IE RS lab 13 solutions


IEWB-RS Version 4.0 Solutions Guide Lab 13
1. Bridging and Switching
Task 1.1
The order of operations can simplify this task since by default all
inter-switch links are trunking. The commands below are applied in the
order shown.
SW1:
vtp domain CISCO
vtp pruning
vlan 2,5,6,7,10,11,24,25,32,43,367
!
interface FastEthernet0/1
switchport access vlan 11
!
interface FastEthernet0/3
switchport access vlan 367
!
interface FastEthernet0/5
switchport access vlan 5
SW2:
vtp domain CISCO
vtp mode client
!
interface FastEthernet0/2
switchport access vlan 2
!
interface FastEthernet0/4
switchport access vlan 43
!
interface FastEthernet0/6
switchport access vlan 6
!
interface FastEthernet0/15
switchport access vlan 7
!
interface FastEthernet0/24
switchport access vlan 32
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 1
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
SW3:
vtp domain CISCO
vtp mode client
!
interface FastEthernet0/3
switchport access vlan 32
!
interface FastEthernet0/5
switchport access vlan 25
!
interface FastEthernet0/24
switchport access vlan 43
!
interface Vlan11
ip address 139.1.11.254 255.255.255.0
SW4:
vtp domain CISCO
vtp mode client
!
interface FastEthernet0/4
switchport access vlan 24
!
interface FastEthernet0/6
switchport access vlan 367
!
interface FastEthernet0/17
switchport mode access
switchport access vlan 24
!
interface FastEthernet0/18
switchport mode access
switchport access vlan 25
!
interface Vlan2
ip address 139.1.2.22 255.255.255.0
Verify that the VLAN information has propagated through VTP prior to
changing the VTP modes.
Rack1SW1#show vtp status | include Domain|Pruning
VTP Domain Name : CISCO
VTP Pruning Mode : Enabled
Rack1SW1#show vlan brief | exclude unsup|^ |^1|active[ \t]+$
VLAN Name Status Ports
---- -------------------------------- --------- -----------------------
5 VLAN0005 active Fa0/5
367 VLAN0367 active Fa0/3
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 2
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1SW2#show vtp status | include Domain|Pruning
VTP Domain Name : CISCO
VTP Pruning Mode : Enabled
Rack1SW2#show vlan brief | exclude unsup|^ |^1|active[ \t]+$
VLAN Name Status Ports
---- -------------------------------- --------- -----------------------
2 VLAN0002 active Fa0/2
6 VLAN0006 active Fa0/6
7 VLAN0007 active Fa0/15
32 VLAN0032 active Fa0/24
43 VLAN0043 active Fa0/4
Rack1SW3#show vtp status | include Domain|Pruning
VTP Domain Name : CISCO
VTP Pruning Mode : Enabled
Rack1SW3#show vlan brief | exclude unsup|^ |^1|active[ \t]+$
VLAN Name Status Ports
---- -------------------------------- --------- -----------------------
25 VLAN0025 active Fa0/5
32 VLAN0032 active Fa0/3
43 VLAN0043 active Fa0/24
Rack1SW4#show vtp status | include Domain|Pruning
VTP Domain Name : CISCO
VTP Pruning Mode : Enabled
Rack1SW4#show vlan brief | exclude unsup|^ |^1|active[ \t]+$
VLAN Name Status Ports
---- -------------------------------- --------- -----------------------
24 VLAN0024 active Fa0/4, Fa0/17
25 VLAN0025 active Fa0/18
367 VLAN0367 active Fa0/6
Now that the VLAN information has propagated alter the VTP modes to
meet the requirements of the task.
SW2 and SW4:
vtp mode server
SW3:
vtp mode transparent
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 3
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 1.2
SW1 and SW2:
interface FastEthernet0/13
switchport trunk encapsulation dot1q
switchport trunk native vlan 11
switchport mode trunk
SW2 and SW3:
interface FastEthernet0/16
switchport trunk encapsulation dot1q
switchport trunk native vlan 11
switchport mode trunk
SW3 and SW4:
interface FastEthernet0/19
switchport trunk encapsulation dot1q
switchport trunk native vlan 11
switchport mode trunk
SW1:
interface range fa0/14, fa0/16  21
shutdown
SW2:
interface range fa0/14, fa0/17  19
shutdown
SW3:
interface range fa0/13 - 15, fa0/17  18, fa0/20 - 21
shutdown
SW4:
interface range fa0/13 - 16, fa0/20 - 21
shutdown
Strategy Tip
At this point of the lab a basic reachability test can be performed.
Task 1.2 Breakdown
After trying to perform a reachability test you may notice that connectivity
between R5 and SW2 is broken. The reason is that VLAN 25 was pruned
between SW3 and SW4. Since SW3 is in VTP transparent mode it does not
participate in VTP and will only pass on VTP pruning messages between the
other switches. In this design we need to ensure VLANs needed by SW3 are
never pruned on the trunk links to SW2 and SW4. See below:
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 4
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1R5#ping 139.1.58.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 139.1.58.8, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Rack1R5#
Rack1SW4#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1SW4(config)#interface fa0/19
Rack1SW4(config-if)#switchport trunk pruning vlan remove 25
Rack1SW4(config-if)#do show interface trunk
Port Mode Encapsulation Status Native vlan
Fa0/19 on 802.1q trunking 11
Port Vlans allowed on trunk
Fa0/19 1-4094
Port Vlans allowed and active in management domain
Fa0/19 1-2,5-7,10-11,24-25,32,43,367
Port Vlans in spanning tree forwarding state and not pruned
Fa0/19 1-2,5-7,11,25,32,43,367
Rack1SW4(config-if)#
Rack1R5#ping 139.1.58.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 139.1.58.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Rack1R5#
Task 1.2 Verification
Rack1SW1#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/13 on 802.1q trunking 11
Port Vlans allowed on trunk
Fa0/13 1-4094
Port Vlans allowed and active in management domain
Fa0/13 1-2,5-7,10-11,24-25,32,43,367
Port Vlans in spanning tree forwarding state and not pruned
Fa0/13 1-2,6-7,24-25,32,43,367
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 5
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1SW2#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/13 on 802.1q trunking 11
Fa0/16 on 802.1q trunking 11
Port Vlans allowed on trunk
Fa0/13 1-4094
Fa0/16 1-4094
Port Vlans allowed and active in management domain
Fa0/13 1-2,5-7,10-11,24-25,32,43,367
Fa0/16 1-2,5-7,10-11,24-25,32,43,367
Port Vlans in spanning tree forwarding state and not pruned
Fa0/13 1,5,11,367
Fa0/16 1,24-25,367
Rack1SW3#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/16 on 802.1q trunking 11
Fa0/19 on 802.1q trunking 11
Port Vlans allowed on trunk
Fa0/16 1-4094
Fa0/19 1-4094
Port Vlans allowed and active in management domain
Fa0/16 1-2,5-7,10-11,24-25,32,43,367
Fa0/19 1-2,5-7,10-11,24-25,32,43,367
Port Vlans in spanning tree forwarding state and not pruned
Fa0/16 1-2,5-7,10-11,24-25,32,43,367
Fa0/19 1-2,5-7,10-11,24-25,32,43,367
Rack1SW4#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/19 on 802.1q trunking 11
Port Vlans allowed on trunk
Fa0/19 1-4094
Port Vlans allowed and active in management domain
Fa0/19 1-2,5-7,10-11,24-25,32,43,367
Port Vlans in spanning tree forwarding state and not pruned
Fa0/19 1-2,5-7,11,25,32,43,367
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 6
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 1.3
SW2:
interface FastEthernet0/8
duplex full
speed 100
!
interface FastEthernet0/9
duplex full
speed 100
Task 1.3 Verification
Rack1SW2#show interfaces status | include Port|0/8|0/9
Port Name Status Vlan Duplex Speed Type
Fa0/8 notconnect 10 full 100 10/100BaseTX
Fa0/9 notconnect 10 full 100 10/100BaseTX
Task 1.4
SW1:
interface FastEthernet0/22
switchport voice vlan dot1p
Task 1.4 Verification
Rack1SW1#show interfaces fa0/22 switchport | include Voice
Voice VLAN: dot1p
Task 1.5
SW1 and SW2:
logging file flash:log.txt informational
Task 1.5 Verification
Rack1SW2#show logging
Syslog logging: enabled (0 messages dropped, 3 messages rate-limited, 0
flushes, 0 overruns, xml disabled, filtering disabled)
Console logging: level debugging, 58 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 60 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
File logging: file flash:log.txt,
max size 0, min size 0,
level informational, 1 messages logged
Trap logging: level informational, 63 message lines logged

Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 7
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
2. Frame Relay
Task 2.1
Quick Note
R1:
Although it s not required
interface Serial0/0
to shutdown the interfaces
shutdown
before configuration is
encapsulation frame-relay
applied it is a good
no frame-relay inverse-arp
practice for lab scenarios
frame-relay map ip 139.1.15.5 105 broadcast
no shutdown
R2:
interface Serial0/0
shutdown
encapsulation frame-relay
no frame-relay inverse-arp
frame-relay map ip 139.1.25.5 205 broadcast
no shutdown
R5:
interface Serial0/0
Quick Note
encapsulation frame-relay
See task 4.5 breakdown
!
for why point-to-point
interface Serial0/0.501 point-to-point
interfaces are used
ip address 139.1.15.5 255.255.255.0
frame-relay interface-dlci 501
!
interface Serial0/0.502 point-to-point
ip address 139.1.25.5 255.255.255.0
frame-relay interface-dlci 502
Task 2.1 Verification
Rack1R2#show frame-relay map
Serial0/0 (up): ip 139.1.25.5 dlci 205(0xCD,0x30D0), static,
broadcast,
CISCO, status defined, active
Rack1R1#show frame-relay map
Serial0/0 (up): ip 139.1.15.5 dlci 105(0x69,0x1890), static,
broadcast,
CISCO, status defined, active
Rack1R5#show frame map
Serial0/0.502 (up): point-to-point dlci, dlci 502(0x1F6,0x7C60),
broadcast
status defined, active
Serial0/0.501 (up): point-to-point dlci, dlci 501(0x1F5,0x7C50),
broadcast
status defined, active
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 8
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1R5#ping 139.1.25.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 139.1.25.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms
Rack1R5#ping 139.1.15.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 139.1.15.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms
Task 2.2
R6:
interface Serial0/0/0
shutdown
encapsulation frame-relay
frame-relay map ip 54.1.2.254 100 broadcast
no frame-relay inverse-arp
no shutdown
Task 2.2 Verification
Rack1R6#show frame-relay map
Serial0/0/0 (up): ip 54.1.2.254 dlci 100(0x64,0x1840), static,
broadcast,
IETF, status defined, active
Rack1R6#ping 54.1.2.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 54.1.2.254, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms
Task 2.3
R4:
interface Serial0/1
ip address negotiated
encapsulation ppp
R5:
interface Serial0/1
encapsulation ppp
peer default ip address dhcp
clockrate 64000
!
ip dhcp-server 139.1.11.100
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 9
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Tasks 2.3 & 9.1 Verification
This task should be verified in conjunction with task 9.1. Apply Task
9.1 solution in order to perform complete verification. In order for
reachability for verification of this task at this point of the lab
static routes maybe applied and then removed after verification. The
preferred option at this point of the lab would be to temporarily
hardcode R4 s IP address. Then after full IP reachability has been
obtained R4 s IP address can be learned dynamically. If you use this
option be sure to write down what workaround you have put in place so
that later in the lab you will be sure to come back to solve the task
correctly.
Enable debugging:
Rack1R4#debug ppp negotiation
PPP protocol negotiation debugging is on
Rack1R5#debug dhcp
DHCP client activity debugging is on
Rack1R1#debug ip dhcp server events
Rack1R4(config)#interface s0/1
Rack1R4(config-if)#shutdown
Rack1R4(config-if)#no shutdown
Se0/1 PPP: Outbound cdp packet dropped
Se0/1 PPP: Outbound cdp packet dropped
Se0/1 PPP: Outbound cdp packet dropped
%LINK-3-UPDOWN: Interface Serial0/1, changed state to up
Se0/1 PPP: Using default call direction
Se0/1 PPP: Treating connection as a dedicated line
Se0/1 PPP: Session handle[3E000009] Session id[6]
Se0/1 PPP: Phase is ESTABLISHING, Active Open
Se0/1 LCP: O CONFREQ [Closed] id 6 len 10
Se0/1 LCP: MagicNumber 0x30A1E593 (0x050630A1E593)
Se0/1 LCP: I CONFREQ [REQsent] id 6 len 10
Se0/1 LCP: MagicNumber 0x07F9584E (0x050607F9584E)
Se0/1 LCP: O CONFACK [REQsent] id 6 len 10
Se0/1 LCP: MagicNumber 0x07F9584E (0x050607F9584E)
Se0/1 LCP: I CONFACK [ACKsent] id 6 len 10
Se0/1 LCP: MagicNumber 0x30A1E593 (0x050630A1E593)
Se0/1 LCP: State is Open
Se0/1 PPP: Phase is FORWARDING, Attempting Forward
Se0/1 PPP: Phase is ESTABLISHING, Finish LCP
Se0/1 PPP: Phase is UP
Se0/1 IPCP: O CONFREQ [Closed] id 1 len 10
Se0/1 IPCP: Address 0.0.0.0 (0x030600000000)
Se0/1 CDPCP: O CONFREQ [Closed] id 1 len 4
Se0/1 PPP: Process pending ncp packets
Se0/1 IPCP: I CONFREQ [REQsent] id 1 len 10
Se0/1 IPCP: Address 139.1.45.5 (0x03068B012D05)
Se0/1 IPCP: O CONFACK [REQsent] id 1 len 10
Se0/1 IPCP: Address 139.1.45.5 (0x03068B012D05)
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 10
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Se0/1 CDPCP: I CONFREQ [REQsent] id 1 len 4
Se0/1 CDPCP: O CONFACK [REQsent] id 1 len 4
Se0/1 CDPCP: I CONFACK [ACKsent] id 1 len 4
Se0/1 CDPCP: State is Open
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed
state to up
Se0/1 IPCP: I CONFREQ [ACKsent] id 2 len 10
Se0/1 IPCP: Address 139.1.45.5 (0x03068B012D05)
Se0/1 IPCP: O CONFACK [ACKsent] id 2 len 10
Se0/1 IPCP: Address 139.1.45.5 (0x03068B012D05)
Se0/1 IPCP: TIMEout: State ACKsent
Se0/1 IPCP: O CONFREQ [ACKsent] id 2 len 10
Se0/1 IPCP: Address 0.0.0.0 (0x030600000000)
Se0/1 IPCP: I CONFNAK [ACKsent] id 1 len 10
Se0/1 IPCP: Address 139.1.45.4 (0x03068B012D04)
Se0/1 IPCP: ID 1 didn't match 2, discarding packet
Se0/1 IPCP: I CONFNAK [ACKsent] id 2 len 10
Se0/1 IPCP: Address 139.1.45.4 (0x03068B012D04)
Se0/1 IPCP: O CONFREQ [ACKsent] id 3 len 10
Se0/1 IPCP: Address 139.1.45.4 (0x03068B012D04)
Se0/1 IPCP: I CONFACK [ACKsent] id 3 len 10
Se0/1 IPCP: Address 139.1.45.4 (0x03068B012D04)Se0/1 IPCP: State is
Open
Se0/1 IPCP: Install negotiated IP interface address 139.1.45.4
Se0/1 IPCP: Install route to 139.1.45.5
Se0/1 IPCP: Add link info for cef entry 139.1.45.5
Rack1R4#show ip interface s0/1
Serial0/1 is up, line protocol is up
Internet address is 139.1.45.4/32
Broadcast address is 255.255.255.255
Address determined by IPCP
Peer address is 139.1.45.5

Rack1R5#
%LINK-3-UPDOWN: Interface Serial0/1, changed state to up
DHCP: proxy allocate request
DHCP: new entry. add to queue, interface
DHCP: SDiscover attempt # 1 for entry:
DHCP: SDiscover: sending 292 byte length DHCP packet
DHCP: SDiscover 292 bytes
DHCP: XID MATCH in dhcpc_for_us()
DHCP: Received a BOOTREP pkt
DHCP: offer received from 139.1.15.1
DHCP: SRequest attempt # 1 for entry:
DHCP: SRequest- Server ID option: 139.1.15.1
DHCP: SRequest- Requested IP addr option: 139.1.45.4
DHCP: SRequest placed lease len option: 86400
DHCP: SRequest: 310 bytes
DHCP: SRequest: 310 bytes
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed
state to up
DHCP: SRequest attempt # 2 for entry:
DHCP: SRequest- Server ID option: 139.1.15.1
DHCP: SRequest- Requested IP addr option: 139.1.45.4
DHCP: SRequest placed lease len option: 86400
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 11
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
DHCP: SRequest: 310 bytes
DHCP: SRequest: 310 bytes
DHCP: XID MATCH in dhcpc_for_us()
DHCP: Received a BOOTREP pkt
DHCP Proxy Client Pooling: ***Allocated IP address: 139.1.45.4
Rack1R1#
DHCPD: assigned IP address 139.1.45.4 to client
0063.6973.636f.2d31.3339.2e31.2e34.352e.352d.5365.7269.616c.302f.31.
Rack1R1#show ip dhcp binding
Bindings from all pools not associated with VRF:
IP address Client-ID/ Lease expiration
Type
Hardware address/
User name
139.1.45.4 0063.6973.636f.2d31. Mar 02 1993 01:24 AM
Automatic
3339.2e31.2e34.352e.
352d.5365.7269.616c.
302f.31
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 12
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
3. Interior Gateway Routing
Task 3.1
R3:
key chain RIP
key 1
key-string CISCO
!
interface Ethernet0/1
ip rip authentication mode md5
ip rip authentication key-chain RIP
!
router rip
version 2
network 192.10.1.0
Task 3.1 Verification
Verify RIP configuration:
Rack1R3#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 2, receive version 2
Interface Send Recv Triggered RIP Key-chain
Ethernet0/1 2 2 RIP
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
192.10.1.0
Routing Information Sources:
Gateway Distance Last Update
192.10.1.254 120 00:00:09
Distance: (default is 120)
Verify RIP routes:
Rack1R3#show ip route rip
R 222.22.2.0/24 [120/7] via 192.10.1.254, 00:00:06, Ethernet0/1
R 220.20.3.0/24 [120/7] via 192.10.1.254, 00:00:06, Ethernet0/1
R 205.90.31.0/24 [120/7] via 192.10.1.254, 00:00:06, Ethernet0/1
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 13
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 3.2
R4:
router rip
version 2
no validate-update-source
redistribute connected metric 1 route-map CONNECTED->RIP
network 139.1.0.0
network 150.1.0.0
no auto-summary
!
route-map CONNECTED->RIP permit 10
match interface Ethernet0/0
R5:
router rip
version 2
network 139.1.0.0
network 150.1.0.0
no auto-summary
SW2:
ip routing
!
router rip
version 2
network 139.1.0.0
network 150.1.0.0
no auto-summary
Task 3.2 Verification
Rack1R4#show ip route rip
139.1.0.0/16 is variably subnetted, 8 subnets, 2 masks
R 139.1.15.0/24 [120/1] via 139.1.45.5, 00:00:24
R 139.1.5.0/24 [120/1] via 139.1.45.5, 00:00:24
R 139.1.25.0/24 [120/1] via 139.1.45.5, 00:00:24
R 139.1.45.0/24 [120/2] via 139.1.48.8, 00:00:28, Ethernet0/1
R 139.1.58.0/24 [120/1] via 139.1.48.8, 00:00:28, Ethernet0/1
[120/1] via 139.1.45.5, 00:00:24
150.1.0.0/24 is subnetted, 3 subnets
R 150.1.5.0 [120/1] via 139.1.45.5, 00:00:24
R 150.1.8.0 [120/1] via 139.1.48.8, 00:00:28, Ethernet0/1
Rack1R5#show ip route rip
R 204.12.1.0/24 [120/1] via 139.1.45.4, 00:00:28, Serial0/1
139.1.0.0/16 is variably subnetted, 7 subnets, 2 masks
R 139.1.48.0/24 [120/1] via 139.1.58.8, 00:00:20, Ethernet0/1
[120/1] via 139.1.45.4, 00:00:28, Serial0/1
150.1.0.0/24 is subnetted, 3 subnets
R 150.1.4.0 [120/1] via 139.1.45.4, 00:00:28, Serial0/1
R 150.1.8.0 [120/1] via 139.1.58.8, 00:00:20, Ethernet0/1
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 14
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 3.3
R4:
router rip
offset-list 0 in 1 Serial0/1
R5:
router rip
default-information originate
Task 3.3 Verification
Verify the RIP routes on R4 before the offset-list is applied:
Rack1R4#show ip route rip
139.1.0.0/16 is variably subnetted, 8 subnets, 2 masks
R 139.1.15.0/24 [120/1] via 139.1.45.5, 00:00:26
R 139.1.5.0/24 [120/1] via 139.1.45.5, 00:00:26
R 139.1.25.0/24 [120/1] via 139.1.45.5, 00:00:26
R 139.1.45.0/24 [120/2] via 139.1.48.8, 00:00:19, Ethernet0/1
R 139.1.58.0/24 [120/1] via 139.1.48.8, 00:00:19, Ethernet0/1
[120/1] via 139.1.45.5, 00:00:26
150.1.0.0/24 is subnetted, 3 subnets
R 150.1.5.0 [120/1] via 139.1.45.5, 00:00:26
R 150.1.8.0 [120/1] via 139.1.48.8, 00:00:19, Ethernet0/1
R* 0.0.0.0/0 [120/1] via 139.1.45.5, 00:00:26
Apply offset list and verify the routes again:
Rack1R4#show ip route rip
139.1.0.0/16 is variably subnetted, 8 subnets, 2 masks
R 139.1.15.0/24 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:26
R 139.1.5.0/24 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:26
R 139.1.25.0/24 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:26
R 139.1.45.0/24 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
R 139.1.58.0/24 [120/1] via 139.1.48.8, 00:00:15, Ethernet0/1
150.1.0.0/24 is subnetted, 3 subnets
R 150.1.5.0 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:26
R 150.1.8.0 [120/1] via 139.1.48.8, 00:00:15, Ethernet0/1
R* 0.0.0.0/0 [120/2] via 139.1.48.8, 00:00:15, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:26
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 15
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 3.4
R4, R5, and SW2:
router rip
timers basic 3 18 18 24
Task 3.4 Breakdown
RIP convergence time is dependent on the update and flush timers. The lower
the flush timer is, the sooner the route will be removed out of the table if an
update has not been received about it. Under normal circumstances, the age of
a prefix will be reset every update timer. In this case, the flush time for the prefix
should never be reached. When an update is not received, it is typically due to a
lost routing path. In this case the route is cleared out of the table when the age
reaches the flush.
To change these timers, issue the timers basic RIP process subcommand. The
default RIP timers are hello 30, invalid 180, hold down 180, and flush 240. To
view these timers values, issue the show ip protocols command.
Task 3.4 Verification
Rack1SW2# show ip protocols | include Sending|Invalid
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 27 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Rack1SW2#show ip protocols | include Sending|Invalid
Sending updates every 3 seconds, next due in 1 seconds
Invalid after 18 seconds, hold down 18, flushed after 24
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 16
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 3.5
R1:
interface Serial0/0
ip ospf network point-to-point
!
router ospf 1
router-id 150.1.1.1
network 139.1.15.1 0.0.0.0 area 1
network 150.1.1.1 0.0.0.0 area 1
R2:
interface Serial0/0
ip ospf network point-to-point
!
router ospf 1
network 139.1.25.2 0.0.0.0 area 1
network 150.1.2.2 0.0.0.0 area 1
R5:
router ospf 1
router-id 150.1.5.5
network 139.1.15.5 0.0.0.0 area 1
network 139.1.25.5 0.0.0.0 area 1
Task 3.5 Verification
Rack1R5#show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
150.1.2.2 0 FULL/ - 00:00:36 139.1.25.2 Serial0/0.502
150.1.1.1 0 FULL/ - 00:00:32 139.1.15.1 Serial0/0.501
Verify OSPF network type for instance on R1:
Rack1R1#show ip ospf interface s0/0
Serial0/0 is up, line protocol is up
Internet Address 139.1.15.1/24, Area 1
Process ID 1, Router ID 150.1.1.1, Network Type POINT_TO_POINT, Cost:
64
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
oob-resync timeout 40
Hello due in 00:00:06
Index 1/1, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 150.1.5.5
Suppress hello for 0 neighbor(s)
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 17
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Verify the OSPF routes:
Rack1R5#show ip route ospf
150.1.0.0/16 is variably subnetted, 5 subnets, 2 masks
O 150.1.2.2/32 [110/65] via 139.1.25.2, 00:02:06, Serial0/0.502
O 150.1.1.1/32 [110/65] via 139.1.15.1, 00:02:06, Serial0/0.501
Rack1R1#show ip route ospf
139.1.0.0/16 is variably subnetted, 4 subnets, 2 masks
O 139.1.25.0/24 [110/128] via 139.1.15.5, 00:02:18, Serial0/0
150.1.0.0/16 is variably subnetted, 2 subnets, 2 masks
O 150.1.2.2/32 [110/129] via 139.1.15.5, 00:02:18, Serial0/0
Task 3.6
R1:
router ospf 1
network 139.1.11.1 0.0.0.0 area 0
network 139.1.13.1 0.0.0.0 area 0
R2:
router ospf 1
network 139.1.2.2 0.0.0.0 area 0
network 139.1.23.2 0.0.0.0 area 0
R3:
interface Serial1/2
clockrate 64000
!
interface Serial1/3
clockrate 64000
!
router ospf 1
router-id 150.1.3.3
network 139.1.0.3 0.0.0.0 area 0
network 139.1.13.3 0.0.0.0 area 0
network 139.1.23.3 0.0.0.0 area 0
network 150.1.3.3 0.0.0.0 area 1
R6:
interface GigabitEthernet0/1
ip ospf priority 0
!
router ospf 1
router-id 150.1.6.6
network 139.1.0.6 0.0.0.0 area 0
network 139.1.6.6 0.0.0.0 area 0
network 150.1.6.6 0.0.0.0 area 1
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 18
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
SW1:
ip routing
!
interface Vlan367
ip ospf priority 0
!
router ospf 1
router-id 150.1.7.7
network 139.1.0.7 0.0.0.0 area 0
network 139.1.7.7 0.0.0.0 area 0
network 150.1.7.7 0.0.0.0 area 1
Task 3.6 Verification
Rack1R3#show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
150.1.2.2 0 FULL/ - 00:00:31 139.1.23.2 Serial1/3
150.1.1.1 0 FULL/ - 00:00:31 139.1.13.1 Serial1/2
150.1.6.6 0 FULL/DROTHER 00:00:38 139.1.0.6 Ethernet0/0
150.1.7.7 0 FULL/DROTHER 00:00:35 139.1.0.7 Ethernet0/0
Verify again that R3 is the DR on VLAN367:
Rack1R3#show ip ospf interface e0/0
Ethernet0/0 is up, line protocol is up
Internet Address 139.1.0.3/24, Area 0
Process ID 1, Router ID 150.1.3.3, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 150.1.3.3, Interface address 139.1.0.3
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
oob-resync timeout 40
Hello due in 00:00:08
Supports Link-local Signaling (LLS)
Index 1/1, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 2
Last flood scan time is 0 msec, maximum is 4 msec
Neighbor Count is 2, Adjacent neighbor count is 2
Adjacent with neighbor 150.1.6.6
Adjacent with neighbor 150.1.7.7
Suppress hello for 0 neighbor(s)
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 19
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Verify the OSPF routes:
Rack1R3#show ip route ospf
139.1.0.0/24 is subnetted, 9 subnets
O 139.1.11.0 [110/782] via 139.1.13.1, 00:02:03, Serial1/2
O IA 139.1.15.0 [110/845] via 139.1.13.1, 00:02:03, Serial1/2
O 139.1.2.0 [110/782] via 139.1.23.2, 00:02:03, Serial1/3
O 139.1.6.0 [110/11] via 139.1.0.6, 00:02:03, Ethernet0/0
O 139.1.7.0 [110/11] via 139.1.0.7, 00:02:03, Ethernet0/0
O IA 139.1.25.0 [110/845] via 139.1.23.2, 00:02:03, Serial1/3
150.1.0.0/16 is variably subnetted, 5 subnets, 2 masks
O IA 150.1.7.7/32 [110/11] via 139.1.0.7, 00:02:03, Ethernet0/0
O IA 150.1.6.6/32 [110/11] via 139.1.0.6, 00:02:03, Ethernet0/0
O IA 150.1.2.2/32 [110/782] via 139.1.23.2, 00:02:03, Serial1/3
O IA 150.1.1.1/32 [110/782] via 139.1.13.1, 00:02:03, Serial1/2
Task 3.7
R5:
router ospf 1
distance 109 150.1.1.1 0.0.0.0 VIA_R1
!
ip access-list standard VIA_R1
permit 139.1.11.0
permit 139.1.2.0
permit 139.1.0.0
permit 139.1.6.0
permit 139.1.7.0
Task 3.7 Verification
Verify new distance for the selected prefixes:
Rack1R5#show ip route ospf | include 109
O IA 139.1.11.0/24 [109/65] via 139.1.15.1, 00:00:11, Serial0/0.501
O IA 139.1.2.0/24 [109/910] via 139.1.15.1, 00:00:11, Serial0/0.501
O IA 139.1.0.0/24 [109/138] via 139.1.15.1, 00:00:11, Serial0/0.501
O IA 139.1.6.0/24 [109/139] via 139.1.15.1, 00:00:11, Serial0/0.501
O IA 139.1.7.0/24 [109/139] via 139.1.15.1, 00:00:11, Serial0/0.501
Check that backup routes exist:
Rack1R5(config)#interface s0/0.501
Rack1R5(config-subif)#shutdown
%OSPF-5-ADJCHG: Process 1, Nbr 150.1.1.1 on Serial0/0.501 from FULL to
DOWN, Neighbor Down: Interface down or detached
Rack1R5(config-subif)#do show ip route ospf
139.1.0.0/16 is variably subnetted, 14 subnets, 2 masks
O IA 139.1.11.0/24 [110/910] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 139.1.15.0/24 [110/973] via 139.1.25.2, 00:00:04, Serial0/0.502
O IA 139.1.13.0/24 [110/909] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 139.1.2.0/24 [110/65] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 139.1.0.0/24 [110/138] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 139.1.6.0/24 [110/139] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 139.1.7.0/24 [110/139] via 139.1.25.2, 00:00:05, Serial0/0.502
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 20
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
O IA 139.1.23.0/24 [110/128] via 139.1.25.2, 00:00:05, Serial0/0.502
150.1.0.0/16 is variably subnetted, 8 subnets, 2 masks
O IA 150.1.7.7/32 [110/139] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 150.1.6.6/32 [110/139] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 150.1.3.3/32 [110/129] via 139.1.25.2, 00:00:05, Serial0/0.502
O 150.1.2.2/32 [110/65] via 139.1.25.2, 00:00:05, Serial0/0.502
O IA 150.1.1.1/32 [110/910] via 139.1.25.2, 00:00:05, Serial0/0.502
Task 3.8
R3:
router ospf 1
redistribute rip subnets
!
router rip
redistribute ospf 1 metric 1
auto-summary
R5:
router ospf 1
redistribute rip subnets
Task 3.8 Verification
Verify that R3 send thes minimum required routing information to BB2:
Rack1R3#debug ip rip
RIP protocol debugging is on
Rack1R3#
RIP: sending v2 update to 224.0.0.9 via Ethernet0/1 (192.10.1.3)
RIP: build update entries
139.1.0.0/16 via 0.0.0.0, metric 1, tag 0
150.1.0.0/16 via 0.0.0.0, metric 1, tag 0
204.12.1.0/24 via 0.0.0.0, metric 1, tag 0
Finally to ensure you have full internal connectivity run the following
TCL script:
foreach i {
139.1.2.2
139.1.25.2
150.1.2.2
139.1.23.2
139.1.13.3
139.1.0.3
150.1.3.3
139.1.23.3
192.10.1.3
150.1.4.4
139.1.45.4
139.1.48.4
139.1.15.5
139.1.5.5
139.1.25.5
150.1.5.5
139.1.45.5
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 21
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
139.1.58.5
139.1.6.6
139.1.0.6
150.1.6.6
139.1.7.7
139.1.0.7
150.1.7.7
150.1.8.8
139.1.48.8
139.1.58.8
139.1.11.254
139.1.2.22
} { puts [ exec "ping $i" ] }
Note that the Frame Relay link between R6 and BB1 is omitted from
connectivity test.
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 22
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
4. Multicast
Task 4.1
R2:
ip multicast-routing
!
interface Serial0/0
ip pim dense-mode
!
interface Serial0/1
ip pim dense-mode
!
interface FastEthernet0/0
ip pim dense-mode
R3:
ip multicast-routing
!
interface Serial1/3
ip pim dense-mode
!
interface Ethernet0/0
ip pim dense-mode
!
R5:
ip multicast-routing
!
interface Ethernet0/0
ip pim dense-mode
!
interface Serial0/0.502
ip pim dense-mode
Task 4.1 Verification
Verify PIM interfaces and neighbors:
Rack1R5#show ip pim interface
Address Interface Ver/ Nbr Query DR DR
Mode Count Intvl Prior
139.1.5.5 Ethernet0/0 v2/D 0 30 1 139.1.5.5
139.1.25.5 Serial0/0.502 v2/D 1 30 1 0.0.0.0
Rack1R5#show ip pim neig
PIM Neighbor Table
Neighbor Interface Uptime/Expires Ver DR
Address
Prio/Mode
139.1.25.2 Serial0/0.502 00:01:10/00:01:33 v2 1 / S
Rack1R2#show ip pim interface
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 23
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Address Interface Ver/ Nbr Query DR DR
Mode Count Intvl Prior
139.1.2.2 FastEthernet0 v2/D 0 30 1 139.1.2.2
139.1.25.2 Serial0/0 v2/D 1 30 1 139.1.25.5
139.1.23.2 Serial0/1 v2/D 1 30 1 0.0.0.0
Rack1R2#show ip pim neig
PIM Neighbor Table
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
139.1.25.5 Serial0/0 00:03:14/00:01:27 v2 1 / DR S
139.1.23.3 Serial0/1 00:03:28/00:01:43 v2 1 / S
Rack1R3#show ip pim interface
Address Interface Ver/ Nbr Query DR DR
Mode Count Intvl Prior
139.1.23.3 Serial1/3 v2/D 1 30 1 0.0.0.0
139.1.0.3 Ethernet0/0 v2/D 0 30 1 139.1.0.3
Rack1R3#show ip pim neighbor
PIM Neighbor Table
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
139.1.23.2 Serial1/3 00:05:21/00:01:18 v2 1 / S
Task 4.2
R3:
interface Tunnel35
ip unnumbered Ethernet0/0
ip pim dense-mode
tunnel source Loopback0
tunnel destination 150.1.5.5
R5:
interface Tunnel35
ip unnumbered Ethernet0/0
ip pim dense-mode
tunnel source Loopback0
tunnel destination 150.1.3.3
!
ip mroute 0.0.0.0 0.0.0.0 Tunnel35
Task 4.2 Breakdown
The above scenario uses a GRE tunnel to tunnel multicast traffic across non-PIM
speaking neighbors. As the tunnel interface is based on the loopback interfaces
of R3 and R5, R1 (the non-PIM speaking device) only sees unicast GRE traffic
between these loopback interfaces. Therefore as long as the transit devices
have unicast reachability throughout the network, they can be used to transport
multicast traffic.
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 24
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 4.2 Verification
Join multicast groups 239.2.2.2 with R2 FastEthernet0/0 and 239.5.5.5
with R5 Ethernet 0/0:
R2:
interface FastEthernet0/0
ip igmp join-group 239.2.2.2
R5:
interface Ethernet0/0
ip igmp join-group 239.5.5.5
Enable mpacket debugging at R3:
Rack1R3#debug ip mpacket
IP multicast packets debugging is on
Simulate multicast traffic from R6 to 239.2.2.2
Rack1R6#ping 239.2.2.2 repeat 6
Type escape sequence to abort.
Sending 6, 100-byte ICMP Echos to 239.2.2.2, timeout is 2 seconds:
Reply to request 0 from 139.1.23.2, 32 ms
Reply to request 1 from 139.1.23.2, 32 ms
Reply to request 2 from 139.1.23.2, 32 ms
Reply to request 3 from 139.1.23.2, 32 ms
Reply to request 4 from 139.1.23.2, 32 ms
Reply to request 5 from 139.1.23.2, 36 ms
Look at R3 s debugging output:
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=22,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=23,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=24,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=25,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=26,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.2.2.2 (Serial1/3) id=27,
ttl=254, prot=1, len=100(100), mforward
Rack1R3#show ip mroute
IP Multicast Routing Table
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 25
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C -
Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP
Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.2.2.2), 00:04:59/stopped, RP 0.0.0.0, flags: D
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Tunnel35, Forward/Dense, 00:04:59/00:00:00
Serial1/3, Forward/Dense, 00:04:59/00:00:00
(139.1.0.6, 239.2.2.2), 00:01:26/00:02:38, flags: T
Incoming interface: Ethernet0/0, RPF nbr 0.0.0.0
Outgoing interface list:
Serial1/3, Forward/Dense, 00:01:27/00:00:00
Tunnel35, Prune/Dense, 00:01:27/00:01:32
(*, 224.0.1.40), 00:20:35/stopped, RP 0.0.0.0, flags: DCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Tunnel35, Forward/Dense, 00:13:52/00:00:00
Serial1/3, Forward/Dense, 00:20:35/00:00:00
Next, enable additional debugging at R3, and send multicast traffic
from R6 to 239.5.5.5:
Rack1R6#ping 239.5.5.5 repeat 6
Type escape sequence to abort.
Sending 6, 100-byte ICMP Echos to 239.5.5.5, timeout is 2 seconds:
Reply to request 0 from 139.1.5.5, 68 ms
Reply to request 1 from 139.1.5.5, 68 ms
Reply to request 2 from 139.1.5.5, 80 ms
Reply to request 3 from 139.1.5.5, 68 ms
Reply to request 4 from 139.1.5.5, 68 ms
Reply to request 5 from 139.1.5.5, 88 ms
Rack1R3#debug ip packet detail 100
IP packet debugging is on (detailed) for access list 100
Note how GRE traffic is load balanced.
Rack1R3#
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=46, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/2), len 124, sending,
proto=47
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 26
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=47, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/2), len 124, sending,
proto=47
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=48, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/3), len 124, sending,
proto=47
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=49, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/2), len 124, sending,
proto=47
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=50, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/3), len 124, sending,
proto=47
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/2), len 78, sending,
proto=47
IP(0): s=139.1.0.6 (Ethernet0/0) d=239.5.5.5 (Tunnel35) id=51, ttl=254,
prot=1, len=100(100), mforward
IP: s=150.1.3.3 (Tunnel35), d=150.1.5.5 (Serial1/3), len 124, sending,
proto=47
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 27
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
5. IPv6
Task 5.1
R2:
ipv6 unicast-routing
!
interface FastEthernet0/0
ipv6 address 2001:CC1E:1:2::/64 eui-64
!
interface Serial0/1
ipv6 address 2001:CC1E:1:23::2/127
R3:
ipv6 unicast-routing
!
interface Ethernet0/0
ipv6 address 2001:CC1E:1::/64 eui-64
!
interface Ethernet0/1
ipv6 address 2001:192:10:1::/64 eui-64
!
interface Serial1/3
ipv6 address 2001:CC1E:1:23::3/127
R6:
ipv6 unicast-routing
!
ipv6 unicast-routing
!
interface GigabitEthernet0/0
ipv6 address 2001:CC1E:1::/64 eui-64
Task 5.2
R6:
interface Serial0/0/0
ipv6 address 2001:54:1:2::6/64
frame-relay map ipv6 2001:54:1:2::254 100 broadcast
Tasks 5.1  5.2 Verification
Verify IPv6 address assignment:
Rack1R6#show ipv6 interface brief
GigabitEthernet0/0 [up/up]
FE80::215:62FF:FED0:4830
2001:CC1E:1:0:215:62FF:FED0:4830
GigabitEthernet0/1 [up/up]
unassigned
Serial0/0/0 [up/up]
unassigned
Loopback0 [up/up]
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 28
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
unassigned
Rack1R3#show ipv6 interface brief
Ethernet0/0 [up/up]
FE80::250:73FF:FE1C:7761
2001:CC1E:1:0:250:73FF:FE1C:7761
Ethernet0/1 [up/up]
FE80::250:73FF:FE1C:7762
2001:192:10:1:250:73FF:FE1C:7762
Serial1/0 [administratively down/down]
unassigned
Serial1/1 [administratively down/down]
unassigned
Serial1/2 [up/up]
unassigned
Serial1/3 [up/up]
FE80::250:73FF:FE1C:7761
2001:CC1E:1:23::3
Loopback0 [up/up]
unassigned
Tunnel35 [up/up]
unassigned
Rack1R2#show ipv6 interface brief
FastEthernet0/0 [up/up]
FE80::204:27FF:FEB5:2F60
2001:CC1E:1:2:204:27FF:FEB5:2F60
Serial0/0 [up/up]
unassigned
Serial0/1 [up/up]
FE80::204:27FF:FEB5:2F60
2001:CC1E:1:23::2
Virtual-Access1 [up/up]
unassigned
Loopback0 [up/up]
Unassigned
Test basic connectivity:
Rack1R3#ping 2001:CC1E:1:0:215:62FF:FED0:4830
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:CC1E:1:0:215:62FF:FED0:4830,
timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/2/4 ms
Rack1R3#ping 2001:CC1E:1:23::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:CC1E:1:23::2, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms
Check Frame-Relay mapping at R6 and test connectivity:
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 29
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1R6#show frame-relay map
Serial0/0/0 (up): ipv6 2001:54:1:2::254 dlci 100(0x64,0x1840), static,
broadcast,
IETF, status defined, active
Serial0/0/0 (up): ip 54.1.2.254 dlci 100(0x64,0x1840), static,
broadcast,
IETF, status defined, active
Rack1R6#ping 2001:54:1:2::254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:54:1:2::254, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/32/36 ms
Task 5.3
R2:
interface FastEthernet0/0
ipv6 rip RIPng enable
!
interface Serial0/1
ipv6 rip RIPng enable
R3:
interface Ethernet0/0
ipv6 rip RIPng enable
!
interface Ethernet0/1
ipv6 rip RIPng enable
ipv6 rip RIPng metric-offset 13
!
interface Serial1/3
ipv6 rip RIPng enable
R6:
interface GigabitEthernet0/0
ipv6 rip RIPng enable
!
interface Serial0/0/0
ipv6 rip RIPng enable
frame-relay map ipv6 FE80::254 100
ipv6 rip RIPng metric-offset 13
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 30
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 5.3 Verification
Verify the RIP routes on R6 and R3 (note the metric value of 15):
Rack1R6#show ipv6 route rip
IPv6 Routing Table - 16 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS
summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF
ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
R 2001:192:10:1::/64 [120/2]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
R 2001:205:90:31::/64 [120/15]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
R 2001:220:20:3::/64 [120/15]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
R 2001:222:22:2::/64 [120/15]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
R 2001:254:0:112::/64 [120/14]
via FE80::254, Serial0/0/0
R 2001:254:0:113::/64 [120/14]
via FE80::254, Serial0/0/0
R 2001:254:0:114::/64 [120/14]
via FE80::254, Serial0/0/0
R 2001:254:0:115::/96 [120/14]
via FE80::254, Serial0/0/0
R 2001:CC1E:1:2::/64 [120/3]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
R 2001:CC1E:1:23::2/127 [120/2]
via FE80::250:73FF:FE1C:7761, GigabitEthernet0/0
Rack1R3#show ipv6 route rip
IPv6 Routing Table - 17 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS
summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF
ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
R 2001:54:1:2::/64 [120/2]
via FE80::215:62FF:FED0:4830, Ethernet0/0
R 2001:205:90:31::/64 [120/14]
via FE80::260:70FF:FE15:AC7A, Ethernet0/1
R 2001:220:20:3::/64 [120/14]
via FE80::260:70FF:FE15:AC7A, Ethernet0/1
R 2001:222:22:2::/64 [120/14]
via FE80::260:70FF:FE15:AC7A, Ethernet0/1
R 2001:254:0:112::/64 [120/15]
via FE80::215:62FF:FED0:4830, Ethernet0/0
R 2001:254:0:113::/64 [120/15]
via FE80::215:62FF:FED0:4830, Ethernet0/0
R 2001:254:0:114::/64 [120/15]
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 31
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
via FE80::215:62FF:FED0:4830, Ethernet0/0
R 2001:254:0:115::/96 [120/15]
via FE80::215:62FF:FED0:4830, Ethernet0/0
R 2001:CC1E:1:2::/64 [120/2]
via FE80::204:27FF:FEB5:2F60, Serial1/3
Task 5.4
R6:
interface GigabitEthernet0/1
ipv6 address 2001:CC1E:1:6::/64 eui-64
ipv6 nd ra-interval 60
ipv6 nd ra-lifetime 180
ipv6 rip RIPng enable
Task 5.4 Verification
Verify IPv6 ND RA configuration:
Rack1R6#show ipv6 interface gigabitEthernet 0/1
GigabitEthernet0/1 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::215:62FF:FED0:4831
Global unicast address(es):
2001:CC1E:1:6:215:62FF:FED0:4831, subnet is 2001:CC1E:1:6::/64
[EUI]
Joined group address(es):
FF02::1
FF02::2
FF02::9
FF02::1:FFD0:4831
MTU is 1500 bytes
ICMP error messages limited to one every 100 milliseconds
ICMP redirects are enabled
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND advertised reachable time is 0 milliseconds
ND advertised retransmit interval is 0 milliseconds
ND router advertisements are sent every 60 seconds
ND router advertisements live for 180 seconds
Hosts use stateless autoconfig for addresses.
Verify prefix advertisement:
Rack1R3#show ipv6 route 2001:CC1E:1:6::
IPv6 Routing Table - 18 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS
summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF
ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
R 2001:CC1E:1:6::/64 [120/2]
via FE80::215:62FF:FED0:4830, Ethernet0/0
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 32
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
6. QoS
Task 6.1
R2:
ip cef
!
class-map match-all ICMP
match protocol icmp
class-map match-all UDP
match access-group 101
class-map match-all TCP
match access-group 102
!
policy-map MQC_CAR
class ICMP
drop
class UDP
police cir 128000 bc 2000
conform-action transmit
exceed-action set-prec-transmit 0
class TCP
police cir 256000 bc 4000
conform-action transmit
exceed-action set-prec-transmit 0
!
interface FastEthernet0/0
service-policy input MQC_CAR
!
access-list 101 permit udp any any
access-list 102 permit tcp any any
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 33
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 6.2
R5:
class-map match-all HTTP_RESPONSES
match access-group name HTTP_RESPONSES
!
!
policy-map DLCI_501
class HTTP_RESPONSES
bandwidth percent 80
!
interface Serial0/0
frame-relay traffic-shaping
!
interface Serial0/0.501 point-to-point
frame-relay class DLCI_501
!
ip access-list extended HTTP_RESPONSES
permit tcp any eq www 139.1.11.0 0.0.0.255
!
map-class frame-relay DLCI_501
frame-relay cir 384000
frame-relay mincir 384000
service-policy output DLCI_501
Task 6.2 Verification
Verify the policy configuration:
Rack1R5#show frame-relay pvc 501
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 501, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
Serial0/0.501
input pkts 2353 output pkts 5770 in bytes 213730
out bytes 1786756 dropped pkts 7 in pkts dropped 7
out pkts dropped 0 out bytes dropped 0
in FECN pkts 0 in BECN pkts 0 out FECN pkts 0
out BECN pkts 0 in DE pkts 0 out DE pkts 0
out bcast pkts 5504 out bcast bytes 1727736
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 1000 bits/sec, 0 packets/sec
pvc create time 03:40:46, last time pvc status changed 03:40:46
cir 384000 bc 384000 be 0 byte limit 6000 interval
125
mincir 384000 byte increment 6000 Adaptive Shaping none
pkts 112 bytes 41576 pkts delayed 0 bytes delayed 0
shaping inactive
traffic shaping drops 0
service policy DLCI_501
Serial0/0.501: DLCI 501 -
Service-policy output: DLCI_501
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 34
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Class-map: HTTP_RESPONSES (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name HTTP_RESPONSES
Queueing
Output Queue: Conversation 41
Bandwidth 80 (%)
Bandwidth 307 (kbps) Max Threshold 64 (packets)
(pkts matched/bytes matched) 0/0
(depth/total drops/no-buffer drops) 0/0/0
Class-map: class-default (match-any)
109 packets, 40580 bytes
5 minute offered rate 1000 bps, drop rate 0 bps
Match: any
Output queue size 0/max total 600/drops 0
Task 6.3
R1:
map-class frame-relay DLCI_105
frame-relay cir 512000
frame-relay bc 5120
frame-relay fragment 640
!
interface Serial0/0
frame-relay traffic-shaping
frame-relay class DLCI_105
R5:
interface Serial0/0.502 point-to-point
frame-relay class DLCI_502
!
map-class frame-relay DLCI_501
frame-relay cir 512000
frame-relay bc 5120
frame-relay fragment 640
!
map-class frame-relay DLCI_502
frame-relay cir 512000
frame-relay mincir 128000
Task 6.3 Verification
Verify the Frame-Relay PVC shaping parameters:
Rack1R5#show frame-relay pvc 501 | begin fragment type
fragment type end-to-end fragment size 640
cir 512000 bc 5120 be 0 limit 640 interval 10
mincir 384000 byte increment 640 BECN response no IF_CONG no
frags 261 bytes 97278 frags delayed 0 bytes delayed 0
shaping inactive
traffic shaping drops 0
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 35
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1R5#show frame-relay pvc 502 | begin cir
cir 512000 bc 512000 be 0 byte limit 8000 interval 125
mincir 128000 byte increment 8000 Adaptive Shaping none
pkts 577 bytes 223590 pkts delayed 2 bytes delayed 166
shaping inactive
traffic shaping drops 0
Queueing strategy: fifo
Output queue 0/40, 0 drop, 0 dequeued
Rack1R1#show frame-relay pvc 105 | begin fragment type
fragment type end-to-end fragment size 640
cir 512000 bc 5120 be 0 limit 640 interval 10
mincir 256000 byte increment 640 BECN response no IF_CONG no
frags 56 bytes 5070 frags delayed 0 bytes delayed 0
shaping inactive
traffic shaping drops 0
Task 6.4
R3:
interface Ethernet0/0
ip policy route-map POLICY_ROUTING
!
ip access-list extended FROM_VLAN_367_TO_VLAN_43
permit ip 139.1.0.0 0.0.0.255 204.12.1.0 0.0.0.255
!
route-map POLICY_ROUTING permit 10
match ip address FROM_VLAN_367_TO_VLAN_43
match length 1251 1500
set ip next-hop 139.1.23.2
!
route-map POLICY_ROUTING deny 20
description Don't policy-route anything else
R5:
interface Ethernet0/1
ip policy route-map POLICY_ROUTING
!
interface Serial0/1
ip policy route-map POLICY_ROUTING
!
ip access-list extended FROM_VLAN_43_TO_VLAN_367
permit ip 204.12.1.0 0.0.0.255 139.1.0.0 0.0.0.255
!
route-map POLICY_ROUTING permit 10
match ip address FROM_VLAN_43_TO_VLAN_367
match length 1251 1500
set ip next-hop 139.1.25.2
!
route-map POLICY_ROUTING deny 20
description Don't policy-route anything else
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 36
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 6.4 Verification
Generate packets of different sizes from R6 to BB3 and then enable
policy route debugging at R3:
Rack1R3#debug ip policy
Policy routing debugging is on
Rack1R3#
Rack1R6#ping 204.12.1.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 204.12.1.254, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 88/91/92 ms
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
rejected(deny) - normal forwarding
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
rejected(deny) - normal forwarding
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 100, FIB policy
rejected(deny) - normal forwarding
Rack1R6#ping 204.12.1.254 size 1300
Type escape sequence to abort.
Sending 5, 1300-byte ICMP Echos to 204.12.1.254, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
1008/1018/1060 ms
Rack1R3#
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 1300, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, g=139.1.23.2, len 1300,
FIB policy routed
Rack1R3#
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 1300, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, g=139.1.23.2, len 1300,
FIB policy routed
Rack1R3#
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 1300, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, g=139.1.23.2, len 1300,
FIB policy routed
Rack1R3#
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 1300, FIB policy
match
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 37
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, g=139.1.23.2, len 1300,
FIB policy routed
Rack1R3#
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, len 1300, FIB policy
match
IP: s=139.1.0.6 (Ethernet0/0), d=204.12.1.254, g=139.1.23.2, len 1300,
FIB policy routed
Task 6.5
R5:
map-class frame-relay DLCI_502
frame-relay cir 512000
frame-relay bc 5120
frame-relay fragment 640
frame-relay ip rtp priority 16384 16383 512
R2:
interface Serial0/0
frame-relay traffic-shaping
frame-relay class DLCI_205
!
map-class frame-relay DLCI_205
frame-relay cir 512000
frame-relay bc 5120
frame-relay fragment 640
frame-relay ip rtp priority 16384 16383 512
Task 6.5 Verification
Verify the VoIP QoS configuration:
Rack1R5#show frame-relay pvc 502 | include Queueing|fragment|rtp
Queueing strategy: weighted fair
fragment type end-to-end fragment size 640
ip rtp priority parameters 16384 32767 512000
Rack1R2#show frame-relay pvc 205| include Queueing|fragment|rtp
Queueing strategy: weighted fair
fragment type end-to-end fragment size 640
ip rtp priority parameters 16384 32767 512000
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 38
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
7. Security
Task 7.1
R3:
interface Ethernet0/1
ip access-group FILTER_IN in
ip access-group FILTER_OUT out
no ip unreachables
!
ip access-list extended FILTER_IN
deny icmp any any echo log
permit ip any any
!
ip access-list extended FILTER_OUT
deny icmp any any time-exceeded log
deny icmp any any port-unreachable log
permit ip any any
R4:
interface Ethernet0/0
ip access-group FILTER_IN in
ip access-group FILTER_OUT out
no ip unreachables
!
ip access-list extended FILTER_IN
deny icmp any any echo log
permit ip any any
!
ip access-list extended FILTER_OUT
deny icmp any any time-exceeded log
deny icmp any any port-unreachable log
permit ip any any
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 39
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
8. System Management
Task 8.1
R4:
snmp-server enable traps bgp
snmp-server host 139.1.2.100 CISCOBGP
Task 8.2
R3 and R4:
logging 139.1.5.100
logging facility local6
Task 8.3
R6:
interface GigabitEthernet0/1
ip nbar protocol-discovery
Task 8.3 Verification
To see how NBAR collects statistics temporarily enable NBAR on
interfaces GigabitEthernet 0/0:
Rack1R6#show ip nbar protocol-discovery interface g0/0 top-n 3
GigabitEthernet0/0
Input Output
----- ------
Protocol Packet Count Packet Count
Byte Count Byte Count
5min Bit Rate (bps) 5min Bit Rate (bps)
5min Max Bit Rate (bps) 5min Max Bit Rate (bps)
------------------- ------------------------ -----------------------
icmp 200 0
22800 0
0 0
0 0
ospf 23 10
2298 1040
0 0
0 0
bgp 4 0
266 0
0 0
0 0
unknown 0 0
0 0
0 0
0 0
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 40
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Total 227 10
25364 1040
0 0
0 0
9. IP Services
Task 9.1
R1:
ip dhcp excluded-address 139.1.45.0 139.1.45.3
ip dhcp excluded-address 139.1.45.5 139.1.45.255
!
ip dhcp pool R4
Quick Note
network 139.1.45.0 255.255.255.0
Task states that installed
server is not valid. Use R1
R5:
instead.
no ip dhcp-server 139.1.11.100
ip dhcp-server 139.1.15.1
Task 9.2
R1:
ip dhcp excluded-address 139.1.3.0 139.1.3.99
ip dhcp excluded-address 139.1.3.201 139.1.3.255
!
ip dhcp pool VLAN_367
network 139.1.0.0 255.255.255.0
default-router 139.1.0.1
domain-name InternetworkExpert.com
lease infinite
!
R3:
!
interface Ethernet0/0
standby 1 name HSRP
ip helper-address 139.1.13.1 redundancy HSRP
standby 1 ip 139.1.0.1
standby 1 preempt
R6:
interface GigabitEthernet0/0
standby 1 name HSRP
ip helper-address 139.1.13.1 redundancy HSRP
standby 1 ip 139.1.0.1
standby 1 priority 101
standby 1 preempt
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 41
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 9.2 Verification
Verify the standby configuration:
Rack1R6#show standby
GigabitEthernet0/0 - Group 1
State is Active
1 state change, last state change 00:04:38
Virtual IP address is 139.1.0.1
Active virtual MAC address is 0000.0c07.ac01
Local virtual MAC address is 0000.0c07.ac01 (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.048 secs
Preemption enabled
Active router is local
Standby router is 139.1.0.3, priority 100 (expires in 8.052 sec)
Priority 101 (configured 101)
IP redundancy name is "hsrp-Gi0/0-1" (default)
Verify DHCP address assignment and the redundancy configuration:
Use SW2 to simulate a host in VLAN367:
Rack1SW2(config)#interface vl367
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan367, changed state
to up
Rack1SW2(config-if)#ip address dhcp
Rack1SW2(config-if)#
DHCP: DHCP client process started: 10
RAC: Starting DHCP discover on Vlan367
DHCP: Try 1 to acquire address for Vlan367
DHCP: allocate request
DHCP: new entry. add to queue
DHCP: SDiscover attempt # 1 for entry:
DHCP: SDiscover: sending 300 byte length DHCP packet
DHCP: SDiscover 300 bytes
B'cast on Vlan367 interface from 0.0.0.0
DHCP: SDiscover attempt # 2 for entry:
DHCP: SDiscover: sending 300 byte length DHCP packet
DHCP: SDiscover 300 bytes
B'cast on Vlan367 interface from 0.0.0.0
DHCP: Received a BOOTREP pkt
DHCP: offer received from 139.1.13.1
DHCP: SRequest attempt # 1 for entry:
DHCP: SRequest- Server ID option: 139.1.13.1
DHCP: SRequest- Requested IP addr option: 139.1.0.2
DHCP: SRequest placed lease len option: 4294967295
DHCP: SRequest: 318 bytes
DHCP: SRequest: 318 bytes
B'cast on Vlan367 interface from 0.0.0.0
DHCP: Received a BOOTREP pkt
DHCP: offer received from 139.1.13.1
DHCP: offer received in bad state: Requesting punt
DHCP: Received a BOOTREP pkt
DHCP: offer received from 139.1.13.1
DHCP: offer received in bad state: Requesting punt
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 42
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
DHCP: Received a BOOTREP pkt
DHCP: offer received from 139.1.13.1
DHCP: offer received in bad state: Requesting punt
DHCP: Received a BOOTREP pkt
Interface Vlan367 assigned DHCP address 139.1.0.2, mask 255.255.255.0
DHCP Client Pooling: ***Allocated IP address: 139.1.0.2
DHCP: Received a BOOTREP pkt
DHCP: rcv ack in Bound state: punt
Allocated IP address = 139.1.0.2 255.255.255.0
Rack1R1#show ip dhcp binding
Bindings from all pools not associated with VRF:
IP address Client-ID/ Lease expiration
Type
Hardware address/
User name
139.1.0.2 0063.6973.636f.2d30. Infinite
Automatic
3030.662e.3866.6232.
2e65.3830.302d.566c.
3336.37
139.1.45.4 0063.6973.636f.2d31. Mar 02 1993 01:24 AM
Automatic
3339.2e31.2e34.352e.
352d.5365.7269.616c.
302f.31
Rack1R6(config)#interface g0/0
Rack1R6(config-if)#shutdown
Rack1R3#show standby
Ethernet0/0 - Group 1
State is Active
5 state changes, last state change 00:00:18
Virtual IP address is 139.1.0.1
Active virtual MAC address is 0000.0c07.ac01
Local virtual MAC address is 0000.0c07.ac01 (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 2.412 secs
Preemption enabled
Active router is local
Standby router is unknown
Priority 100 (default 100)
IP redundancy name is "hsrp-Et0/0-1" (default)
Rack1SW2#ping 139.1.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 139.1.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 43
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
10. Exterior Gateway Routing
Task 10.1
R4:
router bgp 100
synchronization
bgp router-id 150.1.4.4
neighbor 150.1.6.6 remote-as 100
neighbor 150.1.6.6 update-source Loopback0
neighbor 150.1.6.6 next-hop-self
neighbor 204.12.1.254 remote-as 54
R6:
router bgp 100
syncronization
bgp router-id 150.1.6.6
neighbor 54.1.2.254 remote-as 54
neighbor 150.1.4.4 remote-as 100
neighbor 150.1.4.4 update-source Loopback0
neighbor 150.1.4.4 next-hop-self
Task 10.1 Verification
Verify BGP neighbors:
Rack1R6#show ip bgp summary | begin Neighbor
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
54.1.2.254 4 54 8 4 11 0 0 00:00:50 10
150.1.4.4 4 100 7 7 11 0 0 00:00:49 10
Rack1R4#show ip bgp summary | begin Neighbor
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
150.1.6.6 4 100 8 8 11 0 0 00:01:20 10
204.12.1.254 4 54 9 5 11 0 0 00:01:37 10
Task 10.2
R4:
router bgp 100
redistribute rip route-map IGP_TO_BGP
aggregate-address 139.1.0.0 255.255.0.0 summary-only
neighbor 204.12.1.254 unsuppress-map IGP_TO_BGP
distribute-list prefix DENY_AGGREGATE in
!
ip prefix-list DENY_AGGREGATE seq 5 deny 139.1.0.0/16
ip prefix-list DENY_AGGREGATE seq 10 permit 0.0.0.0/0 le 32
!
ip prefix-list VLAN_5 seq 5 permit 139.1.5.0/24
!
route-map IGP_TO_BGP permit 10
match ip address prefix-list VLAN_5
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 44
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
R6:
router bgp 100
network 139.1.6.0 mask 255.255.255.0
aggregate-address 139.1.0.0 255.255.0.0 summary-only
Task 10.2 Verification
Check routes, that R4 and R6 advertise to BB3:
Rack1R4#show ip bgp neighbors 204.12.1.254 advertised-routes
BGP table version is 15, local router ID is 150.1.4.4
Status codes: s suppressed, d damped, h history, * valid, > best, i -
internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
r> 139.1.0.0 0.0.0.0 32768 i
s> 139.1.5.0/24 139.1.45.5 2 32768 ?
Rack1R6#show ip bgp neighbors 54.1.2.254 advertised-routes
BGP table version is 14, local router ID is 150.1.6.6
Status codes: s suppressed, d damped, h history, * valid, > best, i -
internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 139.1.0.0 0.0.0.0 32768 i
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 45
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Task 10.3
R4:
router rip
redistribute bgp 100 metric 1 route-map PERMIT_ODD
!
router bgp 100
bgp router-id 150.1.5.5
neighbor 204.12.1.254 route-map PERMIT_ODD in
!
ip access-list standard ODD
permit 1.0.0.0 254.255.255.255
!
route-map PERMIT_ODD permit 10
match ip address ODD
R5:
router rip
redistribute ospf 1 metric 1 route-map OSPF_TO_RIP
!
route-map OSPF_TO_RIP permit 10
match tag 6
R6:
router ospf 1
redistribute bgp 100 subnets tag 6 route-map PERMIT_EVEN
!
router bgp 100
neighbor 54.1.2.254 route-map PERMIT_EVEN in
!
ip access-list standard EVEN
permit 0.0.0.0 254.255.255.255
!
route-map PERMIT_EVEN permit 10
match ip address EVEN
Task 10.3 Breakdown
The BGP synchronization rule states that all iBGP learned routes must have a
match in the IGP table in order to be considered for BGP best path selection.
Although the BGP synchronization rule is rarely enabled in a production BGP
environment, and is effectively considered legacy now, the problem that it was
designed to prevent is still valid.
BGP synchronization is designed to prevent the case when non BGP speaking
devices are in the transit path of the iBGP network. Since these transit devices
are not running BGP, they must have an IGP route in order to send traffic to the
final destination. Therefore, the BGP synchronization process first checks the
IGP table to see if there is a match for all iBGP learned prefixes. If there are
equal IGP matches in the IP routing table, synchronization has occurred, and the
iBGP learned prefix can be considered for best path selection. However, if there
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 46
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
is no matching IGP prefix for the iBGP prefix, synchronization has not occurred,
and the iBGP learned prefix cannot be considered for best path selection.
In the above scenario, BGP synchronization is enabled on R4. Therefore any
iBGP learned prefixes on R4 must have matching IGP routes in order to be
considered valid. Therefore, BGP prefixes must be injected into the IGP domain
in order for this case to occur.
There is an additional issue with OSPF. When you turn synchronization on, and
redistribute BGP prefixes into OSPF, you should make sure that OSPF ASBR
Router ID matches originating BGP Router ID. This is why we set Router ID of
R4 to 150.1.5.5.
Task 10.3 Verification
Verify that R4 accepts only odd first octet prefixes from BB3:
Rack1R4#show ip bgp neighbors 204.12.1.254 routes
BGP table version is 21, local router ID is 150.1.4.4
Status codes: s suppressed, d damped, h history, * valid, > best, i -
internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 113.0.0.0 204.12.1.254 0 54 50 60 i
*> 115.0.0.0 204.12.1.254 0 54 i
*> 117.0.0.0 204.12.1.254 0 54 i
*> 119.0.0.0 204.12.1.254 0 54 i
Confirm that R6 accepts only prefixes with even first octet from BB1:
Rack1R6#show ip bgp neighbors 54.1.2.254 routes
BGP table version is 18, local router ID is 150.1.6.6
Status codes: s suppressed, d damped, h history, * valid, > best, i -
internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 28.119.16.0/24 54.1.2.254 0 54 i
*> 28.119.17.0/24 54.1.2.254 0 54 i
*> 112.0.0.0 54.1.2.254 0 0 54 50 60 i
*> 114.0.0.0 54.1.2.254 0 0 54 i
*> 116.0.0.0 54.1.2.254 0 0 54 i
*> 118.0.0.0 54.1.2.254 0 0 54 i
Next verify the BGP redistribution:
Rack1R4#show ip route rip
R 118.0.0.0/8 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 116.0.0.0/8 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 47
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
139.1.0.0/16 is variably subnetted, 8 subnets, 2 masks
R 139.1.15.0/24 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 139.1.5.0/24 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 139.1.25.0/24 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 139.1.45.0/24 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
R 139.1.58.0/24 [120/1] via 139.1.48.8, 00:00:01, Ethernet0/1
R 114.0.0.0/8 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 112.0.0.0/8 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
28.0.0.0/24 is subnetted, 2 subnets
R 28.119.17.0 [120/2] via 139.1.48.8, 00:00:02, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:01
R 28.119.16.0 [120/2] via 139.1.48.8, 00:00:02, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:01
150.1.0.0/24 is subnetted, 3 subnets
R 150.1.5.0 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
R 150.1.8.0 [120/1] via 139.1.48.8, 00:00:01, Ethernet0/1
R* 0.0.0.0/0 [120/2] via 139.1.48.8, 00:00:01, Ethernet0/1
[120/2] via 139.1.45.5, 00:00:00
Rack1R6#show ip route ospf | include E2
O E2 119.0.0.0/8 [110/20] via 139.1.0.3, 00:04:58, GigabitEthernet0/0
O E2 222.22.2.0/24 [110/20] via 139.1.0.3, 00:05:01, GigabitEthernet0/0
O E2 204.12.1.0/24 [110/20] via 139.1.0.3, 00:05:01, GigabitEthernet0/0
O E2 117.0.0.0/8 [110/20] via 139.1.0.3, 00:04:58, GigabitEthernet0/0
O E2 220.20.3.0/24 [110/20] via 139.1.0.3, 00:05:01, GigabitEthernet0/0
O E2 139.1.5.0/24 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 139.1.45.4/32 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 139.1.45.0/24 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 139.1.58.0/24 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 139.1.48.0/24 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 115.0.0.0/8 [110/20] via 139.1.0.3, 00:04:58, GigabitEthernet0/0
O E2 113.0.0.0/8 [110/20] via 139.1.0.3, 00:04:58, GigabitEthernet0/0
O E2 192.10.1.0/24 [110/20] via 139.1.0.3, 00:05:01, GigabitEthernet0/0
O E2 150.1.5.0/24 [110/20] via 139.1.0.3, 00:05:01,
GigabitEthernet0/0
O E2 150.1.4.0/24 [110/20] via 139.1.0.3, 00:05:03,
GigabitEthernet0/0
O E2 150.1.8.0/24 [110/20] via 139.1.0.3, 00:05:03,
GigabitEthernet0/0
O E2 205.90.31.0/24 [110/20] via 139.1.0.3, 00:05:03,
GigabitEthernet0/0
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 48
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Verify BGP synchronization:
Rack1R6#show ip bgp 115.0.0.0
BGP routing table entry for 115.0.0.0/8, version 22
Paths: (1 available, best #1, table Default-IP-Routing-Table, RIB-
failure(17))
Advertised to update-groups:
2
54
150.1.4.4 (metric 20) from 150.1.4.4 (150.1.5.5)
Origin IGP, metric 0, localpref 100, valid, internal,
synchronized, best
Rack1R4#show ip bgp 116.0.0.0
BGP routing table entry for 116.0.0.0/8, version 16
Paths: (1 available, best #1, table Default-IP-Routing-Table, RIB-
failure(17))
Advertised to update-groups:
1
54
150.1.6.6 (metric 2) from 150.1.6.6 (150.1.6.6)
Origin IGP, metric 0, localpref 100, valid, internal,
synchronized, best
Make a final verification by tracerouting to even numbered routes from
R4 and odd from R6:
Rack1R4#traceroute 116.0.0.1
Type escape sequence to abort.
Tracing the route to 116.0.0.1
1 139.1.48.8 4 msec
139.1.45.5 16 msec
139.1.48.8 8 msec
2 139.1.25.2 28 msec
139.1.58.5 12 msec
139.1.25.2 32 msec
3 139.1.25.2 24 msec
139.1.23.3 44 msec
139.1.25.2 28 msec
4 139.1.0.6 44 msec
139.1.23.3 36 msec
139.1.0.6 40 msec
5 139.1.0.6 40 msec
54.1.2.254 60 msec
139.1.0.6 40 msec
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 49
-
IEWB-RS Version 4.0 Solutions Guide Lab 13
Rack1R6#traceroute 115.0.0.1
Type escape sequence to abort.
Tracing the route to 115.0.0.1
1 139.1.0.3 4 msec 0 msec 0 msec
2 139.1.23.2 16 msec 16 msec 12 msec
3 139.1.25.5 32 msec 32 msec 28 msec
4 139.1.45.4 44 msec 40 msec 44 msec
5 204.12.1.254 44 msec 44 msec 44 msec
6 172.16.4.1 36 msec * 32 msec
Task 10.4
R4:
router bgp 100
neighbor 204.12.1.254 maximum-prefix 150000 90
R6:
router bgp 100
neighbor 54.1.2.254 maximum-prefix 150000 90
Task 10.4 Breakdown
Large fluctuations in the BGP table can cause devices with limited amounts of
memory to crash. These fluctuations usually occur either due to a
misconfiguration, or a malicious attack on the BGP table. In order to prevent
such as fluctuation from occurring, the maximum-prefix option on the BGP
neighbor statement can be used to configure a threshold of received routes at
which a BGP session will be reset.
Task 10.4 Verification
Rack1R6#show ip bgp neighbors 54.1.2.254 | begin Maximum prefixes
Maximum prefixes allowed 150000
Threshold for warning message 90%
Number of NLRIs in the update sent: max 3, min 0

Rack1R4#show ip bgp neighbors 204.12.1.254 | begin Maximum prefixes
Maximum prefixes allowed 150000
Threshold for warning message 90%
Number of NLRIs in the update sent: max 0, min 0

Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
13 - 50
-


Wyszukiwarka

Podobne podstrony:
IE RS lab 14 solutions
IE RS lab 13 overview
IE RS lab 11 solutions
IE RS lab 12 solutions
IE RS lab 10 solutions
IE RS lab 13 Diagram
IE RS lab 9 solutions
IE RS lab 9 overview
IE RS lab 19 overview
IE RS lab 18 Diagram
IE RS lab 17 diagram
IE RS lab 8 diagram
IE RS lab 18 overview
IE RS lab 10 diagram
IE RS lab 10 overview
IE RS lab 12 overview
IE RS lab 16 diagram
IE RS lab 14 diagram

więcej podobnych podstron