A P P E N D I X
A
GLOSSARY OF
FIBER OPTIC TERMS
Absorption: That portion of fiber optic attenuation that is the result of conver-
sion of optical power to heat.
Analog: Signals that are continually changing, as opposed to being digitally
encoded.
Attenuation: The reduction in optical power as it passes along a fiber, usually
expressed in decibels (dB). See Optical loss.
Attenuation coefficient: Characteristic of the attenuation of an optical fiber per
unit length, in dB/km.
Attenuator: A device that reduces signal power in a fiber optic link by inducing
loss.
Average power: The average over time of a modulated signal.
Back reflection, optical return loss: Light reflected from the cleaved or polished
end of a fiber caused by the difference of refractive indices of air and glass.
Expressed in dB relative to incident power.
Backscattering: The scattering of light in a fiber back toward the source, used to
make OTDR measurements.
Bandwidth: The range of signal frequencies or bit rate within which a fiber optic
component, link, or network will operate.
Bending loss, microbending loss: Loss in fiber caused by stress on the fiber bent
around a restrictive radius.
219
220 APPENDIX A GLOSSARY OF FIBER OPTIC TERMS
Bit: An electrical or optical pulse that carries information.
Bit-error rate (BER): The fraction of data bits transmitted that are received in
error.
Buffer: A protective coating applied directly on the fiber.
Cable: One or more fibers enclosed in protective coverings and strength mem-
bers.
Cable plant, fiber optic: The combination of fiber optic cable sections, connec-
tors, and splices forming the optical path between two terminal devices.
CATV: An abbreviation for community antenna television or cable TV.
Chromatic dispersion: The temporal spreading of a pulse in an optical wave-
guide caused by the wavelength dependence of the velocities of light.
Cladding: The lower refractive index optical coating over the core of the fiber
that traps light into the core.
Connector: A device that provides for a demountable connection between two
fibers or a fiber and an active device and provides protection for the fiber.
Core: The center of the optical fiber through which light is transmitted.
Coupler: An optical device that splits or combines light from more than one
fiber.
Cutback method: A technique for measuring the loss of bare fiber by measuring
the optical power transmitted through a long length then cutting back to the
source and measuring the initial coupled power.
Cutoff wavelength: The wavelength beyond which singlemode fiber only supports
one mode of propagation.
dB: Optical power referenced to 1 microwatt.
dBm: Optical power referenced to 1 milliwatt.
Decibel (dB): A unit of measurement of optical power that indicates relative
power on a logarithmic scale, sometimes called dBr. dB = 10 log (power ratio)
Detector: A photodiode that converts optical signals to electrical signals.
Digital: Signals encoded into discrete bits.
Dispersion: The temporal spreading of a pulse in an optical waveguide. May be
caused by modal or chromatic effects.
Edge-emitting diode (E-LED): A LED that emits from the edge of the semicon-
ductor chip, producing higher power and narrower spectral width.
End finish: The quality of the end surface of a fiber prepared for splicing or ter-
minated in a connector.
Equilibrium modal distribution (EMD): Steady state modal distribution in multi-
mode fiber, achieved some distance from the source, where the relative
power in the modes becomes stable with increasing distance.
ESCON: IBM"! standard for connecting peripherals to a computer over fiber
optics. Acronym for enterprise system connection.
Excess loss: The amount of light lost in a coupler beyond that inherent in the
splitting to multiple output fibers.
APPENDIX A GLOSSARY OF FIBER OPTIC TERMS 221
Fiber Distributed Data Interface (FDDI): 100 Mb/s ring architecture data net-
work.
Ferrule: A precision tube that holds a fiber for alignment for interconnection or
termination. A ferrule may be part of a connector or mechanical splice.
Fiber identifier: A device that clamps onto a fiber and couples light from the fiber
by bending, to identify the fiber and detect high-speed traffic of an operating
link or a 2 kHz tone injected by a test source.
Fiber optics: Light transmission through flexible transmissive fibers for commu-
nications or lighting.
Fiber tracer: An instrument that couples visible light into the fiber to allow visual
checking of continuity and tracing for correct connections.
FO: Common abbreviation for fiber optic.
Fresnel reflection, back reflection, optical return loss: Light reflected from the
cleaved or polished end of a fiber caused by the difference of refractive
indices of air and glass. Typically 4 percent of the incident light.
Fusion splicer: An instrument that splices fibers by fusing or welding them, typi-
cally by electrical arc.
Graded index (GI): A type of multimode fiber that uses a graded profile of
refractive index in the core material to correct for dispersion.
Index matching fluid: A liquid used of refractive index similar to glass used to
match the materials at the ends of two fibers to reduce loss and back reflection.
Index profile: The refractive index of a fiber as a function of cross section.
Index of refraction: A measure of the speed of light in a material.
Insertion loss: The loss caused by the insertion of a component such as a splice or
connector in an optical fiber.
Jacket: The protective outer coating of the cable.
Jumper cable: A short single-fiber cable with connectors on both ends used for
interconnecting other cables or testing.
Laser diode (ILD): A semiconductor device that emits high-powered, coherent
light when stimulated by an electrical current. Used in transmitters for single-
mode fiber links.
Launch cable: A known good fiber optic jumper cable attached to a source and
calibrated for output power used for loss testing. This cable must be made of
fiber and connectors of a matching type to the cables to be tested.
Light-emitting diode (LED): A semiconductor device that emits light when stim-
ulated by an electrical current. Used in transmitters for multimode fiber links.
Link, fiber optic: A combination of transmitter, receiver, and fiber optic cable
connecting them capable of transmitting data. May be analog or digital.
Long wavelength: A commonly used term for light in the 1300 and 1550 nm
ranges.
Loss budget: The amount of power lost in the link. Often used in terms of the
maximum amount of loss that can be tolerated by a given link.
222 APPENDIX A GLOSSARY OF FIBER OPTIC TERMS
Loss, optical: The amount of optical power lost as light is transmitted through
fiber, splices, couplers, and the like.
Margin: The additional amount of loss that can be tolerated in a link.
Mechanical splice: A semipermanent connection between two fibers made with
an alignment device and index matching fluid or adhesive.
Micron (m): A unit of measure, 10 6 m, used to measure wavelength of light.
Microscope, fiber optic inspection: A microscope used to inspect the end surface
of a connector for flaws or contamination or a fiber for cleave quality.
Modal dispersion: The temporal spreading of a pulse in an optical waveguide
caused by modal effects.
Mode: A single electromagnetic field pattern that travels in fiber.
Mode field diameter: A measure of the core size in singlemode fiber.
Mode filter: A device that removes optical power in higher-order modes in fiber.
Mode scrambler: A device that mixes optical power in fiber to achieve equal
power distribution in all modes.
Mode stripper: A device that removes light in the cladding of an optical fiber.
Multimode fiber: A fiber with core diameter much larger than the wavelength of
light transmitted that allows many modes of light to propagate. Commonly
used with LED sources for lower-speed, short-distance links.
Nanometer (nm): A unit of measure, 10 9 m, used to measure the wavelength of
light.
Network: A system of cables, hardware, and equipment used for communica-
tions.
Numerical aperture (NA): A measure of the light acceptance angle of the fiber.
Optical amplifier: A device that amplifies light without converting it to an elec-
trical signal.
Optical fiber: An optical waveguide, comprised of a light-carrying core and
cladding that traps light in the core.
Optical loss test set (OLTS): A measurement instrument for optical loss that in-
cludes both a meter and source.
Optical power: The amount of radiant energy per unit time, expressed in linear
units of Watts or on a logarithmic scale, in dBm (where 0 dB = 1 mW) or dB
(where 0 dB = 1 W).
Optical return loss, back reflection: Light reflected from the cleaved or polished
end of a fiber caused by the difference of refractive indices of air and glass.
Typically 4 percent of the incident light. Expressed in dB relative to incident
power.
Optical switch: A device that routes an optical signal from one or more input
ports to one or more output ports.
Optical time domain reflectometer (OTDR): An instrument that uses backscat-
tered light to find faults in optical fiber and infer loss.
APPENDIX A GLOSSARY OF FIBER OPTIC TERMS 223
Overfilled launch: A condition for launching light into the fiber where the
incoming light has a spot size and NA larger than accepted by the fiber, fill-
ing all modes in the fiber.
Photodiode: A semiconductor that converts light to an electrical signal, used in
fiber optic receivers.
Pigtail: A short length of fiber attached to a fiber optic component such as a laser
or coupler.
Plastic-clad silica (PCS) fiber: A fiber made with a glass core and plastic cladding.
Plastic optical fiber (POF): An optical fiber made of plastic.
Power budget: The difference (in dB) between the transmitted optical power (in
dBm) and the receiver sensitivity (in dBm).
Power meter, fiber optic: An instrument that measures optical power emanating
from the end of a fiber.
Preform: The large diameter glass rod from which fiber is drawn.
Receive cable: A known good fiber optic jumper cable attached to a power meter
used for loss testing. This cable must be made of fiber and connectors of a
matching type to the cables to be tested.
Receiver: A device containing a photodiode and signal conditioning circuitry
that converts light to an electrical signal in fiber optic links.
Refractive index: A property of optical materials that relates to the velocity of
light in the material.
Repeater, regenerator: A device that receives a fiber optic signal and regenerates
it for retransmission, used in very long fiber optic links.
Scattering: The change of direction of light after striking small particles that
causes loss in optical fibers.
Short wavelength: A commonly used term for light in the 665, 790, and 850 nm
ranges.
Singlemode fiber: A fiber with a small core, only a few times the wavelength of
light transmitted, that allows only one mode of light to propagate. Com-
monly used with laser sources for high-speed, long-distance links.
Source: A laser diode or LED used to inject an optical signal into fiber.
Splice, fusion or mechanical: A device that provides for a connection between
two fibers, typically intended to be permanent.
Splitting ratio: The distribution of power among the output fibers of a coupler.
Steady state modal distribution: Equilibrium modal distribution (EMD) in multi-
mode fiber, achieved some distance from the source, where the relative
power in the modes becomes stable with increasing distance.
Step-index fiber: A multimode fiber where the core is all the same index of
refraction.
Surface emitter LED: A LED that emits light perpendicular to the semiconductor
chip. Most LEDs used in datacommunications are surface emitters.
224 APPENDIX A GLOSSARY OF FIBER OPTIC TERMS
Talkset, fiber optic: A communication device that allows conversation over
unused fibers.
Termination: Preparation of the end of a fiber to allow connection to another
fiber or an active device, sometimes also called connectorization .
Test cable: A short single-fiber jumper cable with connectors on both ends used
for testing. This cable must be made of fiber and connectors of a matching
type to the cables to be tested.
Test kit: A kit of fiber optic instruments, typically including a power meter,
source, and test accessories, used for measuring loss and power.
Test source: A laser diode or LED used to inject an optical signal into fiber for
testing loss of the fiber or other components.
Total internal reflection: Confinement of light into the core of a fiber by the
reflection off the core-cladding boundary.
Transmitter: A device that includes a LED or laser source and signal condition-
ing electronics used to inject a signal into fiber.
Visual fault locator: A device that couples visible light into the fiber to allow
visual tracing and testing of continuity. Some are bright enough to allow
finding breaks in fiber through the cable jacket.
Watts: A linear measure of optical power, usually expressed in milliwatts (mW),
microwatts (�W), or nanowatts (nW).
Wavelength: A measure of the color of light, usually expressed in nanometers
(nm) or microns (�m).
Wavelength division multiplexing (WDM): A technique of sending signals of sev-
eral different wavelengths of light into the fiber simultaneously.
Working margin: The difference (in dB) between the power budget and the loss
budget (i.e., the excess power margin).
Wyszukiwarka
Podobne podstrony:
Glossary Of Greek Grammar Terms6 Glossary of End Time Terms and the MillenniumGlossary of Open Access terms1 The Origins of Fiber Optic Communications20 Appendix B Fiber Optic StandardsStudent s Glossary of literary termsGlossary of Terms LDAirflow Glossary of TermsGlossary of wood and woodworking terms3 Fiber Optic Networks2000 Influence of Fiber Fermentability on Nutrient Digestion in the Dog17 Fiber Optic Testing14 Estimating and Bidding Fiber Optic InstallationXArchitectural Glossary of Residential Construction19 The Basis of ECG Diagnosis2 Basics of Fiber OpticsSHSpec 19 6404C30 Effectiveness of Processingwięcej podobnych podstron