File0007 (2)
Figurę 10. Wiring of pass transistor PCB.
Setting Up
The following procedures should be carried out very carefully and not rushed. The performance of the pro-ject is dependant on the accuracy of these adjustments.
Power Supply Alignment
With the unit disconnected, turn the front panel current limiting control
fully clockwise, and the two voltage Controls (fine and coarse) to their mid-way positions. The two presets on the inain panel need to be adjusted again; RV1 (maximum current adjustment) needs to be turned fully anticlockwise, while RV2 (minimum current adjustment) needs to be turned fully clockwise. Alignment can now proceed; for this you will need an ammeter (i.e. multimeter set to measure current)
with a rangę of at least 10A. This should be connected across the power supply’s output terminals. After pow-ering up, the ‘current limit’ LED will light up (the Iow resistance of the ammeter presents a virtual ‘dead short’ to the PSU). RV1 should now be adjusted until the meter reads 10A. Disconnect the meter, and turn the voltage/current limit adjustment Controls fully anticlockwise. RV2 should now be adjusted until the current limit LED lights up dimly.
Calibration of Digital Displays
After connecting a multimeter (set to 30V rangę or higher) to the unit’s output terminals, set the current limit control to 1A. Switch on (both displays should read 000) and adjust the voltage Controls so that the meter gives a reading of 30V. Adjust the (voltage) ‘meter adjust’ preset (RV1 on the display PCB, accessible from the front panel) until it reads the same as the multimeter. Turn the unit off, and set the multimeter to its 10A (at least) current rangę. After switching the unit back on again, the current limit control should be set so that the multimeter reads 8A. Adjust the (current) ‘meter adjust’ preset, RV2 on the display panel, until the unit’s display reads the same as the multimeter. Access to RV2 can also be gained from the front panel.
Your power supply is now ready for use!
46
Maplin Magazine October 1992
Wyszukiwarka
Podobne podstrony:
23ddg13 llVisual Basic 4.0 SetupWizard - Ślep 7 of 7EJ The following files should be distribuled wi
27ddg10 llVisual Basic 4.0 SetupWizard - Ślep 7 of 7ES The following files should be distribuled wi
00230 819cd9235a78d0f202ffb72a6ad790 232 Baxley Figurę 10. Fit of IMA Model to Machinę Average Y2
Figurę 10.4 Strueture of the retina. (A) Section of the retina showing overall arrangement of r
10 1 Fascia lata Medial collateral ligament Patellar ligament Extensor retinacula Figurę 10-1 Anatom
7 10 11 th rib 12th rib Figurę 7-10 Anatomy of external obligue Rectus sheath (removed over
10 7 Figurę 10-7 Anatomy of the plantar fascia
10 M.J.M. Tielen of GM plants and EU approvals, the EU has so far been unable to come forward with a
00027 ?6ad09812700ed54e35de4f20e2a7ad 26 Molnau The SPR procedurę can be applied to the fuli rangę
koliber z motylem i (3) V V • •••Symbol List The pair of colors whose names are listed below in r
5) in Artide 10, the following paragraph shall be added: ‘6. Paragraphs 1 to 4 sha
2) in Article 57(1), the following point shall be added: (t) taking decisions as referred to in Art
MR293R19021 1 The wing pan*l musu be renoved beforc. this operćit.ion can be carried out. COMPOSITI
MR293R19041 1 This operation is to be carried out on tha body jig bench. See sub-section 40 of
First research works on LCA at Poznań University of Technology 99 From above conclusions, the follow
więcej podobnych podstron