I Active @ 90oC
CC
With Internal Clock Oscillator
x1 Mode
4.00
3.50
3.0V
3.00
4.0V
2.50
5.0V
2.00
1.50
1 2 3 4 5 6 7 8 9 10 11 12
Frequency (MHz)
51
3286C MICRO 1/05
CC
I
Active (mA)
CC
I
Active (mA)
47. ICC (Idle Mode) Measurements
AT89S8253 I Idle vs. Frequency,
CC T = 25°C
With Internal Clock Oscillator
x1 Mode
3
2.5
2
Vcc=3V
1.5
Vcc=4V
1
Vcc=5v
0.5
0
0 5 10 15 20 25
Frequency (MHz)
48. ICC (Power Down Mode) Measurements
AT89S8253 ICC in Power-down
2.5
2
0 deg C
1.5
25 deg C
1
90 deg C
0.5
0
1 2 3 4 5 6 7
VCC (V)
52
AT89S8253 [Preliminary]
3286C MICRO 1/05
CC
I
(mA)
CC
I
Pwd (uA)
 AT89S8253 [Preliminary]
49. Ordering Information
49.1 Standard Package
Speed Power
(MHz) Supply Ordering Code Package Operation Range
AT89S8253-24AC 44A
AT89S8253-24JC 44J Commercial
2.7V to 5.5V
AT89S8253-24PC 40P6 (0°C to 70°C)
AT89S8253-24SC 42PS6
24
AT89S8253-24AI 44A
AT89S8253-24JI 44J Industrial
2.7V to 5.5V
AT89S8253-24PI 40P6 (-40°C to 85°C)
AT89S8253-24SI 42PS6
49.2 Green Package Option (Pb/Halide-free)
Speed Power
(MHz) Supply Ordering Code Package Operation Range
AT89S8253-24AU 44A
AT89S8253-24JU 44J Industrial
24 2.7V to 5.5V
AT89S8253-24PU 40P6 (-40°C to 85°C)
AT89S8253-24SU 42PS6
Package Type
44A 44-lead, Thin Plastic Gull Wing Quad Flat Package (TQFP)
44J 44-lead, Plastic J-leaded Chip Carrier (PLCC)
40P6 40-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
42PS6 42-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
53
3286C MICRO 1/05
50. Package Information
50.1 44A  TQFP
PIN 1
B
PIN 1 IDENTIFIER
E1 E
e
D1
D
C
0Ú~7Ú
A1 A2 A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A   1.20
A1 0.05  0.15
A2 0.95 1.00 1.05
D 11.75 12.00 12.25
D1 9.90 10.00 10.10 Note 2
E 11.75 12.00 12.25
Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB.
E1 9.90 10.00 10.10 Note 2
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
B 0.30  0.45
plastic body size dimensions including mold mismatch.
C 0.09  0.20
3. Lead coplanarity is 0.10 mm maximum.
L 0.45  0.75
e 0.80 TYP
10/5/2001
TITLE DRAWING NO. REV.
2325 Orchard Parkway
44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,
44A
R San Jose, CA 95131 B
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
54
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
50.2 44J  PLCC
1.14(0.045) X 45Ú
PIN NO. 1
1.14(0.045) X 45Ú
0.318(0.0125)
IDENTIFIER
0.191(0.0075)
D2/E2
E1 E B1
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45Ú MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A 4.191  4.572
A1 2.286  3.048
A2 0.508  
D 17.399  17.653
D1 16.510  16.662 Note 2
E 17.399  17.653
Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC.
E1 16.510  16.662 Note 2
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
D2/E2 14.986  16.002
and E1 include mold mismatch and are measured at the extreme
B 0.660  0.813
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum. B1 0.330  0.533
e 1.270 TYP
10/04/01
TITLE DRAWING NO. REV.
2325 Orchard Parkway
44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC)
44J B
R San Jose, CA 95131
55
3286C MICRO 1/05
50.3 40P6  PDIP
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
COMMON DIMENSIONS
(Unit of Measure = mm)
0º ~ 15º REF
C
SYMBOL MIN NOM MAX NOTE
A   4.826
eB
A1 0.381  
D 52.070  52.578 Note 2
E 15.240  15.875
E1 13.462  13.970 Note 2
B 0.356  0.559
B1 1.041  1.651
Notes: 1. This package conforms to JEDEC reference MS-011, Variation AC.
2. Dimensions D and E1 do not include mold Flash or Protrusion. L 3.048  3.556
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
C 0.203  0.381
eB 15.494  17.526
e 2.540 TYP
09/28/01
TITLE DRAWING NO. REV.
2325 Orchard Parkway
40P6, 40-lead (0.600"/15.24 mm Wide) Plastic Dual
40P6 B
R San Jose, CA 95131
Inline Package (PDIP)
56
AT89S8253 [Preliminary]
3286C MICRO 1/05
 AT89S8253 [Preliminary]
50.4 42PS6  PDIP
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
COMMON DIMENSIONS
(Unit of Measure = mm)
0º ~ 15º REF
C
SYMBOL MIN NOM MAX NOTE
A   4.83
eB
A1 0.51  
D 36.70  36.96 Note 2
E 15.24  15.88
E1 13.46  13.97 Note 2
B 0.38  0.56
B1 0.76  1.27
Notes: 1. This package conforms to JEDEC reference MS-011, Variation AC.
2. Dimensions D and E1 do not include mold Flash or Protrusion. L 3.05  3.43
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
C 0.20  0.30
eB   18.55
e 1.78 TYP
11/6/03
TITLE DRAWING NO. REV.
2325 Orchard Parkway
42PS6, 42-lead (0.600"/15.24 mm Wide) Plastic Dual
42PS6 A
R San Jose, CA 95131
Inline Package (PDIP)
57
3286C MICRO 1/05
Atmel Corporation Atmel Operations
2325 Orchard Parkway
Memory RF/Automotive
San Jose, CA 95131, USA
2325 Orchard Parkway Theresienstrasse 2
Tel: 1(408) 441-0311
San Jose, CA 95131, USA Postfach 3535
Fax: 1(408) 487-2600
Tel: 1(408) 441-0311 74025 Heilbronn, Germany
Fax: 1(408) 436-4314 Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Regional Headquarters
Microcontrollers
2325 Orchard Parkway
1150 East Cheyenne Mtn. Blvd.
Europe
San Jose, CA 95131, USA
Colorado Springs, CO 80906, USA
Atmel Sarl
Tel: 1(408) 441-0311
Tel: 1(719) 576-3300
Route des Arsenaux 41
Fax: 1(408) 436-4314
Fax: 1(719) 540-1759
Case Postale 80
CH-1705 Fribourg
La Chantrerie Biometrics/Imaging/Hi-Rel MPU/
Switzerland
BP 70602
High Speed Converters/RF Datacom
Tel: (41) 26-426-5555
44306 Nantes Cedex 3, France
Avenue de Rochepleine
Fax: (41) 26-426-5500
Tel: (33) 2-40-18-18-18
BP 123
Fax: (33) 2-40-18-19-60
38521 Saint-Egreve Cedex, France
Asia
Tel: (33) 4-76-58-30-00
Room 1219
ASIC/ASSP/Smart Cards
Fax: (33) 4-76-58-34-80
Chinachem Golden Plaza
Zone Industrielle
77 Mody Road Tsimshatsui
13106 Rousset Cedex, France
East Kowloon
Tel: (33) 4-42-53-60-00
Hong Kong
Fax: (33) 4-42-53-60-01
Tel: (852) 2721-9778
Fax: (852) 2722-1369
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Japan
Tel: 1(719) 576-3300
9F, Tonetsu Shinkawa Bldg.
Fax: 1(719) 540-1759
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Scottish Enterprise Technology Park
Japan
Maxwell Building
Tel: (81) 3-3523-3551
East Kilbride G75 0QR, Scotland
Fax: (81) 3-3523-7581
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© Atmel Corporation 2005. All rights reserved. Atmel®, logo and combinations thereof, and others, are registered trademarks, and
Everywhere You AreSM and others are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be
trademarks of others.
Printed on recycled paper.
3286C MICRO 1/05 xM


Wyszukiwarka

Podobne podstrony:
datasheet tda 2030
DatasheetTabbedPane
datasheet pcip3
1675 LambdaUnite DataSheet
datasheet 4
datasheet
datasheet (2)
Datasheet BlueSolar charge controller MPPT 75 50 & MPPT 100 50 EN
TMG0165 datasheet
datasheet ap44
datasheet

więcej podobnych podstron