{Change Comments ***********************************************************}
{3/23/90, Updated: Fanuc 10T MS [+G54] L023.53 to .69.3 format, JR}
{7/24/90, Added InitProg globally to posts with this remark, DWB}
{9/17/90
Copied & modified: Fanuc 10T MS [+G54] L023.70
For: Gibbs & Associates
Machine: Mori Seiki
Control: Fanuc 10T
Updated to Version 3.2 per Fanuc 10T MS [-] L001.71.2 Format.
DWB}
{10/2/90, Added StockOff globally at FirstOperation, DWB}
{3/28/91
Modified: Fanuc 10T MS [+G54] L023.71.3
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 10T MS [-] L001.80 Format.
All normal Fanuc Canned Cycles are supported.
Changed Preset from G50 to G54 in Form.
G54 is a WFO. Used seperate G50 line for MaxRPM only.
Identicle modification made to Fanuc 10T (Anzon) L076.52 on 9/20/88
DWB}
{08/05/91
Updated: Fanuc 10T MS [+G54] L023.80
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.82 Format.
Kim Michelman}
{8/6/96,
Initial: Fanuc 10T MS [+G54] L023.82
Created: Fanuc 10T MS [+G54] L023.85
Updated to .85 format, MPK}
{8/7/96,
Initial: Fanuc 10T MS [+G54] L023.85
Created: Fanuc 10T MS [+G54] Lxxx.85
For: Pellco
Added hard coded bat pull routine to the beginning of output
Changed G4 dwell to use U label instead of P and output in Seconds instead of milliseconds
Moved Tool ID and offset from AppMove to G54 preset line in FirstOperation and in NewTool
Deleted X0Y0 from G54 lines
Eliminated saftey G97 output when using CSS
Deleted all literal dwells from tapping cycle
moved info for reversing the spindle for tapping into Linefeat in order to output properly
Changed label for thread lead when threading to F
Deleted CutMethod from canned threading cycle
Added literal 'M89' and '/M99P1' to program end.
Added 'Åš2' after barfeeder to ensure that N1 will not be output anwhere except the bar feed operation so that M99P1 command
always work
MPK}
{8/19/96,
Intial: Fanuc 10T MS [+G54PM] L498.85
Created: Fanuc 10T MS [+G54PM] L498.85.1
Deleted redundant G96 line at beginning of common point
added LatheOffset to OpToolID in NewTool
Made seqence numbers at tool changes conditional
Moved OpToolID and latheOffst to beginnig of line in FirstOperation and NewTool
Added CoolOn after Preset line in NewTool and FirstOperation
Changed IDApproachSP and ODApproachSP to not output G1 line when using Thread canned cycle
MPK}
{10/23/96,
Initial: Fanuc 10T MS [+G54PM] L498.85.1
Created: Fanuc 10T MS [+G54PM] L498.85.2
Formatted Tag#,
Changed StrtPos after RoughContuor cycle call to StrtPosC,
MPK}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.0###;0.0'
#3 = '########;0'
#4 = '###^##0'
#5 = '#.######;0.'
#6 = '###0'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Dwell#,2)
FORMAT(Program#,3) {.72}
FORMAT(Operation#,3) {.72}
FORMAT(Tool#,3) {.72}
FORMAT(FeedIPR#,5)
FORMAT(CalcEPRPM#,6)
FORMAT(Tag#,6)
{Prog Subroutines **********************************************************}
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
END
RETURN
PSInit: {reset flags from last Op, .70}
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN
StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN
ODApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
IF Threading? AND CannedCycle?
ELSE
SeqLabC Feed StockOnNoCan XSPC FeedRate EOL
END
RETURN
IDApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL { for SameTool ApproachID }
SeqLabC Feed StockOnNoCan XSPC FeedRate EOL
IF Threading? AND CannedCycle?
ELSE
SeqLabC Feed StockOnNoCan XSPC FeedRate EOL
END
RETURN
FaceApproachSP:
SeqLabC StockOnNoCan XSPC EOL { for SameTool ApproachFace }
SeqLabC StockOff ZOpCPC EOL
SeqLabC Feed StockOnNoCan ZSPC FeedRate EOL
RETURN
AppMove:
ThisOpEntryZCP
RETURN
Approach: { NOT FOR TAILSTOCK, .82 }
IF ApproachOD?
SeqLabC ThisOpEntryXCP AppMove EOL
ODApproachSP
ELSE
IF ApproachID?
SeqLabC XOpCD AppMove EOL
IDApproachSP
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP StockOff AppMove EOL
FaceApproachSP
END
END
RETURN
CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
IF NewToolOffset?
SeqLabC LOfstOff '00' EOL
SeqLabC OpToolID LatheOffset EOL
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
SeqLabC SpeedC EOL
ELSE
SeqLabC 'G50' MaxRPM EOL
SeqLabC CSSOn 'G96' Speed EOL
END
ELSE
IF LAST ConstantSurfaceFeed?
SeqLabC CSSOff 'G97' Speed EOL
ELSE
SeqLabC SpeedC EOL
END
END
IF LAST ProgStop?
SeqLabC SpinOn EOL
SeqLabC CoolOn EOL
ELSE
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
DoPostScript
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC: { 4.2 }
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
CRCOnC
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN
ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Dwell?
SeqLabC 'G4U' Dwell# EOL
END
ELSE
IF CannedCycle?
SeqLab
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
IF LastFeat? AND Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC FeedC MoveZC Speed InverseSpinOn EOL
ELSE
SeqLabC FeedC CkCRC MoveXC MoveZC FeedRateC EOL
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN
CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
RapidC
END
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
SetAbs
PosSideLathe
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ABSOLUTE INCHES )' EOL
END
END
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
OpenSub
{HARD-CODED BAR PULL ROUTINE}
'N1' Preset Rapid 'T0808' SpinOff EOL
SeqLabC 'X0.Z0.' EOL
SeqLabC 'M11' EOL
SeqLabC 'G4U.3' EOL
SeqLabC 'G0Z0.' EOL
SeqLabC 'M10' EOL
SeqLabC 'G4U.5' EOL
SeqLabC 'G0Z3.' EOL
'Åš2 '
{ensures that N1 will not be output anywhere but in bar puller for M99 loop at program end}
StockOff {.71.2}
SetHome
DoOpComments
DoPostScript
Plane
SeqLabC OpToolID LatheOffset Preset Rapid EOL
SeqLabC CoolOn EOL
IF ConstantSurfaceFeed?
SeqLabC 'G50' MaxRPM EOL
SeqLabC CSSOn 'G96'
ELSE
SeqLabC CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF NewTool?
{Finish off last Operation}
StockOff {.62}
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC EOL
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END
{Start new Operation}
DoOpComments
DoPostScript
SeqLabC OpToolID LatheOffset Preset Rapid EOL
SeqLabC CoolOn EOL
IF ConstantSurfaceFeed?
SeqLabC 'G50' MaxRPM EOL
SeqLabC CSSOn 'G96'
ELSE
SeqLabC CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF SameTool? {.62}
{Start new Operation}
DoOpComments
StockOff
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
CheckOffset
ODApproachSP
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
CheckOffset
IDApproachSP
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
CheckOffset
FaceApproachSP
END
END
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
IF ApproachFace?
SeqLabC LCycle 'Z' FirstMoveEPZ# XatFinZ XTapAtZ FeedRate EOL
ELSE
SeqLabC LCycle XatFinZ FinZ XTapAtZ FeedRate EOL
END
SimpleRough
ELSE
TagInc
IF RoughContour?
SetPass2
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft CutDepth FeedRate EOL
'>' Tag# EOL
SeqLab StepMove StrtPosC EOL
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
ELSE
IF RoughPatternShift?
SetPass2
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft XminusU ZminusW NumCuts FeedRate EOL
'>' Tag# EOL
SeqLab Rapid StrtPos EOL
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
END
END
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
SeqLabC LCycle XatFinZ FinZ XTapAtZ ThrdHeight CutDepth ThrdLead ToolAngle EOL
IF AutoFinish?
SeqLabC 'G92' XatFinZ FinZ XTapAtZ ThrdLead EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF PeckChipBreaker?
SeqLabC LCycle ZDepth RLevel Dwell Peck Retract FeedRate EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4U' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish?
IF NOT Drilling? AND NOT Grooving?
StockOff
IF Turning?
SetPass1
ELSE
SetPass2
END
SeqLabC RapidC StrtPos EOL
ToolPath
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}
{End of program ************************************************************}
{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
RapidC
END
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC EOL
DoEndOpPS
SeqLabC CoolOff EOL
SeqLabC 'M89' EOL
SeqLabC '/M99P1' EOL
IF ProgStop?
SeqLabC 'M0' EOL
END
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
Wyszukiwarka
Podobne podstrony:
Fanuc 10T MS [PT] L703 85 1Fanuc 10T MS [BMR] L768 85Fanuc 10T MS [ TPM] L455 85Fanuc 10T MS [ CES] L107 85Fanuc 10T MS [AMF] L424 85 1Fanuc 10T MS [RHB] L458 85Fanuc 10T MS ( ót) L131 85 1Fanuc 10T MS [ BI] L441 85Fanuc 10T MS ( AG) L092 85 1Fanuc 10T MS [R PSI] L648 85 1Fanuc 10T MS [R PSI] L647 85 1Fanuc 10T MS [DMW] L745 85 2więcej podobnych podstron