63-1
Front bumper cover
Assembly overview, up to 10.00
Note:
The following procedure is for removing the front
bumper cover. For instructions on removal of the
front bumper reinforcement please see Page 50-
2 , Lock carrier and front bumper reinforcement,
removing and installing up to 10.00.
1 -
Cover
Material: PP/EPDM
Removing:
- Remove turn signals.
- Separate release lever - 15 - from trunk
lock Page Page 63-7 .
- Unscrew screws - 9 -, - 10 - and - 14 -.
Pull cover out from guides -4- (left and
right-hand side).
2 -
Bumper carrier
3 -
Bolt
Qty. 2
20 Nm
63-2
4 -
Guide
To remove/install bumper cover, pull out or
push in parallel to guides at left and right.
Adjusting guides Page 63-8
5 -
Bolt
Qty. 6
2 Nm
6 -
Hexagon nut
Qty. 2
7 -
Impact damper
8 -
Bolt
Qty. 7
50 Nm
9 -
Bolt
Qty. 4
3 Nm
63-3
10 -
Bolt
Qty. 8
2 Nm
11 -
Spoiler
Clipped into cover
Is not necessary to remove when removing
the cover
12 -
Bolt
Qty. 2
13 -
Bumper strip
Clipped into cover
14 -
Quick release bolt
Qty. 3
2 Nm
15 -
Release lever
Removing Page 63-7
63-4
Assembly overview from 10.00 on
Note:
The following procedure is for removing the front
bumper cover. For instructions on removal of the
front bumper reinforcement please see Page 50-
5 , Lock carrier and front bumper reinforcement,
removing and installing from 10.00 on.
1 -
Cover
Material -PP/EPDM
Removing:
- Remove radiator grille Page 66-10
- Remove screws -2-, -5- and -10-. Pull
cover off guide pieces -3- (left and right).
2 -
Bolt
Qty: 6
6 Nm
3 -
Guide piece
To remove and install bumper cover, pull
out or slide into guide pieces in parallel
manner (left and right).
63-5
4 -
Screw
Qty: 3
2 Nm
5 -
Screw
Qty: 8
2 Nm
6 -
Speed nut
Qty: 6
7 -
Bumper strip
Clipped into cover
8 -
Ventilation grill
Consists of three parts and is clipped into
cover
9 -
Spoiler
Clipped into cover
Does not have to be removed when
removing cover
10 -
Quick-release screws
Qty: 3
2 Nm
63-6
Bumper strip, removing and installing
from 10.00 on
- Loosen clip -5- from inside of cover -3-.
- From center of vehicle, loosen bumper trim -1- from front retaining clip -
2- and pull out of guides -4- toward front.
- Chrome strip -6- is only secured to bumper trim via retaining clips in
certain versions. These retaining clips must be removed from the inside
of the bumper trim.
63-7
Release lever, removing
- Open release lever -1- with a screwdriver -2- and pull off hood lock.
- Pull release lever -1- with guide out from lock carrier.
63-8
Guide, adjusting
- Adjust slide -2- on guide -1- so that between headlight -4- and upper
edge of guide -1- a gap of 2 mm exists (-3- special tool 3371).
- Check and adjust gaps/shut lines with special tool 3371
Wyszukiwarka
Podobne podstrony:
Audi?? Front Bumper RemovalBentleyPublishers com Audi?? Service ResetVW Passat B7VW Passat (3C) Parking BrakeVW Passat 08 110 KM?BB?ne diagnostyczne63 1 Front bumperVW PASSAT; 01plVW Passat 1 9Dvw passat tdi halas na biegu luzemVW PASSAT 1991vw passat? Electric Wiring DiagramVW PASSAT 1990vw passat ABSvw passat B5 poduszka powietrzna 2vw passat przerwy w dzialaniu klimatyzacjiVW Passat 2 0Rozmieszczenie elementów centralnego zameka VW Passat B5dodatkowe ogrzewanie (farelka) VW PASSAT B5FLwięcej podobnych podstron