Model 5series BMW (E60 E61)
Use the board M35080 and clip smd8
Adjustment is done in 3 steps:
1. eeprom in instrument
2. CAS programming with BMW CAS connector
3. ErrorScan
·ð Remove the instrument and open it
·ð Look for the 8-pin chip M35080
·ð ( remove this chip)
·ð connect the clip with port M35080.
·ð Connect the clip to the chip M35080 (red to pin 1).
·ð Select in theTacho Universal BMW Ä…ð BMW Ä…ð 5er/7er/X5 Ä…ð E6X/E65/E66 Ä…ð
M35080 clip
·ð The Tacho Universal showns you the original km.
·ð Save the data!!!
·ð Go back to the menue BMW Ä…ð 5er/7er/X5 Ä…ð E6X/E65/E66 Ä…ð 35080-0 (erase)
and wait until Tacho Universal displays OK
·ð Select BMW Ä…ð 5er/7er/X5 Ä…ð E6X/E65/E66 Ä…ð M35080 clip
·ð Load the original data you saved before and write it completely to the chip
·ð Error message data not equal can be ignored
·ð Select BMW Ä…ð 5er/7er/X5 Ä…ð E6X/E65/E66 Ä…ð M35080 clip and program the new
km.
·ð Do not install the instrument back yet! Before that, the CAS must be programmed
to 0
·ð Please follow the instructions carefully!!!
If the chip is 35080 V6 you must replace it by a new. This is new not
erasable generation.
Modell 5series BMW E60 / E61
2. Schritt Cas Diagnose über BMW Cas Stecker
Connect the cluster connector from car to port A. (Pin1 to red)
Attention:
Before you pull a fuse,
remove the key and store it away from the car!
While programming, do not open or close any doors or touch any buttons!!!
·ð Remove the small fuse. The fusebox is on the passengers side behind the
glovebox. See picture.
Important: the small fuse stays removed during the complete process.
·ð Connect the Can Dongle with the BMW CAS cable and the cluster connector
in the car.
·ð Select BMW Ä…ð 5er/7er/X5 Ä…ð E6X/E65/E66 Cas Prog
·ð Follow exactly the instructions in Diga-Display, like light on/off
·ð When it asks to remove fuse , the big fuse must be removed
·ð i fit asks you to put it back, put back the big fuse
·ð after programming is finished, put back the small fuse
5series BMW (E60 E61)
.
Attention:
Before you pull a fuse,
remove the key and store it away from the car!
While programming, do not open or close any doors or touch any buttons!!!
Remove the small fuse. It stays removed If you are asked to remove or put back
during the complete process. fuese during programming, it is THIS fuse
3. ERRORSCAN
Connect the connector shown to the OBD2
connector and select the menue Errorscan .
Wait until the main menues returns.
This can take about 5 minutes!
Wyszukiwarka
Podobne podstrony:
OBD BMW E60bmw 5 E60 palniki ksenonoweBMW E60, 61 AC Schnitzer chipyBMW E60 halas z klimatyzacjie60 bmw części i akcesoria instrukcje instalacjiBMW e60 e61 wymiana termostatu foto relacjaSwiatla z kluczyka bmw e60(2)Swiatla z kluczyka bmw e60Światła do jazdy dziennej BMW e60BMW E39 Wymiana wężyków spryskiwaczybmw E46 halas sprezarkiBMWBMW 735i 1992http www e32 schrauber de bmw daten getriebe ZF huile pour boite autowięcej podobnych podstron