RRRRRRRRRRRRRRRRRRRRRRRRRRR
projectlibrary
Make Your Own Jump Rings
by Howard Siegel
An artist s money-saving method
MATERIALS:
18-gauge round fine silver wire, 50
18-gauge round sterling wire, 9
TOOLS:
Coil winder
3/8" (0.375") diameter mandrel
0.147" diameter mandrel (made from a 12
penny common nail 3?" long)
Spring clothes pin tool for applying tension
and guiding the wire
Flush wire cutter
Two small plastic containers for holding coils
and cut rings
Jeweler s saw
2/0 or 3/0 jeweler s saw blades.
V block tool used to hold the sterling coils
for sawing.
Sharp scissors with long handles and short
blades used to cut the fine silver coil.
Howard Siegel offers this tutorial on an
affordable way to make your own jump rings
TECHNIQUES:
with 18g wire. The rings he makes in this
Wire, tool-making.
tutorial were used to make the Chinese
Stretched Knot Chain that can be found in Step
by Step Wire Jewelry s Spring 2008 issue.
Copyright Interweave Not to be reprinted. All rights reserved.
page 1
publishers of Step by Step Wire Jewelry magazine . . . join the online beading community at www.BeadingDaily.com
Photos courtesy of the author and Herb Halpern.
Make Your Own Jump Rings
Step 1: Place the 0.375" diameter mandrel into the coil
winder. Insert one end of the 18-gauge fine
silver wire into a small hole, drilled through
one leg of the spring clothes pin that comes
out inside the rope groove.
Pull about 1 of the wire through this hole, and
through the jaws of the clothes pin. With chain
nose pliers, make a 90° bend about 1/2" from
the end of the wire. Insert the bent end
between two of the jaws of the chuck holding
the mandrel. This will hold the wire so that you
can wind the coil.
Turn the crank of the coil winder clockwise to
wind the wire around the mandrel. Use the
clothes pin tool to guide the wire so that the Saw through the coil with the saw blade tipped
Step 1
turns of the wire coil lie side by side with no at about a 45 angle so that you are only
gap between the turns. cutting through two or three turns at any time.
Continue winding with the remainder of the When the stack of cut rings becomes unstable
wire. Slide the coil off the mandrel and place
into one of the plastic containers. The coil
should have at least 37 turns.
Step 2: Place the 0.147" diameter mandrel into the coil
winder.
Make a 90° bend about 1/2" from the end of
the wire. Wind a coil about 2 long. Cut the
wire. Continue winding coils until all of the 18g
sterling wire has been used.
Tip: Limiting the length of the sterling coils to
about 2 makes them easier to cut in the V
block tool using the jeweler s saw.
Step 2
Step 3: Place a saw blade into one end of the jeweler s and shifts, stop sawing, and remove the saw
saw frame. Insert the saw blade through the and coil from the V. Use the pointed scribe or
center of a sterling coil. Place the other end of
the saw blade into the other saw clamp,
slightly compress the saw frame, and tighten
the clamp on the saw blade. This applies
tension on the saw blade making it easier to
cut.
Apply lubricant to the saw blade by pulling the
teeth of the saw through beeswax or another
suitable lubricant.
Place the coil in the bottom of the V and pull
the coil forward, using the teeth of the saw
blade, until the near end of the coil is firmly
against the stop. Hold the back of the coil
with you left hand always maintaining pressure
Step 3
against the end stop. awl to pull the cut rings from the rear of the V
Copyright Interweave. Not to be reprinted. All rights reserved.
page 2
publishers of Step by Step Wire Jewelry magazine . . . join the online beading community at www.BeadingDaily.com
Make Your Own Jump Rings
Saw through the coil with the saw blade tipped pointing down the length of the coil and
at about a 45° angle so that you are only should also be pointed between the pad of your
cutting through two or three turns at any time. thumb and your fingers. This will assure that
When the stack of cut rings becomes unstable you do not cut your hand.
and shifts, stop sawing, and remove the saw With the scissors, cut the coil. When further
and coil from the V. Use the pointed scribe or cutting becomes difficult, withdraw the scissors
awl to pull the cut rings from the rear of the V from the coil. Brush the cut rings from the
into the plastic container. scissor blade into the second plastic container.
Reinsert the coil into the V, being very careful Reinsert the scissors into the coil. Take care to
to align the saw blade with the cut end of the align the blades with the cut end of the last
last ring. It is imperative that the saw blade be turn on the coil. Continue cutting the coil until
aligned with the partial cut in the rings on the it has all been reduced to rings.
coil. If not properly aligned, there will be two
cuts in the ring, one only partially through the
ring. When you try to open a ring with this
second partial cut, the ring will break. After HOWARD SIEGEL
properly aligning the blade in the coil, Retired from an engineering
continue sawing until all of the rings on the career in 1992, and has been
coil have been cut. taking classes at the William
TIP: There may be some cut rings on the saw Holland School since 1994.
blade. These rings must be removed by rotating He has been actively working
them until the cut through the ring is aligned in the lapidary arts,
with the blade. The rings will then just slide silversmithing and chain
off the blade. making. He teaches lost wax
casting and advanced chain making at the William
Step 4: Grasp the fine silver coil in your left hand (if Holland School. He is a past president and active
you re right-handed) and hold the coil against member of the Society for Midwest Metalsmiths in
the pad of your thumb with your fingers. The St. Louis, Mo. and has taught chain making
coil should cross your palm at about a 45° workshops for them, Craft Alliance, and the Jacoby
angle. Take the scissors in your right hand, and Arts Center, Alton, Ill. He has a Masters in
insert one blade inside the coil while the other Metallurgy, and taught it at Washington University
blade is above the coil. The scissors should be for 10 years. His work will be featured in a soon to
be released book, Twisted Wire.
Step 4
Copyright Interweave. Not to be reprinted. All rights reserved.
page 3
publishers of Step by Step Wire Jewelry magazine . . . join the online beading community at www.BeadingDaily.com
RRRRRRRRRRRRRRRRRRRRRRRRRRR
projectlibrary
Fusing Fine Silver Rings
by Howard Siegel
TOOLS:
Fusing or soldering board with smooth
surface
Fire brick or an annealing pan
Butane fueled torch or Bernz-O-Matic
propane fueled pencil torch
Tweezers
Open one quart plastic container with water
Optivisor or similar magnifier
Resource: Butane torch from Harbor Freight
Tool, harborfreight.com
TECHNIQUES:
Wire, fusing.
Step 1: Place the fusing plate on the annealing pan
or on top of the fire brick to lift it from the
surface of your bench to prevent burning
the bench with your torch.
Step 2: Close the fine silver rings so that the cut
Now that you ve learned how to make your
edges of the rings are in very good contact.
own jump rings, Howard Siegel explains how
This is done by over-forming the rings (or
bringing the cut edges of the rings past
to fuse them. The rings made in this tutorial
each other, carefully pulling them apart,
can be used in his Chinese Stretched Knot
aligning the cut edges so that they are
even when viewed from the edge of the
Chain project in the Spring 2008 issue of Step
ring, and when looking down the center of
by Step Wire Jewelry. Fusing is creating a joint
the ring.
in your rings, without the use of solder.
Copyright Interweave Not to be reprinted. All rights reserved.
page 1
publishers of Step by Step Wire Jewelry magazine . . . join the online beading community at www.BeadingDaily.com
Photos courtesy of the author and Herb Halpern.
Fusing Fine Silver Rings
Step 3: Place the closed ring on the fusing plate with
the cut facing forward. Close all of the fine
silver rings and place them in rows across the
fusing plate with the cut in each ring facing
the front of the plate.
Step 4: Turn down the lighting in the room to make it
easier to see the change in color of the rings as
they are heated for fusing. Put on your
Optivisor so that you can clearly watch the
joint in each ring as it is heated for fusing.
Step 5: Light the torch. Start with the ring at the rear
Step 3
left of the plate if holding the torch in your
right hand. This will keep you hand away from
previously fused rings, and minimizes the
opportunity to be accidentally burned.
Step 6: Move the torch flame in a circular motion
around the ring to be fused until it turns dull
red. Move the flame to the joint in the ring and
move the flame in a small circle concentrating
the heat evenly on both sides of the joint.
If the flame continues to be held on the joint,
the ring will melt completely through, and a
ball of metal will start to form on either side of
the joint. If this occurs, toss it, the ring is
scrap.
Step 6a
Step 7: Fuse all of the fine silver rings. You will need
In a short time the silver at the joint will melt and
surface tension will pull the molten metal together
30 fused rings to complete the Chinese
forming a joint. As soon as the metal melts, the flame
Stretched Knot Chain in the Spring issue of
must be removed from the joint. If the flame is kept on
Step by Step Wire Jewelry. Slide all of the fused the joint, the joint area will get hotter and begin to thin
out.
rings off the fusing plate and into the water
filled container to cool them.
Step 8: As an experiment, deliberately overheat the
first ring that you try to fuse so that you can
observe what happens when a ring is
overheated. This operation is called fusing, and
creates a joint without the use of solder.
HOWARD SIEGEL
Retired from an engineering career in 1992, and has been taking
classes at the William Holland School since 1994. He has been actively
working in the lapidary arts, silversmithing and chain making. He
teaches lost wax casting and advanced chain making at the William
Holland School. He is a past president and active member of the
Society for Midwest Metalsmiths in St. Louis, Mo. and has taught
Step 6b
chain making workshops for them, Craft Alliance, and the Jacoby Arts
Center, Alton, Ill. He has a Masters in Metallurgy, and taught it at
Washington University for 10 years. His work will be featured in a
soon to be released book, Twisted Wire.
Copyright Interweave. Not to be reprinted. All rights reserved.
page 2
publishers of Step by Step Wire Jewelry magazine . . . join the online beading community at www.BeadingDaily.com
Wyszukiwarka
Podobne podstrony:
How to Make your Own Tracer AmmunitionHow to make your own power BleederMake your own origami craneMake Your Own Miracle Achieve The Impossiblehow to make your own cue filesHow to Make Your Own PerfumeSpeedWealth How to make A Million In Your Own Business in 3 Years or lessTraffic Authority Sell Your Own ProductsPlany i budowa szafek kuchennych Woodsmith Magazine Plans Now Build Your Own Kitchen Cabinets(gardening) Grow Your Own Vegetable Sproutsmodifying or creating your own skinBuild Your Own Solid State Sonar System [Lou Garner]2008 04 Attic Tv Building Your Own Video Server(Gardening) Grow Your Own Beans And PeasLama Thubten Yeshe Make Your Mind an Oceanwięcej podobnych podstron