221808B.12.00
Instructions for Use
Installation and Servicing
To be l ef t wi t h t he user
Hideaway 50
G.C. No. 41 313 15
Open Flue Boiler
BS 6332
BS 5258
This is a Cat I2H Appliance
Reference in these instructions to British Standards and Statutory
Regulations/Requirements apply only to the United Kingdom.
For Ireland the rules in force must be used.
The instructions consist of three parts, User, Installation and Servicing Instructions, which includes the Guarantee Registration
Card. The instructions are an integral part of the appliance and must, to comply with the current issue of the Gas Safety
(Installation and Use) Regulations, be handed to the user on completion of the installation.
Guarantee Registration
Thank you for installing a new Glow-worm appliance in your home.
Glow-worm appliances' are manufactured to the very highest standard so we are pleased
to offer our customers' a Comprehensive First Year Guarantee.
In the center pages are to be found your Guarantee Registration Card, which we recommend you complete and
return as soon as possible.
If this card is missing you can obtain a copy or record your registration by telephoning the Heatcall Customer
Service number 01773 828100.
Our Guarantee gives you peace of mind plus valuable protection against breakdown by covering the cost of:
' REGISTER YOUR GLOW-WORM APPLIANCE
All replacement parts
O'
FOR 1ST YEAR GUARANTEE PROTECTION
' All labour charges
O'
' All call-out charges
O'
CALL 0208 247 9857
Hepworth Heating Ltd.,
Customer Services:
Nottingham Road, Belper, Derbyshire. DE56 1JT
Tel: (01773) 828100
General/Sales enquiries:
Tel: (01773) 824141 Fax: (01773) 820569
One Contact Local Service Fax: (01773) 828070
1037
Important Information
2. Directive 73/23/EEC on the harmonization of the Laws of the
Notes and General Information
Member States relating to electrical equipment designed for
Please read these instructions and follow them carefully for the
use within certain voltage limits.
safe and economical use of your boiler.
3. Directive 89/336/EEC on the approximation of the Laws of
The boiler is automatic in operation, once the pilot is lit and the
the Members States relating to electromagnetic
controls have been set.
compatibility.Information for the Installer and Service Engineer.
Glow-worm Hideaways are central heating boilers, to provide
heating and if required an indirect domestic hot water supply.
Control of Substances Hazardous to Health
Under Section 6 of The Health and Safety at Work Act 1974, we
Important Notice
are required to provide information on substances hazardous to
This boiler is for use only on G20 gas. health.
The adhesives and sealants used in this appliance are cured
Gas Safety (Installation and Use) Regulations
and give no known hazard in this state.
In your own interests and that of safety, it is the Law that ALL gas
Insulation Pads/Ceramic Fibre, Glassyarn
appliances are installed by a competent person in accordance
with the current issue of the above regulations.
These can cause irritation to skin, eyes and the respiratory tract.
If you have a history of skin complaint you may be susceptible
CE Mark
to irritation. High dust levels are usual only if the material is
broken.
This boiler meets the requirements of Statutory Instrument, No.
3083 The Boiler Efficiency Regulations, and therefore is deemed Normal handling should not cause discomfort, but follow normal
good hygiene and wash your hands before eating, drinking or
to meet the requirements of Directive 92/42/EEC on the efficiency
going to the lavatory.
requirements for new hot water boilers fired with liquid or
gaseous fuels. If you do suffer irritation to the eyes or severe irritation to the skin
seek medical attention.
Type test for purposes of Regulation 5 certified by:
Notified body 0086.
Boiler Thermostat
Product/production certified:
These contain very small amounts of xylene in the sealed phial
and capillary. If broken, under normal circumstances the fluid
Notified body 0086.
does not cause a problem, but in cases of skin contact, wash
The CE Mark on this appliance shows compliance with: with cold water.
If swallowed drink plenty of water and seek medical attention.
1. Directive 90/396/EEC on the approximation of the Laws of
the Member States relating to appliances burning gaseous
fuels.
CONTENTS DESCRIPTION SECTION PAGE No.
INSTRUCTIONS
Introduction 3
Lighting the Boiler 4
FOR USE
INSTALLATION
General Data 1 5
INSTRUCTIONS
Water Systems 2 7
Flue and Ventilation 3 8
Installation 4 9
Casing Location 5 11
Electrical Wiring 6 11
Commissioning 7 12
SERVICING
Servicing 8 15
Replacement Parts 9 17
INSTRUCTIONS
Fault Finding 10 20
Spare Parts 11 24
221808B 2
Instructions for Use
Warning
FLUE
BLOCKAGE
Make sure that nothing obstructs the rear side grilles or
clearances. See diagram 1.2 and 1.3 for minimum clearances.
SAFETY
DEVICE GAS CONTROL
Boilers Installed in a Compartment
RESET KNOB 'A'
If the boiler is fitted in a compartment, cupboard etc., do not BUTTON
obstruct the purpose built compartment vents or grille on the
boiler.
Do not use the compartment for storage purposes.
PIEZO
IGNITION
Maintenance
BUTTON
To ensure the continued efficient and safe operation of the
'C'
boiler it is recommended that it is checked and serviced at
regular intervals. The frequency of servicing will depend upon
the particular installation conditions and usage, but in general
once a year should be enough.
THERMOSTAT
If this appliance is installed in a rented property there is a duty
CONTROL
of care imposed on the owner of the property by the current
issue of the Gas Safety (Installation and Use) Regulations,
KNOB 'B'
Section 35.
It is the law that servicing is carried out by a competent person.
SETTING
SETTING
To obtain service please call your installer or Heatcall (Glow-
POINTS
POINT
worm s own service organisation) using the telephone number
given on the inside of the front panel.
Please be advised that the Benchmark logbook should be
GAS CONTROL KNOB
completed by the installation engineer on completion of
commissioning and servicing.
= OFF
All CORGI Registered Installers carry a CORGI ID card, and = PILOT/IGNITION
have a registration number. Both should be recorded in your
= MAIN BURNER
boiler Logbook. You can check your installer is CORGI registered
by calling CORGI direct on :- 01256 372300.
Boiler Electrical Supply
WARNING. This boiler must be earthed.
E
The boiler must only be connected to a 240V~50Hz supply,
protected by a 3A fuse, maximum.
All wiring must be in accordance with the current issue of
BS7671.
Heat resistant cable having a conductor size of 0.75mm2, (24/
0.22mm), to BS6500 Table 16 must be used.
To Connect an Electrical Plug
50 OPEN FLUE
Diagram 1
The colours of three core flexible cable are, Brown - live, Blue
- neutral, Green and yellow - earth.
Safety Device
As the markings on your plug may not correspond with these
This appliance is fitted with a flue blockage safety device which
colours continue as follows:
will shut down the appliance in the event of abnormal flue
The wire coloured brown must be connected to the terminal conditions. This device is NOT a substitute for an independently
marked L or Red. mounted Carbon Monoxide detector.
The wire coloured blue must be connected to the terminal The safety device is reset, after three minutes, by pushing in the
marked N or Black. button shown in diagram 1.
The wire coloured green and yellow must be connected to the Shut down can occur during certain climate conditions, but if it
terminal marked E , Green or the earth symbol . recurs the chimney flue and air inlet into the room must be
checked and any problems found corrected by a competent
person, before the boiler is used again.
3 221808B
0938
Instructions for Use
To Light the Boiler
To Turn the Boiler Off
WARNING. If the pilot light goes out for any reason, do not
For short periods. Turn the boiler thermostat control knob B
attempt to relight until three minutes have gone by.
anticlockwise to O . The pilot will remain alight. To relight the
main burner turn the thermostat control knob B clockwise to
Remove the door by pulling forwards with the fascia at the top.
the desired setting between MIN and MAX .
Lift up to free from bottom side lugs.
For longer periods. Push in slightly and turn gas control knob
Refer to diagram 1 to identify the controls.
A fully clockwise until is against its setting point. Turn
Check that the mains electrical supply to the boiler is switched
thermostat control knob B anticlockwise to O . Isolate the
OFF.
boiler from the electrical supply. Follow the full lighting procedure
to relight.
Check that the Flue Blockage Safety Device has not operated,
that is, the button is in. Refer to Safety Device instructions.
Refer also to Protection Against Freezing .
Push in slightly and turn gas control knob A clockwise until
' 'is against its setting point.
Gas Leak or Fault
Turn thermostat control knob B anticlockwise until O is
If a gas leak or fault exists or is suspected the boiler must be
against its setting point.
turned off, including the electrical supply and must not be used
until the fault has been put right. Advice/help should be obtained
Push in slightly and turn gas control knob A anticlockwise until
from the local gas undertaking or your installation/servicing
' ' is against its setting point, then push fully and hold in.
company.
Push and release piezo ignition button C until the pilot burner
lights.
Protection Against Freezing
Air may be present in the supply pipe so the lighting of the pilot
If the boiler is to be out of use for any long period of time during
may need to be repeated until all the air has been expelled.
severe weather conditions we recommend that the whole of the
When the pilot is alight, view through window E , keep gas
system including the boiler, be drained off to avoid the risk of
control knob A fully pushed in for about 15 seconds, then
freezing up. If an immersion heater is fitted in the domestic hot
release.
water cylinder make sure it is switched off.
If the burner fails to stay alight, wait three minutes, then repeat
the lighting procedure only now keep control knob A depressed
Sheet Metal Parts
for a little longer before releasing. The Flue Blockage Safety
WARNING. This appliance contains metal parts (component)
Device may also need resetting, refer to instructions above.
and care should be taken when handling and cleaning, with
If the gas control knob A is turned to ' ', a safety lock
particular regard to edges.
prevents it being turned on again for a short period. No attempt
should be made to relight the pilot for at least three minutes.
Cleaning
Make sure that the pilot is alight and stable, then switch on the
Keep the casing clean by wiping it over occasionally with a
electrical supply.
damp soapy cloth and dry with a polishing cloth.
Press in and turn gas control knob A anticlockwise until ' '
Do not use abrasive cleaners.
is against its setting point.
Set any remote controls to call for heat.
Replacement Parts/Boiler Identification
Turn the boiler thermostat knob B clockwise until MAX is
against its setting point and the main burner will light. Adjust If replacement parts are required apply to your local supplier or
thermostat to required setting between MIN and MAX . gas undertaking. Please quote the name of the boiler and its
MAX is about 82oC (180oF). serial number which can be found on the data label positioned
on the boiler top, to the rear of the inclined flueway cleaning
Refit the door by fitting the hooked runner at the bottom into the
door.
slot in the side panels and pushing onto the studs.
Clearance
Minimum clearances must be left around the boiler as shown in
diagram 1.2 and 1.3.
221808B 4
1 General
C
L
FLUE ' A SPECIAL TOP CASING
TO SUIT 600mm (235/8 in.)
F (MIN)
A
WORKTOPS IS AVAILABLE
L (MIN)
N
*
GAS CONNECTION
G
Rc 1/2 (1/2 in. B.S.P.T.)
(MIN)
C
L
WATER CONNECTIONS
FLUE
H
Rc1 (1in. B.S.P.T.)
WATER CONNECTIONS Rc1
K
reduced with DISTRIBUTOR
M
D
(MIN)
B
TUBE to Rc 3/4 (3/4 in. B.S.P.T.)
(pumped return)
C
J (MIN)
=' INSIDE DIAMETER OF
E SOCKET FOR 100mm (4in.)
NOMINAL DIAMETER FLUE
TO BS567
Diagram 1.1
GENERAL DIMENSIONS - given in millimetres (Approx. inches)
A B C D E F G H J K L M N
mm 300 118 598 294 265 533 3 300 445 121 88 900 115
1
in. 113/4 45/8 231/2 111/2 101/2 21 /8 113/4 171/2 43/4 31/2 351/2 41/2
Sheet Metal Parts
Warning. When installing or servicing this boiler care should be HIDEAWAY 50
taken when handling sheet metal parts, to avoid the possibility
of personal injury.
min medium max
RANGE RATING
NOMINAL kW 15.06 16.80 18.64
Important Notice
HEAT INPUT
This boiler is for use only on G20 gas. 51,400 57,300 63,600
(GROSS) Btu/h
Wherever possible, all materials, appliances and components
to be used shall comply with the requirements of British NOMINAL kW
11.72 13.19 14.65
Standards. HEAT
OUTPUT Btu/h 40,000 45,000 50,000
Where no British Standards exist, materials and equipment
should be fit for their purpose and of suitable quality and
BURNER mbar
workmanship.
9.3 11.6 13.9
SETTING
PRESSURE in.w.g 3.7 4.6 5.6
1.1 Data
(HOT)
Approx.weight of boiler: 76kg (168 lb)
205752
INJECTOR
Water content: 5.76litre (1.27 gal)
1.3 Statutory Requirements
Gas connection: Rc1/2(1/2 BSP)
The installation of this boiler must be carried out by a competent
Water connection: Rc1 (1inch BSP)
person in accordance with the relevant requirements of the
current issue of:
Electrical supply: 240V - 50Hz fused at 3A
Manufacturer s instructions, supplied.
Burner: Aeromatic
The Gas Safety (Installation and Use) Regulations, The Building
The Seasonal Efficiency Domestic Boilers UK (SEDBUK) is
Regulations, Local Water Company Byelaws, The Building
71.0%.
Standards (Scotland) Regulations, applicable in Scotland, The
Health and Safety at Work Act, The Control of Substances
The value is used in the UK Government s Standard Assessment
Hazardous to Health, The Electricity at Work Regulations and
Procedure (SAP) for energy rating of dwellings. The test data
any applicable local regulations.
from which it has been calculated have been certified by B.S.I.
Detailed recommendations are contained in the current issue of
the following British Standards and Codes of Practice:
1.2 Range Rating
BS6798, BS5440 Part 1 and 2, BS5449, BS6700, BS6891,
This boiler is range rated and may be adjusted to suit individual
BS5546, BS7478, BS7593, BS7671.
systems. The table gives settings and outputs.
Manufacturer s instructions must not be taken as overriding
The boiler input is supplied preset to maximum and should be
statutory requirements.
adjusted to suit system requirements.
5 221808B
0993
1 General
A compartment used to enclose the boiler must be designed
1.4 B.S.I. Certification
and constructed specifically for this purpose. An existing
This boiler is certificated by B.S.I. for safety and performance.
cupboard or compartment modified for the purpose may be
It is, therefore, important that no alteration is made to the boiler
used. Details of essential features of cupboard and compartment
unless approved, in writing, by Hepworth Heating Ltd.
design are given in the current issue of BS6798.
Any alteration not approved by Hepworth Heating Ltd., could
Make sure that nothing will obstruct the side clearances or side
invalidate the B.S.I. certification, boiler warranty and could also
grilles. If installing the boiler in a compartment make sure that
infringe the statutory requirements.
openings and vents are not obstructed.
1.5 Gas Supply
1.8 Heating System Controls
The gas installation shall be in accordance with the current
The heating system should have installed: a programmer and
issue of BS6891.
room thermostat controlling the boiler.
The supply from the governed meter must be of adequate size
Thermostatic radiator valves may be installed in addition to the
to provide a steady inlet working pressure of 20mbar (8in wg) at
room thermostat.
the boiler.
Note: For further information, see The Building Regulations
On completion test the gas installation using the pressure drop
1991 - Conservation of fuel and power, 1995 edition - Appendix
method and suitable leak detection fluid, purge in accordance
G, table 4b.
with the current issue of BS6891.
1.6 Electrical
Warning. This boiler must be earthed.
The electrical installation must be carried out by a competent
person. All external components must be of the approved type
and must be connected in accordance with the current issue of
BS7671 and any local regulations which may apply.
Connection of the boiler and any system controls to the mains
supply should be through a 3A fused double pole isolating
switch, having a minimum double pole contact separation of
WORKTOP WORKTOP
3mm, serving only the boiler and system controls.
254
Heat resistant flexible cable of at least 0.75mm2, to the current
6
6
issue of BS6500 Table 16 must be used for all connections (10 in.)
(1/4 in.)
(1/4 in.)
within the boiler casing.
1.7 Boiler Location
The boiler must not be installed in a room used or intended to
be used as sleeping accommodation or a room containing a
20 (3/4 in.) 20 (3/4 in.)
bath or shower.
This boiler is not suitable for installation out of doors.
CUPBOARD BOILER CUPBOARD
The boiler must stand on a level floor, conforming with local
authority requirements and building regulations. The base
temperature is within the requirements of the current issue of
Diagram 1.2
TOP & SIDE CLEARANCES
BS5258. The boiler may be stood on a wooden floor but a metal
plate is required to protect plastic tiles and similar floor coverings.
Suitable clearance needs to be available at the sides of the
boiler to ease connection of pipework. The actual clearances
will vary according to site conditions.
When the boiler is to be installed level with work surfaces, WALL OR
minimum clearances to fixtures, walls and the like should be
FIXTURE
provided, see diagram 1.2.
To ease minimum clearances it may be necessary to modify
units or fixtures.
A front access clearance should be provided as shown in
BOILER
diagram 1.3.
530 (21in.)
The minimum gap behind the top casing is dimension G in
diagram1.1. The boiler can be sited further away from the wall
if required to align with kitchen units.
Combustible wall material must be 25mm (1in) away from flue
components.
A special top casing, part number 424858 can be bought, to
enable boiler casings to be arranged flush with 600mm (235/8in)
deep worktops.
Where the installation of the boiler will be in an unusual location,
special procedures may be necessary, the current issue of
Diagram 1.3
FRONT CLEARANCE
BS6798 gives detailed guidance on this aspect.
221808B 6
1020
0911
2 Water Systems
REFER TO BS 5546
2.1 Water Pressure Head
This boiler must not be connected to a sealed water system.
22mm VENT
15mm COLD FEED
This boiler shall only be connected to an open vented cistern
water supply, with a minimum head of 1metre (39in) and a
maximum of 27metre (90ft). INDIRECT
CYLINDER
(Shown with
2.2 Inhibitor
27metres recommended
Max. thermostat and valve).
Attention is drawn to the current issue of BS5449 and BS7593
on the use of inhibitors in central heating systems.
28mm
If an inhibitor is to be used in the system contact should be made
PUMP
with a manufacturer so that they can recommend their most
suitable product.
BOILER
C
If using in an existing system take special care to drain the entire
L
To Heating
system, including the radiators, then thoroughly cleaning out
Circuit
before fitting the boiler, whether or not adding an inhibitor.
DRAIN OFF
Distributor tube in
COCK
pumped return
2.3 Gravity Domestic Hot Water and Pumped
connection
PUMPED HEATING AND GRAVITY
Central Heating
DOMESTIC (DIAGRAMMATIC) Diagram 2.1
It is recommended that a cylinder thermostat is used to prevent
the stored water temperature becoming too high when the
heating pump is off.
The domestic hot water primary flow and return must be 28mm
22mm VENT
od. The installation must comply with the current issue of
BS5546 and BS6700, see diagram 2.1.
15mm
If the above conditions cannot be met, it is suggested that a fully
COLD FEED
pumped system is used.
1 metre
TO INDIRECT
2.4 Pumped Central Heating and Domestic Hot MIN.
CYLINDER
27metres
Water
MAX.
Where a single flow and return is taken from the boiler, a
minimum static head of 1metre (39in) must be provided between
PUMP
the water level in the cold water cistern and the centre of the
waterway, see diagram 2.2. BOILER
C
L
To Heating
2.5 Circulation Pump
Circuit
DRAIN OFF
Distributor tube in
Normally the pump should be set to give a temperature difference
COCK
pumped return
of 11oC (20oF), across the boiler. At the appropriate flow rate the
connection
resistance through the boiler can be found by reference to the
pressure loss graph, diagram 2.3. FULLY PUMPED SYSTEM
(DIAGRAMMATIC)
Diagram 2.2
Use a pump with integral valves or fit valves as close to the
pump as possible.
2.6 Domestic Hot Water Cylinder
FLOW RATE (GALLON/MINUTE)
For all systems supplying domestic hot water the cylinder must
0 1 2 3 4 5 6
be indirect.
800
32
700 28
2.7 Safety Valve
600 24
A safety valve need not be fitted to an open vented system.
500 20
2.8 Draining Tap
400 16
A drain tap must be fitted at the lowest points of the system
which will allow the draining of the entire system, including the 300
12
boiler and domestic hot water cylinder.
200 8
100 4
0
0
0 4 8 12 16 20 24 28
FLOW RATE (LITRES/MINUTE)
PRESSURE LOSS OF BOILER Diagram 2.3
7 221808B
0869
0870
0872
WATER PRESSURE LOSS
(INCHES HEAD OF WATER)
WATER PRESSURE LOSS
(mm HEAD OF WATER)
3 Flue and Ventilation
Important Note 3.5 Ventilation for Boilers Installed in a
Cupboard or Compartment
The boiler is fitted with a Flue Blockage Safety Device, which
will shut down the boiler if there is an unacceptable spillage of
When the boiler is fitted in a cupboard or compartment, high and
products at the draught diverter.
low level purpose designed, permanent openings must be
provided to supply air for combustion and compartment
This safety device MUST NOT under any circumstances be
ventilation.
interferred with or put out of action. The safety device must only
be replaced with the Glow-worm parts.
The air vents must have minimum areas in accordance with
Compartment Air Vent B . The figures quoted refer to the
3.1 Flue minimum acceptable effective area.
Both the high and low level openings must communicate with
The integral draught diverter on the Hideaway range of boilers
the same room, or must both be on the same wall to outside air.
makes the combustion performance independent of conditions
in the secondary flue, but in common with other fuels an efficient
If air vent grilles are fitted to a cavity wall, the opening through
flue is necessary to make sure of a trouble free installation.
the wall must be ducted.
The flue must be at least equivalent to 1m vertical.
Where ventilation air to a compartment is taken from a room or
space, then the room or space must be fitted with a ventilation
The boiler flue socket is designed to take flue pipes to the
opening as specified in Air Vent Table A .
current issue of BS567. If a flue pipe to BS715 is to be used, an
adapter must be fitted to the boiler flue socket, as diagram 1.1.
For information regarding compartment requirements refer to
the appropriate section of the current issue of BS6798.
The flue must be in accordance with the current issue of
BS5440 Part 1.
AIR VENT TABLE 'A' FOR
3.2 Flue Guidelines
ROOM/SPACE INSTALLATIONS
The flue should be kept as short as possible. Horizontal or very
shallow runs of the flue should be avoided as they encourage
EFFECTIVE cm2
55
local cooling.
AREA OF VENT
in2 8
Always choose a flue route which will cause the least cooling of
the flue.
COMPARTMENT AIR VENT TABLE 'B'
There should be a vertical rise of at least 600mm (2ft) before
using a bend. 90o elbows should not be used.
COMPARTMENT
End with a certificated flue terminal, preferably above ridge
VENTILATION
HIGH LEVEL LOW LEVEL
height, but at least above the eaves of a pitched roof.
REQUIREMENTS
VENT AREA VENT AREA
An existing chimney must be thoroughly swept and all debris
cleared away before lining.
VENTILATION
172cm2 26in2 344cm2 52in2
3.3 Timber Frame Buildings
FROM ROOM
If the boiler is to be installed in a timber frame building it should OR SPACE
be fitted in accordance with the Institute of Gas Engineers
86cm2 13in2 172cm2 26in2
FROM
document IGE/UP/7/1998. If in doubt seek advice from the local
gas undertaking or Hepworth Heating Ltd. OUTSIDE
3.4 Ventilation for Boiler Installed in a Room
or Space
If the boiler is to be installed in a room or space a purpose
3.6 Extract Fans
designed permanent ventilation opening, to supply air for
combustion, must be provided on an outside wall to external air,
If an extract fan is fitted in the premises, there is a possibility that
refer to the current issue of BS5440 Part 2 for details.
if adequate inlet openings are not provided, spillage of the
products from the boiler could occur.
The opening may be directly into the room or the space
containing the boiler, or an outside wall of an adjacent room or
When openings are fitted in accordance with the current issue
space which has an internal permanent air vent, of the same
of BS5440 Part 2 and this section, extract fans should not cause
size, into the room or space containing the boiler.
down draught, but where such fan installations are found, a
spillage test must be carried out in accordance with the current
Do not ventilate through a bedroom, bedsitting room, private
issue of BS5440 Part 1 and any corrective work done.
garage or a room containing a bath or shower.
When the boiler is installed in a room or internal space already
containing other fuel burning appliances then the air supply of
such appliances must be taken into account.
The ventilation opening areas are given in Air Vent Table A .
The figures quoted refer to the minimum acceptable effective
area.
221808B 8
4 Installation
Before fitting the boiler make sure the location selected is in
CAPTIVE
CASING
accordance with the requirements of Section 1.7.
NUT
BRACKET
4.1 Unpacking
The boiler casing panels are packed separately within the main
case. They are designed to enable the gas and water connections
to be made before fitting the casing panels.
The main casing brackets, distributor tube and loose items, in a
plastic bag, are packed in the top fitment.
4.2 Casing Brackets
No.8 SCREW (8)
Fit the four casing brackets as shown in diagram 4.1, using eight
No.8 screws.
Push the captive nuts, supplied loose, on to the casing brackets
as shown in diagram 4.1.
CAPTIVE
4.3 Water Connections - Gravity Domestic Hot
CASING
NUT
Water and Pumped Heating BRACKET
Diagram 4.1
Fit suitable fittings into the boiler tappings, see diagram 4.2. CASING BRACKETS FITTING
Connect pipework into prepared fittings, making sure that all
pipes are taken backwards and will clear the casings, see
diagram 1.1.
ALTERNATIVE
Heating flow, any one connection of the upper connections may HEATING OR
be used.
DOMESTIC
HOT WATER
Gravity domestic hot water flow, any one connection of the
remaining upper connections may be used.
FLOW
Heating return, the distributor tube MUST be fitted into either
one of the front lower connections on ALL installations, see
ALTERNATIVE
diagram 4.3. The distributor tube is packed in the top carton
HEATING
fitment.
RETURN
Gravity domestic hot water return, any one connection of the
With distributor
three remaining lower connections may be used.
tube (not shown)
GRAVITY
When the front connections are used it is essential that any
DOMESTIC
pipework or fittings do not stick out more than the amount shown
RETURN TO
in diagram 4.4.
ANY OF THE
If limited space only is available, it is recommended that the front
3 REMAINING
connections are used.
LOWER CONNECTIONS
Fit plugs into unused tappings.
WATER CONNECTIONS - GRAVITY
Do not route any pipes across the front of the boiler thermostat
Diagram 4.2
DOMESTIC, PUMPED HEATING
pocket, controls or the combustion chamber cover.
Pipework must not be routed directly below the draught diverter,
across the boiler, but may be routed under the edges of the
draught diverter.
Notch on
4.4 Water Connections - Fully Pumped
DISTRIBUTOR must
Systems
lie within the shaded
area, BETWEEN
It is important that all connections are made as shown in
diagram 4.5.
TWO MARKERS
Fit suitable fittings into the boiler tappings as required, see
diagram 4.5.
The water distributor tube MUST be fitted into the return
connection, see diagram 4.3. The distributor tube is packed in
the top fitment.
Connect pipework into prepared fittings making sure that all
DISTRIBUTOR
pipes are taken backwards and will clear the casings, see
diagram 1.1. TUBE
must be in
When the front connections are used it is essential that any
pipework or fittings do not stick out more than as shown in pumped return
diagram 4.4.
connection
MARKERS
If only limited space is available, it is recommended that the front
Diagram 4.3
DISTRIBUTOR TUBE
connections are used.
9 221808B
1000
0873
0871
4 Installation
Fit plugs into all unused tappings.
'A'
Do not route any pipes across the front of the boiler thermostat
pocket, controls or combustion chamber cover.
VIEW ON ARROW 'A'
Pipework must not be routed directly below the draught diverter
across the boiler, but is allowed to be routed under the edges of
the draught diverter.
57 MAX.
(21/4in.)
4.5 Pump in Boiler Casing
BOILER
If the pump is to be fitted inside the boiler casing, position it as
shown in diagram 4.6 to either of the front connections.
There must be sufficient clearance X between the pump body
and the cleaning door to allow for removal of the door for flueway
cleaning.
4.6 Gas Connection
57 MAX.
Do not route the gas supply across the combustion chamber or
(21/4in.)
burner feed pipe. The gas feed must be along the right hand
side of the boiler.
PIPEWORK
Make the gas connection to the gas service cock.
CASING CLEARANCES Diagram 4.4
4.7 Flue Connection
ALTERNATIVE
The flue should be 100mm (4in) nominal diameter, refer to
Section 3 and diagram 1.1.
FLOW
POSITIONS
Fix and seal the flue to the hood in accordance with normal
practice.
ALTERNATIVE
RETURN
POSITIONS
With distributor
tube (not shown)
WATER CONNECTIONS FULLY
Diagram 4.5
PUMPED SYSTEMS
Clearance 'X' must be left to enable cleaning
door removal and boiler servicing
'X'
175
(7)
FLUEWAY
CLEANING
35 (13/8)
DOOR
ALTERNATIVE
R.H. FLOW
CONNECTION
L.H. FLOW
ISOLATING
CONNECTION
VALVES
Diagram 4.6
PUMP CLEARANCES
221808B 10
1524
0874
0875
5 Casing Location / Fitting
5.1 Side Vent Grille
No. 8
One vent grille is supplied with the boiler which can be fitted at
the rear of the left or right hand side casing. The grille is fitted
SCREW (2)
on the opposite side to any pipework connections.
Fit the grille, if required, to the side panel as shown in diagram
5.1 prior to fixing the side panel. The plastic pegs are a tight fit
and are best pushed home with a flat faced tool.
Do not use the grille if water connections are on both sides of the
boiler or if the boiler is screened by fixtures.
5.2 Side Casings
CASING
CASING
Fit side casing by locating their lugs into the lower slots in the
BRACKET
BRACKET
base tray, see diagram 5.2.
Secure the casing sides to the casing bracket at the front top.
PLASTIC PEG
SIDE VENT GRILLE
(If required, will fit to
left or right side casing)
BOILER
PLINTH
No. 8
SCREW (2)
SIDE CASING
(R.H. SHOWN)
LOCATING
LUG AND
SLOT
Diagram 5.2
SIDE CASINGS FITTING
Diagram 5.1
SIDE VENT GRILLE
6 Electrical Wiring
6.1 Control Box Cable Connection
Remove the screw and cover from the mains inlet connector,
COVER
see diagram 6.1.
Using heat resistant flexible cable of suitable length and rating,
as Section 1.6, connect the cable to the terminals in the
connector. Secure the outer sheathing with the clamp.
Engage slots and lugs, replace connector cover and secure
with screw.
Connect mains inlet connector to the control box and use three
of the cable clips, supplied loose, pushed on to the edge of the
L
left hand panel in positions CB as shown in diagram 6.2 to
E SLOTS
N
make sure that the cable does not touch any hot surfaces.
CABLE
6.2 Circulation Pump Cable Connection
CLAMP
LUGS
Heat resistant cable with a rating as stated in Section 1.6 must
be used for all wiring near the boiler, including the pump, if within
the boiler casing.
Support the pump cable away from hot surfaces if within the
boiler casing by pushing two cable clips, supplied loose, on to
the top edge of one side casing, as shown as P or AP in
Diagram 6.1
MAINS INLET CONNECTOR
diagram 6.2.
11 221808B
1018
0885
0878
6 Electrical Wiring
6.3 Flue Blockage Safety Device - Capillary
SAFETY DEVICE CAPILLARY
and Interrupter Electrical Leads
CLIP POSITION
For transit the capillary is taped to the side of the boiler.
230 (9)
Remove tape and place capillary into cable clips provided, see
P
diagram 6.2.
CB
AP
P
Note: Capillary must not touch the heat exchanger side.
CB
AP
Secure the interrupter electrical leads so as not to strain them, 230 (9)
25
see diagram 6.2.
(1)
Fit 2 pump cable
6.4 System Controls
clips at positions P.
The electrical installation must be in accordance with the
current issue of BS7671.
Alternative pump
The electrical isolator must isolate both the boiler and system
cable clips
controls.
(if feed is on the
CB
left hand side) at
6.5 Testing
positions AP.
Checks to ensure electrical safety should be carried out by a
competent person.
In the event of an electrical fault after installation of the boiler,
Fit 3 control
preliminary system checks must be carried out, that is, earth
box feed cable
continuity, polarity and resistance to earth as described in a
clips at
multimeter instruction book.
INTERRUPTER
positions CB.
ELECTRICAL
LEADS CLIP
Diagram 6.2
CABLE CLIP POSITIONS
7 Commissioning
fully pushed in for about 15 seconds. If the pilot fails to remain
Please ensure the Benchmark logbook is completed and left
alight, repeat lighting procedure, but now keep the control
with the user.
button pushed in for a little longer.
7.1 Commissioning and Testing the Boiler If the control knob A is turned to ' ', a safety device prevents
relighting in an unsafe condition. No attempt should be made
The whole of the system should be thoroughly flushed out with
to push knob A in until 3 minutes have gone by.
cold water with pump removed. Make sure that all valves are
Note: Should the boiler fail to operate correctly refer to the Fault
open. Refit the pump and fill the system. Examine for water
Finding - Section 10.
soundness and vent all air from the system, including the pump.
Make sure that the pilot is alight and stable, see diagram 7.3 for
Caution. The following should be done by a competent person.
flame length, switch on the electrical supply. Set any remote
Identify the controls, refer to diagram 7.1.
controls so that they are calling for heat. Turn control knob A
Check that the gas cock K is closed, that is, slot is horizontal. to ' ' main burner position. Set boiler thermostat control knob
B between MIN and MAX against the setting point on the
Open all windows and put out any naked lights, pipes or
control box, the main burner will light. MAX is about 82oC
cigarettes.
(180oF).
Purge air from the gas supply in accordance with the current
Test for gas soundness around boiler gas components with a
issue of BS6891.
suitable leak detection fluid.
Carefully unwind the thermostat capillary, insert the phial fully
Set the burner gas pressure required, ten minutes after lighting,
into pocket J and secure the location washer behind the
see Data label L for settings or refer to Section 1.2. Adjust
retaining split pin, supplied in the loose items pack, see diagram
screw F , diagram 7.1 to obtain the required heat input. Turn
7.2.
clockwise to decrease. After adjusting, seal the screw.
Check that the mains electrical supply is switched off.
If any doubt exists, the gas rate should also be checked at the
Set thermostat control knob B to O .
meter. This should be in the range of:
Remove gas test pressure point screw G and fit a suitable
Hideaway - 50 - 1.8 to 2.2m3/h 51 to 63ft3/h
pressure gauge.
The rates are for guidance only, depending on the heat setting.
Open gas cock K , slot vertical.
Stick the self adhesive arrow on to the data label against the
Note: Make sure the Flue Blockage Safety Device reset button
output the boiler is set to. The arrow is in the loose items pack.
'N' is fully pushed in.
Check the operation of the flame failure device as follows:
Turn gas control knob A to ' ' , the pilot and ignition position
With the main burner alight, turn the gas control valve knob A
and push in. At the same time press and release the ignition
fully clockwise to its stop ' ', the main and pilot flames will go
button C until the pilot lights. At this stage air may be present
out. Relighting will not now be possible. Before 60 seconds the
in the gas supply pipes and this operation may need to be
safety device will work, indicated by a click from the gas valve.
repeated. When the pilot burner lights, keep control knob A
221808B 12
0904
7 Commissioning
B
G
L A
F
J
C
H
SETTING
H
N
POINTS
A GAS CONTROL KNOB. J PHIAL POCKET.
B TERMOSTAT CONTROL. K GAS SERVICE COCK.
C PIEZO IGNITION BUTTON. L DATA BADGE.
E VIEWING WINDOW. N FLUE
E F BURNER GAS RATE BLOCKAGE
GAS CONTROL KNOB 'A' SAFETY DEVICE
K
(Shown ADJUSTMENT. RESET BUTTON.
closed)
G BURNER PRESSURE
TEST POINT.
H CONTROL BOX.
POSITIONS:-
= OFF = PILOT/IGNITION = MAIN BURNER
Diagram 7.1
BOILER COMPONENTS
Do not attempt to relight until three minutes have gone by.
Remove the pressure gauge and refit the pressure test point
THERMOSTAT
screw G , makes sure a gas tight seal is made.
CAPILLARY
Turn thermostat B to O and relight the pilot burner as above.
LOCATION
Relight the main burner as above.
WASHER
Check that the boiler thermostat and all remote controls are
working correctly.
Do not attempt to adjust the thermostat calibration screw.
Test the boiler for spillage of the flue products at the draught
diverter as detailed in the current issue of BS5440 Part 1. If an
extract fan is fitted in the premises, refer to Section 3.6.
PHIAL
7.2 Commissioning the System
POCKET
Allow the system to warm up and set the pump adjuster to a
design position which gives the correct temperature difference RETAINING
of 11oC (20oF) between the flow and return. There should be no
SPLIT PIN
undue noise in the system, pumping over or entry of air at the
open vent above the cold water feed and expansion cistern.
SECURING THE
Diagram 7.2
THERMOSTAT PHIAL
Allow the system to reach maximum working temperature and
examine for water soundness.
The system should then be drained down as rapidly as possible
to complete the flushing process.
The system should then be refilled, vented and examined for
water soundness.
13 221808B
1005
1870
7 Commissioning
7.3 Completion
Instruct and demonstrate the efficient and safer operation of the
boiler, heating and domestic hot water system.
STUD
UPPER
Hand the Instructions for Use to the user, for them to keep,
HOOK
making sure that they fully understand them.
DOOR
FASCIA
Advise the user that to ensure the continued efficient and safe
operation of the boiler is recommended that it is checked and
VIEW 1
serviced at regular intervals. The frequency of servicing will
depend upon the particular installation and usage, but in general
once a year should be enough.
PLINTH
Draw attention, if applicable, to the current issue of the Gas
FRONT
Safety (Installation and Use) Regulations, Section 35, which
imposes a duty of care on all persons who let out any property
containing a gas appliance.
LOWER
It is the law that servicing is carried out by a competent person.
HOOK
VIEW 2
Advise that the boiler is fitted with a Flue Blockage Safety
Device and refer to the Instructions for Use.
Reminder - Leave these instructions and the Benchmark
logbook with the user.
Fit the plinth front, by locating the sides over the boiler plinth
then lowering to engage the upper and lower hooks, see
VIEW 1
diagram 7.4.
Fit four plastic pegs into the required holes in the top panel, see
diagram 7.5. The plastic pegs are a tight fit and are best pushed
home with a flat faced tool.
Push the casing top on to all four side panel locations. From
inside the casing check that all the rivets have engaged into the
VIEW 2
holes.
Fit the door by locating the hooked runner at the bottom into the
Diagram 7.4
slots in side casings and pushing on to the studs on the side PLINTH / DOOR FITTING
casings, see diagram 7.4.
PLASTIC PEG (4)
TOP CASING
B
A
SIDE
A
B
CASING
(L.H.)
FLAME
DIMENSION
PEG POSITIONS IN TOP CASING
13 (1/2 in.)
A = FRONT EDGE FLUSH
VIEWING
APPROX.
B = 10mm (3/8 in) FRONT OVERHANG
WINDOW
AB
AB AB AB
PILOT
SIDE SIDE
BURNER
CASING CASING
ASSEMBLY
DOOR
DOOR
Diagram 7.3
FLAME DIMENSION Diagram 7.5
TOP CASING FITTING
221808B 14
0887
1180
1009
8 Servicing
Servicing must be carried out by a competent person.
Before servicing, turn off the gas supply at the boiler service
THERMOSTAT
cock, see diagram 8.1 and isolate the electrical supply to the
CAPILLARY
boiler.
LOCATION
Always test for gas soundness after completing a service and
WASHER
replacement of parts.
8.1 Boiler Flueways
Pull door forwards at the top to disengage the studs and lift to
release from slots, see diagram 7.4.
Lift plinth front up and forwards to withdraw, see diagram 7.4.
Disconnect the union on the gas service cock, see diagram 8.1.
PHIAL
Remove the mains inlet connector by pulling upwards, see
POCKET
diagram 8.1.
Withdraw the retaining split pin from the thermostat phial pocket
RETAINING
then withdraw the phial and capillary, see diagram 8.2.
SPLIT PIN
Remove electrical connections from the interrupter, see diagram
8.1. SECURING THE
Diagram 8.2
THERMOSTAT PHIAL
Remove the four screws retaining the combustion chamber
cover and burner assembly, see diagram 8.3. Withdraw
forwards the complete assembly of cover, control box and
burner.
Remove the graphite coated nut to release baffle tray and
remove the combustion chamber, taking care not to damage
the insulation material on the sides.
GRAPHITE
Remove the self-tapping screws which retain the cleaning door
COATED
and lift clear, see diagram 8.4.
NUT
Place a sheet of paper in the combustion chamber to catch any
flue debris.
Remove flueway baffles, see diagrams 8.7 and 8.8.
Thoroughly clean boiler flueways and fins with a suitable stiff
brush.
Replace in reverse order, after completing instructions in
BAFFLE
Section 8.2 and 8.3.
TRAY
Make sure that the thermocouple phial is at the bottom of its
SECURING
pocket and located by the washer being behind the retaining
COMBUSTION
SCREW (4)
split pin, leaving clearance between the capillary tube and
boiler, see diagram 8.2. CHAMBER COVER
Diagram 8.3
ACCESS FOR SERVICING
FLUEWAY
CLEANING
INTERRUPTER
MAINS INLET
DOOR
ELECTRICAL
CONNECTOR
CONNECTIONS
(pull upwards)
SELF-
TAPPING
SCREW (4)
GAS
SERVICE
COCK
UNION
TURN OFF
ISOLATION OF
ACCESS TO FLUEWAY Diagram 8.4
Diagram 8.1
GAS AND ELECTRICITY
15 221808B
1870
1010
0908
0907
8 Servicing
8.2 Burner and Injector
Locate venturi
Follow instructions to remove the front cover, burner and controls
lugs in burner BURNER
assembly as Section 8.1.
slots and twist GASKET
Remove the screw securing the lint arrester gauze to the
clockwise to
combustion chamber cover. Remove arrester by lifting slightly LOCKING
NUT
engage
and withdrawing forwards to clear gas pipe, thermocouple and
SLIDE
pilot tube, see diagram 8.5.
Remove the two burner securing nuts from the flange of the
burner supply pipe.
Remove the burner from the cover and supply pipe flange.
Slacken the nut securing the locking slide on the venturi right
side, disengage the slide to enable the venturi end of the burner
Twist VENTURI
to be twisted anticlockwise to disengage it from the burner body,
anti-clockwise
see diagram 8.6.
to disengage
Clean the burner parts and lint arrester thoroughly, using a from BURNER
vacuum cleaner. BODY
BURNER
Check the condition of the burner gasket. Reuse or replace the
gasket as necessary. Reassembly by locating the venturi lugs BODY
VENTURI
into the burner slots and twisting clockwise, see diagram 8.6.
Diagram 8.6
BURNER SERVICING
Check the main burner injector for blockage or damage and
replace as necessary, see Section 9.2.
When replacing lint arrester locate the two lugs into the slots on
the combustion chamber cover and locate around the feed pipe,
then secure with the screws.
8.3 Service Checks
Inspect the pilot burner, thermocouple and pilot burner, cleaning
as necessary. Check the condition of the parts. If necessary BAFFLE
remove the pilot shield by removing the securing screw and nut.
Check the condition of the side and rear insulation panels in the
combustion chamber.
Check the condition of the seals on the cleaning door and the
combustion chamber cover.
Replace all items in the reverse order, relight and test the boiler.
Replacement of parts should be carried out by a competent
person.
HEAT EXCHANGERS
Diagram 8.7
MAIN
COMBUSTION
INJECTOR
BURNER
CHAMBER
COVER
BURNER
SUPPLY
PIPE
PROTECTIVE
SLEEVING
BAFFLES
SLOT
SECURING
SECURING
NUT(2)
LINT
HEAT
SCREW
LUG
ARRESTER
EXCHANGERS
REMOVAL OF BURNER FROM
Diagram 8.5 Diagram 8.8
COMBUSTION CHAMBER
221808B 16
1033
6122
6126
1013
9 Replacement of Parts
MAINS INLET
GAS VALVE
CONNECTOR
GAS
SECURING
(Disconnect)
VALVE
SCREW
GAS VALVE
SECURING SCREW
ELECTRICAL
THERMOSTAT
CONNECTORS
CONTROL
COVER
KNOB
SECURING
SCREW
THERMOSTAT
SECURING
CONTROL BOX
SCREW (2)
COVER
PIEZO
UNIT
HOOK
ELECTRICAL
INTERRUPTER
CONNECTORS
ELECTRICAL
CONNECTIONS
SLOT
HALF UNION
PIPE
BURNER
IGNITION LEAD
SUPPLY
(BLACK END)
PIPE
THERMOCOUPLE
PILOT TUBE
Diagram 9.1
CONTROL BOX
Before removing or replacing any parts, turn off the gas supply
9.2 Boiler Thermostat
at the boiler service cock, see diagram 8.1. Isolate the electrical
Follow the relevant instructions in Section 8.1 and 9.1.
supply to the boiler.
Pull off the thermostat control knob.
Unless stated otherwise all parts are replaced in the reverse
order to removal. Remove the two screws which secure the boiler thermostat to
the control box, see diagram 9.1.
Always test for gas soundness after replacing parts.
Tilt the thermostat so that the electrical connections can be
removed.
9.1 Gas Valve
Withdraw boiler thermostat from control box complete with
Follow the relevant instructions in Section 8.1.
capillary tube and phial.
Remove control box cover by removing the screw and unhooking
Refer to diagram 9.2 to connect electrical connectors.
at the side, see diagram 9.1.
Replace the thermostat phial as the relevant part of Section 8.1.
Disconnect thermocouple nut, interrupter, electrical connections
and pilot tube connection at the gas valve.
9.3 Piezo Unit
Remove the two screws which secure gas valve to the control
box. Pull door forward at the top to disengage the studs and lift to
release from slots, see diagram 7.4.
Tilt control box to enable it to be lifted off the gas valve.
Remove mains inlet connector by pulling upward, see diagram
Unscrew half union pipe from gas valve.
8.1.
Unscrew the gas valve from the burner supply pipe.
Remove the control box cover by removing screw and unhooking
When screwing the pipes into the new gas valve use a little
from slot at the side, see diagram 9.1.
jointing compound on the external thread only, to make a gas
Disconnect the ignition lead at the piezo unit.
tight seal.
Remove the nut inside the control box and remove piezo unit.
Replace thermostat phial as relevant part of Section 8.1.
Refer to diagram 9.2 to connect electrical leads.
It will be necessary to purge the system of air after changing the
gas valve. Follow the instructions in Section 7.1.
17 221808B
6123
9 Replacement of Parts
240V~ 50Hz MAINS SUPPLY FUSED AT 3A
THERMOSTAT
N L GAS
VALVE
C N/C
RED
ORANGE
GREEN / YELLOW
BLUE
CHASSIS EARTH
Diagram 9.2
CONTROL BOX WIRING
9.4 Thermocouple
SECURING SCREW (2)
Remove the door and plinth from the front as relevant parts of
AND NUT (2)
Section 8.1.
THERMOCOUPLE
SPARK
Remove lint arrester as in Section 8.2.
ELECTRODE
Disconnect the thermocouple by unscrewing nuts at the gas
valve and pilot burner, see diagram 9.1 and 9.3. Release cable
IGNITION LEAD
clips and the thermocouple can be withdrawn.
(CLEAR END)
Do not tighten nut at gas valve more than a quarter turn beyond
finger tight.
Replace lint arrester as Section 8.2. PILOT
SHIELD
9.5 Spark Electrode
PILOT
Remove the door plinth as the relevant part of
PILOT TUBE
Section 8.2.
BURNER
PILOT
Remove the lint arrester as Section 8.2.
ASSEMBLY
INJECTOR
Disconnect the ignition lead, see diagram 9.3.
Disconnect the thermocouple nut and withdraw the thermocouple
from the pilot burner.
PILOT ASSEMBLY Diagram 9.3
Disconnect the nut retaining the spark electrode.
The spark gap dimension is shown on diagram 9.4.
9.6 Ignition Lead
Remove the door and plinth as the relevant parts of Section 8.1.
Remove the lint arrester as in Section 8.2.
Disconnect the ignition lead at the piezo unit, see diagram 9.1.
3-4 (1/8)
Disconnect ignition lead at the spark electrode, see diagram
SPARK
9.3.
GAP
When reconnecting the lead, make sure that the clear end is
fitted to the spark electrode and the protective sleeve is fitted
where the lead passes through the lint arrester, see diagram
8.5.
Diagram 9.4
SPARK GAP DIMENSIONS
221808B 18
6124
0935
1538
9 Replacement of Parts
9.7 Pilot Burner
ELECTRICAL
Follow the instructions in the relevant parts of Section 8.1 to
CAPILLARY
CONNECTIONS
remove cover and burner controls assembly.
Remove the lint arrester as in Section 8.2.
Disconnect the thermocouple nut at the pilot burner, see diagram
9.3.
Disconnect the nut retaining the pilot tube and injector in the
pilot burner.
FLUE
Remove the two screws and nuts securing the pilot burner and BLOCKAGE
the shield front cover, see diagram 9.3.
SAFETY
DEVICE
Check that the pilot flame length is as shown in diagram 7.3.
Replace thermostat phial as Section 8.1.
Replace lint arrester as Section 8.2.
9.8 Insulation Panels
Follow the relevant instructions in Section 8.1.
Unfasten the two screws retaining each side insulation panel
within the combustion chamber and remove panel, see diagram
SECURING
9.5.
LOCKNUT
Release the rear insulation panel upper clips and lift out panel.
Replace thermostat phial as Section 8.1.
9.9 Injector
When the burner has been removed from the injector manifold
as in Section 8.2 the injector can be unscrewed from the
manifold and renewed as necessary.
When replacing use a little jointing compound on the external
threads only, to make a gas tight seal.
Diagram 9.6
ELECTRICAL CONNECTIONS
Replace thermostat phial as Section 8.1.
CABLE CLIPS(2)
CAPILLARY
REAR
SIDE
INSULATION
INSULATION
PANEL
PANEL
CLIP
FLUE
BAFFLE
BLOCKAGE
TRAY
SAFETY
SCREW
DEVICE
GRAPHITE
COATED
NUT
Diagram 9.5 CAPILLARY REMOVAL Diagram 9.7
INSULATION PANELS
19 221808B
5041
0904/A
1670
9 Replacement of Parts
9.10 Flue Blockage Safety Device
Gain access as Section 8.1.
Remove the electrical connections, see diagram 9.6
Remove capillary from cable clips, see diagram 9.7.
To remove the phial assembly, first gain access through flue
cleaning door as Section 8.1.
LOCATION STUD
Unscrew securing nut and withdraw the phial assembly from the
SECURING
location stud, see diagram 9.8.
NUT
Remove the safety device securing locknut complete with phial
assembly, see diagram 9.6.
PHIAL
PHIAL ASSEMBLY
Diagram 9.8
PHIAL ASSEMBLY REMOVAL
10 Fault Finding - Electrical
10.1 Electrical
Refer to functional flow diagram 10.1, electrical fault finding
chart, diagram 10.2 and wiring diagram 9.2.
IMPORTANT. The preliminary electrical system checks
contained in a multimeter instruction book are the first checks
to be carried out during and fault finding procedure. On
completion of the service fault finding task which has required
the breaking and remaking of electrical connections then checks.
earth continuity, polarity and resistance to earth must be
repeated.
L
10.2 Thermocouple
To test the thermocouple a meter with a range 0 to 30mV is
THERMOSTAT
GAS VALVE
required together with a thermocouple interrupter test unit
CONTROL
similar to the British Gas Multimeter and interrupter.
SOLENOID
Refer to thermocouple fault finding chart, diagram 10.3 and
4
3
diagnosis graph, diagram 10.4.
N/C
C
10.3 Pilot and Ignition
Refer to pilot and ignition fault finding chart, see diagram 10.6
and 10.3.
10.4 Flue Blockage Safety Device
If the device operates it indicates there is a problem with the
ORANGE
chimney. Make sure that the air vents are free from obstruction.
Carry out spillage checks as BS5440 Part 1 and put right as
necessary.
N
RED
FUNCTIONAL FLOW WIRING
Diagram 10.1
221808B 20
6298
0900
BLUE
10 Fault Finding - Electrical
Carry out preliminary electrical checks to
make sure the electrical supply is available
at the boiler. Check that external controls
are calling for heat. Make sure that the
system is filled, the flue blockage safety
device is reset, the gas supply is available
and the pilot is lit.
Isolate electrical supply to the
control box.
Remove the control box cover and
check all cables.
Turn boiler thermostat to Max.
NO
Is there continuity between
'C' and 'NC'.
YES
Faulty thermostat.
Replace.
Turn boiler thermostat to 'O'.
NO
Is there open circuit between 'C'
and 'NC'.
YES
Restore electrical supply with pilot
NO
burner lit and boiler thermostat set
between 'MIN' and 'MAX', does the
main burner light.
YES
Faulty gas valve.
Replace.
NO
Turn boiler thermostat to "O'.
Does main burner extinguish.
YES
Boiler controls in order.
ELECTRICAL FAULT FINDING
Diagram 10.2
21 221808B
0899/A
10 Fault Finding - Thermocouple
With the boiler cold, check connections of the thermocouple, boiler flue blockage safety device
and gas valve. Reset flue blockage safety device.
Disconnect flue blockage safety device connectors at points A and B at the gas valve,
see diagram Interrupter Electrical Connections.
Test continuity of the flue blockage safety device. Is there continuity?
NO
YES
Faulty boiler flue blockage
safety device, renew.
Re-connect boiler flue blockage
safety device to points A and B.
Disconnect thermocouple at
YES Faulty flue blockage safety device
connection point D of the gas valve.
connectors into gas valve,
Test continuity between point C and the
either at A or C.
body of the gas valve.
Renew where faulty.
Is there continuity?
NO
Test continuity of thermocouple between inner
NO
connection point D and point E.
Faulty thermocouple, renew.
Is there continuity?
YES
Thermocouple and boiler flue blockage
safety device circuit satisfactory.
THERMOCOUPLE AND FLUE BLOCKAGE SAFETY DEVICE
FAULT FINDING Diagram 10.3
FLUE BLOCKAGE SAFETY DEVICE
GAS VALVE
29
27
25
CONNECTION "A"
23
CONNECTION "E"
21
ABC
19
CONNECTION "B"
17
15
POINT "C"
13
11
CONNECTION "D"
9
0 2 4 6 8 10 12 14 16 18 20 22
Closed Circuit Voltage (millivolts)
INTERRUPTER ELECTRICAL
DIAGNOSIS GRAPH FOR
CONNECTIONS
Diagram 10.5
Diagram 10.4
THERMOCOUPLE CIRCUIT
221808B 22
2327/B
5031
1546
Open Circuit Voltage (millivolts)
10 Fault Finding - Pilot
START HERE
Check gas line - open all cocks,
rectify any blockages, purge out
any air. Check flue blockage
safety device is reset,
Does pilot stay alight when
check all thermocouple circuit
gas valve knob is released?
connections are clean and in good
condition. Does pilot light?
NO YES NO YES
Apply match to pilot burner instead
of pressing piezo unit button. PILOT SATISFACTORY
Does pilot light?
NO YES
Undo tubing nut at pilot burner. Does pilot flame
Press gas valve knob. envelope thermocouple?
Does gas flow freely?
NO YES NO YES
Rectify blockage in pilot injector, Check aeration. If necessary -
or renew pilot injector. Clean pilot, rectify blockage in
pilot injector, or replace.
Undo tubing nut at pilot outlet of Check thermocouple circuit using
gas valve. Press gas valve knob. Thermocouple Fault - Finding
Does gas flow freely? diagram.
NO YES
On pressing piezo unit button
Change blocked pilot tube. is there a spark across
electrode gap?
NO YES
Pull ignition lead off electrode.
Change gas valve. Hold end of lead close to pilot
burner and operate piezo unit.
Is there a spark across gap?
NO YES
Pull ignition lead off piezo unit.
Using blade of a screwdriver,
touch unit chassis and leave
approx. 4mm gap from connection
tag on piezo unit. Operate piezo.
Is there a spark across gap?
NO YES
Change Change
piezo unit. ignition unit.
Check electrode gap. Reposition,
or replace electrode as necessary.
Diagram 10.6
PILOT / IGNITION FAULT FINDING
23 221808B
0905A
11 Spare Parts
11.1 Part Identification 11.2 Ordering
The key number in the first column of the list will help identify When ordering spare parts quote the part number and
each part shown in diagram 11.1. description, stating the model and serial number off the data
label L , see diagram 7.1.
If ordering from British Gas also quote the GC appliance
number off the data label and the required spare part GC
number.
1
2
3
4 12
6
5
8
11
9
10
7
Diagram 11.1
Key No Part No Description GC Part No
1 425568 Electrical control box assy 312 451
2 203329 Gas control valve 384 345
3 205752 Injector - 50
4 203414 Pilot burner assy 312 246
5 203508 Injector - pilot 395 674
6 900001 Thermocouple c/w nut
7 202571 Thermostat c/w screws
8 FF2228 Control knob assy 355 241
9 900501 Piezo unit 382 585
10 WW4613 Ignition lead 136 399
11 202605 Spark Electrode 395 720
12 425794 Flue Blockage Safety device E02686
Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.
221808B 24
6125
Wyszukiwarka
Podobne podstrony:
Glow Worm installation and service manual Hideaway 60CF UISGlow Worm installation and service manual Hideaway 100CF UISGlow Worm installation and service manual Hideaway 50BF UISGlow Worm installation and service manual Hideaway 80CF UISGlow Worm installation and service manual Hideaway 80BF UISGlow Worm installation and service manual Ultimate 50CF UISGlow Worm installation and service manual Hideaway 70CF UISGlow Worm installation and service manual Hideaway 70BF UISGlow Worm installation and service manual Hideaway 40BF UISGlow Worm installation and service manual Hideaway 120BF UISGlow Worm installation and service manual Hideaway100BF UISGlow Worm installation and service manual Hideaway 40CFGlow Worm installation and service manual Hideaway 120CF UISGlow Worm installation and service manual Energy Saver 40 UIGlow Worm installation and service manual Ultimate 60CF UISGlow Worm installation and service manual Energy Saver 60 UIGlow Worm installation and service manual Glow micron 40Glow Worm installation and service manual Ultimate 60BF UISGlow Worm installation and service manual Miami GF UISwięcej podobnych podstron