{Change Comments ***********************************************************}
{added separate sub call code and warning for not separate, 7/5/88 WFG}
{separate sub calls turned off in this post- 'UseSeparateSubCalls' commented out}
{ncPost3ż24 or better}
{added IF ToolChangeAtHome?, & SetHome 9/26/88 WFG}
{added PostScript commands 3/11/89 WFG}
{added PostScript command comments 5/9/89, WFG, use ncPost 3.10Ś9 or better}
{removed run time comments, 5/9/89, WFG}
{added "must be all capital letters when typed in" to Postscript Command comment, 5/17/89, JR}
{added metric, 6/5/89, WFG}
{suppressed first cycle StrtPos for sep subs,7/17/89 WFG}
{last tool now goes to FirstHome when finished, 7/26/89, WFG}
{changed to Sep Sub standard}
{.65, corrected Sep sub problem if 1st cut <> Z step, 9/14/89 WFG, requires ncPost 3.19Ś5}
{.66, added name comment to Prog ID # line, 10/30/89, WFG}
{.67, new prog commands, 11/20/89, WFG}
{*.68, AutoCycles and 3.2 support, 12/4/89, WFG (Good luck on the upgrades to other posts)}
{.69, corrected 2 repeat op/autocycle problems, 12/21/89, WFG}
{1/8/90-2/7/90
Changes to M001.69
Moved DoPostScript command to very beginning of NewTool & SameTool op's, same as FirstOp.
Deleted last line of NewWFO PostScript comment, it no longer applies.
Move DoEndOpPS command in NewTool & end of prog to end of operation outside of Full-up MP.
Restucture to have M01 or M00 in New Tool.
Deleted ProgStop? from end of prog, not neccesary.
Check for ProgStop at beginning AND end of operation does not work, it comes out both places,
only using for end of operation. Reflected in PSComments.
Deleted StopProg sub.
Re-wrote SameTool section for many reasons.
Deleted ClearancePlane3# prog format it is no longer needed.
New sub CheckPass to replace statement in main for SetPass.
Modified WFOStuff sub to include SameTool.
Deleted StrtPos from OpenMP sub and added to main where needed.
Updated to .70 format.
Jim Radcliffe}
{.71.1, added InitProg, 4/11/90, JR}
{.71.2, FIRST modifier, no CRCOffC in AutoCycCutSub2, add Connect for ZOnlyRep, 4/23/90, JR}
{.72.1, New PS subs, formats, CoolOff?, ProgStop to start of NewTool & SameTool, 5/23/90, JR}
{.72.2, modified subroutine stuff (same effect), 7/1/90, DWB}
{.73, Replaced SetSRXYZero with SetSRXYtoSP, CoolOff, new formaters, 7/24/90, DWB}
{.74, ResetCRCNum, modified PostScript comments, 8/1/90, JR}
{.76, corrected AutoCycle SP and EP Status Record errors}
{.76.2, removed beginning Op ProgStop capability and Get Coolant, 2/6/91, WFG}
{2/15/91,
Updated to new 4.0 Version Fanuc 6M M001.80:
Added Coolant checking for SameTool.
Added ProgStop checking for final Operation.
DWB}
{5/17/91, M001.80.01 added drill Z's, WFG}
{9/13/91,
Modified Fanuc 6M M001.80.01:
Added IF FIFO? for Milling.
Added TrackZNO# ZDepth# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
DWB}
{10/01/91
Copied & Modified: Fanuc 6M M001.81
For: Applied Fusion Inc.
Deleted IF UseComments? AND ProgramNameComment? for program header.
Added: SeqC '/' IncValue ' G30 X0 Z0' EOL
SeqC '/' 'G28 B0' EOL
SeqC '/' ToolChng '0' EOL
To FirstOp.
Added PreTool.
Added SAFE restart line (SeqC Rapid AbsOrInc Plane CRCOff OfstOff DrillOff 'G98' WFO1 Speed SpinOn EOL)
to every operation.
Moved the CoolantOn before the offset line.
Turned the spindle and coolant off after the "I" plane.
Added ' G28 Y0' to the : SeqC IncValue OfstOff EOL line.
Changed the OfstOff Code from G28 to G49 in form.
Kim Michelman}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '########;0'
#6 = '####^###;'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
{Prog Subroutines **********************************************************}
DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
END
RETURN
PSInit: {reset flags}
NewWFOF
RotateF
RETURN
PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# 'M10' EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# 'M11' EOL
FifthCCWF {reset flag}
END
RETURN
DoPostScript:
PSInit
EachPS
SeqC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN
StartSub:
OpenSub
SubID EOL
DoSubComment
RETURN
SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN
StdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
StartSub
RETURN
FinishSub1: {part 1}
UnSkipZ
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedRateC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN
FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN
OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqC SetWFO EOL
SeqC SubCall CallLab RepLab OnePart EOL
IncWFO
NextWFO
ELSE
SeqC SubCall CallLab RepLab Parts EOL
END
StartSub
RETURN
CloseMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
SeqC WFO1 EOL
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC CRCOnC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
RETURN
ToolPath:
ResetCRCNum {.72}
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF LastFeat? AND AutoCycle? {.70}
SeqC CRCOffC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RETURN
WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
ELSE
SeqC 'G' NewWFO# EOL
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
SeqC 'G' NewWFO# EOL
END
END
END
RETURN
AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqC IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
ToolPath
IF Repeats? AND FeedConnect? AND ZshiftOnly?
SeqC AbsOrInc EOL {.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO? {.81}
SeqC AbsOrInc FeedC ZCP2 FeedRateC EOL
ELSE
SeqC AbsOrInc RapidC ZCP2 EOL {.71.2 removed CRCOffC, gets turned off in ToolPath}
END
END
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN
AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN
Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN
G92Sub:
SubWarning
StdSub
SeqC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN
ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
IF FeedConnect?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqC Rapid ZCP2PlusInc EOL {.69 added Rapid, reads better}
{can't call for cycle = 1, .69 changed to ZCP2PlusInc}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL {.69 added Rapid, reads better}
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC SubCall CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
IF FIFO? {.81}
SeqC Feed ZCP2 FeedRate EOL {.69}
ELSE
SeqC Rapid ZCP2 EOL {.69}
END
END {.69}
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN
ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqC SubCall CallLab EOL
NextCycle
StartSub
SkipZ
ToolPath
FinishSub1
SeqC EndSub EOL
CloseSub
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
GetStartOfSameTool:
Seq ' ' EOL
DoOpComments
DoPostScript
SeqC Rapid AbsOrInc Plane CRCOff OfstOff DrillOff 'G98' WFO1 Speed SpinOn EOL
WFOStuff
CheckPass
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls ('50')
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
ProgID1 '( ' ProgramName$ ' )' EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
SeqC AbsOrInc Plane CRCOff OfstOff DrillOff 'G98' WFO1 EOL
SeqC 'M11' EOL
SeqC '/' IncValue ' G30 X0 Z0' EOL
SeqC '/' 'G28 B0' EOL
SeqC '/' ToolChng '0' EOL
SeqC AbsOrInc ' G0 B0' EOL
SeqC 'M10' EOL
SeqC PreTool EOL
Seq ' ' EOL
DoOpComments
SeqC Rapid AbsOrInc Plane CRCOff OfstOff DrillOff 'G98' WFO1 Speed SpinOn EOL
DoPostScript
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC CoolOn EOL
SeqC OfstOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF NewTool?
{Finish off last Operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqC SpinOff CoolOff EOL
SeqC IncValue OfstOff ' G28 Y0' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF ToolChangeAtHome?
SeqC AbsOrInc Rapid Home EOL
END
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
SeqC ProgStop EOL
END
{Start new Operation}
SeqC ToolChng EOL
SeqC PreTool EOL
SeqC Plane 'G80' CRCOffC EOL
Seq ' ' EOL
DoOpComments
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC Rapid AbsOrInc Plane CRCOff OfstOff DrillOff 'G98' WFO1 Speed SpinOn EOL
DoPostScript
SeqC AbsOrInc Rapid StrtPos EOL
SeqC CoolOn EOL
SeqC OfstOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqC SpinOff CoolOff EOL
SeqC IncValue OfstOff ' G28 Y0' EOL
SeqC 'M00' EOL
{Start new Operation}
GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC CoolOn EOL
SeqC OfstOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC IncValue OfstOff 'G28 Y0' EOL
{Start new Operation}
GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
SeqC OfstOn EOL
ELSE
{Start new Operation}
GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
FindAnyZMoves {for normal abs subroutine}
IF NoZMoves?
ZonlyRep
ELSE
G92Sub {pattern shift, not element}
END
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqC FeedC CRCOffC ZCP3C FeedRateC EOL
ELSE
SeqC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# ZDepth# {.81}
ToolPath
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqC 'G80' EOL
IF Repeats?
FinishSubG92
END
SeqC RapidC ZCP3C EOL
END
END
NextOp {loops back to EachOP until last Operation}
{End of program ************************************************************}
{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqC SpinOff CoolOff EOL
SeqC IncValue OfstOff ' G28 Y0' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqC AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
SeqC 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
Wyszukiwarka
Podobne podstrony:
Fanuc 6M (AGA1) M148 81 2Fanuc 6M [AP] M790 89Fanuc 6M Mat MC1000V M474 81 1Fanuc 6M LM [AP] NCT45 16 1Fanuc 6M LM [AP] BT45 16 1Fanuc 6M LM [AP] CT45 16 1Fanuc 6M LM [AP] NMT45 16 2Fanuc 6M Trimac (CE) M357 81 1Fanuc 6M MS [FN] M539 81 2Fanuc 6M MS (MM) M185 81 2Fanuc 6M MS [FN] M539 81 2mFanuc 6M Kit (REM) M294 81Fanuc 6M LM [AP] NBT45 16 1Fanuc 6M Shiz [DDM] M272 81Fanuc 10M (AGA) M147 81 2Fanuc 6M [SM] PM956 17 3Fanuc 6M [MC] M710 87więcej podobnych podstron