p44 (14)

possibly crack it. Notę that ring seats firmly in its groove; if it doesn't, discard it and install another new one. A lock ring loosely installed will rapidly loosen further in service. and finally will come off pin, resulting in both piston and cylinder soon being damaged beyond repair. Never re-install a used lock nng; always use a new one.

Standard size pistons and those in the lower over-size steps have two horizontal slots, one front and one rear, in bottom ring groove. Oversize pistons in the larger steps are slotted horizontally and also have a vertical slot in one thrust face. Pistons with only the horizontal slots may be fitted with either thrust face to the front. Pistons with vertical slot in one thrust face must be fitted with that thrust face to the front.

Pistons obtained from the manufacturer, standard oj oversize, are fitted with pin correctly fitted and piston rings installed. Piston pin lock rings are also supplied, one assembled on pin, the other one loose. Check ring gaps in cylinder being refitted.

Piston Rings

Piston rings are of two types; the two upper rings on each piston are plain compression rings. The bottom ring on each piston is an oil control ring, having a channel in its face.

Piston rings must have proper side clearance in ring grooves. In new assembly, this is .004". Check with thickness gauge. Maximum permissible side clearance is .008".

Gap between ends of rings, when inserted sąuarely in cylinder borę, must be .010" to .020". If gap is less than .010", ring ends may butt under expansion and rings may be scored or broken. Gap may be increased by filing with a fine-cut file.

Installing and Fitting Connecting Rod Upper Bushing

Connecting rod upper end bronze bushing may need to be renewed either due to wear and exces-sive pin clearance or due to becoming loose in rod.

Inspect for both conditions.

When bushing is found tight in rod but is worn to excessive pin clearance (.002" or morę) it is, of course, possible to service it by reaming oversize and fitting an oversize pin. However, it is better prac-tice to install a new bushing and ream it to fit a standard pin, except when piston to be used has previously been fitted with oversize pin or pin is loose in bosses, necessitating fitting with larger pin. The principal objection to fitting upper end oversize is that, in the event of emergency field service reąuir-ing quick fitting of pistons, considerably morę time is reąuired for the job if upper end bearing is over-size. New pistons obtained from the manufacturer are supplied correctly fitted with standard pin, and installing one is a short job if the rod bushing is already reamed to standard size. If bushing has been reamed oversize, either new bushing must be installed and reamed to standard size or piston must be reamed oversize to fit an oversize pin, which involves extra time.

When installing new upper end bushings in rods disassembled from engine, an arbor press, if avail-able, is usually used to press out old bushings and press in the new.

When renewing bushings in connection with only a top overhaul, use special manufacturer's tools shown in Illustration 33. Bushing tool is number 12Q57-X; rod holding fixture is number 12058-X. Be careful to start new bushings with oil slot in align-ment with oil slot in rod.

Ream new bushing to size, or, preferably, ream nearly to size and finish to exact size with a hone (reamer number 11915-X; hone number 11844-X). A properly fitted pin should have .001" clearance; with this clearance, pin will have just noticeable shake in bushing. Fitting tighter is likely to result in a seized pin or bushing loosened in rod.

Oversize piston pins are available in the following oversizes: .002", .004", .006", .008", .010" and .012".

After installing new connecting rod upper end bushings in connection with only a top overhaul, connecting rod alignment must be checked the same as when an engine is completely overhauled. See "Aligning Rods," Page 41.

44

Wyszukiwarka

Podobne podstrony:
select sum(val) from numbers; Notę that any alphabetic values in the result set are turned into 0 by
4 trees that were cut off in 2015 Ecosystem Services [25] CD: animal habitat and its nutritional bas
It is inicresting to notę that because of improvcd persona! and cnvironmcntal hygicnc standnrds
ISBN: 978-989-95618-4-7 Regarding possible eamings. it is possible to obsener that the stakes are mu
step After assembling the buttsiock, assemble the młd part and glue as shown. Notę that I left it h
cells 4 days after tumor implantation. It is of importance to notę that in vivo depletion with anti-
00057 ?3894d9003361260a26a45e7f0f6dd0 56 Hembree & Zirnmer where Gt = P; H’(R< + H P; H’) 1
Stirleff Now ffom the Fii^st Law for a cycle: lth Notę that: ln Ul! = -ln fv4) Ul, U3J thus we
Paradiddle Power 6 Part 5: Jazz Fills With Triple Paradiddles In Triplets Here again, notę that only
fizyka laborki2 14 IhWm/i.ck /iT^/niA 0c€fO-
v -AO
Pioneer has transformed the cassette deck into a component that gives you a new dimension of con-tro

więcej podobnych podstron