{Change Comments ***********************************************************}
{9/27/89, added PostScript to: Okuma OSP5000M-G M101.51, JR}
{3/29/90, Updated: Okuma OSP5000M-G M101.61 to .70.3 format, JR}
{7/5/90, Updated: Okuma OSP5000M-G M101.70.3 to .72.1 format, JR}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{12/19/90
Copied & modified: Okuma 5000M-G M101.73
For: Gibbs & Associates
Machine: Okuma
Control: 5000M-G
Updated to Version 3.2 per Fanuc 6M M001.76.1 Format.
DWB}
{4/03/91
Modified: Okuma 5000M-G M101.76.1
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}
{09/30/91
Modified: Okuma 5000M-G M101.79
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.81 Format.
Kim Michelman}
{2/11/94, Updated Okuma 5000M-G M101.81 to .81.2 format, JR}
{10/6/95, Updated Okuma 5000M-G M101.81.2 to .85 format per Fanuc 6M M001.85.01.03, JR}
{1/17/96, Updated .85 to .86 version, MPK}
{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}
{6/19/96
Initial: Okuma 5000M-G M101.89
Created: Okuma OSP7000M Mxxx.89
ForUser: DEN-TAL-EZ, Inc.
Control: Okuma OSP7000M
Machine: Okuma MC500H
Develop: ComPost 4.21.37, Catalyst68K v3.04.10.C
Comment: New Processor per manual.
Manual says it is totaly comapataple with the OSP5000M-G
and after some review it appears so!
Changed to First Tool Not In Spindle format.
Deleted PreTool
Moved OfstOn to nest line, off of the StrtPos line.
Added support for additional Drill Cycles.
Jim Radcliffe}
{5/11/98
Initial: Okuma OSP7000M M143.89
Created: Okuma OSP 700M Cadet Cxxx.12
ForUser: Muse Metal
Control: Okuma OSP 700M
Machine: Okuma Cadet
Develop: ComPost2 1.1b3, Virtual Gibbs 4.24
Comment: New processor per notes and marked up readout from Tome Muse.
Changed to Advance Mill per Fanuc 6M (FW) B001.12.10
Non-WFO output if NOT WFOCS
Changed G53 to G30P1.
G30P1 is set to retract Z to tool change position without moving XY.
G53 turns off tool length offset and retracts tool to home Z.
Added Rigid Tapping.
Use G94 instead of G95 in saftey start block.
Use G284 instead of G84 cycle call.
Use IPR feedrate.
Changed G80 to G0 at end of Drilling.
G80 causes a spindle stop between each hole.
Added CRCOffC to AutoCycCutSub2.
Jim Radcliffe}
{Prog Numeric Format Definitions ****}
#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*#####.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '##.#####;0.'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(TrackZNO#,4)
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(CSSubID#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Repeats#,5) {.72}
FORMAT(Dwell#,6)
FORMAT(FeedEntIPR#,7)
{Prog Subroutines ****}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
CalcCSWFO#:
ADD# MUL# NumOfCS# SUB# PartNum# Num#('1') CS#
RETURN
CSWFO:
' G15 H' ADD# CalcCSWFO# Num#('0')
RETURN
WFO:
' G15 H' ADD# PartNum# Num#('0')
RETURN
G52Stuff:
{using non-WFO output}
RETURN
WFOStuff:
IF MultipleParts? AND AllToolsOnePart?
{WFO called from CloseMP}
ELSE
IF WFOCS?
IF NOT SameTool?
SeqC CSWFO EOL
ELSE
IF ChangeCS?
IF MultipleParts?
{MP ChangeCS is hadled in SubCSMP and CloseMP}
ELSE
SeqC CSWFO EOL
END
END
END
ClearCSOffset
ELSE
IF NOT SameTool?
SeqC WFO EOL
END
END
END
RETURN
DoSubComment:
IF UseComments? AND SubComment?
' ( SUB NUMBER: ' Program# ' )' EOL
END
RETURN
DoCSWFOComment:
' ( CS#' CS# ' - ' CSComment$ ' )' EOL
' ( ' CSWFO '= X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ# ' )' EOL
RETURN
DoCSG52Comment:
' ( CS#' CS# ' - ' CSComment$ ' )' EOL
RETURN
OffsetComments:
IF NOT MultipleParts?
IF WFOCS?
IF ChangeCS?
DoCSWFOComment
END
ELSE
IF ChangeCS?
DoCSG52Comment
ELSE
IF NOT SameTool?
DoCSG52Comment
END
END
END
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
' ( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
' ( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
' ( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
' ( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
' ( ' ToolComment$ ' )' EOL
END
RestoreScale
END
OffsetComments
RETURN
AbsValueC:
IF NOT AbsValue?
AbsValue
END
RETURN
IncValueC:
IF AbsValue?
IncValue
END
RETURN
AbsOrIncC:
IF AbsoluteMoves?
AbsValueC
ELSE
IncValueC
END
RETURN
CSAngleA:
IF AAxisAvail?
' A' CSOffsetA#
END
RETURN
CSAngleAC:
IF AChange?
CSAngleA
END
RETURN
CSAngleB:
IF BAxisAvail?
' B' CSOffsetB#
END
RETURN
CSAngleBC:
IF BChange?
CSAngleB
END
RETURN
PSInit:
MasterOpF
CallMasterOpF
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN
StartSub:
OpenSub
SubID EOL
DoSubComment
RETURN
SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
' ( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN
StdSub:
SeqC ' CALL O' Program# ' Q' Repeats# EOL
StartSub
RETURN
FinishSub1: {part 1}
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN
FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
'RTS' EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN
ToggleIncDecWFO:
IF Flag?('3')
SetFlagF('3')
ELSE
SetFlag('3')
END
RETURN
OpenMP:
NewProg
IF WorkFixtureOffsets?
IF WFOCS?
StartSub
SaveCSProg
SaveCSOpStart
ClearCSOffset
ELSE
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
SeqC ' G15' SetWFO EOL
SeqC ' CALL O' Program# EOL
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
SeqC ' G15' SetWFO EOL
SeqC ' CALL O' Program# EOL
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
StartSub
END
ELSE
SeqC ' CALL O' Program# ' Q' Parts# EOL
StartSub
END
RETURN
DoCSWFOOps:
EachCSOp
DoCSWFOComment
ClearCSOffset
SeqC CSWFO EOL
SeqC ' CALL O' CSSubID# EOL
NextCSOp
RETURN
CloseMP:
IF WorkFixtureOffsets?
IF WFOCS?
'RTS' EOL
CloseSub
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoCSWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoCSWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
ELSE
'RTS' EOL
CloseSub
SeqC ' G15' WFO1 EOL
END
ELSE
SeqC AbsOrIncC EOL
SeqC Preset ShiftPC EOL
'RTS' EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN
SubCSMP:
IF WorkFixtureOffsets?
IF WFOCS?
IF ChangeCS?
'RTS' EOL
CloseSub
NewProg
StartSub
SaveCSProg
END
ClearCSOffset
END
END
RETURN
DoAbsOrInc:
IF Flag?('1')
IF ZMove?
IncValueC
ELSE
AbsOrIncC
END
END
RETURN
DoDrillAbsOrInc:
IF Flag?('1')
IF SPZMove?
IncValueC
ELSE
AbsOrIncC
END
END
RETURN
RestoreAbsOrInc:
IF Flag?('1')
SeqC AbsOrIncC EOL
END
RETURN
FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC ' CALL O' Program# EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF LastFeat?
SeqC DoAbsOrInc CRCOffC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC DoAbsOrInc RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC DoAbsOrInc CRCOnC RapidC MoveXYZC CRCOffsetC EOL
END
END
END
ELSE
IF LineFeat?
IF LastFeat?
SeqC DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC DoAbsOrInc CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC DoAbsOrInc CRCOnC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC DoAbsOrInc CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN
AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
Seq IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
ToolPath
SeqC AbsOrInc CRCOffC
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
'RTS' EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN
AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN
Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN
G92Sub:
SubWarning
StdSub
SeqC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN
ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC Feed IncValue StrtPosC EOL
SeqC AbsOrInc
ELSE
SeqC Feed
END
ELSE
SeqC Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqC AbsOrInc ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqC Rapid ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC ' CALL O' Program# EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
'RTS' EOL
CloseSub
{Element shift, not pattern}
RETURN
ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL
END
END
SeqC ' CALL O' Program# EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
'RTS' EOL
CloseSub
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
OpGuts:
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') {std sep sub Zreps are in effect} {rep change 2}
ZonlyRep {rep change 1}
SetFlagF('1') {not std sep sub Zreps in effect} {rep change 3}
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
IF FIFO?
SeqC FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
IF RetractToCP1?
SeqC ' G71' ZCP1 EOL
END
GetCycle
SeqC
IF Tap?
IF RigidTap?
IF CWSpindle?
' G284'
ELSE
' G274'
END
ELSE
IF CWSpindle?
' G84'
ELSE
' G74'
END
END
ELSE
Cycle
END
StrtPos ZDepth RLevel Dwell Peck Retract
IF RigidTap?
' F' FeedEntIPR#
ELSE
FeedEnt
END
FromCP EOL
IF CallMasterOp?
SeqC ' CALL O' CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqC ' CALL O' Program# EOL
StartSub
ToolPath
'RTS' EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqC Rapid ZCP3 EOL
IF Repeats?
FinishSubG92
END
SeqC RapidC ZCP3C EOL
END
END
RETURN
ProgStart:
InitProg
InitWFONum
SetFlood
SetFlagF('1') {not std sep sub Zreps in effect} {rep change 2}
SetFlag('3') {True = incrementing WFO numbers for MP. False = decrementing WFO numebrs for MP}
SetFlag('4') {True = toggle between incrementing/decrementing WFO's }
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
IF MultipleParts?
IF WorkFixtureOffsets?
IF LTEqual? MUL# Parts# NumOfCS# Num#('50')
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
' ( Not enough Work Fixture Offsets to handle this part. )' EOL
' ( Number of parts [ ' Parts# ' ] times CSs [ ' NumOfCS# ' ] )' EOL
' ( exceeds the machine limit. Switching to non-WFO style output. )' EOL
END
END
END
ELSE
IF LTEqual? NumOfCS# Num#('50') {****}
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
' ( Not enough Work Fixture Offsets to handle this part. )' EOL
' ( Number of CSs [ ' NumOfCS# ' ] exceeds the machine limit. )' EOL
' ( Switching to non-WFO style output. )' EOL
END
END
END
RETURN
InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
' ( ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
' ( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
' ( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
' ( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
' ( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
' ( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
' ( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
RETURN
FirstOp1:
Seq Plane CRCOff ' G80'
IF RigidTap?
' G95'
ELSE
' G94'
END
EOL
SeqC OpToolID EOL
SeqC ToolChng EOL
DoOpComments
DoPostScript
WFOStuff
G52Stuff
SeqC Speed SpinOn EOL
RETURN
FirstOp2:
CheckPass
IF AAxisAvail? OR BAxisAvail?
SeqC AbsOrInc Rapid CSAngleA CSAngleB EOL
SeqC StrtPos EOL
ELSE
SeqC AbsOrInc Rapid StrtPos EOL
END
RETURN
FirstOp3:
SeqC OfstOn CoolOn EOL
RETURN
NewToolOp1:
SeqC CoolOff EOL
SeqC ' G30 P1' EOL
RETURN
NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SeqC Rapid Home EOL
END
IF LAST ProgStop?
SeqC ' M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN
NewToolOp3: {Start new Operation}
Seq Plane CRCOff ' G80'
IF RigidTap?
' G95'
ELSE
' G94'
END
EOL
SeqC OpToolID EOL
SeqC ToolChng EOL
DoOpComments
DoPostScript
WFOStuff
G52Stuff
SeqC Speed SpinOn EOL
RETURN
NewToolOp4:
CheckPass
IF AAxisAvail? OR BAxisAvail?
SeqC AbsOrInc Rapid CSAngleA CSAngleB EOL
SeqC StrtPos EOL
ELSE
SeqC AbsOrInc Rapid StrtPos EOL
END
RETURN
NewToolOp5:
SeqC OfstOn CoolOn EOL
RETURN
SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC ' G30 P1' EOL
SeqC ' M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset? OR ChangeCS?
SeqC ' G30 P1' EOL
END
END
RETURN
SameToolOp2: {Start new Operation}
DoOpComments
DoPostScript
CheckPass
RETURN
SameToolOp3: {Start new Operation}
WFOStuff
G52Stuff
IF LAST ProgStop?
SeqC SpeedC SpinOn EOL
IF AAxisAvail? OR BAxisAvail?
SeqC PlaneC AbsOrInc Rapid CSAngleA CSAngleB EOL
SeqC StrtPos EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
END
SeqC OfstOn CoolOn EOL
ELSE
SeqC SpeedC EOL
IF AAxisAvail? OR BAxisAvail?
SeqC PlaneC AbsOrInc Rapid CSAngleA CSAngleB EOL
SeqC StrtPos EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
END
SeqC
IF NewToolOffset? OR ChangeCS?
OfstOn
END
IF NOT CoolOff? AND LAST CoolOff?
CoolOn
END
EOL
END
RETURN
End1:
SeqC CoolOff EOL
SeqC ' G30 P1' EOL
RETURN
End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {added FIRST modifier}
SeqC Rapid FirstHome EOL
END
IF Equal? CSOffsetA# Num#('0') AND Equal? CSOffsetB# Num#('0')
ELSE
SeqC
IF AAxisAvail?
CSAngleA
END
IF BAxisAvail?
CSAngleB
END
EOL
SeqC Preset
IF AAxisAvail?
' A0'
END
IF BAxisAvail?
' B0'
END
EOL
END
IF ProgStop?
SeqC ' M0' EOL
END
RETURN
End3:
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
' ( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
' ( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
' ( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN
MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
OpenMP
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
SubCSMP
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
IF ProgStop?
SeqC ' M0' EOL
ELSE
SeqC ProgStop EOL
END
CloseMP
End3
RETURN
MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
OpenMP
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
CloseMP
NewToolOp2 {to tool change, CS problem}
NewToolOp3
OpenMP
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
CloseMP
End2
End3
RETURN
MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
OpenMP
FirstOp2 {need StrtPos in Sub}
ELSE
IF NewTool?
CloseMP
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
NewToolOp5
OpenMP
NewToolOp4 {need StrtPos in Sub}
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
CloseMP {End of program}
End1
End2
End3
RETURN
NoMPs: {no multiple parts}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN
{Start of executable Prog, top level ****}
ProgStart {setup and initializations}
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
Wyszukiwarka
Podobne podstrony:
Okuma OSP 700M LH [AT] MV57 12 3Okuma OSP 700M LH [HIR] MW84 12Okuma OSP 700M [GTR] MW14 89 1Okuma OSP 700M [GTR] MW14 89 1Okuma OSP 5020M LH WMC CW69 12Okuma OSP 5020M LH WMC DW69 12Okuma OSP 5020M LH WMC BW69 12Okuma OSP 5020M C374 12Okuma OSP 5020 [MM] L806 85Okuma OSP 5000 (IPR) C261 12 1Okuma OSP 5020L [PB] L604 85 1Okuma OSP 500L GTR L290 82 2Okuma OSP 5000 LC10 L235 82 2Okuma OSP 5020M [GSI] M648 87Okuma OSP 500L G L237 85 2Okuma OSP 5020M M374 89 2Okuma OSP 5020L LNC 8C L499 85Okuma OSP 5020M [LC] MY37 89 1więcej podobnych podstron