ENG-02042601-T 1/14
Power Supply description and trouble shooting procedure
In general, switching regulators, using a switching transistor, switches on and off a DC
power supply through a transformer. When the transistor is turned on, the transformer
charges from the DC supply. When the transistor is turned off, the transformer
discharges into its secondary windings. These secondary outputs are then rectified
and filtered for use. Thus by controlling the transformer s charging time and
discharging time, it is possible to control (regulate) the secondary voltage efficiently.
In televisions using the FA, and FK, FV, GV, and GR chassis: the power supply uses an
integrated switching regulator circuit (IC), STR-F . This switching regulator
IC contains an oscillator (mono-stable), a switching transistor, protection circuits, etc.
The IC s internal circuits are protected against over voltage, over current, and over
heat. An internal block diagram of the IC is shown below.
Internal Circuits
V IN
4
GND
OVP
D
3
5
TSD
VCC
Start Up OVP Latch DRV
Q1 4
S
2
Osc
Pre Reg OCP/FB
1
S
DRV
3
Ref1
Osc.
T.S.D
D
2
Ref2
Ocp/FB
1
STR-F6514/5
GND
5
Startup circuit:
In order for the regulator to function, the IC has to start functioning. For this purpose,
from the unregulated supply, a start up voltage is supplied to the IC s power input.
Pre regulator:
The supply for the internal components of the IC is usually the unregulated supply.
This could vary and affect the performance of the IC. An internal regulator is used to
prevent drifting of IC s parameters due to the unregulated supply voltage variation.
OVP (Over Voltage Protection):
As mentioned earlier, the power supply to the IC is from the unregulated source. This
voltage can vary with the line voltage. Excessive voltage can cause damage to the IC.
The Over Voltage Protection circuit monitors the IC s supply voltage. If this voltage
JVC Television Power Supply Training Page 1
ENG-02042601-T 2/14
exceeds approximately 22Volts, this circuit turns off the IC s drive circuits. The OVP
circuit triggers an internal latch. See the internal block diagram
OCP (Over Current Protection);
The IC contains a power output FET. The current through this FET depends on
different factors such as on time, load on the power supply, etc. Excessive current
through the FET can damage it. Using a source resistor, the FET s current is
monitored. This proportional voltage is then fed back to the IC s OCP circuit. This
voltage, when exceeds the specified limit (0.75 V), the OCP circuit turns off the IC s
output FET.
TSD (Thermal Shut Down):
The IC is protected against over voltage and over current as discussed earlier. Besides
these protections, the IC is protected against over-heat-damage using the thermal shut
down circuit. When the IC s temperature reaches a certain limit, the thermal shut
down circuit operates and turns it off. TSD circuit triggers an internal latch.
Latch
The OVP circuit or the TSD circuit is activated, it then turns off the IC and also
trigger an internal latch. This latch circuit holds the IC s output circuit off. In order to
release the latch and turn on the FET again, IC s power must be removed and
reapplied.
Oscillator
This IC has an internal mono-stable oscillator (time constant circuit). After power is
applied, or the FET is turned off by OCP (see description above), the internal time
constant circuit will turn on the FET again after approximately 45 microseconds. If
required, it is possible to speed up the time constant circuit and turn on the FET
earlier than the internal time constant. We will discuss this later in detail.
Drive
As discussed earlier, the switching regulator IC has a power FET. All the control
circuits for the FET are applied to its drive circuit.
Pin Descriptions
Pin1, OCP/FB:
This pin has two functions.
" OCP
When a DC (above 0.75V) is applied to this pin; the IC s internal FET will be turned
off. After the applied DC is removed, depending on the internal time constant, the IC
will turn on the FET again.
" FB
In some applications it might be necessary to turn on the FET earlier than the time
decided by the internal time constant. In this case, it is possible to speed up the
internal time constant and turn on the FET by raising its pin1 DC above 1.4V and
then lowering it below 0.7V.
Pin 2, S
This is the Source of the IC s internal power FET. When the FET starts conducting,
the source resistor generates a source voltage, which is used to monitor the FET s
current. When this voltage exceeds a specified limit (approximately 0.75V), it then
JVC Television Power Supply Training Page 2
ENG-02042601-T 3/14
turns off the FET. After the FET is turned off, as discussed earlier, the FET will turn
on again. This is how we get the switching function
Pin 3, Drain
This is the internal power FET s drain. In a switching power supply application, the
drain is usually connected to the DC source through the switching transformer s
primary winding.
Pin 4, VIN
This pin has two functions
" Vcc
The DC supplied to this pin is routed through an internal regulator for powering
the IC s internal control circuits. The internal circuits will operate if the supply
voltage is between 16.0 and 22.0 V
" OVP
The DC supplied to this pin is also applied to an over voltage detector. If the
applied voltage exceeds the specified limit (22 volts), then the OVP circuit turns
off the IC and activates a latch. In order to restart the IC, the applied DC must be
removed and reapplied.
Pin 5, GND.
JVC Television Power Supply Training Page 3
ENG-02042601-T 4/14
Circuit Description.
1. The AC is inputted to the TV through line filters to prevent any line interference
such as spurious spikes from getting into the television. In addition, it blocks high
frequency interference from the television going back to the power line.
2. The inputted AC is rectified using a bridge rectifier and filtered using a capacitor.
This DC is known as the raw DC and it measures about 160V with respect to the
live ground. This DC is supplied to the switching transistor through a
transformer s primary winding.
3. In order for the IC to start
AC In
functioning and to turn on the
FET, it needs a power supply.
A start up DC voltage is
generated from the inputted AC
line through a resistor and a
diode. Diode is not used in
some chassis. The reason is
that current flows only in one
5
OVP
GND
direction because of the bridge
TSD
4
rectifier.
VCC
OSC
4. This voltage, then charges a
S
DRV
capacitor and when the DC
3
voltage reaches the IC s start
D
up voltage, the IC starts
2
STR-
functioning.
1
F6514/5
Ocp/
FB
5. When the IC starts functioning,
its internal FET is turned on
and a current flows through the
primary of the switching
transformer, the FET, and the
FET s source resistor. Since the FET conducts through an inductor (the
transformer s primary), the current ramps up from zero charging the transformer.
This generates a ramp voltage across the source resistors. This ramp voltage is fed
back to the IC s OCP/FB input (pin 1) through a feedback resistor. When this
ramp reaches 0.75V, the internal FET is turned off. From the time the FET started
conduction until it is turned off is the FET s on period
6. After the FET goes off, the energy stored in the transformer is discharged to the
transformer s other windings. In other words, when the FET is ON, the
transformer charges from the raw DC and when the FET is OFF, it discharges in
to its secondary windings
JVC Television Power Supply Training Page 4
ENG-02042601-T 5/14
7. When the IC starts functioning, the IC s power consumption increases. The
current through the start up resistor is not sufficient to maintain the IC s
conduction. The DC at IC s VCC will drop and cause the IC to shut down. To
avoid this, when the transformer discharges into its secondary windings (FET
goes off), one of the secondary voltages is used to provide additional VCC to the
IC. This is known as RUN-DC, and is necessary for the IC s uninterrupted
operation. This DC is obtained via a resistor and a diode. Every time the IC s
output transistor turns off, the transformer discharges its energy through its
windings and charges up the startup capacitor and maintains the IC s Vcc.
AC In
regulated dc
1STB13
5
OVP
GND
5V
TSD
4
VCC
OSC
S
DRV
3
CPU
D
1STB13
2
STR-
1
F6514/5
Ocp/
FB
8. The secondary voltages are now rectified by the diodes to obtain the STBY 12V.
The standby 12V, through a 5V regulator, powers up the CPU. The CPU outputs
power control signal and controls the power on/off.
9. In stand by mode, the TV s consumption is minimum and the FET s on time
could be reduced. In order to reduce the FET s on time, an additional DC is added
to the ramp voltage. This is achieved using a photo coupler. In the standby mode,
the photo coupler s LED is turned on. When the LED is on; the photo coupler
conducts and additional DC is applied to the regulator IC s pin1.
JVC Television Power Supply Training Page 5
ENG-02042601-T 6/14
10. When FET s on time is reduced, the transformer s secondary voltage reduces. In
some cases, this reduced secondary voltage affects the run DC and is not
sufficient to maintain the IC s conduction. In these cases, an additional regulated
run dc from a higher voltage winding is supplied to the IC s Vcc
11. The off time of the IC is fixed internally and is approximately 45 microseconds.
This means the IC will turn the FET on again after about 45 microseconds. When
the FET is on, its source voltage increases. This source voltage is fed back to the
OCP/FB input and will cause the IC to turn it off. The switching occurs when this
process repeats.
12. When the television s power is turned on, the televisions video-circuits,
deflection, audio circuits, and any other circuits are turned on. This increases the
power demand. More power can be transferred to the secondary by the following
methods
" Increasing the on time (the transformer s charging time)
" Reducing the off time (the transformer s discharging time)
13. Removing the voltage feedback from the photo coupler can increase the FET s on
time. When the television is turned on, the photo coupler s LED control transistor
is turned off (refer to the diagram above). This increases the FET s on time and it
depends on the source s ramp voltage.
14. In order to reduce the off time, the FET has to be turned on earlier than 45
microseconds (its natural off time). This is done using the inhibit voltage, the
transformer s AC (switched DC) output is applied to IC s pin1. When this voltage
is added to the feedback voltage, the feedback voltage rises above 1.4V and
collapses. This restarts the FET s drive. The inhibit controller has a zener diode so
that when the television is off, the voltage developed at the secondary winding is
below its threshold and it will not refresh.
15. In addition to the above mentioned controls, when the television s power is turned
on, an error amplifier IC monitors B1 voltage. If it exceeds the specified voltage,
the error amplifier activates the photo coupler to reduce the FET s on-time (see
standby mode for details). Reducing the FET s on-time will reduce the B1
voltage. The error amplifier IC includes one transistor (open collector), one zener
diode, and three resistors. The zener diode is at the transistor s emitter and it
provides the reference voltage. When the input increases above the specified
voltage, the transistor s base voltage increase and turns on the transistor. The
transistor (inside the error amplifier IC) will then turn on the photo coupler
momentarily to control the FET s on time.
JVC Television Power Supply Training Page 6
ENG-02042601-T 7/14
Relay
B1
AC In
REG 1STB13
5
OVP
GND
5V
TSD
4
VCC
OSC
S
DRV
3
CPU
D
1STB13
2
STR-
1
F6514/5
Ocp/
FB
In some chassis the horizontal output transformer generates some power supplies.
JVC Television Power Supply Training Page 7
ENG-02042601-T 8/14
JVC Television Power Supply Training Page 8
5
4
1
VCC
GND
Ocp/FB
TSD
OVP
DRV
OSC
STR-F6514/5
S
D
3
2
ENG-02042601-T 9/14
Trouble shooting
Before applying any power to the television, it is recommended to check the circuit and
ensure that there are no shorted components. If you are using an analog multimeter,
ensure that the negative side of the internal battery (in some cases, the Red probe) is
connected to the ground. A few recommended measuring points are 1STB13V,
CPU s VDD, CPU s power on/off control pin, Audio VCC, 2STB13V, B1 (135V),
etc.
Since the power supply s control circuit includes feed back circuit, it is very important
that all the control circuit must be functional for safe operation. There are critical
components; if defective, that can cause extensive damage to the power supply. A
systematic trouble shooting procedure is described below.
Equipments needed:
" Variable DC-power-supply
" Voltmeter
" Audio generator (100 KHz 1V p-p signal)
" Oscilloscope
Do not connect the TV to the AC supply before confirming the
procedures listed below
1. Ensure the 5V DC-supply to the microprocessor
Without connecting the AC supply, in order to confirm the proper functioning of the
power supply circuit using the following procedures, we need to apply a 13V external
DC supply to the TV s 12V supply line. When applying a 12V, if the microprocessor
is not powered, the microprocessor could get damaged. Confirm the 5V supply,
following the procedure shown below. (Refer to the figure shown below.)
Relay
" Disconnect the TV from the AC power
B1
supply
" Carefully discharge all capacitors using a
1
suitable resistor
DC
" Adjust the variable DC power supply s
DC output to 0V
1STB13
" If the supply has a current limit control,
5V
then set it to limit at approximately 0.75A.
" Connect the external power supply s 2
Measure
negative lead to the cold ground.
4 1
" Connect the positive lead to STB13V (this CPU
1STB13
2
is also termed as STB13, 1STB13, etc).
Refer to the schematic for convenient
connection point
" Connect a voltmeter to CPU s Vcc. While
monitoring the CPU s Vcc, slowly
increase the DC voltage from 0 to 6V.
JVC Television Power Supply Training Page 9
ENG-02042601-T 10/14
" If the CPU s Vcc does not become 5V, then troubleshoot the 5V regulator circuit
first.
" Ensuring that the CPU s Vcc does not exceed above 6.0V, slowly increase the DC
supply s output to 13V. If the CPU s Vcc exceeds above 6.0V, then trouble shoot the
5V regulator
" Ensure the current is less than 0.75A
2. If necessary, disable the CPU s protection inputs
In some models; the CPU monitors the Vertical yoke failure (VNECK), power failure
(AC OFF), or shorted supplies (SHORT). When performing the following test
procedures, if emergency (flashing LED) occurs or power goes off after a few
seconds, refer to the schematic and confirm that the emergency is not due to a
defective component.
3. Check the power control circuit and other communications
After connecting the external 13V DC to the STB13V as described above, press the
Power-button and confirm the following.
" CPU s IIC bus: Using an oscilloscope, confirm the CPU s IIC bus activity. When any
function is selected, if no data or clock is found, troubleshoot the CPU or its
peripheral components.
" Power LED: visually confirm LED on/off. If not troubleshoot the related components.
" B1 relay: Measure the voltage at the B1 relay driver transistor. Confirm that the
voltage changes from 13V to 0V and the relay operates.
" SW13V (2STB13): Measure and confirm.
" Degauss relay (if present): Similar to the B1 relay confirmation confirm the degauss
relay function.
" If any of the above does not function, then trouble shoot the related components
Relay
B1
1
DC
1STB13
5V
4 1
2
Power
CPU
ON
1STB13
2
3
Measure
JVC Television Power Supply Training Page 10
ENG-02042601-T 11/14
4. Check the operation of Photo coupler
After confirming the power control circuit s operation; connect a jumper from
STB13V to the main regulator IC (STR-Fxxxx) pin 4 (Vcc). Connect another jumper
between the cold ground and the hot ground. As shown in the table below, while
measuring the Photo coupler s voltages, operate the power switch and confirm the
voltage measurements
1
Connect Relay
B1
AC In
3
External
DC
REG 1STB13
5
OVP
GND
5V
TSD
4
VCC
OSC
S
DRV
4
3
Power
on
INH CPU
D
1STB13
2
STR-
1
F6514/5
Ocp/
FB
Measure
5
2
Connect
Photo coupler s pins
Pin1 Pin2 Pin3 Pin4
Power OFF <2.0V 0.0V 2.5V 3.0V
Power ON 13.0V 13.0V 0.0V 13.0V
If the specified measurements are not obtained, then trouble shoot the related
components. Remove the jumpers between STB13V and regulator IC pin4. Also remove
the jumper between the cold ground and hot ground.
JVC Television Power Supply Training Page 11
ENG-02042601-T 12/14
5. Check the inhibit control circuit
The inhibit control circuit refreshes
the regulator s internal oscillator
depending on the transformer s
discharge rate (secondary load). If
4
V In
this circuit does not function
3
D Inh
properly, poor regulation or
1
regulator shut down might occur.
OCP/FB
OCP
In order to confirm the proper
2
S
operation of this circuit, connect
FB
I
the variable DC supply between
s
G
Soruce
5
Resistors
the inhibit controller transistor s DC
supply
Measure
emitter and the hot ground.
Connect a voltmeter between the
regulator IC pin1 and the hot
ground. While monitoring the voltage at IC pin1, slowly increase the DC supply s
voltage. The regulator IC pin1 voltage should be zero until the applied DC voltage
exceeds the zener break down voltage. Above the zener break down voltage, pin1 DC
should increase. If not troubleshoot the related components.
6. Check the Run-DC circuit
In order to maintain the IC s
AC in
Apply
functioning, additional power
DC
Measure
supply is provided using one
of the windings from the
switching transformer. If this
circuit does not function, the
power supply will turn on
4
and off periodically. Check
V In
the diode and resistor using a
3
multimeter. Apply the D
variable DC between the
1
regulator transistor s OCP/FB
collector (diode s cathode)
Regulator
2
S
IC
and the live ground. While
monitoring the regulator IC Check
pin4, slowly increase the DC G
5
voltage unto 18V DC.
Confirm that IC pin4 voltage
appears and it does not exceed the zener voltage. If the measurement is not
satisfactory, then troubleshoot the related components.
JVC Television Power Supply Training Page 12
ENG-02042601-T 13/14
7. Switching transformer measurement
On the primary side, through the transformer, the FET switches 165 volts on and off.
This means it can be considered as
165 volts peak square wave input.
Raw DC
In order to get a 135 volts DC B1
output in the secondary, the
Scope
transformer must output 135 volts
peak square wave. This means the
Gen.
turns ratio of the Primary winding
to B1 winding is 165:135.
Similarly the other windings turns
ratio can be calculated from the
DC output.
Reg.
In order to confirm there is no shorting
in the transformer windings, when the
television is un plugged, apply 1.65
volts p-p 100 Khz sine wave across the transformer s primary winding. The B1 secondary
output should be 1.35 volts p-p. Measure other winding s output and confirm the readings
according to the specified DC voltage.
JVC Television Power Supply Training Page 13
ENG-02042601-T 14/14
Television Power supply troubleshooting difficulties
In our Television power supplies, the reference for all control circuits is the STB13V. In
order for the circuits to operate properly, we need a stable DC at this output. If there is
any instability for this STB13V, this unstable DC is passed on to the regulator IC s pin 1
through the photo coupler. If pin1 goes above the shutdown voltage, the IC might shut
down and latch.
In the flow charts and previous procedures, we used an external DC supply to test the
control circuits. After confirming the operation of the control circuits, we have to make
sure that when the TV operates, we obtain a stable STB13V. Since it does not give us
enough time to measure this supply before a shutdown occurs, please use the following
procedure.
Except D922 that outputs the STB13V, disconnect all secondary diodes
Ensuring that the startup voltage side of the bridge rectifier is positive, connect an
external DC supply (30V) to the AC terminal through a current limiting resistor (see
diagram below). The current limiting resistor prevents the IC from shutting down.
Measure STB13V (D922 Cathode) and confirm that there is no AC ripple. If you notice
AC ripples, replace the filter capacitor after D922
20 ~ 30 ohm
Relay
30V
10W
Measure
REG 1STB13
OVP 5
GND
5V
TSD
4
VCC
OSC
S
DRV
3
CPU
1STB13
D
2
STR-
1
F6514/5
Ocp/ To
FB Deguass
JVC Television Power Supply Training Page 14
Wyszukiwarka
Podobne podstrony:
JVC Power Supply trouble shooting procedure04a?5 Power Supply and Bus Systems03a?6 Power Supply and Bus Systems72 TROUBLE SHOOTING BASIC PROCEDURESATX Power supply schematics(Ebook) Radio & Electronics Course 81 Power Supply 12 Volt 3 Amp(ebook free energy) 50000 vdc power supplyFuente SMPS (Switching Mode Power Supply) 110 220VAC Foros de ElectrónicaAlarm Power SupplyIr2111 High Voltage High Speed Power Mosfet And Igbt DriverTrouble Shooting Guide id 22819 NieznanyTPA800 trouble shooting guide ATM000 008 0Power Converters And Control Renewable Energy SystemsZ1010 Trouble Shooting Guidewięcej podobnych podstron