{Change Comments ***********************************************************}
{6/14/95, Updated for Catalyst v2.20 per Fanuc 10T MS [-] L001.85 Format, DWB}
{7/18/95, Added IF NOT LastFeat? at CkCRC sub, DWB}
{
Format: Fanuc 18T [-¨] L394.85.02
11/21/95
For: Tamshell
Arcs now output R's instead of IJK
Changed prog label ID from O to :
TH}
{12/11/95
Modified: Fanuc 18T [-¨] L394.85.02
For: Tamshell
Versions: ncCad 4.33.01/ncCAM 4.33.01/ncPost 4.33.08/Catalyst v2.28.08/Compost 4.21.34/1.0a
Changes made per Ron Knesal of Tamshell.
Deleted OpToolID LatheOffset at AppMove sub.
Deleted LOfstOff '00' at CheckOffset sub.
Deleted all support of ConstantSurfaceFeed at CheckOffset sub, FirstOperation, NewTool, common point
and end of Prog.
Deleted Preset Home MaxRPM at FirstOperation and NewTool.
Added Rapid CRCOff CSSOff 'G97' OpToolID LatheOffset Speed SpinOn block at FirstOperation and
NewTool.
Changed NewHome LOfstOff '00' to 'G28U0W0' at NewTool.
Changed FirstHome OpToolID '00' SpinOff to 'G28U0W0' at end of Prog.
DWB}
{7/8/96,
Created: Lxxx.85
changed to postive X values, MPK}
{1/22/98
Initial: Fanuc 18T [WP] LXXX.85
Created: Fanuc 18T [WP] LXXX.85
For: Westwood Prec.
Comments: Forced Sequence number at beginning of FirstOp and NewTool ops,
added: SeqLabC 'G54' Rapid 'X0Z0T0' EOL at FirstOp, twice in NewTool, and to program end,
changed start block in FirstOp and NewTool to:
SeqLabC CSSOff 'G97'
IF ConstantSurfaceFeed?
CalcRPM1
ELSE
Speed
END
OpToolID LatheOffset SpinOn EOL
Deleted G28 block in NewTool and end of program,
Changed program label to 'O',
Deleted Untool block from program end,
added G97 block to end of program,
added ProgStop to end of program,
moved CoolOff at end of program to same line as OpExitZCPC,
removed canned cycle info for peck cycles from form,
MPK
}
{18May98
Original: Fanuc 18T [WP] L698.85
Created: Fanuc 18T [WP] L698.85.1
For: Westwood Precision
Changes made per: David Pickett
Deleted old version numbers and comments e.g. {.62}, {commands}, {literals}, etc
Added IF NOT SameTool? Boolean to OpComments
Added CSS Boolean to output G96 in ApproachSP
Deleted ReverseXZArcs at the Start of executable Prog
Changed ProgID1 to 'O' Program# at the start of FirstOperation
Deleted leading and trailing spaces in all Comments
Deleted SeqLab from FirstOperation and NewTool and moved to the Tool Comment Line
Added Preset MaxRPM in FirstOperation and NewTool at Start of new Operation
Added G97 Boolean at NewTool Finish off last Operation
Changed Thread Feed Address from 'E' to 'F' in MachSpec
Charles Winston}
{12/2/98
Initial: Fanuc 18T [WP] L698.85.1
Created: Fanuc 18T [CST] Lxxx.85
ForUser: Carolina Specialty Tools, Inc.
Control: ????
Machine: ????
Develop: ComPost2 v1.7b11, Virtual v5.02
Comment: New processor per marked up readout from Mark Troutman
Modified G54 line at beginning of tools
Changed:
'G54' Rapid 'X0Z0T0'
To:
WFO1 OpToolID '00'
Modified G54 line at end of tools
Changed:
'G54' Rapid 'X0Z0T0'
To:
'G28U0'
'G28W0'
Modifed CSS to start operation in G96, not G97, and do not go to G97 at end of operation.
Added CoolOff between tools.
Cleaned up and updated per Fanuc 10T MS [-] L001.85.01.02
Jim Radcliffe}
{01/07/99,
Initial: Fanuc 21T MS [CST] L799.85
Created: Fanuc 21T MS [CST] L799.85
For: Carolina Specialty Tools
Changes to Prog:
1) ProgStart - changed literal 'O' to literal ':' in front of Program#.
CDH}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.####;0.'
#3 = '#######0'
#4 = '###^##0'
#5 = '#.######;0.'
#6 = '###0'
#7 = '#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(MUL#,2) { Non-Canned Threading AutoFinish }
FORMAT(InFeedAngle#,2)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Program#,3)
FORMAT(Operation#,3)
FORMAT(Tool#,3)
FORMAT(Dwell#,4)
FORMAT(FeedIPR#,5)
FORMAT(CalcEPRPM#,6)
FORMAT(RapidF#,7)
{Prog Subroutines **********************************************************}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'(OPERATION ' Operation# ': ' OperationType$ ')' EOL
END
IF OperationComment?
'(' OperationComment$ ')' EOL
END
IF WorkGroupComment?
'(' WorkGroupComment$ ')' EOL
END
IF ToolTypeComment?
'(TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ')' EOL
END
IF ToolComment?
'(' ToolComment$ ')' EOL
END
RestoreScale
END
RETURN
PSInit: {reset flags from last Op, .70}
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL
PSStuff
NextPS
RETURN
StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN
FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN
FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN
ApproachSP:
IF ApproachFace?
SeqLabC StockOnNoCan XSPC EOL
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqLabC FeedNoCan ZSPC FeedRateNoCan EOL
END
ELSE { ODApproach/IDApproach }
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
END
RETURN
AppMove:
StockOff ThisOpEntryZCP CoolOn
RETURN
Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqLabC ThisOpEntryXCP AppMove EOL
ELSE
IF ApproachID?
SeqLabC XOpCD AppMove EOL
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP AppMove EOL
END
END
ApproachSP
RETURN
CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
DoOpComments
DoPostScript
IF NewToolOffset?
SeqLabC LOfstOff '00' EOL
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
ELSE
SeqLabC Preset MaxRPM EOL
END
END
SeqLabC
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? SpeedRPM# LAST SpeedRPM#
Speed
END
ELSE
CSSOn 'G96' Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
CSSOff 'G97' Speed
ELSE
IF NotEqual? SpeedRPM# LAST SpeedRPM#
Speed
END
END
END
IF NewToolOffset?
OpToolID LatheOffset
END
IF LAST ProgStop?
SpinOn
END
EOL
SeqLabC
IF LAST ProgStop?
CoolOn
ELSE
IF NOT CoolOff? AND LAST CoolOff?
CoolOn
END
END
EOL
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC:
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
IF NOT LastFeat?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN
ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
ELSE
IF CannedCycle?
SeqLab
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC
IF LAST ThreadFeat?
Rapid
ELSE
RapidC
END
MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
END
END
END
END
END
NEXTFeat
RETURN
CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
IF LAST Threading?
Rapid
ELSE
RapidC
END
END
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
SetAbs
PosSideLathe
StandardXZArcs
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
':' Program#
IF UseComments? AND ProgramNameComment?
'(' ProgramName$ ')'
END
EOL
IF UseComments?
IF ProgramComment?
'(' ProgramComment$ ')' EOL
END
IF FormatNameComment?
'(FORMAT: ' FormatName$ ')' EOL
END
IF TimeComment?
'(' Date$ ' AT ' Time$ ')' EOL
END
IF MovesComment?
'(OUTPUT IN ABSOLUTE INCHES)' EOL
END
END
RestoreScale
OpenSub
StockOff
SetHome
Plane
DoOpComments
DoPostScript
SeqLab WFO1 OpToolID '00' EOL
SeqLabC Preset MaxRPM EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96' Speed
ELSE
CSSOff 'G97' Speed
END
OpToolID LatheOffset SpinOn EOL
Approach
ELSE
IF NewTool?
{Finish off last Operation}
StockOff
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC CoolOff EOL
DoEndOpPS
SeqLabC 'G28U0' EOL
SeqLabC 'G28W0' EOL
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END
{Start new Operation}
' ' EOL
DoOpComments
DoPostScript
SeqLab WFO1 OpToolID '00' EOL
SeqLabC Preset MaxRPM EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96' Speed
ELSE
CSSOff 'G97' Speed
END
OpToolID LatheOffset SpinOn EOL
Approach
ELSE
IF SameTool?
{Start new Operation}
StockOff
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
END
END
CheckOffset
ApproachSP
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
SeqLabC LCycle
IF ApproachFace?
'Z' FirstMoveEPZ# XatFinZ
ELSE
XatFinZ FinZ
END
XTapAtZ FeedRate EOL
SimpleRough
ELSE
TagInc
SetPass2
IF RoughContour?
SeqLabC LCycle 'Pł' Tag# 'Q˛' Tag# XStkLeft ZStkLeft CutDepth FeedRate EOL
'>' Tag# EOL
SeqLab StepMove StrtPos EOL
ELSE
IF RoughPatternShift?
SeqLabC LCycle 'Pł' Tag# 'Q˛' Tag# XStkLeft ZStkLeft XminusU ZminusW NumCuts FeedRate EOL
'>' Tag# EOL
SeqLab Rapid StrtPos EOL
END
END
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'Pł' Tag# 'Q˛' Tag# EOL
END
SetPass1
TrackXNO# CycleStartX#
TrackZNO# CycleStartZ#
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
SeqLabC LCycle XatFinZ FinZ XTapAtZ CutMethod ThrdHeight CutDepth ThrdLead 'A' InFeedAngle# EOL
IF AutoFinish?
SeqLabC 'G92' XatFinZ FinZ XTapAtZ ThrdLead EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF PeckChipBreaker?
SeqLabC LCycle ZDepth RLevel Dwell Peck Retract FeedRate EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
ELSE
IF Grooving?
StockOn
SetPass1
SeqLabC StrtPos EOL
ToolPath
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish? { .82.1c }
StockOff
IF Turning?
IF ApproachFace?
SeqLabC RapidC ZOpECPC EOL
ELSE
SeqLabC RapidC XOpECDC EOL
END
ApproachSP
SeqLabC StockOff StrtPosC EOL
ToolPath
ELSE
IF Roughing? AND NOT RoughSimple?
SetPass2
SeqLabC RapidC XSPC ZSPC EOL
SeqLabC StockOff StrtPosC EOL
ToolPath
SetPass1
ELSE
IF Threading?
SeqLabC 'X' MUL# Num#('2') ADD# FinishXRadius# Taper# EOL
SeqLabC 'G32'
IF Taper?
XatFinZ
END
FinZ ThrdLead EOL
SeqLabC Rapid XSP EOL
SeqLabC ZSP EOL
END
END
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}
{End of program ************************************************************}
{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
IF Threading?
Rapid
ELSE
RapidC
END
END
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC CoolOff EOL
DoEndOpPS
SeqLabC 'G28U0' EOL
SeqLabC 'G28W0' EOL
IF ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'(FILE LENGTH: ' FileBytes# ' CHARACTERS)' EOL
END
IF FileFeetComment?
'(FILE LENGTH: ' FileFeet# ' FEET)' EOL
END
IF FileMetersComment?
'(FILE LENGTH: ' FileMeters# ' METERS)' EOL
END
Close
END
Wyszukiwarka
Podobne podstrony:
Fanuc 21T MS [WIKA] L837 85Fanuc 21T MS [VE] L718 85Fanuc 21T MS [ EMT] L642 85Fanuc 21T MS [WCS] L558 85 1Fanuc 6T MS [SE] L683 85Fanuc 10T MS [PT] L703 85 1Fanuc 18M MS [CST] NCT81 16Fanuc 16T MS [AM] L615 85 2Fanuc 15T MS ( CDS) L418 85 1Fanuc 6T MS [VE] L392 85 1Fanuc 10TEF MS SL 4 L281 85Fanuc 10T MS [BMR] L768 85Fanuc 21TB MS [YMS] L770 85Fanuc 10T MS [ TPM] L455 85Fanuc 16T MS [ IN] L443 85Fanuc 10T MS [ CES] L107 85więcej podobnych podstron