Rear axle, servicing (front-wheel-drive vehicles) Page 1 of 26
42-1
Rear axle, servicing (front-
wheel-drive vehicles)
WARNING!
Do not attempt to weld and/or straighten the
axle beam.
Do not re-use fasteners that are worn or
deformed in normal use.
Some fasteners are designed to be used only
once, and are unreliable and may fail if used
a second time. This includes, but is not
limited to, nuts, bolts, washers, circlips and
cotter pins. Always follow recommendations
in this manual-replace these fasteners with
new parts where indicated, and any other
time it is deemed necessary by inspection.
CAUTION!
If using power tools (pneumatic or electric), do
not tighten the bolted connections more than
hand-tight. Otherwise, the specified tightening
torques could be exceeded.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 2 of 26
42-2
1 -
Bolts
25 Nm (18 ft lb)
2 -
Gasket
Always replace
3 -
Bolt
Always replace
4 -
Mounting bracket
Do not remove in order to remove rear axle
Be careful when installing bolts
Notes:
If mounting bracket - 4 - is removed, carry
out a rough alignment of the rear axle after
installation Fig. 1 .
After all installation work is completed,
check and if necessary adjust the wheel
alignment page 44-13 .
5 -
Nut
Always replace
80 Nm (59 ft lb) + 1/4-turn (90 )
6 -
Bolt
Always replace
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 3 of 26
50 Nm (37 ft lb) + 1/4-turn (90 )
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 4 of 26
42-3
7 -
Suspension strut
Different versions vehicle data label,
page 42-5
Do not mix different versions
Identical part for left and right-sides
Removing and installing page 42-24
Servicing page 42-26
8 -
Nut
Always replace
9 -
Wheel bearing and wheel hub
Servicing page 42-16
10 -
Guide bushing
Removing and installing page 42-14
11 -
Bolt
Always replace
75 Nm (55 ft lb)
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 5 of 26
42-4
12 -
Axle beam
Removing and installing page 42-8
Through m.y. 1998 on vehicles with xenon
headlights a headlight range adjuster is
installed
If equipped with headlight range control
page 42-8
Refer to Note page 42-49
Contact surfaces for wheel bearing/wheel
hub and threaded holes must be free of
paint or dirt
After installing, check and if necessary
adjust wheel alignment
13 -
Balance weights
Note:
A new guide bushing has been introduced for the
A4 Avant and sedan which replaces the old guide
bushing and balance weights.
14 -
Retaining strap
Installing Figs. 2 and 3
15 -
Bolt
20 Nm (15 ft lb)
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 6 of 26
42-5
Information on weight codes (code number)
From m.y. 1998 , spring/shock assemblies will
be classified according to weight codes (code
number) so that suspension components can be
matched easily.
The spring/shock assembly installed in the
vehicle is indicated by the weight code on the
vehicle data label.
Example of vehicle data label
A - Weight code for front suspension
B - Weight code for rear suspension
The vehicle data label is located in the spare wheel well and in the vehicle
Maintenance booklet.
The weight codes can be used to identify the correct spring/shock
assemblies on the parts catalog microfiche.
The weight code for the different suspension versions is indicated by the
arrow in the illustration.
1BA: Standard suspension
1BE: Sport suspension
1BB: Heavy duty suspension (approx. 20 mm (3/4 in.) higher)
1BC: Special purpose suspension
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 7 of 26
1BD: Sport suspension, Audi S4
1BH: USA
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 8 of 26
42-6
1BT: Heavy duty suspension (approx. 7 mm or
1/4 in. higher)
1BP: Heavy duty suspension (same ride height
as 1BA but with limited bump)
Fig. 1 Rough alignment of rear axle
- With mounting bolts loosened, push rear axle fully forward (direction of
travel) and then center it from side-to-side using two rulers.
Checking wheel alignment page 44-6 .
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 9 of 26
42-7
Fig. 2 Installing retaining strap
- Press center of stabilizer bar toward axle beam.
Dimension -a-: approx. 8 mm (5/16 in.)
Fig. 3 Installing retaining strap (continued)
- Press stabilizer bar 8 mm (5/16 in.) toward axle beam, then install
retaining strap off-set to right.
Dimension -a-: 100 mm (3.94 in.)
- Make sure retaining strap contacts both axle beam and stabilizer bar
then fasten strap (lock facing upward).
Note:
If the axle beam is supplied with pre-drilled holes for mounting retaining
strap guide -b-, the guide must be used. Guide -b- correctly positions the
retaining strap and dimension -a- can then be ignored.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 10 of 26
42-8
Rear axle, removing and installing
Removing
Vehicle must be standing on its wheels
above vehicle lift
- Remove wheel trim.
On light alloy wheels use puller in vehicle tool kit to remove trim cap
- Raise vehicle.
- Extract brake fluid from reservoir:
Repair Manual, Brake System, Repair Group 47
- Remove wheels.
- Remove cover (arrows).
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 11 of 26
42-9
- Unbolt heat shield cover (arrows indicate bolted connections) and push
forward until parking brake cable adjuster becomes accessible.
- Loosen both cable adjusters as follows:
- Remove locking clip -D-.
- Screw in adjusting nut -C- up to stop.
- Push adjuster together.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 12 of 26
42-10
- Remove locking plates -1- on left and right-sides, slightly loosen bolts -
2- for cable retaining plate, and remove cables from axle beam.
- Disconnect brake lines at rear axle (arrow) on both sides.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 13 of 26
42-11
- Pull ABS wheel speed sensors out of mounting
holes on both sides.
- Detach ABS wheel speed sensor wiring from
rear axle.
- On vehicles with headlight range control remove
linkage from axle beam.
Note:
Use VAG1383 gearbox lifter together with 1359/2
attachment for removing and installing the axle
beam.
- Unbolt and remove suspension strut from axle beam.
- Remove bolts from guide bushings ( page 42-2 , items -3- and -5-)
and remove axle beam.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 14 of 26
42-12
Installing
- Install axle together with guide bushings into
mounting brackets and install bolts hand-tight.
- Install suspension struts and hand-tighten
suspension strut to axle beam bolts.
- Coat O-ring for ABS wheel speed sensor with
brake cylinder paste.
- Push ABS wheel speed sensors into wheel bearing housings up to
stop.
- Install locking plates for ABS wheel speed sensors.
- Route parking brake cables and attach to brake calipers.
- Connect brake lines.
- Adjust parking brake:
Repair Manual, Brake System, Repair Group 46
- Install heat shield.
- Bleed brakes:
Repair Manual, Brake System, Repair Group 47
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 15 of 26
42-13
CAUTION!
Vehicle must be standing on its wheels when
tightening guide bushing to rear axle bolts.
Otherwise bonded rubber bushings will be
subjected to torsion resulting in shortened
service life
- Tighten guide bushing bolts ( page 42-2 ,
items -3- and -5-).
Tightening torque: 80 Nm (59 ft lb) + 1/4-turn
(90 )
CAUTION!
Vehicle must be standing on its wheels when
tightening suspension strut to rear axle bolts.
Otherwise bonded rubber bushings will be
subjected to torsion resulting in shortened
service life
- Tighten suspension strut to axle beam bolts (
page 42-2 , items -6- and -8-).
Tightening torque: 50 Nm (37 ft lb) + 1/4-turn
(90 )
-
On vehicles with headlight range control, tighten
bolted connection between headlight range
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 16 of 26
control linkage to axle beam.
Tightening torque: 3 Nm +1/-0 Nm (27 in. lb +9/-
0 in. lb)
- Install cover below rear axle.
- Check wheel alignment and adjust if necessary
page 44-6 .
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 17 of 26
42-14
Guide bushings, removing and installing
Lowering rear axle
- On vehicles with headlight range control remove linkage from axle
beam.
- Remove bolts from guide bushing mount and lower axle.
- Position VW552 guide piece to prevent brake lines from becoming
stressed.
Removing guide bushing
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 18 of 26
42-15
Guide bushing installation position
The guide bushing must be pulled into the rear axle with the arrow on the
3128/1a installation piece pointing in direction -B-.
Pulling in guide bushing
The remainder of the installation is the reverse of removal.
CAUTION!
Vehicle must be standing on its wheels when tightening guide
bushing to rear axle bolts. Otherwise bonded rubber bushings will
be subjected to torsion resulting in shortened service life
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 19 of 26
42-16
Rear wheel bearing and wheel hub,
servicing
Before carrying out work on the wheel bearings or
wheel hub the wheel and brake caliper must be
removed:
Repair Manual, Brake System, Repair Group 46
CAUTION!
Suspend the brake caliper using a piece of
wire.
Do not allow the caliper to hang by the brake
hose. The unsupported weight can stretch
and damage the brake hose.
Do not attempt to weld or straighten the load
bearing components or parts of the
suspension
Notes:
Only re-install clean bearings; do not wash out
bearings.
Make sure wheel bearing clearance is set
carefully.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 20 of 26
42-17
1 -
Axle beam
Contact surface for stub axle must be free
of dirt
2 -
Stub axle
Different versions parts catalog
microfiche
3 -
Splash shield
4 -
Combi-bolt
30 Nm (22 ft lb)
5 -
Cotter pin
Always replace
6 -
Grease cap
Always replace
Forcing off Fig. 1
Driving in Fig. 2
7 -
Slotted ring
Install over nut - 8 -
8 -
Nut
Setting wheel bearing clearance Fig. 3
9 -
Thrust washer
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 21 of 26
42-18
10 -
Outer wheel bearing
Do not wash out if bearing is to be re-used
11 -
Outer wheel bearing outer race
Use copper arbor to drive out
Pressing in Fig. 4
Apply small quantity of wheel bearing
grease to wheel bearing seat before
pressing in bearing race
12 -
Brake disc with wheel hub
13 -
ABS wheel speed sensor rotor
Drive off evenly using copper arbor through
tapped holes in wheel hub
Pressing in Fig. 5
14 -
Inner wheel bearing outer race
Use copper arbor to drive out outer race
Apply small quantity of wheel bearing
grease to wheel bearing seat before
pressing in bearing race
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 22 of 26
42-19
15 -
Inner wheel bearing
Do not wash out if bearing is to be re-used
16 -
Seal
Always replace
Different versions parts catalog
microfiche
Fill area between sealing lips with multi-
purpose grease Fig. 7
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 23 of 26
42-20
Fig. 1 Removing grease cap
- Remove grease cap from seat by tapping gently on claw of tool.
Fig. 2 Driving on grease cap
Notes:
Damaged (dented/buckled) grease caps permit the penetration of
moisture and must always be replaced.
When installing a grease cap always use the tool shown to prevent
damage.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 24 of 26
42-21
Fig. 3 Setting wheel bearing clearance
Note:
Wheel bearing play is correct when the thrust washer can just be moved
using a screwdriver simply by applying pressure, without having to apply
force.
- Secure with slotted ring and new cotter pin.
Fig. 4 Pressing in outer race for outer wheel bearing
- Apply small quantity of wheel bearing grease to wheel bearing seat
before pressing in bearing race.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 25 of 26
42-22
Fig. 5 Pressing in ABS wheel speed sensor rotor
Fig. 6 Pressing in outer race for inner wheel bearing
- Apply small quantity of wheel bearing grease to wheel bearing seat
before pressing in bearing race.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Rear axle, servicing (front-wheel-drive vehicles) Page 26 of 26
42-23
Fig. 7 Fill groove (arrow) with grease
From m.y. 1998 , revised stub axles and dust lips will be installed
parts catalog microfiche.
Note:
For greater clarity, the seal is shown removed.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.1 11/20/2002
Wyszukiwarka
Podobne podstrony:
20 6 Fuel supply system front wheel drive 1 8T & 2 8Transmission for Front Wheel Drive Hybrid Powertreins HT146 29 Parking brake cable front wheel drve46 34 Parking brake cable all wheel drive42 93 Rear drive axle remove & install42 106 Wheel bearing housing remove & install42 65 Rear struts & upper control arm remove & install42 24 Rear struts remove & install40 17 Front drive axles remove & install40 1 Front axle componentsEV (Electric Vehicle) and Hybrid Drive Systems2002 09 Creating Virtual Worlds with Pov Ray and the Right Front End42 30 Marzec 2000 Dialog na warunkachBritney Spears (You Drive Me) Crazy42!więcej podobnych podstron