Glow Worm installation and service manual Ultimate 50BF UIS


221790B.11.00
Instructions for Use
Installation and Servicing
To be l ef t wi t h t he user
50BF
G.C. No. 41 319 53
Balanced Flue Boiler
BS 6332
BS 5258
This is a Cat I2H Appliance
Reference in these instructions to British Standards and Statutory
Regulations/Requirements apply only to the United Kingdom.
The instructions consist of three parts, User, Installation and Servicing Instructions, which includes the Guarantee Registration
Card. The instructions are an integral part of the appliance and must, to comply with the current issue of the Gas Safety
(Installation and Use) Regulations, be handed to the user on completion of the installation.
Guarantee Registration
Thank you for installing a new Glow-worm appliance in your home.
Glow-worm appliances' are manufactured to the very highest standard so we are pleased
to offer our customers' a Comprehensive First Year Guarantee.
Attached to the centre of these instructions is your Guarantee Registration Card, which we recommend you
complete and return as soon as possible.
If this card is missing you can obtain a copy or record your registration by telephoning the Heatcall Customer
Service number 01773 828100.
Our Guarantee gives you peace of mind plus valuable protection against breakdown by covering the cost of:
' REGISTER YOUR GLOW-WORM APPLIANCE
All replacement parts
O'
FOR 1ST YEAR GUARANTEE PROTECTION
'
All labour charges
O'
' All call-out charges
O'
CALL 0208 247 9857
Hepworth Heating Ltd.,
Customer Services:
Nottingham Road, Belper, Derbyshire. DE56 1JT
Tel: (01773) 828100
General/Sales enquiries:
Tel: (01773) 824141 Fax: (01773) 820569
One Contact Local Service Fax: (01773) 828070
3790
Important Information
Testing and Certification
This boiler is tested and certificated for safety and performance. It is therefore important that no alteration is made to the boiler, without
permission, in writing, from Hepworth Heating Ltd.
Any alteration not approved by Hepworth Heating Ltd., could invalidate the certification, boiler warranty and may also infringe the
current issue of the Statutory Requirements, see Section 1.4.
CE Mark
This boiler meets the requirements of Statutory Instrument No. 3083 The boiler (Efficiency) Regulations, and therefore is deemed
to meet the requirements of Directive 92/42/EEC on the efficiency requirements for new hot water boilers fired with liquid or gaseous
fuels.
Type test for purposes of Regulation 5 certified by: Notified body 0086.
Product/productioncertifiedby: Notified body 0086.
The CE mark on this appliance shows compliance with:
1. Directive 90/396/EEC on the approximation of the laws of the Member States relating to appliances burning gaseous fuels.
2. Directive 73/23/EEC on the harmonization of the Laws of the Member States relating to the electrical equipment designed
for use within certain voltage limits.
3. Directive 89/336/EEC on the approximation of the Laws of the Member States relating to electromagnetic compatibility.
INFORMATION FOR THE INSTALLER AND SERVICE ENGINEER.
Under Section 6 of The Health and Safety at Work Act 1974, we are required to provide information on substances hazardous to
health.
CERAMIC FIBRE/INSULATION PADS, GLASSYARN.
These can cause irritation to skin, eyes and the respiratory tract. If you have a history of skin complaint you may be susceptible to
irritation. High dust levels are usual only if the material is broken. Normal handling should not cause discomfort, but follow normal
good hygiene and wash your hands before eating, drinking or going to the lavatory. If you do suffer irritation of the eyes or severe
irritation to the skin seek medical attention.
CONTROL THERMOSTATS
These contain very small amounts of dichlorotrifluroethane in the sealed phial and capillary. If broken, under normal circumstances
the fluid does not cause a problem, but in case of skin contact, wash with cold water. If swallowed drink plenty of water and seek
medical attention.
CONTENTS DESCRIPTION SECTION PAGE No.
Introduction 3
INSTRUCTIONS
Lighting the Boiler 4
FOR USE
General Data 1 5
INSTALLATION
Flue & Ventilation 2 7
INSTRUCTIONS Water Systems 3 9
Flue and Appliance Preparation 4 11
Boiler Installation 5 13
Commissioning 6 17
Instructions to User 7 18
Servicing 8 19
SERVICING
Fault Finding 9 21
INSTRUCTIONS
Replacement Parts 10 24
Spare Parts 11 27
221790B 2
Instructions for Use
Introduction
100mm
Please read these instructions and follow them carefully for the
safe and economical use of your boiler.
The Ultimate BF series are central heating boilers designed to
provide heating and indirect domestic hot water.
Important Notice
This boiler is for use only on G20 gas.
6mm
The Gas Safety (Installation and Use)
6mm
500mm
Regulations
In your interest and that of gas safety it is the Law that ALL gas
appliances are installed by a competent person in accordance
with the current issue of these amended regulations.
Gas Leak or Fault
If a gas leak or fault exists or is suspected, the BOILER MUST
BE TURNED OFF, including the electrical supply and MUST
65mm
Diagram 1
NOT BE USED UNTIL THE FAULT HAS BEEN PUT RIGHT.
Advice/help should be obtained from your installation/servicing
company or the local gas undertaking.
Data Label
Maintenance
The serial number and GC number of the boiler can be found on
the Data Label, see diagram 2.
To ensure the continued efficient and safe operation of the
boiler it is recommended that it is checked and serviced as
Boiler Clearances
necessary at regular intervals. The frequency of servicing will
depend upon the particular installation conditions and usage, If fixtures are positioned close to the boiler space must be left as
but in general once a year should be enough. shown in diagram 1. Enough space must also be left in front of
the boiler to allow for servicing.
If this appliance is installed in a rented property there is a duty
of care imposed on the owner of the property by the current
Boilers Installed in a Compartment or
issue of the Gas Safety (Installation and Use) Regulations,
Cupboard
Section 35.
If the boiler is installed in a compartment or cupboard do not
It is the Law that any servicing be carried out by a competent
obstruct any ventilation openings.
person.
Do not use the compartment or cupboard for storage.
To obtain service, please call your installer or Heatcall (Glow-
worm s own service organisation) using the telephone number
Boiler Electrical Supply
given on the controls tray.
WARNING. This boiler must be earthed.
Please be advised that the  Benchmark logbook should be
completed by the installation engineer on completion of
The boiler must only be connected to a 230V~50Hz supply
commissioning and servicing.
protected by a 3A fuse.
All CORGI Registered Installers carry a CORGI ID card, and
All wiring must be in accordance with the current issue of
have a registration number. Both should be recorded in your
BS7671.
boiler Logbook. You can check your installer is CORGI
Wiring to the boiler must be PVC insulated type to the current
registered by calling CORGI direct on :- 01256 372300.
issue of BS6500 Table 16, not less than 0.75mm2 (24/0.20mm).
Cleaning
The colours of 3 core flexible cable are:-
WARNING. This boiler contains metal parts (components) and Brown - live, Blue - neutral, Green and yellow - earth.
care should be taken when handling and cleaning, with particular
As the markings on your plug may not correspond with these
regard to edges.
colours, continue as follows:-
Clean the casing occasionally by wiping it over with a damp
The wire coloured blue must be connected to the terminal
soapy cloth or dry polishing duster.
marked  N or  Black .
Do not use an abrasive cleaner.
The wire coloured brown must be connected to the terminal
marked  L or  Red .
Protection Against Freezing
The wire coloured green and yellow must be connected to the
If the boiler is to be out of use for any long period of time during
terminal marked  E ,  Earth ,  Green or the earth symbol .
severe weather conditions we recommend that the whole of the
system, including the boiler, be drained off to avoid the risk of
freezing up. Make sure that, if fitted, the immersion heater in the
indirect cylinder is switched off.
3 221790B
3864
Instructions for Use
To Light The Boiler
WARNING. If the pilot flame goes out, either intentionally or by
accident, no attempt should be made to relight it for at least
three minutes.
Identify the controls by reference to the diagram 2.
Switch off the electrical supply to the boiler.
Turn the control thermostat knob  B fully anti-clockwise to the
 O , Off position.
Push in control button  D , keep pressed in and at the same time
operate the piezo button  A until the pilot lights, look through
viewing window  E . After the pilot lights keep the control button
 D pushed in for 20 seconds. If the pilot fails to stay alight a
safety device prevents immediate relighting.
Do not attempt to relight until the safety device has reset, that
is, for at least three minutes.
Switch on the electrical supply and check that all external
controls are calling for heat.
Turn the control thermostat knob  B clockwise to any position
between  MIN and  MAX and the burner will light.
The maximum setting is about 82oC (180oF).
The above sequence must be repeated every time that the
burner has to be relit.
To Turn the Boiler Off
For short periods, turn the control thermostat knob  B fully anti-
clockwise to  O Off. To relight, turn control thermostat knob
clockwise to any position between  MIN and  MAX .
For longer periods, turn the control thermostat knob  B fully
anti-clockwise to  O Off and slide multi-functional control
button  D to the left, it will automatically reset. Switch off the
electrical supply to the boiler.
To relight, follow the full lighting sequence given above.
A PIEZO UNIT BUTTON
B THERMOSTAT CONTROL KNOB
C GAS SERVICE COCK
(shown in off position)
D CONTROL BUTTON (GAS)
E
E VIEWING WINDOW
C
B
DATA LABEL
A
D
Diagram 2
221790B 4
8042
1 General Data
F
A S S
C
N N
B
D
M
C
L
L
E
R
P
SIDE ELEVATION FRONT ELEVATION
22mm COPPER PIPE
GAS CONNECTION RC1/2 (1/2 in. BSPT.)
OVERALL DIMENSIONS (given in millmetres) Diagram 1.1
MODELS
A B C D E F L M N P R S
50BF 75 297 132 398 700 360 574 35 87 131 60 146
Important Notice
Detailed recommendations are contained in the current issue of
the following British Standards and Codes of Practice:-
This boiler is for use only on G20 gas.
BS6798, BS5440 Part 1 and 2, BS5546 Part 1, BS5449, BS6891,
All dimensions are given in millimetres (except as noted).
BS6700, BS7593, BS7478, BS7671.
This boiler can be used only on an open vented system, with
Manufacturer s instructions must not be taken as overriding
either gravity or pumped domestic hot water connections to the
statutory requirements.
indirect cylinder.
Wherever possible, all materials, appliances and components
1.2 Data
used shall comply with the requirements of applicable British
See Table 1
Standards.
1.3 Range Rating
Where no British Standard exists, materials and equipment
should be fit for their purpose and of suitable quality and
This boiler is range rated and may be adjusted to suit individual
workmanship.
system requirements.
Table 2 gives the ratings and settings.
Sheet Metal Parts
The Seasonal Efficiency Domestic Boilers UK (SEDBUK)
WARNING. When installing or servicing this boiler care should
is 73%.
be taken when handling sheet metal parts, to avoid any possibility
of personal injury.
The value is used in the UK Government s Standard Assessment
Procedure (SAP) for energy rating of dwellings. The test data
1.1 Statutory Requirements
from which it has been calculated have been certified by B.S.I.
The installation of the boiler must be carried out by a competent
1.4 B.S.I. Certification
person in accordance with the relevant requirements of the
current issue of:-
This boiler is certificated to the current issue of British Standard
6332 Part 1, invoking the current issue of BS5258 Part 1 for
Manufacturer s instructions, supplied.
performance and safety. It is, therefore, important that no
The Gas Safety (Installation and Use) Regulations, The Building
alteration is made to this boiler without permission, in writing,
Regulations, The Building Standards (Scotland) Regulations
from Hepworth Heating Ltd.
(applicable in Scotland), Local Water Company Bye-laws, The
Any alteration that is not approved by Hepworth Heating Ltd.,
Health and Safety at Work Act, Control of Substances Hazardous
could invalidate the B.S.I. Certification of the boiler, warranty
to Health, The Electricity at Work Regulations and any local
and could also infringe the current issue of the Statutory
regulations which may apply.
Requirements.
5 221790B
RETURN
PUMPED
PUMPED
FLOW
FLOW
GRAVITY
GRAVITY
RETURN
1 General Data
1.5 Gas Supply
DATA TABLE 1.
The gas installation shall be in accordance with the current
TOTAL DRY
issue of BS6891.
47.5kg
WEIGHT
(105lb)
The supply from the governed meter must be of adequate size ( I n c l u d i n g
Terminal)
to provide a steady inlet working pressure of 20mbar (8in wg) at
the boiler.
37kg
LIFT WEIGHT
(82lb)
On completion test the gas installation for soundness using the
pressure drop method and suitable leak detection fluid, purge
WATER
in accordance with the above standard.
2.95Litre
CONTENT
(0.65gal)
1.6 Electrical Supply
GAS
WARNING. This boiler must be earthed.
1
Rc /2 in.
CONNECTION
All system components shall be of an approved type and shall
WATER
comply with and be connected in accordance with the current
4 x 22mm copper pipes from
issue of BS7671 and any applicable local regulations. CONNECTION
top of case
Connection of the boiler and system controls to the mains
ELECTRICITY
supply must be through a common isolator and must be fused
230V~50Hz, fused 3A.
SUPPLY
3A, maximum. This method of connection must be by a fused
double pole isolating switch, with a minimum contact separation
Bottom right hand side of case
DATA LABEL
of 3mm on both poles. The switch should be readily accessible
and preferably adjacent to the appliance. It should supply the
appliance only and be easily identifiable as so doing.
TABLE 2.
Alternatively, an unswitched shuttered socket outlet and 3A
min medium max
fused 3 pin plug both to the current issue of BS1363 may be RANGE RATING
used, provided that they are not used in a room containing a
NOMINAL kW
14.84 16.58 18.32
bath or shower.
HEAT
INPUT(GROSS) Btu/h
50,630 56,565 62,500
Wiring to the boiler must be PVC insulated type to the current
issue of BS6500 Table 16, not less than 0.75mm2 (24/0.20mm).
NOMINAL kW
11.72 13.19 14.65
HEAT
1.7 Contents of Packaging
40,000 45,000 50,000
OUTPUT Btu/h
There are two packs, one contains the boiler, refer to Section 4.1
BURNER m bar
7.5 9.8 12.3
for contents.
SETTING
PRESSURE in.w.g 3.0 3.9 4.9
The other pack contains the balanced flue terminal assembly,
wall duct and flue hood assembly.
APPROX m3/h
1.44 1.61 1.77
Refer to Section 2.3 to check that the flue terminal assembly GAS
51 57 62.5
RATE ft3/h
supplied is suitable.
BURNER INJECTOR MARKING: 203096
1.8 Water System
This boiler shall only be used on an unrestricted open vented
PILOT INJECTOR MARKING: 7215
system with the water supply taken from a feed and expansion
cistern having a head of 27m (90ft) maximum.
1.10 Safety Valve
This boiler must not be connected to a sealed water system.
A safety valve need not be fitted to an open vented system.
1.9 Drain
1.11 Location
System
This boiler is not suitable for outdoor installation.
A draining tap must be provided at the lowest points of the
This boiler may be installed in any room, although particular
system which will allow the entire system, boiler and hot water
attention is drawn to the requirements of the current issue of
cylinder to be drained.
BS7671 with respect to the installation of a boiler in a room
Draining taps should be to the current issue of BS2879.
containing a bath or shower. Any electrical switch or boiler
control utilising mains electricity should be placed so that it
Boiler
cannot be touched by a person using the bath or shower.
The electrical provisions of the Building Standards (Scotland)
A draining point is fitted at the bottom right hand side of the heat
Regulations apply to such installations in Scotland.
exchanger. Cover controls to avoid water damage. If required
remove the combustion chamber front cover to improve access.
The boiler must be mounted on a flat wall which is sufficiently
robust to take its total weight.
221790B 6
1 General Data
1.12 Boiler Clearances
Refer to diagram 1.2.
This boiler must be positioned so that at least the minimum
operational and servicing clearances are provided.
Additional clearances may be required for installation.
If fixtures are positioned next to the boiler they should be made 500mm
removable for access to pipework.
TOP VIEW
Sufficient clearance must be left in front of the boiler for
servicing.
Additional clearance may be
required for installation
1.13 Heating System Controls
The heating system should have installed: a programmer and
100mm
room thermostat controlling the boiler.
Thermostatic radiator valves may be installed in addition to the
room thermostat.
Note: For further information, see The Building Regulations
1991 - Conservation of fuel and power, 1995 edition - Appendix
6mm
6mm
G, table 4b.
65mm
FRONT VIEW
Diagram 1.2
2 Flue and Ventilation
Note: Detailed recommendations for flues are given in the
A suitable guard, reference Type  F , can be bought from:-
current issue of BS5440 Part 1.
Tower Flue Components Ltd
2.1 Terminal Position
Morley Road
Tonbridge
The minimum acceptable siting dimensions for the terminal
Kent. TN9 1RA
from obstructions, other terminals and ventilation openings are
shown in diagram 2.1.
2.3 Wall Thickness
The terminal must be exposed to the external air, the position
Check the thickness of the wall.
allowing free passage of air across it at all times.
Flues available are:-
Car ports or similar extensions of a roof only, or a roof and one
wall, require special consideration with respect to any openings,
Standard Pack:- 50BF Part No.446102
doors, vents or windows under the roof. Care is required to
Extension Pack:- Part No.424680 plus
protect the roof if it is made of plastic sheeting. If the car port
Standard Pack as above for 410 to 625mm (16 to 25in)
consists of a roof and two or more walls, seek advice from the
local gas company before installing the boiler.
Note: If the wall thickness is less than 280mm the wall duct and
flue ducts can be cut down, to a minimum length of 100mm.
If the terminal is fitted within 600mm below plastic guttering or
painted soffit an aluminium shield 1500mm long should be fitted
2.4 Room Ventilation
immediately beneath the guttering or eaves. If the terminal is
fitted within 450mm below painted eaves or a painted gutter, an
The boiler is room sealed and does not require the room or
aluminium shield 750mm long should be fitted immediately
space containing it to have permanent air vents.
beneath the guttering or eaves.
2.2 Terminal Guard
A terminal guard is required if persons could come into contact
with the terminal or the terminal could be subject to damage.
If a terminal guard is required, it must be positioned to provide
a minimum of 50mm clearance from any part of the terminal and
be central over the terminal.
7 221790B
3792
2 Flue and Ventilation
2.5 Boilers in a Compartment
COMPARTMENT AIR VENT TABLE
Where the installation of the boiler will be in an unusual position,
COMPARTMENT
special requirements are needed, the current issue of BS6798
HIGH LEVEL LOW LEVEL
VENTILATION
gives detailed guidance on these requirements.
REQUIREMENTS VENT AREA VENT AREA
A compartment used to enclose the boiler must be designed
and constructed specifically for this purpose. An existing
cupboard or compartment modified for the purpose may be
VENTILATION
used. Details of essential requirements for cupboard or
165cm2 25in2 165cm2 25in2
FROM ROOM
compartment design are given in the current issue of BS6798.
OR SPACE
The doorway opening should be of sufficient size to allow for
FROM
easy removal of the boiler.
83cm2 12.5in2 83cm2 12.5in2
OUTSIDE
Where the boiler is fitted in a cupboard or compartment,
permanent high and low level ventilation must be provided. The
minimum ventilation areas required are given in Table 3.
2.6 Timber Frame Building
C
If the boiler is to be installed in a timber frame building it should A
be fitted in accordance with the Institute of Gas Engineers
B,C
document IGE/UP/7/1998. If in doubt seek advice from the local
B,C
K
gas undertaking or Hepworth Heating Ltd.
L
L
G
A K
K
F
F
F
A
G
E G
G
G
Under Car Port etc.
D
J
F
K
H,I
MINIMUM SITING DIMENSIONS FORBALANCED FLUE
TERMINALS
MINIMUM
POSITION SPACING (mm)
A DIRECTLY BELOW AN OPENABLE
WINDOW, AIR VENT, OR ANY OTHER
VENTILATION OPENING 300
B BELOW GUTTER, DRIAN/SOIL PIPE 300
C BELOW EAVES 300
D BELOW A BALCONY OR CAR PORT 600
E FROM VERTICAL DRAIN PIPES AND
SOIL PIPES 75
F FROM INTERNAL OR EXTERNAL
CORNERS 250
G ABOVE ADJACENT GROUND OR
BALCONY LEVEL 300
H FROM A SURFACE FACING THE
TERMINAL 600
I FACING TERMINALS 600
J FROM OPENING (DOOR/WINDOW) IN
CAR PORT INTO DWELLING 1200
K VERTICAL FROM A TERMINAL 1500
L HORIZONTALLY FROM A TERMINAL 300
Diagram 2.1
221790B 8
3815A
3 Water Systems
The installation of the boiler must comply with the requirements
OPEN VENTED FULLY PUMPED WATER SYSTEM
of the current issue of BS6798. RECOMMENDED RELATIONSHIP BETWEEN
PUMP COLD FEED AND VENT
3.1 Frost Protection
22mm VENT
450mm (MIN.)
If the position of the boiler is such that it may be vulnerable to
MIN.
freezing it should be protected as specified in the current issue
HEIGHT
of BS5422. It is recommended that a frost protection thermostat
be fitted.
15mm (MINIMUM)
3.2 Pump
COLD FEED
The pump, with integral valves, should be fitted in the heating
FEED AND
flow pipework from the boiler, it should be set to produce a
EXPANSION
temperature difference of 11oC (20oF), between the flow and
CISTERN
return, with the control thermostat set at  MAX , which is about
1150mm
82oC (180oF).
MIN.
The resistance through the boiler can be found from diagram 3.1.
High resistance microbore systems may require a higher duty
pump.
PUMP
3.3 Bypass - Fully Pumped Water System
There must always
A bypass is usually unnecessary on systems using a 3 port
FLOW
be a cold water path
150mm
diverter valve since one port will remain in the open position at
to the return
MAX.
all times. This allows satisfactory operation of the pump
connection
overrun.
of the boiler.
RET.
However if thermostatic radiator valves are fitted to all radiators
IF REQUIRED
or two port valves are used a bypass is required.
15mm (MINIMUM)
BOILER
The bypass connection must be at least 2 metres away from the
BY-PASS WITH
boiler.
LOCKSHIELD VALVE
Diagram 3.2
The flow through the boiler must not be allowed to fall such that
there is a temperature difference greater than 20oC between the
flow and return.
3.4 Water System
The cold feed must be 15mm minimum size.
It is important that the relative positions of the pump, cold feed
and open vent are as shown in diagram 3.2.
28mm
The unrestricted open vent from the boiler must rise continuously
PIPE
to discharge over the feed and expansion cistern.
22mm
28mm
PIPE
PIPE
22mm
PIPE
COMPRESSION
Note: When cutting leave
sufficient length for fittings
JOINT
1000
22mm VENT
15mm COLD FEED
750
INDIRECT CYLINDER
500 (Shown with
1m MIN.
recommended
27m MAX.
250
thermostat and valve)
HEATING
0
SYSTEM
5 10 15
0 20 25 30
PUMP
28mm
VIEWED
Flow rate (litres/minute)
REFER TO BS5546
FROM
Diagram 3.1 Diagram 3.3
PRESSURE LOSS OF BOILER FRONT
9 221790B
6455
RETURN
FLOW
CYLINDER
HEATING
3794
FLOW
RETURN
FLOW (GRAVITY)
RETURN (GRAVITY)
4632
(mm head of water)
Water pressure loss
3 Water Systems
3.5 Domestic Hot Water System
General. The domestic hot water service must be in accordance
FLOW
with the current issue of BS5546, refer also to the current issue
of BS6700.
RETURN
22mm
PIPE
3.6 Indirect Cylinder
For all systems supplying domestic hot water the cylinder must
be indirect. It is recommended that the indirect cylinder be fitted
with some form of temperature control.
3.7 Gravity Domestic Hot Water with Pumped
Heating
Important: If domestic hot water is to be provided by a gravity
circulation to the indirect cylinder the blanked off connections
must be opened and used, using 22x28mm connections, see
diagram 3.3.
3.8 Fully Pumped Heating and Domestic Hot
Water
The connections for this type of system MUST be as shown in
diagram 3.2 and 3.4.
22mm VENT & 15mm COLD FEED
TO BE FITTED IN ACCORDANCE
3.9 Inhibitor
WITH BS 5449
Attention is drawn to the current issue of BS5449 and BS7593
on the use of inhibitors in central heating systems.
If an inhibitor is to be used, contact a manufacturer or
Hepworth Heating Ltd., for their recommendations as to the
INDIRECT
best product to use.
CYLINDER
IF REQUIRED
When installing in an existing system take special care to drain
1metre Min. ALTERNATIVE
BYPASS 15mm
27 metres SYSTEM
the entire system, including radiators, then thoroughly cleaning
MIN WITH
Max. CONTROL
out before installing the boiler whether or not adding an inhibitor. LOCKSHIELD
VALVES
VALVE
HEATING
SYSTEM
PUMP
FULLY PUMPED CIRCULATION
SYSTEM (DIAGRAMMATIC)
Diagram 3.4
221790B 10
4107
6461
4 Flue and Appliance Preparation
4.1 Unpacking
WALL TEMPLATE
BALANCED
FLUE TERMINAL
Open the carton containing the boiler, remove the end fitting
which contains, wall mounting bracket, heat exchanger baffles PACK
and loose items pack. Check the items supplied against the
(Supplied separately)
contents list on the flap and diagram 4.1.
With the boiler still in the bottom tray, slide the controls cover
upward and remove it as shown in diagram 4.2. Remove the
LOOSE ITEMS
case by undoing the wing nuts and lifting the case off, see
PACK
diagram 4.2.
HEAT
Remove the packing piece from inside the case.
EXCHANGE
Place on one side until required.
BAFFLES
Place the boiler on one side until required.
4.2 Positioning
Select the boiler position. Take due account of the position of
the flue terminal, see diagram 2.1. WALL
MOUNTING
Use the template, making sure it is square and mark out the
BRACKET
position of the flue opening, see diagram 4.3.
BOILER
Cut a hole through the wall as neatly as possible.
Note. If the hole is oversize or of an irregular shape it must be
faced off to the hole dimensions shown.
Use template, again, making sure that it is positioned both
square and central to the flue hole, marking the fixing points at
the top, bottom and clearance holes for wall duct.
INSTALLATION
Remove the wall template after marking, then check marked & SERVICING
CARTON
positions against diagram 4.3.
LITERATURE
CONTENTS LIST
Drill holes to accept the plugs and screws supplied in the loose
Diagram 4.1
Printed on carton flap
items pack.
Secure the bottom bracket to the wall, using the plugs and
screws.
CONTROLS COVER
Make sure the bracket is level.
Drill a 7mm clearance hole to a depth of 10mm.
SECURING WING NUTS (2)
Fit plugs into top fixing holes and fit screws, leaving about 5mm
proud.
CASE
Take the balanced flue assembly and wall duct from its carton,
place the balanced flue assembly on one side until it is required.
Note. If fitting a short flue it will be necessary to cut wall duct,
see Table 4.
Position the wall duct, see diagram 4.4.
CARTON
Diagram 4.2
11 221790B
3795
3796
4 Flue and Appliance Preparation
C
L
112 7mm dia. drill
112
*
*
122
122
No. 12 X 2" long
woodscrew
168
wall
plug
325
35
5mm
C
L
SECURING
220
SCREWS (2)
CLEARANCE
FIXING
FIXING HOLE (2)
*
POINTS
POINTS
420
CLEARANCE
FLUE
HOLE
HOLE
SECURING
CLIPS
119 119 WALL
DUCT
MOUNTING
*
* BRACKET
Diagram 4.4
Diagram 4.3
221790B 12
3798
3797
5 Boiler Installation
5.1 Mounting the Boiler
Remove the boiler from the carton tray.
If necessary, for a gravity domestic hot water system cut the
FOAM
pipes as shown in diagram 3.3.
SEAL
Stand boiler upright on the packaging, to protect the paintwork.
Stick the foam seal around the boiler flange, at the back, making
sure it is a tight fit, around the corners, see diagram 5.1.
Fit suitable fittings to the pipework.
Now make sure that the top, swing brackets are UPRIGHT, see
diagram 5.2.
Lift the boiler into position, hooking over the bottom wall bracket.
Swing the brackets over the two screws at the top and secure,
see diagram 5.2.
Secure the boiler to the flange on the wall duct, see diagram 5.3.
Note. For a short flue it will be necessary to cut the balanced flue
assembly, see Table 4.
Diagram 5.1
Take the balanced flue assembly from its carton and remove the
four screws to release the outer baffle, wire guards and inner
baffle flue duct assembly, from the air duct assembly, see
diagram 5.4.
SWING
From the outside place the air duct assembly into the hole in the
BRACKET
wall, fit it around the wall duct, slide in until the wall plate touches
the wall surface. Make sure the air duct wire guards are in
position.
Seal the joint in the air ducts with the yellow tape provided. Tape
four pieces into the four inside corners, followed by four along
the joints overlapping the corner pieces, to make a good seal,
see diagram 5.4A. Allow a minimum of 20mm (3/4in) overlap of
the ductings.
PIPES
SECURING
Take the flue hood assembly, remove the access door, secure
REMOVED
SCREW (2)
the assembly to the boiler, with the screws provided in the loose
FOR CLARITY
items pack, see diagram 5.5.
Place the inner baffle and flue duct assembly into the hole in the
wall outside, fit it around the flue duct on the boiler and slide it
in until it touches the air duct assembly wire guards.
Seal the flue duct joint on the inside with the heat resistant semi-
transparent tape provided, see diagram 5.4A.
Cement around the wall plate.
To complete the flue terminal assembly, refit wire guards, outer
baffle and secure with screws.
Fit the boiler flue baffles, see diagram 5.6.
Refit the flue access door.
MOUNTING
BRACKET
MOUNTING THE BOILER
Diagram 5.2
13 221790B
3799
3800
5 Boiler Installation
5.2 Water Circulation System 5.4 Control Box
Complete the water connections to the boiler. Remove the electrical control box securing screw, see diagram
5.7. Pull the control box down at the front and support on the
Fill, vent and cold flush the system as recommended in the
hook at the rear of the control box cover, see diagram 5.8.
current issue of BS6798.
Check for any water leaks and put right.
5.3 Gas Connection
Make the gas connection to the Rc1/2in gas service cock.
Check for leaks using a suitable leak detection fluid.
TABLE 4.
SHORT FLUE 100-280 CUTTING LENGTHS
AIR DUCT FLUE DUCT
Wall Air Flue
WALL Inner Baffle
Duct Duct Duct Flue Duct
THICKNESS
100-150
70 190 190 70
SECURING
SCREW (2)
150-200 20 190 190 20
200-280 0 130 130 0
Diagram 5.3
WALL
PLATE
INNER BAFFLE/
WALL DUCT
FLUE DUCT
ASSEMBLY
SCREW (4)
AIR DUCT
ASSEMBLY
WIRE
GUARDS
OUTER
BAFFLE
Diagram 5.4
221790B 14
3801
3802
5 Boiler Installation
5.5 Electrical Connection 5.6 Testing
Thread the mains cable through the cable clamp in the rear of Checks to ensure electrical safety must be carried out by a
the box and connect to the terminal strip, see diagram 5.8 and competent person.
5.9.
After installation of the system, preliminary electrical system
Standard colours are, brown - live (L), blue - neutral (N) and checks as below should be carried out:
green and yellow - earth (E).
1. Test insulation resistance to earth.
The mains cable outer insulation must not be cut back external
2. Test earth continuity and short circuit of all cables.
to the cable clamp.
3. Test the polarity of the mains.
Make sure the cable is suitably secured.
Refit the control box.
When making connections, make sure that the earth conductor
The installer is requested to advise and give guidance to the
is made of a greater length than the current carrying conductors,
user of the controls scheme used with the boiler.
so that if the cable is strained the earth conductor would be the
last to become disconnected.
FLUE
DUCT
FLUEWAY
ACCESS
DOOR
SECURING
SCREW (2)
FLUE DUCT/
AIR
FLUE HOOD
DUCTS
YELLOW
SEALING
TAPE
5mm
SECURING
SCREWS (4)
FLUE HOOD
Diagram 5.5
ASSEMBLY
BAFFLE (4)
SEMI-TRANSPARENT
SEALING TAPE
1350
Diagram 5.4A
Diagram 5.6
15 221790B
3804
3803
3805
5 Boiler Installation
KEY
br BROWN
g/y GREEN/YELLOW
bl BLUE
bk BLACK
230V~50Hz
MAINS SUPPLY
FUSED AT 3A
L N
L N
EARTH
g/y
bk
SECURING bl
g/y
bl
SCREW
g/y
Diagram 5.7
br
br
HOOK
CONTROL
MULTI-
BOX COVER
FUNCTIONAL
CONTROL CABLE
CONTROL
THERMOSTAT
bk
MULTI-FUNCTIONAL
EARTH
CONTROL
Diagram 5.9
MAINS
CABLE
TERMINAL
THERMOSTAT
CONTROL
CAPILLARY
THERMOSTAT
Diagram 5.8
221790B 16
8040
8051
8038
6 Commissioning
Please ensure the "Benchmark" logbook is completed and left
Turn on the main gas supply and purge in accordance with the
with the user.
current issue of BS6891.
Turn boiler gas service cock  C  On .
6.1
Push in control button  K , keep pressed in and at the same time
Make sure that the system has been thoroughly flushed out with
operate the piezo unit button  G until the pilot burner lights.
cold water without the pump in place.
After the pilot burner lights keep the button  K pushed in for 20
Refit the pump, fill the system with water, making sure that all
seconds. If the pilot fails to stay alight a safety device in the
the air is properly vented from the system and pump.
multi-functional control prevents immediate relighting.
Before operating the boiler check that all external controls are
Do not attempt to relight until the safety device has reset, that is,
calling for heat.
after a minimum of three minutes.
Make sure that the pilot is alight and stable, view through
6.2 Initial Lighting and Testing
window  H .
CAUTION. This work must be carried out by a competent
Check the length of the pilot flame, it should envelop the
person, in accordance with the current issue of BS6798.
thermocouple tip as shown in diagram 6.2. The pilot rate can be
Make sure that all naked lights and cigarettes are out.
adjusted, if necessary, by turning the pilot burner adjustment
screw  N , having first removed the multi-functional control
Identify the controls by reference to diagram 6.1.
cover by releasing the screw, see diagram 6.1. Check the pilot
Turn the control thermostat knob  B to  O the Off position.
supply connection for gas soundness, using a suitable leak
detection fluid.
Remove gas pressure test point screw  E and fit a suitable
pressure gauge.
Fit the case by hooking it under at the top and securing with the
wing nuts previously removed, see diagram 6.3.
Turn the electrical supply on and check that all remote controls
are calling for heat. Check that the pump is circulating water
Set the control thermostat knob  B between  MIN and  MAX
through the system.
-  MAX is about 82oC (180oF) and check that the burner lights
smoothly. Check all the gas connections for soundness with a
suitable leak detection fluid.
To set the burner pressure, operate the boiler for ten minutes,
H
adjust the gas rate screw  F , see diagram 6.1 until the required
A
pressure is obtained, see relevant Table 2 for setting pressures.
D M K C
Should any doubt exist about the gas rate, check it using the gas
meter test dial and a stop watch, at least ten minutes after the
burner has lit, make sure that all other gas burning appliances
and pilot lights are off.
Gas Rates After 10 Minutes
G B
m3/h 1.70
F
ft3/h 60.0
These figures are offered as a guide only.
Stick the self adhesive arrow, from the loose items pack, in the
A ELECTRICAL
appropriate place of the  MIN  MED and  MAX column of the
N
Data Label.
CONTROL BOX
B THERMOSTAT
Remove the pressure gauge and refit the test point screw,
CONTROL KNOB
making sure a gas tight seal is made.
C GAS SERVICE
COCK (SHOWN IN
12 to 14mm
OFF POSITION)
D MULTI-FUNCTIONAL
CONTROL
2 to 4mm
E PRESSURE TEST
E
NIPPLE
F GAS BURNER
PRESSURE SCREW
G PIEZO UNIT BUTTON
H WINDOW PILOT
K CONTROL BUTTON (GAS)
M COVER SECURING SCREW
N PILOT BURNER PRESSURE
SCREW
Diagram 6.1 Diagram 6.2
17 221790B
8042
8046
3810
6 Commissioning
6.3 Testing
6.7 Protection Against Freezing
To check the operation of the flame failure device, turn the gas
If the boiler is to be out of use for a period of time during severe
cock  Off .
weather conditions we recommend that the whole of the system
including the boiler, be drained off to avoid the risk of freezing
The multi-functional control should shut down within 60 seconds,
up.
indicated by a  click from the multi-functional control.
Turn gas cock  On and relight the burner.
Allow the system to reach maximum working temperature and
examine for water leaks.
There should be no undue noise in the system and no pumping
over of water or entry of air at the open vent above the feed and
expansion cistern.
The boiler should then be turned off and the system drained off
as rapidly as possible, whilst still hot.
ENSURE
6.4 Adjustment - Fully Pumped Water System
CASE ENGAGEMENT
When commissioning the system the boiler should first be fired
with the bypass fully closed on full service, that is, central
heating and domestic hot water. The system should then be
balanced, adjusting the pump and lockshield valve as necessary.
Having achieved a satisfactory condition operate the boiler with
the bypass fully closed on minimum load, normally this will be
central heating only with one radiator in the main living area
operating. The bypass valve should be gradually opened to
achieve the design temperature difference between the flow
and return.
CASE
UNDER NO CIRCUMSTANCES SHOULD THIS VALVE BE
LEFT IN THE FULLY CLOSED POSITION.
Note. Operate the boiler on full service and check the balancing,
making further adjustments as necessary.
Do not attempt to adjust the control thermostat calibration.
6.5 Thermostatic Radiator Valves
If thermostatic radiator valves are fitted care must be taken to
make sure that an adequate flow rate through the boiler when
they close, refer to the current issue of BS7478 for guidance.
6.6 Completion
Fit the controls cover by hooking into the sliders and pushing it
CONTROLS
back as far as it will go, see diagram 6.3. Diagram 6.3
COVER
Instructions to the User
7 Instructions to the User
Instruct and demonstrate the safe and efficient operation of the It is the Law that servicing is carried out by a competent person.
boiler, heating system and domestic hot water system.
Advise the user of the precautions necessary to prevent damage
Advise the user, that to ensure the continued efficient and safe to the system and building in the event of the heating system
operation of the boiler it is recommended that it is checked and being out of use during frost and freezing conditions.
serviced at regular intervals. The frequency of servicing will
Reminder, leave these instructions and the  Benchmark logbook
depend upon the particular installation and usage, but in general
with the user.
once a year, preferably at the end of the heating season should
be enough.
Draw attention, if applicable, to the current issue of the Gas
Safety (Installation and Use) Regulations, Section 35, which
imposes a duty of care on all persons who let out any property
containing a gas appliance.
221790B 18
3811
8 Servicing
Notes: To ensure the continued efficient and safe operation of
the boiler it is recommended that it is checked and serviced as
FLUEWAY
necessary at regular intervals. The frequency of servicing will
ACCESS
depend upon the particular installation conditions and usage,
DOOR
but in general once a year, preferably at the end of the heating
season should be enough.
It is the Law that any servicing is carried out by a competent
SECURING
person.
SCREW (2)
Before servicing turn off the gas and isolate the electrical supply
to the boiler.
After completing a service always test for gas soundness and
SECURING
carry out functional check on controls.
SCREW (4)
Unless stated otherwise all parts are replaced in the reverse
order to removal.
8.1 Access
COMBUSTION
Refer to diagram 6.3 and slide the controls cover forwards and
CHAMBER
off.
FRONT
Diagram 8.1
Undo the wing nuts and remove the case.
When refitting the case check the condition of the case seal, if
it needs replacing refer to Section 10.12.
SPARK
PILOT
8.2 Main Burner
ELECTRODE
BURNER
Remove the flueway access door by removing the screws, see
diagram 8.1.
THERMOCOUPLE
Remove the combustion chamber front, see diagram 8.1.
SPRING
Disconnect the pilot pipe union connector and ignition lead, see
CLIP
diagram 8.2.
Separate the pilot assembly from the main burner, by removing
the pilot shield securing nut, shakeproof washer and move to
the right. Remove the burner securing nut and wing nut from the
PILOT
burner support bracket, remove the burner support bracket, see
INJECTOR
diagram 8.3.
To remove the main burner from the main injector at the rear,
PILOT
raise the burner up and forwards, easing the pilot pipe to the
UNION
side, to clear, take care not to damage the combustion chamber
CONNECTOR
insulation or the pilot burner assembly.
PILOT
Use a vacuum cleaner or suitable stiff brush to clean the burner
SHIELD
IGNITION
thoroughly, making sure that all the burner ports are clear and SECURING
LEAD
unobstructed. Diagram 8.2
NUT
Do not use a brush with metallic bristles.
SECURING
BURNER
NUT
BURNER
SUPPORT
BRACKET
WING NUT
Diagram 8.3
19 221790B
3812
3813
3814
8 Servicing
8.3 Cleaning Heat Exchanger
Place a sheet of paper in the base of the combustion chamber.
Remove the baffles from the heat exchanger, note, when
replacing, the 50BF is marked  TOP FRONT , see diagram 5.6.
MAIN
Clean the heat exchanger, paying particular regard to the gaps
INJECTOR
between the fins, with a suitable stiff brush.
Do not use a brush with metallic bristles.
Remove the paper together with any debris.
8.4 Main Injector
The main injector can be inspected and cleaned as necessary.
If removing for cleaning do not use a wire or sharp instrument
on the hole.
Use a little suitable sealant on the external thread when refitting
BURNER
to make sure a gas tight seal is made.
Diagram 8.4
8.5 Electrode, Pilot Burner and Pilot Injector
Release the thermocouple by removing the spring clip, pull the
thermocouple down from the pilot assembly, see diagram 8.2.
Inspect and clean pilot burner assembly.
Remove the pilot injector by unscrewing from the pilot burner
assembly, clean by blowing through it.
Note. On refitting and after cleaning the heat exchanger and
main burner make sure the main burner is fitted correctly, that
is, located on the main injector and horizontal, see diagram 8.4.
221790B 20
3815
9 Fault Finding
PILOT WILL NOT LIGHT
START HERE
Check gas line - open all cocks, Does pilot stay alight when
rectify any blockages, purge out multi-functional control knob is
any air. Does pilot light? released?
NO YES YES
NO
Apply match to pilot burner instead of
pressing piezo unit button. PILOT SATISFACTORY
Does pilot light?
NO YES
Undo tubing nut at pilot burner. Does pilot flame
Press multi-functional control knob. envelope thermocoupling?
Does gas flow freely?
NO YES NO YES
Rectify blockage in pilot injector, Check aeration. If necessary -
or renew pilot injector. Clean pilot, rectify blockage in pilot
injector, or replace.
Undo tubing nut at pilot outlet Check thermocoupling circuit using
of gas valve. Press gas valve knob. Thermocoupling Fault - Finding
Does gas flow freely? diagram.
NO YES
On pressing piezo unit button
Change blocked pilot tube. is there a spark across
electrode gap?
NO YES
Pull ignition lead off electrode.
Change multi-functional control. Hold end of lead close to pilot
burner and operate piezo unit.
Is there a spark across gap?
NO YES
Pull ignition lead off piezo unit.
Using blade of a screwdriver, touch
unit chassis and leave approx.
4mm gap from connection tag on
piezo unit. Operate piezo.
Is there a spark across gap?
NO YES
Change Change
piezo unit. ignition unit.
Check electrode gap. Reposition, or
replace electrode as necessary.
Diagram 9.1
21 221790B
0032M
9 Fault Finding
THERMOCOUPLE FAULT FINDING
Is the connection between the
NO
thermocouple and the multi-functional
Clean contacts and re-connect
control clean and tight ?
See diagram 9.2A, "Connection A"
YES
NO
Is the pilot flame correct length?
Check pilot injector and regulate pilot
Approxomately 12mm.
YES
Check the thermocouple output
(8-15mV, closed) or replace thermocouple.
NO
Change multi-functional control
Reference should be made to procedure 7,
British Gas Multimeter Instruction Book.
Does the pilot now stay alight ?
Diagram 9.2
9.1 Pilot
Refer to Chart 9.1.
9.2 Thermocouple
To test the thermocouple a meter with a range of 6 to 30mV is
required together with a thermocouple interrupter test unit.
Refer to thermocouple fault finding chart, diagram 9.2 and
CONNECTION 'A'
diagram 9.2A.
MULTI-FUNCTIONAL
9.3 Electrical
CONTROL
Important. On completion of the service/fault finding task which
has required the breaking and remaking of the electrical
connections the earth continuity, polarity, short circuit and
resistance to earth checks must be repeated, using a suitable
multimeter.
Refer to Fault Finding, Wiring and Functional Flow diagram 9.3
and 9.4.
Diagram 9.2A
221790B 22
4634
3816
9 Fault Finding
ELECTRICAL FAULT FINDING
Ensure that all services are available at the
appliance. ie. Gas, Electricity, Water.
Also turn control thermostat fully on and
check to see if pilot is lit.
Isolate the supply. Gain access to the control
box, check all connections etc.
Restore supply. Using multimeter set at 230V. AC.
Check supply fuses. Renew if
NO
With remote controls (if fitted) calling for heat
necessary. If ok then fault lies withtin
is there 230V between L & N
remote controls. Inform customer.
YES
Isolate supply. Remove gas valve
YES
NO
Does main burner light. cover. Check continuity of multi-
functional control wire harness.
Continuity ok ?
YES
NO
NO
Restore supply. Is there 230V between Replace multi-functional control harness
"L" & "N" on multi-functional control?
YES
Faulty multi-functional control. Renew.
Faulty control thermostat. Renew
YES
NO
Faulty pump, inform customer.
Does pump run ?
YES
CONTROLS IN ORDER
MAIN TERMINALS STRIP
Diagram 9.3
23 221790B
9007
9 Fault Finding
FUNCTIONAL FLOW
MAIN TERMINAL STRIP
CONTROL THERMOSTAT
bk br
PERMANENT
LIVE
230V ~ 50HZ
bl
N
N
FUSED
L
AT 3A
CONTROL MULTI- FUNCTIONAL
THERMOSTAT CONTROL
Diagram 9.4
10 Replacement of Parts
Replacement of parts must only be carried out by a competent
PHIAL
person.
Gain access as Section 8.1
Before replacing any parts isolate the boiler from the electrical SPLIT
supply and turn the gas supply off at the gas service cock,
PIN
indicator slot to be vertical.
Unless stated otherwise, all parts are replaced in the reverse
order to removal.
After replacing any parts always test for gas soundness and if
PHIAL POCKET
necessary carryout functional check of controls.
10.1 Control Thermostat - diagram 10.1
Open and support the electrical control box, refer to Section 5.4.
Remove the control knob. Remove the electrical connections
from the control thermostat body.
Release the control thermostat body by unscrewing the two
screws and shakeproof washers in the front of the control box.
Remove the split pin and withdraw the control thermostat phial
from its pocket. Remove the control thermostat complete from
GLAND
the boiler.
SEAL
Re-assembly note. When fitting the control thermostat, make
sure that the control thermostat phial is covered with heat sink
compound and then fully inserted into the phial pocket and that
the capillary is within the gland seal. Remake the electrical
CAPILLARY
connections. There must be no kinks or sharp bends in the
capillary.
Make sure that the capillary is positioned so that it passes
through the cut out in the control box.
10.2 Pilot Burner and Pilot Injector
SECURING
Proceed as relevant parts of Section 8.2 and 8.5.
SCREW (2)
10.3 Electrode - diagram 8.2
Proceed as relevant parts of Section 8.2, release the electrode
by removing the spring clip.
10.4 Piezo Unit - diagram 10.2
Open and support the electrical control box, refer to Section
CONTROL
5.4.
THERMOSTAT
Disconnect the ignition lead at the piezo unit.
CONTROL KNOB
Diagram 10.1
221790B 24
8050
3817
8041
10 Replacement of Parts
Note: To ease the removal of the piezo unit it is advisable to
temporarily remove the boiler thermostat from the control box,
refer to Section 10.1.
Depress the retaining tabs and remove the Piezo unit.
10.5 Thermocouple - diagram 10.3
Proceed as relevant parts of Sections 8.2 and 8.5.
Unscrew thermocouple nut.
When refitting do not tighten the thermocouple nut more than a
quarter turn beyond finger tight. IGNITION
LEAD
10.6 Multi-functional Control - diagram 10.3
Remove the screw to release the multi-functional control cover.
Disconnect the electrical leads, thermocouple and pilot supply
pipe at the valve.
Undo the four screws each side of the multi-functional control to
release the gas service cock and the burner supply pipe, take
care not to damage the  O ring seals.
Remake the connections.
Do not tighten the thermocouple nut more than a quarter turn
CONTROL
beyond finger tight.
BOX
It will be necessary to purge the pipework and the multi-
functional control before relighting, refer to  Commissioning .
RETAINING
Refit multi-functional control cover. TABS
10.7 Solenoid - diagram 10.4
PIEZO UNIT
With the multi-functional control cover removed disconnect the Diagram 10.2
electrical leads, remove the retaining clip and solenoid.
10.8 Main Burner
COVER
Remove the main burner as Section 8.2.
SECURING
GAS
SCREW
COVER
10.9 Main Injector
SERVICE
COCK
Remove the main injector as Section 8.4.
10.10 Insulation - diagram 10.5
Combustion Chamber Front
Remove the combustion chamber front as Section 8.2. Remove
the retaining screw and slide the insulation out. .
BLUE
GREEN/YELLOW
Sides
BURNER
Slide the insulation pads out.
BROWN
SUPPLY
PIPE
Rear
With the side pads removed the rear pad can now be removed.
10.11 Viewing Window - diagram 10.6
Remove the old self adhesive aluminium foil gasket and the old
mica window. Replace with a new mica window. Peel off the
THERMOCOUPLE
PILOT SUPPLY
backing paper and secure with new self adhesive aluminium foil
NUT
PIPE
gasket, see diagram 10.6. Ensure no air bubbles are trapped
underneath the foil.
Important
Make sure that the mica window fully covers the opening and
that the hole in the aluminium foil gasket is centred over
opening.
Diagram 10.3
25 221790B
8039
3819
10 Replacement of Parts
MULTI-FUNCTIONAL
CONTROL
SOLENOID
BRACKET
SOLENOID
COVER
ELECTRICAL
RETAINING
CONNECTIONS
SOLENOID
Diagram 10.4
CLIP
REAR INSULATION PANEL
MICA WINDOW
OPENING
(INSIDE FACE OF
THE BOILER
FRONT COVER)
SIDE INSULATION
PEEL OFF
PANELS
BACKING
PAPER
SELF ADHESIVE
COMBUSTION
ALUMINIUM FOIL
GASKET
CHAMBER FRONT
Diagram 10.6
10.12 Case Seal
To remove the seal, carefully bend up the tabs.
Remove the seal, making sure that all the old adhesive is
removed.
COMBUSTION
When fitting the new seal, make sure that it fits into the corners
CHAMBER FRONT
and has not buckled.
INSULATION
Carefully bend the tabs down.
Diagram 10.5
221790B 26
3820
7907
3821
11 Spare Parts
11.2 Ordering
11.1 Part Identification
When ordering any spare parts please quote the number and
The key number on the diagram and the list will help to identify
description from the list together with the model name and serial
the part.
number.
If ordering from British Gas also quote the GC number of the
appliance and part.
6
5
4
1
12
7
2
6a
9
11
3
8
10
Diagram 11.1
Key No Part No Description GC Part No
1 429549 Multi-functional control 312 926
2 208040 Joint ring 334 592
3 203096 Injector - 50BF 313 305
4 202432 Thermocouple E00 999
5 K3580 Clip - thermocouple 390 983
6 203429 Pilot burner 379 021
7 202621 Spark electrode 379 020
8 WW4609 Ignition lead 136 464
9 800399 Thermostat - control 313 915
10 204687 Control knob *********
11 202713 Piezo igniter *********
12 801236 Mica window and gasket
27 221790B
8048
Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.
221790B 28


Wyszukiwarka

Podobne podstrony:
Glow Worm installation and service manual Ultimate 60CF UIS
Glow Worm installation and service manual Hideaway 50BF UIS
Glow Worm installation and service manual Ultimate 60BF UIS
Glow Worm installation and service manual Ultimate 50CF UIS
Glow Worm installation and service manual Ultimate 40BF UIS
Glow Worm installation and service manual Ultimate 40CF UIS
Glow Worm installation and service manual Ultimate 30BF UIS
Glow Worm installation and service manual Hideaway 60CF UIS
Glow Worm installation and service manual Hideaway 100CF UIS
Glow Worm installation and service manual Hideaway 80CF UIS
Glow Worm installation and service manual Hideaway 80BF UIS
Glow Worm installation and service manual Miami GF UIS
Glow Worm installation and service manual Hideaway 70CF UIS
Glow Worm installation and service manual Hideaway 70BF UIS
Glow Worm installation and service manual Hideaway 40BF UIS
Glow Worm installation and service manual Hideaway 120BF UIS
Glow Worm installation and service manual Hideaway 120CF UIS
Glow Worm installation and service manual Energy Saver 40 UI
Glow Worm installation and service manual Hideaway 50CF

więcej podobnych podstron