John Hermans ©1998 John Hermans
Above: John and Robyn with kids Ben and Jill over the tail race and main shaft.
number of potential sites that are suitable for 240 vac
or seven years, my family and I
which have low to medium head (1 to 6 meters) and
have been deriving 100% of our
flow rates which are considerably higher. This situation
usually requires a river frontage property as opposed to
electrical energy needs from a 240
a creek. It is the Nicholson River of East Gippsland,
vac alternator driven by a low head,
Victoria, Australia which provides us with just that: a low
axial flow turbine. During this time and head (1.2 meters) but high volume (100 to 2000 liters
per second).
the years leading to its development
The Weir
and installation, I read many articles on
Perhaps the only real obstacle to the construction of a
micro hydro electrical systems.
similar system is the ability to build a water
impermeable concrete and rock wall. This wall is
It is apparent that in recent years the number of micro-
required to allow water to enter the penstock (the piping
hydro installations have increased. This is due to their
to the turbine). It should not only resist flood damage,
higher efficiency of operation and the availability of
but should not initiate erosion problems in times of
smaller, less costly units. These are primarily designed
flood. Its potential to be undermined by water under
for constant battery charging. I am always intrigued to
pressure must be avoided. Such a site should
read of an installation that has a pure 240 vac output,
preferably have a monolithic rock base for the majority
but it is quite rare to find such an article, thus I am
of its length. The use of low level walls across rivers
prompted to write this one.
gives rise to minimal ecological impact. It is evident
Site Selection from my own installation with a small fish ladder that
Of the hundreds of existing micro-hydro installations aquatic life is still free to move up and down the stream.
along the east coast of Australia, very few would readily This is most certainly not the case only 1 kilometer
adapt to a 240 vac output due to the small volume of upstream, where there is a 10 meter high concrete weir
water on which they operate. But, there are a large built to supply water to the nearby coastal towns.
36 Home Power #65 " June / July 1998
Low head installations are often
subject to annual submergence by
local flooding. In my case, this has
minimal impact on the mechanical
components. My only preparation
for such a submergence is to
remove and carry the alternator to
high ground. This is a small price to
pay for the high returns we receive
from this system.
Providing an installation with high
flood resistance can be achieved if
some basic principles are used. To
increase flood resistance:
" Use high strength concrete with
Above: An upstream view of the hydro installation and the 1.2 meter high
water-proofing admixes at rock
weir. The  power tower in the foreground houses the alternator and pump.
interfaces and include multiple
drilled-in-place 12 mm rebar
people from going ahead with their installations. On one
anchors.
occasion, I had four meters of flood water over the top
" Use large diameter stainless steel anchor bolts with
of the alternator  power tower for two days. Yet, my
epoxy resins.
only chore after the waters subsided was to pump fresh
grease into the bearings in order to displace water. After
" Use heavy steel construction.
20,000 hours, the running gear has been submerged at
" Use pipe bracing.
least six times and the bearings have been changed
only once.
" Use metal plate water and debris reflectors.
Pumping Water
" Galvanize and epoxy paint steel that is frequently
An additional benefit of my turbine is its use in driving a
submerged.
Grundfos multi-stage centrifugal pump. This pump
" Position mechanical components out of line of flowing
delivers 1 liter per second to a 220 thousand liter
debris.
concrete tank situated 100 meters vertically above the
river. This is achieved by taking the v-belts off the
It is very possible for an entire system to be swept
alternator and flywheel and placing them on the pump.
away. This threat has undoubtedly prevented many
Flywheel Use
Below: Turbine (not running) outlet showing PTO shaft
The constant output of the 4 kVa alternator is relatively
with CV joints from an old Subaru.
small (1.2 kVa) but is adequate for all our household
and workshop requirements. (The exception is my
welder, which is diesel powered. Putting out 250 Amps
at 40 Volts does not come easily in many alternative
energy systems). The use of a 30 kilogram, 400 mm
diameter steel flywheel, spinning at 50 revolutions per
second, is invaluable for starting induction motors up to
1.5 hp. Its stored energy is transferred smoothly to the
alternator when sudden heavy loads are applied. This
leads to minimal voltage and frequency drop,
eliminating lighting flicker.
Design for Low Flow
The axial flow water turbine does not lend itself to
throttling via reduction of the water flow through the
turbine pipe. 200 liters per second is required to run the
turbine. In summer, and other times of flows less than
200 liters per second, a turbine shutoff valve is
Home Power #65 " June / July 1998 37
Systems
Above: The Power Tower houses the alternator Above: The other side of the Power Tower showing
(upper left), the 30 kg flywheel (lower left), the drive shaft, primary step-up belting,
and the pump (lower right). and the pump (in pumping mode).
Hermans Hydro System
80mm PVC water pipe (100 vertical meters to supply tank)
Pelton Wheel & Alternator
Multiple Pairs of Microswitch Control Wires (to house)
(1.2 KVA at 240 VAC
from 2 L/s at 100 meter head)
Valve
240 VAC (400 meters to house)
Pelton Wheel & Automotive Alternator
Overspeed
Alternator Relay
(10 Amps at 12 Volt DC from
Sensor
Change-
1/2 L/s at 100 meter head)
Valve
over Underspeed
Relay Sensor
1600 Watt
Immersion
12 Volt Battery
Resistor
(powers system
controls)
Disconnect
Relay
Hydraulic
Grunfoss 12 Stage
Control Valve
Centrifugal Pump
(1 L/s to 100 Meters)
1.2 Meter Weir
Float Macron Alternator
2 x  A Section
(with fish ladder)
Switch (1.2 KVA at 240 VAC from
 V Belting
200 L/s at 1.2 meter Head)
Recycled Automotive C.V. Joints
(with new waterproof boots)
Trash, Fish, &
Brass Ram
Platypus Grate
30 Kg Steel Flywheel
1/4 Turn
Butterfly Valve
 Components not to scale.
Low Head (1.2 meters) Axial Flow Turbine
 Ground wires omitted.
38 Home Power #65 " June / July 1998
Systems
All Purpose Water Supply
Hermans Hydro, cont.
220,000 Liter Concrete Tank
100 meters above river pump
Key:
and pelton wheel hydros
Water Pipe
240 vac Hot
240 vac Common
12 VDC Positive
12 VDC Negative House is active / passive solar and earth sheltered.
15 meters below water tank.
Control / Signal
Water To House
Controls Wires
To House
240 VAC
R.C.D.
Distribution Center
Spike
Hydro / Inverter
Fused Disconnect
Arrestor
Changeover Relay
To 240 VAC
House Loads
600 Watt
Selectronic Inverter
Recycled Telecom Batteries
Battery Charger
(six 2 Volt cells, at 500 Amp-hours each, wired in series)
(homemade )
25 W 50 W 100 W 200 W 400 W 800 W
Current Frequency
Transformer Control Board
To Hydro
(digital micro-
400 Meters
processor)
Voltage
Six SSRs
Transformer
essential. A falling weir water level is a common duty cycle of 80%, running 20 minutes on and 5
problem in many installations and is overcome in my minutes off.
system in two ways. First, I use a bilge pump float
A preferred method of dealing with variable flow rates is
switch in the weir water supply. This opens the control
to use a cross-flow turbine which can be throttled by
switch for the turbine valve when the water level falls
either a pivoting guidevane or a shutter arrangement
approximately 70 mm. The control switch closes the
across the water jet. This throttling ability, and the ease
turbine valve in the penstock, shutting the system
of home manufacture, makes this turbine a first choice
down. When the water level is restored the switch
for many low head installations.
closes to start the alternator spinning again. If the
turbine takes 200 l/s to run constantly, but only 160 l/s To counter low flows, we also use a small battery bank
was available, then the alternator-turbine would have a and inverter. Our TV, stereo, and computer are all
Left: A home-made mercury bulb
float switch controls the butterfly
valve that adjusts flow through the
turbine.
Right: A hydraulic ram, driven by
water pressure from the tank 100
meters higher, actuates the butterfly
valve.
Home Power #65 " June / July 1998 39
Systems
Technology for Communities and the
Environment (APACE) located at the
University of Technology Sydney
(UTS). Its development began when
APACE, an Australian government
aid program, began installing 240
vac micro-hydro systems in the
Pacific Islands. UTS has been using
this control board as an educational
tool for senior and post graduate
students for over ten years. It has
undergone thousands of hours of
testing.
The circuit board itself is only 150
mm square. It uses a digital
microprocessor incorporating a
special algorithm to maintain
alternator frequency to within one
cycle per second on either side of 50
Hz. The software resides in ROM
Above: Control and meter box with lightbulbs used for diversion loads.
and the unit is programmed to
permanently wired to a 600 watt inverter. All other loads
handle the high speed response required for low kW
are automatically switched over to the inverter when the
output micro-hydro systems. For over three years, this
alternator switches off by either the float switch or
unit has proved faultless in my system.
manual controls. A slight flicker of the lights at night is
The control method maintains full load on the alternator
all that is evident. In times of low river flow, most of my
by matching the power output to the load. This is
1.2 kVa goes into battery charging.
accomplished by monitoring the frequency for variation
Frequency Control
and switching dummy loads.
The heart of this micro-hydro installation is the
In my case, the dummy loads are six incandescent light
electronic  stand alone computer frequency control
bulb sets: 25, 50, 100, 200, 400, and 800 watts. The
board. For four years, I had a very crude electronic load
digital microprocessor determines which combination of
control which shunted unused power into either 400 or
the six loads to have on in order to maintain 50 Hz, and
800 watt dummy loads. This system was less than
hence 240 volts. There are 64 combinations available,
adequate on many occasions. My quest to find a more
from 25 to 1600 watts in 25 watt increments. Thus, if
appropriate controller was not an easy one. After much
the house is using little of the generated power, say
searching, I chanced upon an electronic control board
only 250 watts of night lighting, the controller will make
which not only works well, but leads the technology
world-wide. I now have the first installation in Australia.
An Australian electronics engineer designed the
frequency control board in conjunction with Appropriate
Left: The
frequency
control board,
made by the
University of Right: John
Technology, changes belts
Sydney, keeps to switch the
the ac hydro from
waveform alternator to
within spec. pump.
40 Home Power #65 " June / July 1998
Systems
qty item cost
%
NO-HASSLE WATER POWER
1 Concrete water tank $4,000 28%
If you have a reasonably fast running stream
1 240 V pelton wheel/alternator $3,000 21%
or tide nearby and 12 of water
12 or 24
450 meters of 80mm PVC Pipe $1,500 10% clear, Aquair UW Submersible
VDC
Generator can produce 60 to 100
2 Macron 4 KVA alternators $1,300 9%
Watts continuously, up to 2.4 KWH
400 meters of paired cable $1,200 8%
per day. NO TURBINES, NO DAMS,
1 Grundfoss centrifugal pump $1,000 7%
NO PIPES! Water speed
5 mph (brisk walk) = 60W.
1 Frequency controller $1,000 7%
8 mph (slow jog) = 100W.
1 Tower of Power $600 4%
Timber, rock, or natural
1 Concrete weir $500 3%
venturi increases output.
1 12 V pelton wheel/alternator $200 1%
Jack Rabbit Energy Systems
425 Fairfield Ave., Stamford, CT 06902
total $14,300
(203) 961-8133 " FAX (203) 358-9250
up the difference. It will turn on the 50, 100, and 800
e-mail: JackRabbitMarine@compuserve.com
watt dummy loads to produce the total 1200 watt load
requirement. The load adjustments occur at the rate of
ten per second, in 25 watt steps, which at times gives
the appearance of a disco going on at the rear of my
Excellent for controlling
garage. The light bulbs still manage a few years of use. variac
and testing various
electronic products such
Damage Control
as, motors, transformers, lighting controls,
Included with my control system is a separate circuit
school electronics labs, designing high
board which is mounted close to the alternator. In case voltage battery chargers. 1000VA $111.89
of control board or power line failure, it senses
potentially damaging under and over frequency. It then
multimeter
Basic Digital
responds by shutting down the turbine-alternator unit.
Multimeter with transistor  hfe and continuity
test. $15.99
Access
Author: John Hermans, 320 Bellbird Rd., Clifton Creek,
We also carry
Vic. 3875, Australia 1-888-456-4517
FORKLIFTS
Micro-hydro governor available from J. A. Brebner PL,
Associated Elec. & Eng. Co.
74 Second St., Ashbury, N. S. W. 2193, Australia
PO Box 4766, Santa Clara, CA 95056
E-Mail: pfa@ozemail.com.au
Web: www.pactok.net.au/docs/apace/home.htm
FREE PV PANEL/MICROSINE
INVERTER SYSTEM
If you would like to be among the first in the U.S. to connect a
photovoltaic system to your utility, and assist in our testing
program, you may be eligible for a
 FREE PV PANEL/MICROSINE INVERTER SYSTEM .
Trace Engineering is interested in testing new products in at
least ten locations nationwide. Just send your name
(or organization name) address, phone/fax or e-mail address
Microsine AC Module.
to: Trace Engineering, FIRST ON-LINE PROJECT, Marketing
Dept., 5916 195th Northeast, Arlington WA 98223 (or,
®
inverters@traceengineering.com).
Ten systems will be assigned to selected owners very soon.
Home Power #65 " June / July 1998 41


Wyszukiwarka

Podobne podstrony:
Pomysł na naturę ogrody barokowe w Polsce
33 pomysły na odzyskanie natchnienia
Monety pomorskie – pomysł na ciekawą i niepowtarzalną kolekcję
Zwariowane pomysły na randkę
101 pomyslow na wlasna firme
Wprowadzanie wzorow na v,r,en elektronow

więcej podobnych podstron