suzuki rm25053
FRONT FORK AND STEERING 15-7
FRONT FORK AND STEERING 15-7
he center bolt.
mbly and fork spring and spring
SPRING CHANGE
• Remove the front forks. (d7“ 15-11)
• Thoroughly clean the fork before disassembly.
CAUTION
The fork oil quantity must be adjusted equally on both fork legs to provide equal performance.
Scratches or other damage the on inner tubę or on the oil seal lip will cause oil leak.
Avoid scratching or damaging the inner tubę or the oil seal. Use a mild detergent or car wash soap and sponge out dirt with plenty of water.
• Remove the fork cap bolt and drain fork oil. (d7“ 15-12)
• Loosen the center bolt completely. (CCyMS-IS)
• Compress the outer tubę by hands and install the conrod holder (special tool) between the axle holder bottom (D and locknut. (£7*15-13)
ItoSlI 09910-20115: Conrod holder
Hołd the locknut with^a-wrenc (£7*15-13)
Remove the push roi Remove the damper n coller. (£7*15-14)
Hołd the front fork inverted position for morę than 20 minutes the allow the fork oil to fully drain. (£7*15-5)
Force out the remaining oil using compressed air completely. (£7*15-5)
• Replace the spring.
|
SPRING/No. |
SPRING RATĘ |
Identification (Slit mark on the spring end) |
|
STD 51171-37FC0 |
4.4 N/mm (0.44 kgf/mm) |
III |
|
SOFT 51171-37FD0 |
4.2 N/mm (0.42 kgf/mm) |
I |
|
HARD 51171-37FE0 |
4.6 N/mm (0.46 kgf/mm) |
II |
• Install the damper rod assembly. (£7* 16-21)
Wyszukiwarka
Podobne podstrony:
64911 Suzuki RM2503 FRONT FORK AND STEERING 15-27 ♦ Fit the upper and lower outer races with the sp
41125 Suzuki RM2507 FRONT FORK AND STEERING 15-11FRONT FORKREMOVAL • Place a błoc
44243 Suzuki RM2501 FRONT FORK AND STEERING 15-25STEERINGREMOVAL • Remove the fro
suzuki rm25047 FRONT FORK AND STEERING 15-1FRONT FORK AND STEERING -CONTENTS- CONSTRUCTION
suzuki rm25049 FRONT FORK AND STEERING 15-3FRONT FORKTUNING The front fork compression and rebound
suzuki rm25051 FRONT FORK AND STEERING 15-5OIL CHANGE (Only for outer tubę oil cham-ber) • &n
suzuki rm25055 FRONT FORK AND STEERING 15-9FRONT FORK TUNING PROCEDURĘ Test ride the motorcycle and
suzuki rm25057 FRONT FORK AND STEERING 15-11FRONT FORKREMOVAL • Place a błock und
suzuki rm25059 FRONT FORK AND STEERING 15-13 • Clamp the axle holder (D with a vi
suzuki rm25061 FRONT FORK AND STEERING 15-15INNERTUBE • Separate the inner tubę out of the outer tu
suzuki rm25063 FRONT FORK AND STEERING 15-17 INNER TUBĘ AND OUTER TUBĘ • Inspect
suzuki rm25065 FRONT FORK AND STEERING 15-19 • Install the new oil seal (D with t
suzuki rm25069 FRONT FORK AND STEERING 15-23 • Tighten the center bolt to the specified torque. H C
suzuki rm25071 FRONT FORK AND STEERING 15-25STEERINGREMOVAL • Remove the front wh
suzuki rm25073 FRONT FORK AND STEERING 15-27 FRONT FORK AND STEERING 15-27 • Fit the upper and lo
56010 Suzuki RM2507 FRONT FORK AND STEERING 15-1FRONT FORK AND STEERINGCONTENTS CONSTRUCTION
60169 Suzuki RM2509 FRONT FORK AND STEERING 15-13 ♦ Clamp the axle holder @ with
26502 Suzuki RM2507 FRONT FORK AND STEERING 15-21 FRONT FORK AND STEERING 15-21 Approx.10 mm (0.39
więcej podobnych podstron