budynas SM ch14


budynas_SM_ch14.qxd 12/05/2006 17:39 Page 349
FIRST PAGES
Chapter 14
14-1
N 22
d = = = 3.667 in
P 6
Table 14-2: Y = 0.331
Ądn Ą(3.667)(1200)
V = = = 1152 ft/min
12 12
1200 + 1152
Eq. (14-4b): Kv = = 1.96
1200
T 63 025H 63 025(15)
t
W = = = = 429.7 lbf
d/2 nd/2 1200(3.667/2)
Eq. (14-7):
t
KvW P 1.96(429.7)(6)
 = = = 7633 psi = 7.63 kpsi Ans.
FY 2(0.331)
14-2
16
d = = 1.333 in, Y = 0.296
12
Ą(1.333)(700)
V = = 244.3 ft/min
12
1200 + 244.3
Eq. (14-4b): Kv = = 1.204
1200
63 025H 63 025(1.5)
t
W = = = 202.6 lbf
nd/2 700(1.333/2)
Eq. (14-7):
t
KvW P 1.204(202.6)(12)
 = = = 13 185 psi = 13.2 kpsi Ans.
FY 0.75(0.296)
14-3
d = mN = 1.25(18) = 22.5mm, Y = 0.309
Ą(22.5)(10-3)(1800)
V = = 2.121 m/s
60
6.1 + 2.121
Eq. (14-6b): Kv = = 1.348
6.1
60H 60(0.5)(103)
Wt = = = 235.8N
Ądn Ą(22.5)(10-3)(1800)
t
KvW 1.348(235.8)
Eq. (14-8):  = = = 68.6MPa Ans.
FmY 12(1.25)(0.309)
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 350
FIRST PAGES
350 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
14-4
d = 5(15) = 75 mm, Y = 0.290
Ą(75)(10-3)(200)
V = = 0.7854 m/s
60
Assume steel and apply Eq. (14-6b):
6.1 + 0.7854
Kv = = 1.129
6.1
60H 60(5)(103)
Wt = = = 6366 N
Ądn Ą(75)(10-3)(200)
t
KvW 1.129(6366)
Eq. (14-8):  = = = 82.6MPa Ans.
FmY 60(5)(0.290)
14-5
d = 1(16) = 16 mm, Y = 0.296
Ą(16)(10-3)(400)
V = = 0.335 m/s
60
Assume steel and apply Eq. (14-6b):
6.1 + 0.335
Kv = = 1.055
6.1
60H 60(0.15)(103)
t
W = = = 447.6N
Ądn Ą(16)(10-3)(400)
t
KvW 1.055(447.6)
Eq. (14-8): F = = = 10.6mm
 mY 150(1)(0.296)
From Table A-17, use F = 11 mm Ans.
14-6
d = 1.5(17) = 25.5mm, Y = 0.303
Ą(25.5)(10-3)(400)
V = = 0.534 m/s
60
6.1 + 0.534
Eq. (14-6b): Kv = = 1.088
6.1
60H 60(0.25)(103)
t
W = = = 468 N
Ądn Ą(25.5)(10-3)(400)
t
KvW 1.088(468)
Eq. (14-8): F = = = 14.9mm
 mY 75(1.5)(0.303)
Use F = 15 mm Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 351
FIRST PAGES
Chapter 14 351
14-7
24
d = = 4.8in, Y = 0.337
5
Ą(4.8)(50)
V = = 62.83 ft/min
12
1200 + 62.83
Eq. (14-4b): Kv = = 1.052
1200
63 025H 63 025(6)
t
W = = = 3151 lbf
nd/2 50(4.8/2)
t
KvW P 1.052(3151)(5)
Eq. (14-7): F = = = 2.46 in
 Y 20(103)(0.337)
Use F = 2.5in Ans.
14-8
16
d = = 3.2in, Y = 0.296
5
Ą(3.2)(600)
V = = 502.7 ft/min
12
1200 + 502.7
Eq. (14-4b): Kv = = 1.419
1200
63 025(15)
t
W = = 984.8 lbf
600(3.2/2)
t
KvW P 1.419(984.8)(5)
Eq. (14-7): F = = = 2.38 in
 Y 10(103)(0.296)
Use F = 2.5in Ans.
14-9 Try P = 8 which gives d = 18/8 = 2.25 in and Y = 0.309.
Ą(2.25)(600)
V = = 353.4 ft/min
12
1200 + 353.4
Eq. (14-4b): Kv = = 1.295
1200
63 025(2.5)
Wt = = 233.4 lbf
600(2.25/2)
t
KvW P 1.295(233.4)(8)
Eq. (14-7): F = = = 0.783 in
 Y 10(103)(0.309)
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 352
FIRST PAGES
352 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
Using coarse integer pitches from Table 13-2, the following table is formed.
t
Pd V Kv W F
2 9.000 1413.717 2.178 58.356 0.082
3 6.000 942.478 1.785 87.535 0.152
4 4.500 706.858 1.589 116.713 0.240
6 3.000 471.239 1.393 175.069 0.473
8 2.250 353.429 1.295 233.426 0.782
10 1.800 282.743 1.236 291.782 1.167
12 1.500 235.619 1.196 350.139 1.627
16 1.125 176.715 1.147 466.852 2.773
Other considerations may dictate the selection. Good candidates are P = 8(F = 7/8in)
and P = 10 (F = 1.25 in). Ans.
14-10 Try m = 2mmwhich gives d = 2(18) = 36 mm and Y = 0.309.
Ą(36)(10-3)(900)
V = = 1.696 m/s
60
6.1 + 1.696
Eq. (14-6b): Kv = = 1.278
6.1
60(1.5)(103)
t
W = = 884 N
Ą(36)(10-3)(900)
1.278(884)
Eq. (14-8): F = = 24.4mm
75(2)(0.309)
Using the preferred module sizes from Table 13-2:
t
md VKv W F
1.00 18.0 0.848 1.139 1768.388 86.917
1.25 22.5 1.060 1.174 1414.711 57.324
1.50 27.0 1.272 1.209 1178.926 40.987
2.00 36.0 1.696 1.278 884.194 24.382
3.00 54.0 2.545 1.417 589.463 12.015
4.00 72.0 3.393 1.556 442.097 7.422
5.00 90.0 4.241 1.695 353.678 5.174
6.00 108.0 5.089 1.834 294.731 3.888
8.00 144.0 6.786 2.112 221.049 2.519
10.00 180.0 8.482 2.391 176.839 1.824
12.00 216.0 10.179 2.669 147.366 1.414
16.00 288.0 13.572 3.225 110.524 0.961
20.00 360.0 16.965 3.781 88.419 0.721
25.00 450.0 21.206 4.476 70.736 0.547
32.00 576.0 27.143 5.450 55.262 0.406
40.00 720.0 33.929 6.562 44.210 0.313
50.00 900.0 42.412 7.953 35.368 0.243
Other design considerations may dictate the size selection. For the present design,
m = 2mm(F = 25 mm) is a good selection. Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 353
FIRST PAGES
Chapter 14 353
14-11
22 60
dP = = 3.667 in, dG = = 10 in
6 6
Ą(3.667)(1200)
V = = 1152 ft/min
12
1200 + 1152
Eq. (14-4b): Kv = = 1.96
1200
63 025(15)
t
W = = 429.7 lbf
1200(3.667/2)

Table 14-8: Cp = 2100 psi [Note: using Eq. (14-13) can result in wide variation in
Cp due to wide variation in cast iron properties]
3.667 sin 20 10 sin 20
Eq. (14-12): r1 = = 0.627 in, r2 = = 1.710 in
2 2
1/2
t
KvW 1 1
Eq. (14-14): C =-Cp +
F cos Ć r1 r2
1/2
1.96(429.7) 1 1
=-2100 +
2 cos 20 0.627 1.710
=-65.6(103) psi =-65.6 kpsi Ans.
14-12
16 48
dP = = 1.333 in, dG = = 4in
12 12
Ą(1.333)(700)
V = = 244.3 ft/min
12
1200 + 244.3
Eq. (14-4b): Kv = = 1.204
1200
63 025(1.5)
t
W = = 202.6 lbf
700(1.333/2)
"
Table 14-8: Cp = 2100 psi (see note in Prob. 14-11 solution)
1.333 sin 20 4 sin 20
Eq. (14-12): r1 = = 0.228 in, r2 = = 0.684 in
2 2
Eq. (14-14):
1/2
1.202(202.6) 1 1
C =-2100 + =-100(103)
F cos 20 0.228 0.684
2
2100 1.202(202.6) 1 1
F = + = 0.668 in
100(103) cos 20 0.228 0.684
Use F = 0.75 in Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 354
FIRST PAGES
354 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
14-13
24 48
dP = = 4.8in, dG = = 9.6in
5 5
Ą(4.8)(50)
V = = 62.83 ft/min
12
600 + 62.83
Eq. (14-4a): Kv = = 1.105
600
63 025H
t
W = = 525.2H
50(4.8/2)
"
Table 14-8: Cp = 1960 psi (see note in Prob. 14-11 solution)
4.8 sin 20ć%
Eq. (14-12): r1 = = 0.821 in, r2 = 2r1 = 1.642 in
2
1/2
1.105(525.2H) 1 1
Eq. (14-14): -100(103) =-1960 +
2.5 cos 20ć% 0.821 1.642
H = 5.77 hp Ans.
14-14
dP = 4(20) = 80 mm, dG = 4(32) = 128 mm
Ą(80)(10-3)(1000)
V = = 4.189 m/s
60
3.05 + 4.189
Kv = = 2.373
Eq. (14-6a):
3.05
60(10)(103)
t
W = = 2387 N
Ą(80)(10-3)(1000)
"
Table 14-8: Cp = 163 MPa (see note in Prob. 14-11 solution)
80 sin 20 128 sin 20
Eq. (14-12): r1 = = 13.68 mm, r2 = = 21.89 mm
2 2
1/2
2.373(2387) 1 1
C =-163 + =-617 MPa Ans.
Eq. (14-14):
50 cos 20 13.68 21.89
14-15 The pinion controls the design.
Bending YP = 0.303, YG = 0.359
17 30
dP = = 1.417 in, dG = = 2.500 in
12 12
ĄdPn Ą(1.417)(525)
V = = = 194.8 ft/min
12 12
1200 + 194.8
Eq. (14-4b): Kv = = 1.162
1200

Eq. (6-8): Se = 0.5(76) = 38 kpsi
Eq. (6-19): ka = 2.70(76)-0.265 = 0.857
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 355
FIRST PAGES
Chapter 14 355
2.25 2.25
l = = = 0.1875 in
Pd 12
3YP 3(0.303)
Eq. (14-3): x = = = 0.0379 in
2P 2(12)

Eq. (b), p. 717: t = 4(0.1875)(0.0379) = 0.1686 in

Eq. (6-25): de = 0.808 0.875(0.1686) = 0.310 in
-0.107
0.310
Eq. (6-20): kb = = 0.996
0.30
kc = kd = ke = 1, kf1 = 1.66 (see Ex. 14-2)
0.300
rf = = 0.025 in (see Ex. 14-2)
12
r rf 0.025
= = = 0.148
d t 0.1686
Approximate D/d ="with D/d = 3; from Fig. A-15-6, Kt = 1.68.
From Fig. 6-20, with Sut = 76 kpsi and r = 0.025 in, q = 0.62. From Eq. (6-32)
Kf = 1 + 0.62(1.68 - 1) = 1.42
Miscellaneous-Effects Factor:

1
kf = kf 1kf 2 = 1.65 = 1.247
1.323
Eq. (7-17): Se = 0.857(0.996)(1)(1)(1)(1.247)(38 000)
= 40 450 psi
40 770
all = = 18 120 psi
2.25
FYPall 0.875(0.303)(18 120)
Wt = =
Kv Pd 1.162(12)
= 345 lbf
345(194.8)
H = = 2.04 hp Ans.
33 000
Wear
1 = 2 0.292, E1 = E2 30(106) psi
ł= łł=
ł śł

1
ł
Eq. (14-13): Cp = = 2285 psi
ł śł
śł
ł - 0.2922
ł
1
2Ą
30(106)
dP 1.417
Eq. (14-12):
r1 = sin Ć = sin 20 = 0.242 in
2 2
dG 2.500
r2 = sin Ć = sin 20 = 0.428
2 2
1 1 1 1
+ = + = 6.469 in-1
r1 r2 0.242 0.428
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 356
FIRST PAGES
356 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
From Eq. (6-68),
8
(SC)10 = 0.4HB - 10 kpsi
= [0.4(149) - 10](103) = 49 600 psi
8
(SC)10 -49 600
C,all =- " = " =-33 067 psi
n
2.25
2
-33 067 0.875 cos 20
t
Eq. (14-14):
W = = 22.6 lbf
2285 1.162(6.469)
22.6(194.8)
H = = 0.133 hp Ans.
33 000
Rating power (pinion controls):
H1 = 2.04 hp
H2 = 0.133 hp
Hall = (min 2.04, 0.133) = 0.133 hp Ans.
14-16 See Prob. 14-15 solution for equation numbers.
Pinion controls: YP = 0.322, YG = 0.447
Bending dP = 20/3 = 6.667 in, dG = 33.333 in
V = ĄdPn/12 = Ą(6.667)(870)/12 = 1519 ft/min
Kv = (1200 + 1519)/1200 = 2.266

Se = 0.5(113) = 56.5 kpsi
ka = 2.70(113)-0.265 = 0.771
l = 2.25/Pd = 2.25/3 = 0.75 in
x = 3(0.322)/[2(3)] = 0.161 in

t = 4(0.75)(0.161) = 0.695 in

de = 0.808 2.5(0.695) = 1.065 in
kb = (1.065/0.30)-0.107 = 0.873
kc = kd = ke = 1
rf = 0.300/3 = 0.100 in
r rf 0.100
= = = 0.144
d t 0.695
From Table A-15-6, Kt = 1.75; Fig. 6-20, q = 0.85; Eq. (6-32), K = 1.64
f
kf 2 = 1/1.597, kf = kf 1kf 2 = 1.66/1.597 = 1.039
Se = 0.771(0.873)(1)(1)(1)(1.039)(56 500) = 39 500 psi
all = Se/n = 39 500/1.5 = 26 330 psi
FYPall 2.5(0.322)(26 330)
t
W = = = 3118 lbf
Kv Pd 2.266(3)
H = Wt V/33 000 = 3118(1519)/33 000 = 144 hp Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 357
FIRST PAGES
Chapter 14 357
Wear

Eq. (14-13):
Cp = 2285 psi
Eq. (14-12): r1 = (6.667/2) sin 20 = 1.140 in
r2 = (33.333/2) sin 20 = 5.700 in
SC = [0.4(262) - 10](103) = 94 800 psi
Eq. (6-68):
"
"
C,all =-SC/ nd =-94 800/ 1.5 =-77 404 psi
2
C,all F cos Ć 1
t
W =
Cp Kv 1/r1 + 1/r2
2
-77 404 2.5 cos 20 1
=
2300 2.266 1/1.140 + 1/5.700
= 1115 lbf
t
W V 1115(1519)
H = = = 51.3hp Ans.
33 000 33 000
For 108 cycles (revolutions of the pinion), the power based on wear is 51.3 hp.
Rating power pinion controls
H1 = 144 hp
H2 = 51.3hp
Hrated = min(144, 51.3) = 51.3hp Ans.
14-17 Given: Ć = 20, n = 1145 rev/min, m = 6 mm, F = 75 mm, NP = 16 milled teeth,
NG = 30T, Sut = 900 MPa, HB = 260, nd = 3, YP = 0.296, and YG = 0.359.
Pinion bending
dP = mNP = 6(16) = 96 mm
dG = 6(30) = 180 mm
ĄdPn Ą(96)(1145)(10-3)(12)
V = = = 5.76 m/s
12 (12)(60)
6.1 + 5.76
Eq. (14-6b): Kv = = 1.944
6.1

Se = 0.5(900) = 450 MPa
a = 4.45, b =-0.265
ka = 4.51(900)-0.265 = 0.744
l = 2.25m = 2.25(6) = 13.5mm
x = 3Ym/2 = 3(0.296)6/2 = 2.664 mm
"
t = 4lx = 4(13.5)(2.664) = 12.0mm

de = 0.808 75(12.0) = 24.23 mm
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 358
FIRST PAGES
358 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
-0.107
24.23
kb = = 0.884
7.62
kc = kd = ke = 1
rf = 0.300m = 0.300(6) = 1.8mm
From Fig. A-15-6 for r/d = rf /t = 1.8/12 = 0.15, Kt = 1.68.
Figure 6-20, q = 0.86; Eq. (6-32),
K = 1 + 0.86(1.68 - 1) = 1.58
f
kf 1 = 1.66 (Gerber failure criterion)
kf 2 = 1/K = 1/1.537 = 0.651
f
kf = kf 1kf 2 = 1.66(0.651) = 1.08
Se = 0.744(0.884)(1)(1)(1)(1.08)(450) = 319.6MPa
Se 319.6
all = = = 245.8MPa
nd 1.3
FYmall 75(0.296)(6)(245.8)
Eq. (14-8): Wt = = = 16 840 N
Kv 1.944
Tn 16 840(96/2)(1145)
H = = = 96.9kW Ans.
9.55 9.55(106)
Wear: Pinion and gear
Eq. (14-12): r1 = (96/2) sin 20ć% = 16.42 mm
r2 = (180/2) sin 20ć% = 30.78 mm
Eq. (14-13), with E = 207(103) MPa and  = 0.292, gives

"
1
Cp = = 190 MPa
2Ą(1 - 0.2922)/(207 103)
Eq. (6-68): SC = 6.89[0.4(260) - 10] = 647.7MPa
S 647.7
C,all =-"C =- " =-568 MPa
n
1.3
2
C,all F cos Ć 1
Eq. (14-14): Wt =
Cp Kv 1/r1 + 1/r2
2
-568 75 cos 20ć% 1
=
191 1.944 1/16.42 + 1/30.78
= 3433 N
WtdP 3433(96)
T = = = 164 784 N mm = 164.8N m
2 2
Tn 164.8(1145)
H = = = 19 758.7W= 19.8kW Ans.
9.55 9.55
Thus, wear controls the gearset power rating; H = 19.8kW. Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 359
FIRST PAGES
Chapter 14 359
14-18 Preliminaries: NP = 17, NG = 51
N 17
dP = = = 2.833 in
Pd 6
51
dG = = 8.500 in
6
V = ĄdPn/12 = Ą(2.833)(1120)/12 = 830.7 ft/min
Eq. (14-4b): Kv = (1200 + 830.7)/1200 = 1.692
Sy 90 000
all = = = 45 000 psi
nd 2
Table 14-2: YP = 0.303, YG = 0.410
FYPall 2(0.303)(45 000)
Eq. (14-7): Wt = = = 2686 lbf
Kv Pd 1.692(6)
WtV 2686(830.7)
H = = = 67.6hp
33 000 33 000
Based on yielding in bending, the power is 67.6 hp.
(a) Pinion fatigue
Bending
.
Eq. (2-17): Sut = 0.5HB = 0.5(232) = 116 kpsi

Eq. (6-8): Se = 0.5Sut = 0.5(116) = 58 kpsi
Eq. (6-19): a = 2.70, b =-0.265, ka = 2.70(116)-0.265 = 0.766
1 1.25 2.25 2.25
Table 13-1: l = + = = = 0.375 in
Pd Pd Pd 6
3YP 3(0.303)
Eq. (14-3): x = = = 0.0758
2Pd 2(6)
"
Eq. (b), p. 717: t = 4lx = 4(0.375)(0.0758) = 0.337 in
"
Eq. (6-25): de = 0.808 Ft = 0.808 2(0.337) = 0.663 in
-0.107
0.663
Eq. (6-20): kb = = 0.919
0.30
kc = kd = ke = 1. Assess two components contributing to kf . First, based upon
one-way bending and the Gerber failure criterion, kf 1 = 1.66 (see Ex. 14-2). Second,
due to stress-concentration,
0.300 0.300
rf = = = 0.050 in (see Ex. 14-2)
Pd 6
r rf 0.05
Fig. A-15-6: = = = 0.148
d t 0.338
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 360
FIRST PAGES
360 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
Estimate D/d =" by setting D/d = 3, Kt = 1.68. From Fig. 6-20, q = 0.86, and
Eq. (6-32)
K = 1 + 0.86(1.68 - 1) = 1.58
f
1 1
kf 2 = = = 0.633
K 1.58
f
kf = kf 1kf 2 = 1.66(0.633) = 1.051
Se = 0.766(0.919)(1)(1)(1)(1.051)(58) = 42.9 kpsi
Se 42.9
all = = = 21.5 kpsi
nd 2
FYPall 2(0.303)(21 500)
Wt = = = 1283 lbf
Kv Pd 1.692(6)
t
W V 1283(830.7)
H = = = 32.3hp Ans.
33 000 33 000
(b) Pinion fatigue
Wear
From Table A-5 for steel:  = 0.292, E = 30(106) psi
Eq. (14-13) or Table 14-8:
1/2

1
Cp = = 2285 psi
2Ą[(1 - 0.2922)/30(106)]
In preparation for Eq. (14-14):
dP 2.833
Eq. (14-12): r1 = sin Ć = sin 20ć% = 0.485 in
2 2
dG 8.500
r2 = sin Ć = sin 20ć% = 1.454 in
2 2

1 1 1 1
+ = + = 2.750 in
r1 r2 0.485 1.454
8
Eq. (6-68): (SC)10 = 0.4HB - 10 kpsi
In terms of gear notation
C = [0.4(232) - 10]103 = 82 800 psi
We will introduce the design factor of nd = 2 and because it is a contact stress apply it
"
to the load Wt by dividing by 2.
 82 800
C,all =-"c =- " =-58 548 psi
2 2
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 361
FIRST PAGES
Chapter 14 361
Solve Eq. (14-14) for Wt:
2
-58 548 2 cos 20ć%
Wt = = 265 lbf
2285 1.692(2.750)
265(830.7)
Hall = = 6.67 hp Ans.
33 000
For 108 cycles (turns of pinion), the allowable power is 6.67 hp.
(c) Gear fatigue due to bending and wear
Bending
3YG 3(0.4103)
Eq. (14-3): x = = = 0.1026 in
2Pd 2(6)

Eq. (b), p. 717: t = 4(0.375)(0.1026) = 0.392 in

Eq. (6-25): de = 0.808 2(0.392) = 0.715 in
-0.107
0.715
Eq. (6-20): kb = = 0.911
0.30
kc = kd = ke = 1
r rf 0.050
= = = 0.128
d t 0.392
Approximate D/d =" by setting D/d = 3 for Fig. A-15-6; Kt = 1.80. Use K =
f
1.80.
1
kf 2 = = 0.556, kf = 1.66(0.556) = 0.923
1.80
Se = 0.766(0.911)(1)(1)(1)(0.923)(58) = 37.36 kpsi
Se 37.36
all = = = 18.68 kpsi
nd 2
FYGall 2(0.4103)(18 680)
Wt = = = 1510 lbf
Kv - Pd 1.692(6)
1510(830.7)
Hall = = 38.0hp Ans.
33 000
The gear is thus stronger than the pinion in bending.
Wear Since the material of the pinion and the gear are the same, and the contact
stresses are the same, the allowable power transmission of both is the same. Thus,
Hall = 6.67 hp for 108 revolutions of each. As yet, we have no way to establish SC for
108/3 revolutions.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 362
FIRST PAGES
362 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
(d) Pinion bending: H1 = 32.3hp
Pinion wear: H2 = 6.67 hp
Gear bending: H3 = 38.0hp
Gear wear: H4 = 6.67 hp
Power rating of the gear set is thus
Hrated = min(32.3, 6.67, 38.0, 6.67) = 6.67 hp Ans.
14-19 dP = 16/6 = 2.667 in, dG = 48/6 = 8in
Ą(2.667)(300)
V = = 209.4 ft/min
12
33 000(5)
t
W = = 787.8 lbf
209.4
Assuming uniform loading, Ko = 1. From Eq. (14-28),
Qv = 6, B = 0.25(12 - 6)2/3 = 0.8255
A = 50 + 56(1 - 0.8255) = 59.77
Eq. (14-27):
0.8255
"
59.77 + 209.4
Kv = = 1.196
59.77
From Table 14-2,
NP = 16T, YP = 0.296
NG = 48T, YG = 0.4056
From Eq. (a), Sec. 14-10 with F = 2in
0.0535
"
2 0.296
(Ks)P = 1.192 = 1.088
6
0.0535
"
2 0.4056
(Ks)G = 1.192 = 1.097
6
From Eq. (14-30) with Cmc = 1
2
Cpf = - 0.0375 + 0.0125(2) = 0.0625
10(2.667)
Cpm = 1, Cma = 0.093 (Fig. 14-11), Ce = 1
Km = 1 + 1[0.0625(1) + 0.093(1)] = 1.156
Assuming constant thickness of the gears KB = 1
mG = NG/NP = 48/16 = 3
With N (pinion) = 108 cycles and N (gear) = 108/3, Fig. 14-14 provides the relations:
(YN )P = 1.3558(108)-0.0178 = 0.977
(YN )G = 1.3558(108/3)-0.0178 = 0.996
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 363
FIRST PAGES
Chapter 14 363
Ł
Fig. 14-6: JP = 0.27, JG = 0.38
From Table 14-10 for R = 0.9, KR = 0.85
KT = Cf = 1

cos 20ć% sin 20ć% 3
Eq. (14-23) with mN = 1 I = = 0.1205
2 3 + 1

Table 14-8: Cp = 2300 psi
Strength: Grade 1 steel with HBP = HBG = 200
Fig. 14-2: (St)P = (St)G = 77.3(200) + 12 800 = 28 260 psi
Fig. 14-5: (Sc)P = (Sc)G = 322(200) + 29 100 = 93 500 psi
Fig. 14-15: (ZN )P = 1.4488(108)-0.023 = 0.948
(ZN )G = 1.4488(108/3)-0.023 = 0.973
4"
Fig. 14-12: HBP/HBG = 1 CH = 1
Pinion tooth bending
Eq. (14-15):

Pd Km KB 6 (1.156)(1)
t
( )P = W KoKv Ks = 787.8(1)(1.196)(1.088)
F J 2 0.27
= 13 167 psi Ans.
Factor of safety from Eq. (14-41)

StYN /(KT KR) 28 260(0.977)/[(1)(0.85)]
(SF)P = = = 2.47 Ans.
 13 167
Gear tooth bending

6 (1.156)(1)
( )G = 787.8(1)(1.196)(1.097) = 9433 psi Ans.
2 0.38
28 260(0.996)/[(1)(0.85)]
(SF)G = = 3.51 Ans.
9433
Pinion tooth wear
1/2
Km Cf
Eq. (14-16): (c)P = Cp Wt KoKv Ks
dP F I
P
1/2
1.156 1
= 2300 787.8(1)(1.196)(1.088)
2.667(2) 0.1205
= 98 760 psi Ans.
Eq. (14-42):

Sc ZN /(KT KR) 93 500(0.948)/[(1)(0.85)]
(SH)P = = = 1.06 Ans.
c 98 760
P
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 364
FIRST PAGES
364 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
Gear tooth wear
1/2 1/2
(Ks)G 1.097
(c)G = (c)P = (98 760) = 99 170 psi Ans.
(Ks)P 1.088
93 500(0.973)(1)/[(1)(0.85)]
(SH)G = = 1.08 Ans.
99 170
The hardness of the pinion and the gear should be increased.
14-20 dP = 2.5(20) = 50 mm, dG = 2.5(36) = 90 mm
ĄdPnP Ą(50)(10-3)(100)
V = = = 0.2618 m/s
60 60
60(120)
t
W = = 458.4N
Ą(50)(10-3)(100)
Eq. (14-28): Ko = 1, Qv = 6, B = 0.25(12 - 6)2/3 = 0.8255
A = 50 + 56(1 - 0.8255) = 59.77
"
0.8255
59.77 + 200(0.2618)
Eq. (14-27): Kv = = 1.099
59.77
Table 14-2: YP = 0.322, YG = 0.3775
Similar to Eq. (a) of Sec. 14-10 but for SI units:
"
0.0535
1
Ks = = 0.8433 mF Y
kb
"
0.0535
(Ks)P = 0.8433 2.5(18) 0.322 = 1.003 use 1
"
0.0535
(Ks)G = 0.8433 2.5(18) 0.3775 > 1 use 1
18
Cmc = 1, F = 18/25.4 = 0.709 in, Cpf = - 0.025 = 0.011
10(50)
Cpm = 1, Cma = 0.247 + 0.0167(0.709) - 0.765(10-4)(0.7092) = 0.259
Ce = 1
KH = 1 + 1[0.011(1) + 0.259(1)] = 1.27
Eq. (14-40): KB = 1, mG = NG/NP = 36/20 = 1.8
Fig. 14-14: (YN )P = 1.3558(108)-0.0178 = 0.977
(YN )G = 1.3558(108/1.8)-0.0178 = 0.987
Fig. 14-6: (YJ )P = 0.33, (YJ )G = 0.38
Eq. (14-38): YZ = 0.658 - 0.0759 ln(1 - 0.95) = 0.885
Sec. 14-15:
Y = Z = 1
R
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 365
FIRST PAGES
Chapter 14 365
Eq. (14-23) with mN = 1:

cos 20ć% sin 20ć% 1.8
ZI = = 0.103
2 1.8 + 1
"
Table 14-8: ZE = 191 MPa
Strength Grade 1 steel, given HBP = HBG = 200
Fig. 14-2: (FP)P = (FP)G = 0.533(200) + 88.3 = 194.9MPa
Fig. 14-5: (HP)P = (HP)G = 2.22(200) + 200 = 644 MPa
Fig. 14-15: (ZN )P = 1.4488(108)-0.023 = 0.948
(ZN )G = 1.4488(108/1.8)-0.023 = 0.961
Fig. 14-12: 4"
HBP/HBG = 1 ZW = 1
Pinion tooth bending

1 KH KB
t
( )P = W KoKv Ks
bmt YJ P

1 1.27(1)
= 458.4(1)(1.099)(1) = 43.08 MPa Ans.
18(2.5) 0.33

FP YN 194.9 0.977
Eq. (14-41): (SF)P = = = 4.99 Ans.
 YYZ P 43.08 1(0.885)
Gear tooth bending

1 1.27(1)
Eq. (14-15): ( )G = 458.4(1)(1.099)(1) = 37.42 MPa Ans.
18(2.5) 0.38

194.9 0.987
(SF)G = = 5.81 Ans.
37.42 1(0.885)
Pinion tooth wear


KH Z
R
t
Eq. (14-16): (c)P = ZE W KoKv Ks
dw1b ZI P


1.27 1
= 191 458.4(1)(1.099)(1) = 501.8MPa Ans.
50(18) 0.103

HP ZN ZW 644 0.948(1)
(SH)P = = = 1.37 Ans.
Eq. (14-42):
c YYZ P 501.8 1(0.885)
Gear tooth wear
1/2 1/2
(Ks)G 1
(c)G = (c)P = (501.8) = 501.8MPa Ans.
(Ks)P 1

644 0.961(1)
(SH)G = = 1.39 Ans.
501.8 1(0.885)
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 366
FIRST PAGES
366 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
14-21
Pt = Pn cos  = 6 cos 30 = 5.196 teeth/in
16 48
dP = = 3.079 in, dG = (3.079) = 9.238 in
5.196 16
Ą(3.079)(300)
V = = 241.8 ft/min
12
0.8255
"
33 000(5) 59.77 + 241.8
t
W = = 682.3 lbf, Kv = = 1.210
241.8 59.77
From Prob. 14-19:
YP = 0.296, YG = 0.4056
(Ks)P = 1.088, (Ks)G = 1.097, KB = 1
mG = 3, (YN )P = 0.977, (YN )G = 0.996, KR = 0.85
(St)P = (St)G = 28 260 psi, CH = 1, (Sc)P = (Sc)G = 93 500 psi
"
(ZN )P = 0.948, (ZN )G = 0.973, Cp = 2300 psi
The pressure angle is:

tan 20
Eq. (13-19): Ćt = tan-1 = 22.80
cos 30
3.079
(rb)P = cos 22.8 = 1.419 in, (rb)G = 3(rb)P = 4.258 in
2
a = 1/Pn = 1/6 = 0.167 in
Eq. (14-25):
1/2 1/2
2 2
3.079 9.238
Z = + 0.167 - 1.4192 + + 0.167 - 4.2582
2 2

3.079 9.238
- + sin 22.8
2 2
= 0.9479 + 2.1852 - 2.3865 = 0.7466 Conditions O.K. for use
Ą
pN = pn cos Ćn = cos 20 = 0.4920 in
6
pN 0.492
Eq. (14-21): mN = = = 0.6937
0.95Z 0.95(0.7466)

sin 22.8 cos 22.8 3
Eq. (14-23): I = = 0.193
2(0.6937) 3 + 1

Ł Ł
Fig. 14-7: JP = 0.45, JG = 0.54
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 367
FIRST PAGES
Chapter 14 367
Fig. 14-8: Corrections are 0.94 and 0.98
JP = 0.45(0.94) = 0.423, JG = 0.54(0.98) = 0.529
2
Cmc = 1, Cpf = - 0.0375 + 0.0125(2) = 0.0525
10(3.079)
Cpm = 1, Cma = 0.093, Ce = 1
Km = 1 + (1)[0.0525(1) + 0.093(1)] = 1.146
Pinion tooth bending

5.196 1.146(1)
( )P = 682.3(1)(1.21)(1.088) = 6323 psi Ans.
2 0.423
28 260(0.977)/[1(0.85)]
(SF)P = = 5.14 Ans.
6323
Gear tooth bending

5.196 1.146(1)
( )G = 682.3(1)(1.21)(1.097) = 5097 psi Ans.
2 0.529
28 260(0.996)/[1(0.85)]
(SF)G = = 6.50 Ans.
5097
Pinion tooth wear
1/2
1.146 1
(c)P = 2300 682.3(1)(1.21)(1.088) = 67 700 psi Ans.
3.078(2) 0.193
93 500(0.948)/[(1)(0.85)]
(SH)P = = 1.54 Ans.
67 700
Gear tooth wear
1/2
1.097
(c)G = (67 700) = 67 980 psi Ans.
1.088
93 500(0.973)/[(1)(0.85)]
(SH)G = = 1.57 Ans.
67 980
14-22 Given: NP = 17T, NG = 51T, R = 0.99 at 108 cycles, HB = 232 through-hardening
Grade 1, core and case, both gears.
Table 14-2: YP = 0.303, YG = 0.4103
Fig. 14-6: JP = 0.292, JG = 0.396
dP = NP/P = 17/6 = 2.833 in, dG = 51/6 = 8.5 in
Pinion bending
From Fig. 14-2:
7
(St)10 = 77.3HB + 12 800
0.99
= 77.3(232) + 12 800 = 30 734 psi
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 368
FIRST PAGES
368 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
Fig. 14-14: YN = 1.6831(108)-0.0323 = 0.928
V = ĄdPn/12 = Ą(2.833)(1120/12) = 830.7ft/min
"
KT = KR = 1, SF = 2, SH = 2
30 734(0.928)
all = = 14 261 psi
2(1)(1)
Qv = 5, B = 0.25(12 - 5)2/3 = 0.9148
A = 50 + 56(1 - 0.9148) = 54.77
0.9148
"
54.77 + 830.7
Kv = = 1.472
54.77
0.0535
"
2 0.303
Ks = 1.192 = 1.089 ! use 1
6
Km = Cmf = 1 + Cmc(Cpf Cpm + CmaCe)
Cmc = 1
F
Cpf = - 0.0375 + 0.0125F
10d
2
= - 0.0375 + 0.0125(2)
10(2.833)
= 0.0581
Cpm = 1
Cma = 0.127 + 0.0158(2) - 0.093(10-4)(22) = 0.1586
Ce = 1
Km = 1 + 1[0.0581(1) + 0.1586(1)] = 1.2167
K = 1
FJPall
t
Eq. (14-15):
W =
KoKv Ks Pd Km KB
2(0.292)(14 261)
= = 775 lbf
1(1.472)(1)(6)(1.2167)(1)
t
W V 775(830.7)
H = = = 19.5hp
33 000 33 000
Pinion wear
Fig. 14-15: ZN = 2.466N-0.056 = 2.466(108)-0.056 = 0.879
MG = 51/17 = 3

sin 20ć% cos 20ć% 3
I = = 1.205, CH = 1
2 3 + 1
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 369
FIRST PAGES
Chapter 14 369
7
Fig. 14-5: (Sc)10 = 322HB + 29 100
0.99
= 322(232) + 29 100 = 103 804 psi
103 804(0.879)
c,all = " = 64 519 psi
2(1)(1)
2
c,all FdP I
t
Eq. (14-16): W =
Cp KoKv Ks KmCf
2
64 519 2(2.833)(0.1205)
=
2300 1(1.472)(1)(1.2167)(1)
= 300 lbf
t
W V 300(830.7)
H = = = 7.55 hp
33 000 33 000
The pinion controls therefore Hrated = 7.55 hp Ans.
14-23
3Y
l = 2.25/Pd, x =
2Pd


"
2.25 3Y 3.674"
t = 4lx = 4 = Y
Pd 2Pd Pd


"

" "
3.674 F Y
de = 0.808 Ft = 0.808 F Y = 1.5487
Pd Pd

ł ł-0.107
" -0.0535
"
1.5487 F Y/Pd
F Y
ł łł
kb = = 0.8389
0.30 Pd
0.0535
"
1 F Y
Ks = = 1.192 Ans.
kb Pd
14-24 YP = 0.331, YG = 0.422, JP = 0.345, JG = 0.410, Ko = 1.25. The service conditions
are adequately described by Ko. Set SF = SH = 1.
dP = 22/4 = 5.500 in
dG = 60/4 = 15.000 in
Ą(5.5)(1145)
V = = 1649 ft/min
12
Pinion bending
7
(St)10 = 77.3HB + 12 800 = 77.3(250) + 12 800 = 32 125 psi
0.99
YN = 1.6831[3(109)]-0.0323 = 0.832
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 370
FIRST PAGES
370 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
32 125(0.832)
Eq. (14-17): (all)P = = 26 728 psi
1(1)(1)
B = 0.25(12 - 6)2/3 = 0.8255
A = 50 + 56(1 - 0.8255) = 59.77
0.8255
"
59.77 + 1649
Kv = = 1.534
59.77
Ks = 1, Cm = 1
F
Cmc = - 0.0375 + 0.0125F
10d
3.25
= - 0.0375 + 0.0125(3.25) = 0.0622
10(5.5)
Cma = 0.127 + 0.0158(3.25) - 0.093(10-4)(3.252) = 0.178
Ce = 1
Km = Cmf = 1 + (1)[0.0622(1) + 0.178(1)] = 1.240
KB = 1, KT = 1
26 728(3.25)(0.345)
t
Eq. (14-15): W1 = = 3151 lbf
1.25(1.534)(1)(4)(1.240)
3151(1649)
H1 = = 157.5hp
33 000
t
Gear bending By similar reasoning, W2 = 3861 lbf and H2 = 192.9hp
Pinion wear
mG = 60/22 = 2.727

cos 20ć% sin 20ć% 2.727
I = = 0.1176
2 1 + 2.727
7
(Sc)10 = 322(250) + 29 100 = 109 600 psi
0.99
(ZN )P = 2.466[3(109)]-0.056 = 0.727
(ZN )G = 2.466[3(109)/2.727]-0.056 = 0.769
109 600(0.727)
(c,all)P = = 79 679 psi
1(1)(1)
2
c,all FdP I
t
W3 =
Cp KoKv Ks KmCf
2
79 679 3.25(5.5)(0.1176)
= = 1061 lbf
2300 1.25(1.534)(1)(1.24)(1)
1061(1649)
H3 = = 53.0hp
33 000
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 371
FIRST PAGES
Chapter 14 371
Gear wear
t
Similarly, W4 = 1182 lbf, H4 = 59.0hp
Rating
Hrated = min(H1, H2, H3, H4)
= min(157.5, 192.9, 53, 59) = 53 hp Ans.
Note differing capacities. Can these be equalized?
14-25 From Prob. 14-24:
t t
W1 = 3151 lbf, W2 = 3861 lbf,
t t
W3 = 1061 lbf, W4 = 1182 lbf
33 000Ko H 33 000(1.25)(40)
t
W = = = 1000 lbf
V 1649
Pinion bending: The factor of safety, based on load and stress, is
t
W1 3151
(SF)P = = = 3.15
1000 1000
Gear bending based on load and stress
t
W2 3861
(SF)G = = = 3.86
1000 1000
Pinion wear
t
W3 1061
based on load: n3 = = = 1.06
1000 1000
"
based on stress: (SH)P = 1.06 = 1.03
Gear wear
t
W4 1182
based on load: n4 = = = 1.18
1000 1000
"
based on stress: (SH)G = 1.18 = 1.09
Factors of safety are used to assess the relative threat of loss of function 3.15, 3.86, 1.06,
1.18 where the threat is from pinion wear. By comparison, the AGMA safety factors
(SF)P, (SF)G, (SH)P, (SH)G
are
3.15, 3.86, 1.03, 1.09 or 3.15, 3.86, 1.061/2, 1.181/2
and the threat is again from pinion wear. Depending on the magnitude of the numbers,
using SF and SH as defined by AGMA, does not necessarily lead to the same conclusion
concerning threat. Therefore be cautious.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 372
FIRST PAGES
372 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
14-26 Solution summary from Prob. 14-24: n = 1145 rev/min, Ko = 1.25, Grade 1 materials,
NP = 22T, NG = 60T, mG = 2.727, YP = 0.331, YG = 0.422, JP = 0.345,
JG = 0.410, Pd = 4T /in, F = 3.25 in, Qv = 6, (Nc)P = 3(109), R = 0.99
Pinion HB: 250 core, 390 case
Gear HB: 250 core, 390 case
Km = 1.240, KT = 1, KB = 1, dP = 5.500 in, dG = 15.000 in,
V = 1649 ft/min, Kv = 1.534, (Ks)P = (Ks)G = 1, (YN )P = 0.832,
(YN )G = 0.859, KR = 1
Bending
(all)P = 26 728 psi (St)P = 32 125 psi
(all)G = 27 546 psi (St)G = 32 125 psi
t
W1 = 3151 lbf, H1 = 157.5hp
t
W2 = 3861 lbf, H2 = 192.9hp
Wear
Ć = 20ć%, I = 0.1176, (ZN )P = 0.727,

(ZN )G = 0.769, CP = 2300 psi
(Sc)P = Sc = 322(390) + 29 100 = 154 680 psi
154 680(0.727)
(c,all)P = = 112 450 psi
1(1)(1)
154 680(0.769)
(c,all)G = = 118 950 psi
1(1)(1)
2
112 450 2113(1649)
t
W3 = (1061) = 2113 lbf, H3 = = 105.6hp
79 679 33 000
2
118 950 2354(1649)
t
W4 = (1182) = 2354 lbf, H4 = = 117.6hp
109 600(0.769) 33 000
Rated power
Hrated = min(157.5, 192.9, 105.6, 117.6) = 105.6hp Ans.
Prob. 14-24
Hrated = min(157.5, 192.9, 53.0, 59.0) = 53 hp
The rated power approximately doubled.
14-27 The gear and the pinion are 9310 grade 1, carburized and case-hardened to obtain Brinell
285 core and Brinell 580 600 case.
Table 14-3:
7
(St)10 = 55 000 psi
0.99
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 373
FIRST PAGES
Chapter 14 373
Modification of St by (YN )P = 0.832 produces
(all)P = 45 657 psi,
Similarly for (YN )G = 0.859
(all)G = 47 161 psi, and
t
W1 = 4569 lbf, H1 = 228 hp
t
W2 = 5668 lbf, H2 = 283 hp

From Table 14-8, Cp = 2300 psi. Also, from Table 14-6:
7
(Sc)10 = 180 000 psi
0.99
Modification of Sc by (YN ) produces
(c,all)P = 130 525 psi
(c,all)G = 138 069 psi
and
t
W3 = 2489 lbf, H3 = 124.3hp
t
W4 = 2767 lbf, H4 = 138.2hp
Rating
Hrated = min(228, 283, 124, 138) = 124 hp Ans.
14-28 Grade 2 9310 carburized and case-hardened to 285 core and 580 case in Prob. 14-27.
Summary:
7
Table 14-3: (St)10 = 65 000 psi
0.99
(all)P = 53 959 psi
(all)G = 55 736 psi
and it follows that
t
W1 = 5399.5 lbf, H1 = 270 hp
t
W2 = 6699 lbf, H2 = 335 hp

From Table 14-8, Cp = 2300 psi. Also, from Table 14-6:
Sc = 225 000 psi
(c,all)P = 181 285 psi
(c,all)G = 191 762 psi
Consequently,
t
W3 = 4801 lbf, H3 = 240 hp
t
W4 = 5337 lbf, H4 = 267 hp
Rating
Hrated = min(270, 335, 240, 267) = 240 hp. Ans.
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 374
FIRST PAGES
374 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
14-29 n = 1145 rev/min, Ko = 1.25, NP = 22T, NG = 60T, mG = 2.727, dP = 2.75 in,
dG = 7.5in, YP = 0.331, YG = 0.422, JP = 0.335, JG = 0.405, P = 8T /in,
F = 1.625 in, HB = 250, case and core, both gears. Cm = 1, F/dP = 0.0591,
Cf = 0.0419, Cpm = 1, Cma = 0.152, Ce = 1, Km = 1.1942, KT = 1,
K = 1, Ks = 1, V = 824 ft/min, (YN )P = 0.8318, (YN )G = 0.859, KR = 1,
I = 0.117 58
7
(St)10 = 32 125 psi
0.99
(all)P = 26 668 psi
(all)G = 27 546 psi
and it follows that
t
W1 = 879.3 lbf, H1 = 21.97 hp
t
W2 = 1098 lbf, H2 = 27.4hp
For wear
t
W3 = 304 lbf, H3 = 7.59 hp
t
W4 = 340 lbf, H4 = 8.50 hp
Rating
Hrated = min(21.97, 27.4, 7.59, 8.50) = 7.59 hp
In Prob. 14-24, Hrated = 53 hp
Thus
7.59 1 1
= 0.1432 = , not Ans.
53.0 6.98 8
The transmitted load rating is
t
Wrated = min(879.3, 1098, 304, 340) = 304 lbf
In Prob. 14-24
t
Wrated = 1061 lbf
Thus
304 1 1
= 0.2865 = , not , Ans.
1061 3.49 4
14-30 SP = SH = 1, Pd = 4, JP = 0.345, JG = 0.410, Ko = 1.25
Bending
7
Table 14-4: (St)10 = 13 000 psi
0.99
13 000(1)
(all)P = (all)G = = 13 000 psi
1(1)(1)
allFJP 13 000(3.25)(0.345)
t
W1 = = = 1533 lbf
KoKv Ks Pd Km KB 1.25(1.534)(1)(4)(1.24)(1)
1533(1649)
H1 = = 76.6hp
33 000
t t
W2 = W1 JG/JP = 1533(0.410)/0.345 = 1822 lbf
H2 = H1 JG/JP = 76.6(0.410)/0.345 = 91.0hp
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 375
FIRST PAGES
Chapter 14 375
Wear

Table 14-8: Cp = 1960 psi
7
Table 14-7: (Sc)10 = 75 000 psi = (c,all)P = (c,all)G
0.99
2
(c,all)P FdpI
t
W3 =
Cp KoKv Ks KmCf
2
75 000 3.25(5.5)(0.1176)
t
W3 = = 1295 lbf
1960 1.25(1.534)(1)(1.24)(1)
t t
W4 = W3 = 1295 lbf
1295(1649)
H4 = H3 = = 64.7hp
33 000
Rating
Hrated = min(76.7, 94.4, 64.7, 64.7) = 64.7hp Ans.
Notice that the balance between bending and wear power is improved due to CI s more
favorable Sc/St ratio. Also note that the life is 107 pinion revolutions which is (1/300) of
3(109). Longer life goals require power derating.
14-31 From Table A-24a, Eav = 11.8(106)
For Ć = 14.5ć% and HB = 156

1.4(81)
SC = = 51 693 psi
2 sin 14.5/[11.8(106)]
For Ć = 20ć%

1.4(112)
SC = = 52 008 psi
2 sin 20/[11.8(106)]
SC = 0.32(156) = 49.9 kpsi
14-32 Programs will vary.
14-33
(YN )P = 0.977, (YN )G = 0.996
(St)P = (St)G = 82.3(250) + 12 150 = 32 725 psi
32 725(0.977)
(all)P = = 37 615 psi
1(0.85)
37 615(1.5)(0.423)
t
W1 = = 1558 lbf
1(1.404)(1.043)(8.66)(1.208)(1)
1558(925)
H1 = = 43.7hp
33 000
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 376
FIRST PAGES
376 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
32 725(0.996)
(all)G = = 38 346 psi
1(0.85)
38 346(1.5)(0.5346)
t
W2 = = 2007 lbf
1(1.404)(1.043)(8.66)(1.208)(1)
2007(925)
H2 = = 56.3hp
33 000
(ZN )P = 0.948, (ZN )G = 0.973
7
Table 14-6: (Sc)10 = 150 000 psi
0.99

0.948(1)
(c,allow)P = 150 000 = 167 294 psi
1(0.85)
2
167 294 1.963(1.5)(0.195)
t
W3 = = 2074 lbf
2300 1(1.404)(1.043)
2074(925)
H3 = = 58.1hp
33 000
0.973
(c,allow)G = (167 294) = 171 706 psi
0.948
2
171 706 1.963(1.5)(0.195)
t
W4 = = 2167 lbf
2300 1(1.404)(1.052)
2167(925)
H4 = = 60.7hp
33 000
Hrated = min(43.7, 56.3, 58.1, 60.7) = 43.7hp Ans.
Pinion bending controlling
14-34
(YN )P = 1.6831(108)-0.0323 = 0.928
(YN )G = 1.6831(108/3.059)-0.0323 = 0.962
Table 14-3: St = 55 000 psi
55 000(0.928)
(all)P = = 60 047 psi
1(0.85)
60 047(1.5)(0.423)
t
W1 = = 2487 lbf
1(1.404)(1.043)(8.66)(1.208)(1)
2487(925)
H1 = = 69.7hp
33 000
0.962
(all)G = (60 047) = 62 247 psi
0.928

62 247 0.5346
t
W2 = (2487) = 3258 lbf
60 047 0.423
3258
H2 = (69.7) = 91.3hp
2487
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 377
FIRST PAGES
Chapter 14 377
Table 14-6: Sc = 180 000 psi
(ZN )P = 2.466(108)-0.056 = 0.8790
(ZN )G = 2.466(108/3.059)-0.056 = 0.9358
180 000(0.8790)
(c,all)P = = 186 141 psi
1(0.85)
2
186 141 1.963(1.5)(0.195)
t
W3 = = 2568 lbf
2300 1(1.404)(1.043)
2568(925)
H3 = = 72.0hp
33 000
0.9358
(c,all)G = (186 141) = 198 169 psi
0.8790
2
198 169 1.043
t
W4 = (2568) = 2886 lbf
186 141 1.052
2886(925)
H4 = = 80.9hp
33 000
Hrated = min(69.7, 91.3, 72, 80.9) = 69.7hp Ans.
Pinion bending controlling
14-35 (YN )P = 0.928, (YN )G = 0.962 (See Prob. 14-34)
Table 14-3: St = 65 000 psi
65 000(0.928)
(all)P = = 70 965 psi
1(0.85)
70 965(1.5)(0.423)
t
W1 = = 2939 lbf
1(1.404)(1.043)(8.66)(1.208)
2939(925)
H1 = = 82.4hp
33 000
65 000(0.962)
(all)G = = 73 565 psi
1(0.85)

73 565 0.5346
t
W2 = (2939) = 3850 lbf
70 965 0.423
3850
H2 = (82.4) = 108 hp
2939
budynas_SM_ch14.qxd 12/05/2006 17:39 Page 378
FIRST PAGES
378 Solutions Manual " Instructor s Solution Manual to Accompany Mechanical Engineering Design
Table 14-6: Sc = 225 000 psi
(ZN )P = 0.8790, (ZN )G = 0.9358
225 000(0.879)
(c,all)P = = 232 676 psi
1(0.85)
2
232 676 1.963(1.5)(0.195)
t
W3 = = 4013 lbf
2300 1(1.404)(1.043)
4013(925)
H3 = = 112.5hp
33 000
0.9358
(c,all)G = (232 676) = 247 711 psi
0.8790
2
247 711 1.043
t
W4 = (4013) = 4509 lbf
232 676 1.052
4509(925)
H4 = = 126 hp
33 000
Hrated = min(82.4, 108, 112.5, 126) = 82.4hp Ans.
The bending of the pinion is the controlling factor.


Wyszukiwarka

Podobne podstrony:
budynas SM ch11
budynas SM ch12
budynas SM ch09
budynas SM ch16
budynas SM ch05
budynas SM ch20
budynas SM ch02
budynas SM ch15
budynas SM ch01
Fanuc 6M [SM] PM956 17 3
5217 15492 1 SM Recenzje 03
ch14
kryteria SM
Projekt lotu fotogrametrycznego SM

więcej podobnych podstron