{
MILL=T
LATHE=F
SIMPLE_ROT_POS=F
ROTARY_MILL=F
ADV_MILL=T
SUBS=T
MILLTURN_Y-AXIS=F
METRIC=F
}
{Change Comments ***********************************************************}
{5/15/98,
Updated: Fanuc 6M (PW) C001.15
Created: Fanuc 6M [PW] C001.16
For: Gibbs & Associates
Versions: Catalyst v4.23.13(mac)/ComPost2 1.1b3
Corrected support for Linear ChangeCS.
Linear ChangeCS covers Multiple CSGroups in One Plane.
Post does not output CSWFOComments, G52Comments or G52Stuff for this situation.
IF AAxisAvail? OR BAxisAvail? does not automatically support this.
Deleted IF AAxisAvail? OR BAxisAvail? at G52Stuff, DoCSComment and DoCSWFOComment.
Post retracts Tool at SameTool for this situation.
Retraction is only necessary for AChange OR BChange situations.
Changed ChangeCS? to AChange? OR BChange at SameToolOp1.
Changed ChangeCS? to AChange? OR BChange at SameToolOp3.
Simplified ClearCSOffset occurance.
ClearCSOffset occurs at 5 different places, including at the output of CSComments.
Discovered that CheckPass is a good place for all situations.
Deleted ClearCSOffset at CSComments.
Caused simplification of Procedure.
Deleted ClearCSOffset at CSG52, DoCSWFOComment, OpenMP and SubCSMP Procedures.
Added ClearCSOffset at CheckPass.
Additional modifications.
Moved IF FirstOperation? OR NewTool? OR ChangeCS? Boolean from CSG52 to G52Stuff.
Moved DoSubComment Procedure to before DoOpComments Procedure.
To keep CSStuff together.
Moved call to CSComments Procedure to inside IF UseComments? Boolean at DoOpComments.
To suppress when Comments are turned off.
Added AbsValueC, IncValueC and AbsOrIncC Procedures.
Simplifies readability of Prog.
Reduces redundancy of output.
Allows us to return to earlier versions
Improves upon earlier problem with incremental output of ShiftPC command at CloseMP while
allowing us to return to .85 OfstOff blocks.
AbsValueC called from AbsOrIncC.
IncValueC called from AbsOrIncC, DoAbsOrInc and DoDrillAbsOrInc.
IncValueC called for OfstOff Blocks at NewToolOp1, two places at SameToolOp1 and DoAbsOrInc.
AbsOrIncC called for ShiftPC Block at CloseMP.
AbsOrIncC called from DoAbsOrInc, DoDrillAbsOrInc and RestoreAbsOrInc.
AbsOrIncC called for Home Block at NewToolOp2.
AbsOrIncC called for FirstHome Block at End2.
Added CRCOffC at AutoCycCutSub2.
Corrects unique situation in ZonlyRepAutoCycle where one Operation is CRCLeft and LastFeat
is an ArcFeat followed by another Operation that is CRCRight.
CRCOffC did not get output at end of CRCLeft Operation and CRCOnC did not get output at start
of CRCRight Operation.
Oddly, CRCOnC only outputs if CRCOffC has been output, not if CRCSide changes.
Moved call to InitOp Procedure to top level at end of Prog.
Personal Preference.
6/18/98
Changed to Lowercase Procedure Names.
Added comments to all SetFlag, SetFlagF and IF Flag statements.
Added Flag(6) to switch from B-Style to C-Style at progStart.
TRUE = B-Style Output, FALSE = C-Style Output.
Added Flag(7) to switch from local coordinates to uncompensated coordinates at progStart.
TRUE = Local WFO Coordinates, FALSE = D-Style Output.
Added pertinent comments at progStart.
Added IF Equal? NumOfCS# Num#('1') at progStart.
This is a standard 3 Axis - Output M-Style.
Changed Seq to SeqC at autoCycCutSub1.
Added CRCOffC to AutoCycle ZCP3C at end of IF Milling?
Moved CRCOffC to before FeedC and RapidC for ZCP3C at end of IF Milling?
To stay consistant with CRCOnC/CRCOffC Rapid/Feed/CWArc/CCWArc throughout Prog.
Changed literal 'G80' to DrillOff at end of IF Drilling.
Changed literal 'G80' to DrillOff at firstOp1 and newToolOp3.
To allow for change in FORM without having to recompile.
Changed SpeedC to Speed at for LAST ProgStop condition at sameToolOp3.
6/30/98
Deleted Gibbs System XYRepeat support.
Virtual only support ZShiftOnly Repeats.
Rewrote OpGuts Procedure.
Limited Milling Repeats to ZShiftOnly at IF Milling.
Deleted Drilling Repeats at IF Drilling.
Rewrote PostScript instructions at progStart.
7/22/98
Reverted back to Gibbs System XYRepeat support.
IF setup correctly, Virtual will support XShift and/or YShift Repeats for both Contour and
Patterns.
Rules for correct setup (as best as I understand at the moment).
Geometry CSGroup must be oriented to a plane that intersects CS#1 in a perpendicular direction.
Example, XZPlane and YZPlane, and any oriented rotation of either Plane around the XYPlane.
Any change in the ZPitch of the Origin will cause ZShiftOnly Repeat Operation.
Set Desired ZStep so that Operation will result in multiple passes.
NOTE: If correctly setup, ZStep would be misleading.
Step will be in line with depth axis of CSGroup.
Restored related code to OpGuts Procedure.
ZShiftOnly Contour Operations remain Full SepSub.
Any customer requesting G92 Style will require copying code from archives.
Deleted Deceleration from ToolPath LineFeat and ArcFeat.
There are plans to support this in the future through the use of Construction Tools in the
Virtual Process.
9/1/98
Added forced FeedRate for RI-RO Milling Operations.
When a RI-RO Operation follows either a FI-RO or RI-RO Operation, and both contain the same
FeedRate values, the second Operation does not get a FeedRate output due to the conditional
FeedRateC command. A problem arises for MultipleParts - OneToolAllParts - ExitClearancePlane
Programs when both Operations use different Tools, and a third Operation uses the SameTool as the
second Operation, but has a different FeedRate value. The result is that when the Program moves
to machine the additional parts with the second Operation at the FeedRate value of the third
Operation. It is safer to just force the FeedRate in the second Operation.
Added FORMAT#7, '#' at Prog Numeric Format Definitions.
Added RapidF# to Format#7 at Prog Numeric Format Definitions.
RapidF# equals zero and this FORMAT allows for nothing to be output.
Added RapidF# at entryMove Procedure.
Added IF FirstOperation? OR NewTool? condition two places at entryMove Procedure.
To force FeedEnt and RapidF#.
SameTool condition outputs conditional FeedEntC.
Added IF NOT AbsoluteMoves? Boolean and SetSRXYtoEP command to zonlyRep.
This fixes problem with Incremental output of move back to StrtPos for additional passes.
Deleted UseSeparateSubCalls at ProgStart Procedure.
Deleted SetMaxSeparateSubCalls('50') at ProgStart Procedure.
Moved IF ToolChangeAtHome? Boolean and SetHome command from InitOp to FirstOp1.
Personal preference for moving Procedure call to top level at end of Prog on 5/15/98 was to
reduce it to one occurance, consistant with LongHand version where it works. However, it was
reported that the IF ToolChangeAtHome? Boolean and SetHome command occuring outside of
EachOp/NextOp loop was causing Windows version to crash. Duplicating problem required having a
part file open and a post processor loaded, and then opening a new part with one of the beta
masters. I was not able to duplicate this on the Macintosh.
Changed name of doCSG52Ops Procedure to doWFOOps.
Changed call of same two places at openMP.
Name was misleading because Procedure is also called for standard MultipleParts output, not just
G52Style and contents are identicle to M001.
9/24/98
Added Post Header Comment at top.
Added missing END command at entryMove.
Changed IncValue to incValueC at autoCycCutSub1.
Changed AbsOrInc to absOrIncC at autoCycCutSub2.
Changed AbsOrInc to absOrIncC at g92Sub.
Added support of Incremental Output for SepSubs.
When user selects Incremental Output, SepSubZMoves are incorrect.
Added doSepSubZMoves Procedure.
Contains code for ZPosMoves from zonlyRepAutoCycle and zonlyRep Procedures.
Outputs Incremental ZExitMove for Exit/Entry.
AutoCycles Retract to ZCP2.
Non-AutoCycles Retract to ZCP3.
Added setSepSubZ Procedure.
Updates Status Register to final ZInPos for FeedEntry.
Modified zonlyRepAutoCycle Procedure.
Modified zonlyRep Procedure.
Expanded Advanced Milling Flags for easier developing.
Changed Flag(7) to be dedicated to D-Style Output only.
Added Flag(8) for Toggle between D-Style and G52-Style Output.
5 possible combinations:
BStyle/G52Style Flag(6) FlagF(7) FlagF(8)
BStyle/DStyle Flag(6) FlagF(7) Flag(8)
CStyle/G52Style FlagF(6) FlagF(7) FlagF(8)
CStyle/DStyle FlagF(6) FlagF(7) Flag(8)
DStyle FlagF(6) Flag(7) Flag(8)
10/1/98
Versions: Virtual 4.29.75(Mac)/ComPost2 1.7b10 (Mac)
Versions: Virtual 4.29.75(Win)/ComPost2 1.7b10 (Win)
Corrected old problem with Incorrect Status Register XYPos at end of Pattern AutoCycle Operation.
Problem is caused because Status Register is left in SetPass1 [ Contouring ] Mode and does not compensate
for SetPass2 [ PointFeat Position ] Mode Coordinates
Correction fixes known problems with Full Incremental Output.
Correction also fixes known problems with MultipleParts EquallySpacedOffsets ShiftPC and UnshftPC commands.
Added TrackXNO# to FORMAT#4 at Prog Numeric Format Definitions.
Added TrackYNO# to FORMAT#4 at Prog Numeric Format Definitions.
Added getACEPXY Procedure.
Called from ToolPath PointFeat.
Stores uncompensated LastFeat SPX# to Var(1).
Stores uncompensated LastFeat SPY# to Var(2).
Added setSRXYtoACEP Procedure.
Called at end of OpGuts IF Milling.
Adds SetPass1 LastFeat SPXY# to uncompensated SetPass2 LastFeat SPXY#.
Added Var(1) for storage of XPosition at progStart Procedure.
Added Var(2) for storage of YPosition at progStart Procedure.
DWB}
{3/22/99,
Initial : Fanuc 6M [PW] C001.16
Created: Mit 520AM Akira [PF] CQ46.16
Customer: P & F Machine, Chris Mello 209/667-2515
ComPost2: v1.7b15
Changes to "Form":
1. Under Arcs, changed I-J Max Arc Radius to 0.000
2. Under Spindle and Coolant, changed Spindle Off Number to 19
Changes to "Prog":
1. Changed firstOp1, 2, & 3 to match MU61 output.
2. Changed newToolOp1, 2, 3, 4, & 5 to match MU61 output.
3. Changed sameToolOp1 & 3 to match MU61 output.
4. Changed end1, 2, & 3 to match MU61 output.
5. Added doClampOn sub to output M25.
6. Added doClampOff sub to output M26.
7. Under formatArc sub, removed C from ArcRC.
8. Changed feedrate to FeedTapIPR# and added ',R1' to RigidTap.
9. Added FORMAT for FeedTapIPR#.
JHE}
{Prog Numeric Format Definitions *****************************}
#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*#####.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(TrackXNO#,4)
FORMAT(TrackYNO#,4)
FORMAT(TrackZNO#,4)
FORMAT(FeedTapIPR#,4) {Added - JHE}
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(CSSubID#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)
{Prog Subroutines **************************************}
restoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
cSPartNum#:
ADD# CS# MUL# NumOfCS# SUB# PartNum# Num#('1')
RETURN
cSWFO:
'G' ADD# cSPartNum# Num#('53')
RETURN
wFO:
'G' ADD# PartNum# Num#('53')
RETURN
wFOStuff:
IF Flag?('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF NOT SameTool?
IF WFOCS?
cSWFO
ELSE
wFO
END
ELSE
IF WFOCS?
IF ChangeCS?
IF MultipleParts?
{MP ChangeCS is handled in subCSMP and closeMP}
ELSE
cSWFO
END
END
END
END
END
SetFlagF('2') { Do not output WFO second time wFOStuff is called for MP-WFO-OTAP-ECP }
RETURN
cSG52:
SeqC 'G52X' CSOffsetX# 'Y' CSOffsetY# 'Z' CSOffsetZ# EOL
RETURN
g52Stuff:
IF NOT Flag?('7') AND NOT WFOCS?
IF FirstOperation? OR NewTool? OR ChangeCS?
IF MultipleParts?
IF WorkFixtureOffsets?
cSG52
END
ELSE
cSG52
END
END
END
RETURN
doCSComment:
'( CS#' CS# ' - ' CSComment$ ' )' EOL
RETURN
doCSWFOComment:
IF FirstOperation? OR NewTool? OR ChangeCS?
'( ' cSWFO ' = X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ#
IF Flag?('6') { TRUE = B-Style Output, FALSE = C-Style Output }
IF AAxisAvail?
' A' CSOffsetA#
END
IF BAxisAvail?
' B' CSOffsetB#
END
END
' )' EOL
END
RETURN
cSComments:
doCSComment
IF WFOCS? AND NOT MultipleParts?
doCSWFOComment
END
RETURN
doSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN
doOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
restoreScale
cSComments
END
RETURN
doClampOn: {Added this sub - JHE}
IF AAxisAvail? OR BAxisAvail?
'M25'
END
RETURN
doClampOff: {Added this sub - JHE}
IF AAxisAvail? OR BAxisAvail?
'M26'
END
RETURN
cSAngleA:
IF AAxisAvail?
IF Flag?('6') AND WFOCS? { TRUE = B-Style Output, FALSE = C-Style Output }
'A0.'
ELSE
'A' CSOffsetA#
END
END
RETURN
cSAngleAC:
IF AChange?
cSAngleA
END
RETURN
cSAngleB:
IF BAxisAvail?
IF Flag?('6') AND WFOCS? { TRUE = B-Style Output, FALSE = C-Style Output }
'B0.'
ELSE
'B' CSOffsetB#
END
END
RETURN
cSAngleBC:
IF BChange?
cSAngleB
END
RETURN
pSInit:
NewWFOF
FourthCWF
FourthCCWF
FifthCWF
FifthCCWF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN
pSStuff:
RETURN
doPostScript:
pSInit
EachPS
SeqC PostScript EOL
pSStuff
NextPS
RETURN
doEndOpPS:
pSInit
EachEOPS
SeqC EndOpPS EOL
pSStuff
NextPS
RETURN
entryMove:
IF FeedEntry?
SeqC Feed ZIn
IF FirstOperation? OR NewTool?
FeedEnt
ELSE
FeedEntC
END
EOL
ELSE
SeqC RapidC ZIn EOL
IF FirstOperation? OR NewTool?
RapidF# { Forces FeedRate }
END
END
RETURN
startSub:
OpenSub
SubID EOL
doSubComment
RETURN
subWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN
stdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
startSub
RETURN
finishSub1: {part 1}
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN
finishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN
absValueC:
IF NOT AbsValue?
AbsValue
END
RETURN
incValueC:
IF AbsValue?
IncValue
END
RETURN
absOrIncC:
IF AbsoluteMoves?
absValueC
ELSE
incValueC
END
RETURN
toggleIncDecWFO:
IF Flag?('3') { Incrementing WFOs in effect }
SetFlagF('3')
ELSE { Decrementing WFOs in effect }
SetFlag('3')
END
RETURN
doWFOOps:
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
ELSE
SeqC SetWFO EOL
END
SeqC SubCall CallLab RepLab OnePart EOL
RETURN
openMP:
NewProg
IF WorkFixtureOffsets?
IF WFOCS?
startSub
SaveCSProg
SaveCSOpStart
ELSE
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
END
IF Flag?('3') { Incrementing WFOs in effect }
NewWFO
EachWFO {simple eachPart}
doWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE { Decrementing WFOs in effect }
LastWFO
EachWFO {simple eachPart}
doWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4') { This post supports IncWFO/DecWFO }
toggleIncDecWFO
END
startSub
END
ELSE
SeqC SubCall CallLab RepLab Parts EOL
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
startSub
END
RETURN
doCSWFOOps:
EachCSOp
doCSWFOComment
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
ELSE
SeqC cSWFO EOL
END
SeqC SubCall CallLabB CSSubID# RepLab OnePart EOL
NextCSOp
RETURN
closeMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
IF WFOCS?
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
END
IF Flag?('3') { Incrementing WFOs in effect }
NewWFO
EachWFO {simple eachPart}
doCSWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE { Decrementing WFOs in effect }
LastWFO
EachWFO {simple eachPart}
doCSWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4') { This post supports IncWFO/DecWFO }
toggleIncDecWFO
END
END
ELSE
SeqC absOrIncC EOL
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN
subCSMP:
IF WFOCS?
IF ChangeCS?
SeqC EndSub EOL
CloseSub
NewProg
startSub
SaveCSProg
END
END
RETURN
doAbsOrInc:
IF Flag?('1') { Milling ZShiftOnly SepSubs/DrillSubs activated }
IF ZMove?
incValueC
ELSE
absOrIncC
END
END
RETURN
doDrillAbsOrInc:
IF Flag?('1') { DrillSubs activated }
IF SPZMove?
incValueC
ELSE
absOrIncC
END
END
RETURN
restoreAbsOrInc:
IF Flag?('1') { Milling ZShiftOnly SepSubs/DrillSubs activated }
SeqC absOrIncC EOL
END
RETURN
formatArc:
doAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcR {Removed C - JHE}
END
RETURN
ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN
ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN
getACEPXY:
SetACSPCompF
Save# Num#('1') SPX# { Status Register Variable for X Axis }
Save# Num#('2') SPY# { Status Register Variable for Y Axis }
SetACSPComp
RETURN
setSRXYtoACEP:
SetPass1
SetSRXYtoEP
LoadFeat Num#('0') Num#('0') Num#('0')
TrackXNO# ADD# Recall# Num#('1') SPX# { Status Register Variable for X Axis }
TrackYNO# ADD# Recall# Num#('2') SPY# { Status Register Variable for Y Axis }
RETURN
toolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
IF LastFeat?
getACEPXY
END
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC doDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC doAbsOrInc ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
SeqC doAbsOrInc ckCRC FeedC MoveXYZC FeedRateC ckCRCNum EOL
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
SeqC formatArc ArcFeedC EOL
NEXTQuadrant
END
END
END
END
NEXTFeat
restoreAbsOrInc
RETURN
autoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
startSub
SetSRXYtoSP
SeqC incValueC EOL
RETURN
autoCycCutSub2: {part 2}
toolPath
SeqC absOrIncC CRCOffC
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN
autoCycPat:
SetPass2 {position pattern}
toolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN
milling:
IF AutoCycle?
NewProg
autoCycCutSub1
entryMove
autoCycCutSub2
autoCycPat
ELSE
entryMove
toolPath
END
RETURN
g92Sub:
subWarning
stdSub
SeqC absOrIncC Connect StrtPos EOL
milling
finishSub1
finishSubG92
RETURN
doSepSubZMoves:
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusInc EOL
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FirstCycle? AND AutoCycle?
Rapid
END
SeqC RapidC ZInPlusInc EOL
END
END
SeqC SubCall CallLab EOL
IF NOT FeedConnect? AND NOT AbsValue?
TrackZNO# ZCP2PlusInc#
SeqC ZCP2C EOL
IF NOT AutoCycle?
TrackZNO# ClearancePlane3#
END
END
RETURN
setSepSubZ:
TrackZNO# ADD# FIRST SPZ# MUL# RepsLess1# RepeatZ#
RETURN
zonlyRepAutoCycle:
autoCycPat {write pattern moves and main calls}
startSub
NewProg
EachCycle
SetSRXYtoEP
IF NOT FirstCycle?
Connect
IF SPXMove? OR SPYMove?
SeqC incValueC StrtPosC EOL
absOrIncC
END
END
SetStatusOn
doSepSubZMoves
SetStatusOff
NextCycle
SetStatusOn
autoCycCutSub1 {build element sub}
TrackZNO# FIRST SPZ#
autoCycCutSub2
IF FeedConnect?
IF NOT AbsValue?
setSepSubZ
END
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN
zonlyRep:
EachCycle
SetSRXYtoEP
IF NOT FirstCycle?
Connect
IF SPXMove? OR SPYMove?
SeqC StrtPosC EOL
END
END
doSepSubZMoves
NextCycle
startSub
TrackZNO# FIRST SPZ#
toolPath
finishSub1
SeqC EndSub EOL
CloseSub
IF FeedConnect? AND NOT AbsValue?
setSepSubZ
END
RETURN
checkPass: {use the correct StrtPos}
IF AutoCycle?
SetPass2
ELSE
SetPass1
END
IF NOT Flag?('7')
ClearCSOffset
END
RETURN
skipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN
setDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
opGuts:
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
zonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
SetFlag('1') { Milling ZShiftOnly SepSubs activated }
zonlyRep
SetFlagF('1') { Milling ZShiftOnly SepSubs deactivated }
END {end Auto Cycle IF}
ELSE {not Z only}
g92Sub
END {end Z only IF}
ELSE {no repeat OPs}
milling
END
IF AutoCycle?
SeqC CRCOffC ZCP3C EOL
setSRXYtoACEP
ELSE
IF FIFO?
SeqC CRCOffC FeedC ZCP3C FeedEntC EOL
ELSE
SeqC CRCOffC RapidC ZCP3C EOL
END
END
ELSE
IF Drilling?
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF RigidTap?
'F' FeedTapIPR#('1') ',R1' EOL {Added - JHE}
ELSE
FeedEnt EOL
END
IF CallMasterOp?
SeqC SubCall CallLabB CallMasterNum# EOL
skipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') { DrillSubs activated }
NewMasterProg
SeqC SubCall CallLab EOL
startSub
toolPath
SeqC EndSub EOL
CloseSub
SetFlagF('1') { DrillSubs deactivated }
ELSE
toolPath
END
END
setDrillEndOpZ
SeqC DrillOff Rapid ZCP3 EOL
END
END
RETURN
progStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('12700')
ELSE
SetMaxFeed('500')
END
Save# Num#('1') Num#('0') { Status Register Variable for X Axis }
Save# Num#('2') Num#('0') { Status Register Variable for Y Axis }
Save# Num#('3') Num#('0') { Status Register Variable for Z Axis }
SetFlagF('1') { Milling ZShiftOnly SepSubs/DrillSubs deactivated }
SetFlagF('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
SetFlag('3') { Incrementing WFOs in effect }
SetFlag('4') { This post supports IncWFO/DecWFO }
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
SetFlagF('6') { TRUE = B-Style Output, FALSE = C-Style Output }
SetFlagF('7') { TRUE = D-Style Output }
SetFlag('8') { TRUE = D-Style Output, FALSE = Local G52-WFO Coordinates }
IF PSComment? AND UseComments?
'Utility Data:' EOL
' At Op Start: All literals and commands will appear at the beginning of the operation.' EOL
' At Op End: All literals and commands will appear at the end of the operation.' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
END
IF NOT Flag?('7')
IF Equal? NumOfCS# Num#('1') { 3 Axis Part - Output M-Style }
SetFlag('7')
ELSE
IF MultipleParts?
IF WorkFixtureOffsets?
IF LTEqual? MUL# Parts# NumOfCS# Num#('6')
SetWFOCS { use WFO for CS changes }
ELSE
IF Flag?('8')
SetFlag('7')
END
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of parts [ ' Parts# ' ] times CSs [ ' NumOfCS# ' ] )' EOL
'( exceeds the machine limit. Switching to '
IF Flag?('7')
'non'
ELSE
'G52'
END
'-wfo style output. )' EOL
END
END
ELSE
SetFlag('7')
END
ELSE
IF LTEqual? NumOfCS# Num#('6') {****}
SetWFOCS { use WFO for CS changes }
ELSE
IF Flag?('8')
SetFlag('7')
END
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of CSs [ ' NumOfCS# ' ] exceeds the machine limit. )' EOL
'( Switching to '
IF Flag?('7')
'non'
ELSE
'G52'
END
'-wfo style output. )' EOL
END
END
END
END
END
RETURN
initOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
restoreScale
RETURN
firstOp1:
IF ToolChangeAtHome?
SetHome
END
Seq Rapid Plane CRCOff 'G49' DrillOff incValue OfstOff EOL {Added G49 & incValue OfstOff - JHE}
SeqC OpToolID ToolChng EOL
doOpComments
doPostScript
RETURN
firstOp2:
SeqC wFOStuff EOL
g52Stuff
SeqC doClampOff EOL {Added this line - JHE}
checkPass
SeqC AbsOrInc Rapid StrtPos cSAngleA cSAngleB
IF Drilling? AND RigidTap? {Added this boolean - JHE}
Speed EOL
ELSE
Speed SpinOn EOL
END
SeqC doClampOn EOL {Added this line - JHE}
RETURN
firstOp3:
SeqC OfstOn CoolOn PreTool EOL {Added PreTool - JHE}
RETURN
newToolOp1:
SeqC CoolOff EOL
SeqC 'G49' incValueC OfstOff SpinOff EOL {Added G49 & SpinOff - JHE}
RETURN
newToolOp2:
doEndOpPS
IF ToolChangeAtHome?
SeqC absOrIncC RapidC Home EOL {Removed SpinOff - JHE}
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN
newToolOp3: {Start new Operation}
Seq Rapid Plane CRCOff 'G49' DrillOff incValue OfstOff EOL {Added G49 & incValue OfstOff - JHE}
SeqC OpToolID ToolChng EOL
doOpComments
doPostScript
RETURN
newToolOp4:
SeqC wFOStuff EOL
g52Stuff
SeqC doClampOff EOL {Added this line - JHE}
checkPass
SeqC AbsOrInc Rapid StrtPos cSAngleA cSAngleB
IF Drilling? AND RigidTap? {Added this boolean - JHE}
Speed EOL
ELSE
Speed SpinOn EOL
END
SeqC doClampOn EOL {Added this line - JHE}
RETURN
newToolOp5:
SeqC OfstOn CoolOn PreTool EOL {Added PreTool - JHE}
RETURN
sameToolOp1:
doEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC 'G49' incValueC OfstOff SpinOff EOL {Added G49 & SpinOff - JHE}
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset? OR AChange? OR BChange?
SeqC 'G49' incValueC OfstOff EOL {Added G49 - JHE}
END
END
RETURN
sameToolOp2: {Start new Operation}
doOpComments
doPostScript
checkPass
RETURN
sameToolOp3: {Start new Operation}
SeqC wFOStuff EOL
g52Stuff
IF LAST ProgStop?
SeqC doClampOff EOL {Added this line - JHE}
SeqC PlaneC AbsOrInc Rapid StrtPos cSAngleA cSAngleB
IF Drilling? AND RigidTap? {Added this boolean - JHE}
Speed EOL
ELSE
Speed SpinOn EOL
END
SeqC doClampOn EOL {Added this line - JHE}
SeqC OfstOn CoolOn EOL
ELSE
IF AChange? OR BChange?
SeqC doClampOff EOL {Added this line - JHE}
END
SeqC PlaneC AbsOrInc Rapid StrtPos cSAngleAC cSAngleBC SpeedC EOL
IF AChange? OR BChange?
SeqC doClampOn EOL {Added this line - JHE}
END
IF NewToolOffset? OR AChange? OR BChange?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN
end1:
SeqC CoolOff EOL
SeqC 'G49' incValueC OfstOff SpinOff EOL {Added G49 & SpinOff - JHE}
RETURN
end2:
doEndOpPS
IF ToolChangeAtHome?
SeqC absOrIncC RapidC Home EOL
END
IF AAxisAvail? OR BAxisAvail? {Added these 2 lines - JHE}
SeqC doClampOff EOL
SeqC absOrIncC 'A0.' EOL
END
IF ProgStop?
SeqC 'M0' EOL
END
RETURN
end3:
SeqC absOrIncC 'G53X-12.Y0.' EOL {Added this line - JHE}
SeqC UnTool ToolChng EOL {Added this line - JHE}
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN
mPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
IF FirstOperation?
openMP
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2 {to tool change, CS problem}
subCSMP
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
end2
closeMP
end3
RETURN
mP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
IF FirstOperation?
firstOp1
openMP
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
closeMP
newToolOp2 {to tool change, CS problem}
newToolOp3
openMP
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
closeMP
end2
end3
RETURN
mP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
openMP
firstOp2 {need StrtPos in Sub}
ELSE
IF NewTool?
closeMP
newToolOp1
newToolOp2 {to tool change, CS problem}
newToolOp3
newToolOp4
newToolOp5
openMP
newToolOp4 {need StrtPos in Sub}
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
closeMP
end1
end2
end3
RETURN
noMPs: {no multiple parts}
EachOp {Start of post processing}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
end2
end3
RETURN
{Start of executable Prog, Top Level ****}
progStart {setup and initializations}
initOp
IF MultipleParts?
IF AllToolsOnePart?
mPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
mP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
mP1ToollAllPXcp
END
END
ELSE
noMPs
END
Wyszukiwarka
Podobne podstrony:
Mit 520AM Comet [RM] MZ18 89Mit 520AM Comet [AM] NMT10 16mMit 520AM Comet [RM] MZ18 89mMit 520AM Comet [ABB] CU61 12Mit 520A AS [RH] MT34 89Mit 520AM [ZE] MU85 89Mit Meldas 300 [SM] MT99 16 1Mit Meldas 520M [SP] MT48 16Fanuc 16M Mit [JPL] DQ14 16Mit Meldas 300 [SM] NMQ41 16 1Schalter ICs mit einstellbarer Strombegrenzungwięcej podobnych podstron