{Prog Comments ****}
{
02/20/95 [ws]
M751.00.00
Initial creation from M703.82.16
removed all settting of Cycle Parameter Values
changed final M30 to M26M02
added tool prep of the first tool used in the last tool change.
}
{
x/x/95 [ws]
Cin Acr A2100-Lancer M751.00.01 (from M751.00.00)
}
{3/25/96, Updated to .12 format as per Fanuc 6M M001.12, did not add support for MasterOp, MPK}
{04/02/98,
Initial: Cin Acr A2100-Sabre M751.12
Created: Cin Acr A2100-Sabre M751.12.1
Changes to Prog:
1) FORMATted TrackZNO#.
CDH}
{Prog Numeric Format Definitions ****}
#1 = '#.00'
#2 = '###.###;0'
#3 = '*###.###;0'
#4 = '####.####;0'
#5 = '#######0'
#6 = '##.##;0'
#7 = '0000'
#8 = '+####.####;0'
#9 = '####0'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CP1LessCP2#,4)
FORMAT(ABS#,4)
FORMAT(ADD#,4)
FORMAT(SUB#,4)
FORMAT(CalcZSurf#,4)
FORMAT(ClearancePlane1#,4)
FORMAT(ClearancePlane2#,4)
FORMAT(Retract#,4)
FORMAT(ToolDiameter#,4)
FORMAT(TrackZNO#,4)
FORMAT(Repeats#,5)
FORMAT(Tag#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(Program#,7)
FORMAT(HelixPitch#,8)
FORMAT(Program#,9)
{Prog Subroutines ****}
{***** CMI specific Subroutines *****}
ToolCRCOfst:
IF CutterRadiusCompensation?
'D' ToolOffset# 'O' CRCOffset#
ELSE
'D' ToolOffset#
END
RETURN
CMIPreTool:
IF NOT LastTool?
FORMAT(ADD#,7)
'T' NextTool# { PreTool }
FORMAT(ADD#,4)
END
RETURN
CMI_Wvalue:
IF RetractToCP1?
IF NotEqual? SUB# ClearancePlane1# CalcZSurf# Num#('0')
IF GreaterThan? SUB# ClearancePlane1# CalcZSurf# Num#('0')
'W' SUB# ClearancePlane1# CalcZSurf#
END
END
ELSE
IF NotEqual? SUB# ClearancePlane2# CalcZSurf# Num#('0')
IF GreaterThan? SUB# ClearancePlane2# CalcZSurf# Num#('0')
'W' SUB# ClearancePlane2# CalcZSurf#
END
END
END
RETURN
{***** End A2100 specific Subroutines *****}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoSubComment:
IF UseComments? AND SubComment?
'(MSG, "SUB NUMBER: ' Tag# '" )' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'(MSG, "OPERATION ' Operation# ': ' OperationType$ '" )' EOL
END
IF OperationComment?
'(MSG, "' OperationComment$ '" )' EOL
END
IF WorkGroupComment?
'(MSG, "' WorkGroupComment$ '" )' EOL
END
IF ToolTypeComment?
'(MSG, "TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ '" )' EOL
END
IF ToolComment?
'(MSG, "' ToolComment$ '" )' EOL
END
RestoreScale
END
RETURN
DoCoolOn:
IF ThruSpin?
'M27'
ELSE
CoolOn {M8}
END
{ To Be Used When Support is Added for additional Coolant Types and CMI says what the M codes mean
There is also a 5th Coolant Type they want supported M7
_________________________
IF Pulse?
'M28'
ELSE
IF Mist?
'M29'
ELSE {Flood}
CoolOn {M8}
END
END
END
__________________________
}
RETURN
PSInit:
RotateF
OptCyc1F { ??? }
ResetCool
RETURN
GetIndex:
IF FourthCW?
FORMAT(FourthDegree#,2)
'A' FourthDegree#
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
'A' FourthDegree#
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
'B' FifthDegree#
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
'B' FifthDegree#
FifthCCWF {reset flag}
END
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
SeqLabC GetIndex EOL
NextPS
RETURN
DoLastEndOpPS:
PSInit
NEXT EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
SeqLabC GetIndex EOL
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqLabC Feed ZIn FeedEnt EOL
ELSE
SeqLabC RapidC ZIn EOL
END
RETURN
StartSub:
OpenSub
'(DFS,L' Tag# ')' EOL
DoSubComment
RETURN
SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'(MSG, "WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT" )' EOL
' ' EOL
END
END
RETURN
StdSub: {not used in Virtual, only used in non SepSub Repeats}
SeqLabC 'G10=[T2]V0' EOL {sets temporary register #2 to 0}
SeqLabC 'Q' Tag# '1' EOL {branch label 1}
SeqLabC '(CLS,L' Tag# ')' EOL {call subroutine}
SeqLabC 'G10=[T2]V[T2]+1' EOL {increment register #2 by 1}
SeqLabC 'G11E[T2]=' Repeats# 'L' Tag# '2' EOL {if register #2 is equal to number of repeats then jump to branch label 2}
SeqLabC 'G11L-' Tag# '1' EOL {jump backwards to branch label 1}
SeqLabC 'Q' Tag# '2' EOL {branch label 2}
StartSub
RETURN
FinishSub1: {part 1}
SeqLabC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN
FinishSubG92: {part 2}
SeqLabC Preset ShiftRC EOL
SeqLabC '(ENS)' EOL
CloseSub
SeqLabC Preset UnshftRC EOL
RETURN
OpenMP:
{TagInc}
IF WorkFixtureOffsets?
ELSE
'(Non-WFO Multiple parts, Long Hand not supported in this post)' EOL
END
RETURN
CloseMP:
IF WorkFixtureOffsets?
ELSE
'(Non-WFO Multiple parts, Long Hand not supported in this post)' EOL
END
RETURN
SubCSMP:
RETURN
SetZRepInc: {rep change 10}
IF Flag?('1') AND ZMove? AND AbsoluteMoves?
IncValue
SetFlag('2')
END
RETURN
DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLabC AbsValue EOL
END
RETURN
ckHMove:
SetStatusOff
SetFlagF('9')
IF YZPlane?
IF NotEqual? SUB# SPY# ArcI# SUB# ArcI# EPY#
SetFlag('9')
END
ELSE
IF NotEqual? SUB# SPX# ArcI# SUB# ArcI# EPX#
SetFlag('9')
END
END
SetStatusOn
RETURN
ckVMove:
SetStatusOff
SetFlagF('9')
IF XYPlane?
IF NotEqual? SUB# SPY# ArcJ# SUB# ArcJ# EPY#
SetFlag('9')
END
ELSE
IF NotEqual? SUB# SPZ# ArcJ# SUB# ArcJ# EPZ#
SetFlag('9')
END
END
SetStatusOn
RETURN
ckMove:
IF NOT FullArc?
IF XYPlane? AND NOT ZMove?
IF NOT XMove?
ckVMove
ELSE
IF NOT YMove?
ckHMove
END
END
ELSE
IF XZPlane? AND NOT YMove?
IF NOT XMove?
ckVMove
ELSE
IF NOT ZMove?
ckHMove
END
END
ELSE
IF YZPlane? AND NOT XMove?
IF NOT YMove?
ckVMove
ELSE
IF NOT ZMove?
ckHMove
END
END
END
END
END
END
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
IF XYPlane?
IF ZMove?
MoveX MoveY MoveZ ArcIJ 'K' HelixPitch#
ELSE
MoveX MoveY ArcIJ
END
ELSE
{ ??? what about incr subs here ??? }
IF XZPlane?
IF YMove?
MoveX MoveY MoveZ ArcIJ 'J' HelixPitch#
ELSE
MoveX MoveZ ArcIJ
END
ELSE { YZPlane }
IF XMove?
MoveX MoveY MoveZ ArcIJ 'I' HelixPitch#
ELSE
MoveY MoveZ ArcIJ
END
END
{ ??? }
END
RETURN
CkCRC:
IF LastFeat? { Exit Length Feature }
CRCOffC
ELSE
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
CRCOnC
END
END
RETURN
StdLine: {enables CRC on first call}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC DoAbsOrInc FeedC CkCRC MoveXYC MoveZC FeedRateC EOL { CRCOffsetC }
DecelMove2
END
SeqLabC DoAbsOrInc FeedC CkCRC MoveXYC MoveZC DecelFeed EOL { CRCOffsetC }
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc FeedC CkCRC MoveXYC MoveZC FeedRateC EOL { CRCOffsetC }
END
END
RETURN
ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqLabC MoveSXYC EOL
SeqLabC '(CLS,L' Tag# ')' EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
IF Drilling?
IF SPXMove? OR SPYMove? OR SPZMove?
SeqLabC DoDrillAbsOrInc MoveSXYZC
CMI_Wvalue
EOL
END
ELSE
SeqLabC DoDrillAbsOrInc MoveSXYZC EOL
END
END
ELSE
IF RapidFeat?
IF AutoCycle?
IF LastFeat?
CRCOffC
END
SeqLabC DoAbsOrInc RapidC MoveXYC MoveZC EOL
ELSE
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC
END
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc RapidC MoveXYC MoveZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle?
IF LastFeat?
SeqLabC DoAbsOrInc CRCOffC FeedC MoveXYC MoveZC FeedRateC EOL {MoveXYC SetZRepInc MoveZC, was MoveXYZC}
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLabC DoAbsOrInc FeedC MoveXYC MoveZC FeedRateC EOL {MoveXYC SetZRepInc MoveZC, was MoveXYZC}
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
ckMove
IF Flag?('9')
SetFlagF('9')
StdLine
ELSE
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC DoAbsOrInc FormatArc ArcFeedC EOL
DecelMove2
END
SeqLabC DoAbsOrInc FormatArc DecelFeed EOL
ELSE
SeqLabC DoAbsOrInc FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
IF LastFeat? AND CutterRadiusCompensation? AND NOT AutoCycle?
CRCOffC
IF NOT EmptyLine?
SeqLabC DoAbsOrInc LastFeatExtend EOL { ??? any zmoves ??? }
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN
AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLabC IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
ToolPath
SeqLabC AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{removed RapidC}
{removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqLabC '(ENS)' EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN
AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN
Milling:
IF AutoCycle?
TagInc
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN
G92Sub:
SubWarning
StdSub
SeqLabC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN
ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
TagInc
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Feed IncValue StrtPosC EOL
SeqLabC AbsOrInc
ELSE
SeqLabC Feed
END
ELSE
SeqLabC Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqLabC AbsOrInc ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqLabC Rapid ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLabC '(CLS,L' Tag# ')' EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqLabC Feed ZCP2 FeedEnt EOL
ELSE
SeqLabC Rapid ZCP2 EOL
END
END
SeqLabC '(ENS)' EOL
CloseSub
{Element shift, not pattern}
RETURN
ZonlyRep:
SetFlag('1') {std sep sub Zreps are in effect}
EachCycle
IF NOT FirstCycle?
SeqLabC Connect StrtPos EOL {added Connect}
END
IF FeedConnect?
SeqLabC FeedC ZInPlusInc FeedEnt EOL {changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqLabC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC RapidC ZInPlusInc EOL {added Rapid, reads better} {changed to RapidC, reads better}
END
END
TrackZNO# FIRST SPZ#
ToolPath
IF NOT FeedConnect?
IF AutoCycle?
SeqLabC ZCP3C EOL
ELSE
IF FIFO?
SeqLabC FeedC ZCP3C FeedEntC EOL
ELSE
SeqLabC RapidC ZCP3C EOL
END
END
END
NextCycle
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
SetFlagF('1') {not std sep sub Zreps in effect} {rep change 2}
UseSeparateSubCalls
SetMaxSeparateSubCalls('500')
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN
SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
OpGuts:
IF Milling?
SeqLabC ZCP2C EOL
IF Repeats?
TagInc
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') {std sep sub Zreps are in effect} {rep change 2}
ZonlyRep {rep change 1}
SetFlagF('1') {not std sep sub Zreps in effect} {rep change 3}
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqLabC ZCP3C EOL
ELSE
IF FIFO?
SeqLabC FeedC ZCP3C FeedEntC EOL
ELSE
SeqLabC RapidC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
TagInc
StdSub
SeqLabC AbsOrInc Rapid StrtPos EOL
END
EOL
{SeqLabC DrillCP EOL}
GetCycle
IF FIFO? AND Dwell? { Bore/Ream with Dwell }
SeqLabC PlaneC 'G89'
ELSE
IF Tap? AND OptCyc1?
SeqLabC PlaneC 'G84.1'
ELSE
SeqLabC PlaneC Cycle
END
END
StrtPos
'Z' Sub# Add# ClearancePlane2# Zdepth# CalcZSurf# { Z = tip depth - Top Surface}
'R' CalcZSurf#
CMI_Wvalue
IF Peck?
IF NotEqual? Peck# Num#('0')
'K' ABS# Peck#
END
END
FeedEnt
IF Peck?
IF PeckFullRetract?
IF GreaterThan? Peck# Num#('0')
'J13'
ELSE
'J3'
END
ELSE {Chip Break}
IF GreaterThan? Peck# Num#('0')
IF GTEqual? Retract# Num#('0')
'J11'
ELSE
'J12'
END
ELSE
IF GTEqual? Retract# Num#('0')
'J1'
ELSE
'J2'
END
END
END
ELSE
{
IF Tap? AND OptCyc1?
'J1'
END
}
END
EOL
TrackZNO# FIRST SPZ#
ToolPath
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SetDrillEndOpZ
SeqLabC DrillOff
IF RetractToCP1?
'R' ClearancePlane1#
ELSE
'R' ClearancePlane2#
END
EOL
SeqLabC Rapid ZCP3 EOL
IF Repeats?
FinishSubG92
END
END
END
SetFlagF('1') {not std sep sub Zreps in effect} {rep change 3}
RETURN
NotSameToolWFO:
IF NeedWFO1?
'H' NewWFO#
END
RETURN
SameToolWFO:
RETURN
InitOp:
'(PGM, '
IF ProgramComment?
'NAME="' ProgramComment$ '",'
ELSE
'NAME="' PartName$ '",'
END
IF GTEqual? Program# Num#('0')
' ID="' Program# '",'
END
' TYPE="A2100_274" )'
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
':G17G70G90' EOL
'(MSG, "PART: ' PartName$ '" )' EOL
IF ProgramNameComment?
'(MSG, "PROGRAM: ' ProgramName$ '" )' EOL
END
IF ProgramComment?
'(MSG, "' ProgramComment$ '" )' EOL
END
IF FormatNameComment?
'(MSG, "FORMAT: ' FormatName$ '" )' EOL
END
IF TimeComment?
'(MSG, "' Date$ ' AT ' Time$ '" )' EOL
END
IF MovesComment?
'(MSG, "OUTPUT IN ' MoveType$ ' INCHES" )' EOL
END
IF PartsComment?
'(MSG, "PARTS PROGRAMMED: ' Parts# '" )' EOL
END
IF StartToolComment?
'(MSG, "FIRST TOOL NOT IN SPINDLE" )' EOL
END
END
OpenSub
RestoreScale
RETURN
FirstOp1:
DoOpComments
':?' Plane 'G70' AbsOrInc Rapid { Inch }
FORMAT(ADD#,7)
'T' Tool# ToolChng EOL
FORMAT(ADD#,4)
RETURN
FirstOp2:
RETURN
FirstOp3:
CheckPass
SeqLabC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
FirstOp3a: {can't XY position before WFO}
CheckPass
SeqLabC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
FirstOp3b:
CheckPass
SeqLabC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn NotSameToolWFO EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
NewToolOp1:
RETURN
NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SeqLabC AbsOrInc Rapid Home EOL
END
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END
RETURN
NewToolOp3: {Start new Operation}
DoOpComments
':?' Plane 'G70' AbsOrInc Rapid { Inch }
FORMAT(ADD#,7)
'T' Tool# ToolChng EOL
FORMAT(ADD#,4)
RETURN
NewToolOp4:
RETURN
NewToolOp5:
CheckPass
SeqLabC PlaneC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
NewToolOp5a:
CheckPass
SeqLabC PlaneC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
NewToolOp5b:
CheckPass
SeqLabC PlaneC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn NotSameToolWFO EOL
SeqLabC DoCoolOn EOL
DoPostScript
RETURN
SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqLabC SpinOff EOL
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
IF NewToolOffset? OR ChangeCS?
{ ??? due full up here ??? }
END
END
RETURN
SameToolOp2: {Start new Operation}
DoOpComments
':?' Plane 'G70' AbsOrInc Rapid { Inch }
FORMAT(ADD#,7)
'T' Tool# ToolChng EOL
FORMAT(ADD#,4)
CheckPass
RETURN
SameToolOp3: {Start new Operation}
SeqLabC PlaneC Rapid StrtPos ToolCRCOfst Speed SpinOn NotSameToolWFO EOL
SeqLabC DoCoolOn EOL
DoPostScript
{ Old way of handling the SameToolOp3 routine
IF LAST ProgStop?
SeqLabC PlaneC Rapid StrtPos ZCP1 ToolCRCOfst Speed SpinOn EOL
SeqLabC DoCoolOn EOL
ELSE
IF NewToolOffset? OR ChangeCS?
SeqLabC PlaneC Rapid StrtPos ZCP1 ToolCRCOfst SpeedC EOL
ELSE
SeqLabC PlaneC Rapid StrtPos ToolCRCOfst SpeedC EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC DoCoolOn EOL
END
END
}
RETURN
End1:
RETURN
End2:
DoLastEndOpPS
IF FIRST ToolChangeAtHome?
SeqLabC AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
SeqLabC 'M0' EOL
END
RETURN
End3:
SeqLabC 'M26M02' EOL { End of Program }
CloseSub
Post2 {organize Subs into one program}
IF UseComments?
SetScale('1') {restore scale for comments}
IF FileBytesComment?
'(MSG, "FILE LENGTH: ' FileBytes# ' CHARACTERS" )' EOL
END
IF FileFeetComment?
'(MSG, "FILE LENGTH: ' FileFeet# ' FEET" )' EOL
END
IF FileMetersComment?
'(MSG, "FILE LENGTH: ' FileMeters# ' METERS" )' EOL
END
END
{ EOR EOL }
Close
ReTag
RETURN
MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
OpenMP
NewWFO
EachWFO {simple eachPart, ***start loop}
SeqLabC SetWFO EOL
IncWFO
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
SubCSMP
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
IF LastOP?
End1 {End of program}
End2
CloseMP
NextWFO {simple NextPart**** end loop}
SeqLabC WFO1 EOL
END
NextOp {loops back to EachOP until last Operation}
End3
RETURN
MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
OpenMP
NewWFO
EachWFO {simple eachPart, ***start loop}
SeqLabC SetWFO EOL
IncWFO
FirstOp3
ELSE
IF NewTool?
NewToolOp1
CloseMP
NextWFO {simple NextPart**** end loop}
SeqLabC WFO1 EOL
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
OpenMP
NewWFO
EachWFO {simple eachPart, ***start loop}
SeqLabC SetWFO EOL
IncWFO
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
IF LastOP?
End1 {End of program}
CloseMP
NextWFO {simple NextPart**** end loop}
SeqLabC WFO1 EOL
END
NextOp {loops back to EachOP until last Operation}
End2
End3
RETURN
MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3a
OpenMP
NewWFO
EachWFO {simple eachPart, ***start loop}
SeqLabC SetWFO EOL
IncWFO
SeqLabC StrtPos EOL
ELSE
IF NewTool?
CloseMP
NextWFO {simple NextPart**** end loop}
SeqLabC WFO1 EOL
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
NewToolOp5a
OpenMP
NewWFO
EachWFO {simple eachPart, ***start loop}
SeqLabC SetWFO EOL
IncWFO
SeqLabC StrtPos EOL
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
IF LastOP?
CloseMP
NextWFO {simple NextPart**** end loop}
SeqLabC WFO1 EOL
END
NextOp {loops back to EachOP until last Operation}
End1
End2
End3
RETURN
NoMPs: {no multiple parts}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3b
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5b
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolWFO
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN
{Start of executable Prog, top level ****}
ProgStart {setup and initializations}
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
Wyszukiwarka
Podobne podstrony:
Cin Acr 850SX Sabre C689 12Acr A2100 Sabre 750 BM MV50 12Acr A2100 Sabre [BL] MU64 12Cin Acr A2100 C703 12 1mCin Acr 850SX Sabre PM689 17 3Cin Acr 900MC [ABB] DU62 12Acr A2100 [DC] MQ56 12 1Acr A2100 [RPM] NMT09 12Cin Acr 950MC [WP] CU37 12 2Cin Acr A2100 [TVR] M875 82 6więcej podobnych podstron