{Change Comments ***********************************************************}
{6/5/89, changed tool path to force feed on first TP move after a tool change,added Metric, WFG}
{.62,1/24/90, added OP clearances for v3.2, WFG}
{1/29/90
Modified: Fanuc 10T MS [-] L001.69
Deleted ClearancePlane1# & FirstMoveEPX# prog format, they are not being used.
Deleted extra 4 lines not needed from fall thru if not canned cycle.
Added SetHome command, enables incremental ouput.
Deleted ZeroPosReg command, has no effect.
Jim Radcliffe}
{2/16/90
Modified: Fanuc 10T MS [-] L001.69.1
Added Feedrate to Approach sub.
Deleted FirstFeed sub & changed FirstFeed command to Feedrate in ToolPath.
Jim Radcliffe}
{2/20/90
Modified: Fanuc 10T MS [-] L001.69.2
Deleted extra StockOnNoCan command from Approach sub.
Added missing CheckOffset commands to Sametool.
Added FeedrateC commands to SameTool Feed lines.
Jim Radcliffe}
{5/10/90
Modified: Fanuc 10T MS [-] L001.69.3
Added missing CSS stuff for same tool where the last operation was not CSS.
Jim Radcliffe}
{5/30/90
Modified: Fanuc 10T MS [-] L001.69.4
Changed 1st axis moves in Approach to unconditional moves.
Jim Radcliffe}
{6/4/90
Modified: Fanuc 10T MS [-] L001.69.5
Commented out Feedrate in Approach & FeedrateC in SameTool, rapid to start point.
Jim Radcliffe}
{6/21/90
Modified: Fanuc 10T MS [-] L001.69.6
Commented out Feed in Approach & in SameTool, see last note.
Put back the FirstFeed sub and calls in ToolPath that was deleted earlier.
Jim Radcliffe}
{7/3/90
Modified: Fanuc 10T MS [-] L001.69.7
Modified Approach sub and Approach handling for SameTool.
Moved all ConstantSurfaceFeed output to common point of all operations.
Modified the FirstFeed sub to output Feedrate on FirstFeat of each operation.
Added comment restricting use of modifiers during EACHQuadrant/NEXTQuadrant loop.
DWB}
{.71, Added PSComments, minor fixes, 8/1/90, JR}
{9/25/90, Update to Version 3.2 per Fanuc 10T MS [-] L001.71.1 Format, DWB}
{10/2/90, Added StockOff globally at FirstOperation, DWB}
{10/8/90, Replace CalcRPM2 globally with CalcEPRPM# at end of prog, DWB}
{2/15/91,
Modified: Fanuc 10T MS [-] L001.71.3
Deleted PostScript handling of ProgStop and CoolOff related commands.
Added General Info 1 handling of ProgStop and CoolOff related commands.
Added Feed and FeedRate back in to Contour StartPoint Approach move, and Deleted FirstFeed sub.
Modified handeling of ConstantSurfaceSpeed for SameTool operations in CheckOffset sub.
Added code for handling Tap cycles correctly in ToolPath and at end of each Operation.
Deleted XTapAtZ from Thread feature line in ToolPath.
Added CheckRapid sub to output Rapid where needed.
Added AbsOrInc to FirstOperation to allow for incremental output.
Deleted Plane command from IF NewTool? because it is already set in FirstOperation.
Deleted XStkLast and ZStkLast from RoughContour canned cycle line, they are obsolete.
Modified Canned Drilling output to handle Tapping and AutoFinish better.
DWB}
{3/29/91, Update to Version 4.0 Format, DWB}
{4/17/91
Modified: Fanuc 10T MS [-] L001.80
For: Gibbs & Associates
Replaced AbsOrInc command with SetAbs, in FirstOperation, and changed MoveType$ to 'ABSOLUTE'.
This is because Fanuc controls that operate in Standard 'G' code group 'A', interpret 'G90'
as Cutting Cycle 'A', and all incremental moves are output using 'U' and 'W' addresses. All
Post Processors that fall into this category MUST BE MODIFIED!!!
All Fanuc controls that operate in Special 'G' code groups 'B' and 'C', do interpret 'G90'
to set the control into incremental mode, and therefore, any post processors that fall into
this category do not need this modification.
DWB}
{8/2/91
Modified: Fanuc 10T MS [-] L001.81
For: Gibbs & Associates
Deleted StockOff form Approach sub, it's called from all operations.
Broke up Approach sub for all operations for improved readability and less nested decisions.
Combined and modified CheckRapid subs.
Moved XOpECDC for IDExit from end of operation to NewTool, SameTool and end of Prog.
This was to ensure that all operations end at the LAST Features EndPoint.
Added LAST to XOpECDC and ZOpECPC commands at SameTool.
DWB}
{11/14/91
Modified: Fanuc 10T MS [-] L001.82
For: Gibbs & Associates
Added RestoreScale Sub per 4-Axis Post Processor.
Added Logic to suppress Feed and FeedRate for Approaches.
Modified output of Speed & ConstantSurfaceFeed for SameTool in CheckOffset sub.
Changed SetAbs to SetAbsOrInc at setup and initializations.
Added bypass of AutoFinish for Non-Canned RoughSimple Operations.
Modified AutoFinish Approach.
DWB}
{11/11/92
Copied & modified: Fanuc 10T MS [-] L001.82ż
For: AM Precision
Control: Yasnac 2000G
Machine: Mori Seiki SL-3
New Processor
Used MachSpec from Yasnac 2000GII MS SL2 L032.82
Go directly to G96 at beginning of operations, do not go to G97 at end.
SetAbs in initializations.
Misc format changes.
Changed to a no decimal point output.
Leading zeros in prep & misc codes & other commands.
Jim Radcliffe}
{10/7/93
Updated: Yas 2000G MS SL-3 [AM] L278.82
For: Gibbs & Associates/Enterprise Industries
Updated to Version 4.1 per Fanuc 10T MS [-] L001.82.1 Format.
Changed FORMAT#2 from '###.####;0.' to '###^###0'
Changed FORMAT#5 from '#^######;0.' to '#^#####0'
DWB}
{01/24/97, Updated for Catalyst v2.20 per Fanuc 10T MS [-] L001.85 Format, WS}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###^###0'
#3 = '#######0'
#4 = '###^##0'
#5 = '#^#####0'
#6 = '#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Program#,3) {.72}
FORMAT(Operation#,3) {.72}
FORMAT(Tool#,3) {.72}
FORMAT(Dwell#,4) {.72}
FORMAT(FeedIPR#,5)
FORMAT(RapidF#,6)
{Prog Subroutines **********************************************************}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
SeqLabC '( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
SeqLabC '( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
SeqLabC '( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
SeqLabC '( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
SeqLabC '( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN
PSInit: {reset flags from last Op, .70}
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN
StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN
FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN
FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN
ODApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
RETURN
IDApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL { for SameTool ApproachID }
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
RETURN
FaceApproachSP:
SeqLabC StockOnNoCan XSPC EOL { for SameTool ApproachFace }
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqLabC FeedNoCan ZSPC FeedRateNoCan EOL
END
RETURN
AppMove:
StockOff ThisOpEntryZCP
RETURN
Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqLabC StockOff ThisOpEntryXCP AppMove EOL
ODApproachSP
ELSE
IF ApproachID?
SeqLabC StockOff XOpCD AppMove EOL
IDApproachSP
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP AppMove EOL
FaceApproachSP
END
END
RETURN
CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M00' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
IF NewToolOffset?
SeqLabC LOfstOff '00' EOL
SeqLabC OpToolID LatheOffset EOL
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
ELSE
SeqLabC Preset MaxRPM EOL
SeqLabC CSSOn 'G96' Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
SeqLabC CSSOff 'G97' Speed
END
END
IF LAST ProgStop?
SeqLabC SpeedC SpinOn EOL
SeqLabC CoolOn EOL
ELSE
SeqLabC SpeedC EOL
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
DoPostScript
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC: { 4.2 }
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
CRCOnC
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN
ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
ELSE
IF CannedCycle?
SeqLab
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN
CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
RapidC
END
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
SetAbs
NegSideLathe
ReverseXZArcs
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
SeqLabC ProgID1 EOL
IF UseComments?
IF ProgramNameComment?
SeqLabC '( ' ProgramName$ ' )' EOL
END
IF ProgramComment?
SeqLabC '( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
SeqLabC '( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
SeqLabC '( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
SeqLabC '( OUTPUT IN ABSOLUTE INCHES )' EOL
END
END
RestoreScale
OpenSub
StockOff {.71.2}
SetHome
DoOpComments
DoPostScript
Plane
SeqLab Preset Home MaxRPM EOL
SeqLabC Rapid OpToolID LatheOffset CoolOn EOL
SeqLabC GearRange EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF NewTool?
{Finish off last Operation}
StockOff {.62}
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC EOL
DoEndOpPS
SeqLabC NewHome CoolOff EOL
SeqLabC LOfstOff '00' EOL
IF LAST ProgStop?
SeqLabC 'M00' EOL
ELSE
SeqLabC ProgStop EOL
END
{Start new Operation}
DoOpComments
DoPostScript
SeqLab Preset Home MaxRPM EOL
SeqLabC Rapid OpToolID LatheOffset CoolOn EOL
SeqLabC GearRange EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF SameTool? {.62}
{Start new Operation}
StockOff
DoOpComments
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
CheckOffset
ODApproachSP
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
CheckOffset
IDApproachSP
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
CheckOffset
FaceApproachSP
END
END
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
SeqLabC LCycle
IF ApproachFace?
'Z' FirstMoveEPZ# XatFinZ
ELSE
XatFinZ FinZ
END
XTapAtZ FeedRate EOL
SimpleRough
ELSE
TagInc
SetPass2
IF RoughContour?
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft CutDepth FeedRate EOL
'>' Tag# EOL
SeqLab StepMove StrtPos EOL
ELSE
IF RoughPatternShift?
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft XminusU ZminusW NumCuts FeedRate EOL
'>' Tag# EOL
SeqLab Rapid StrtPos EOL
END
END
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
SetPass1
TrackXNO# CycleStartX#
TrackZNO# CycleStartZ#
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
SeqLabC LCycle XatFinZ FinZ XTapAtZ CutMethod ThrdHeight CutDepth ThrdLead ToolAngle EOL
IF AutoFinish?
SeqLabC 'G92' XatFinZ FinZ XTapAtZ ThrdLead EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF PeckChipBreaker?
SeqLabC LCycle ZDepth RLevel Dwell Peck Retract FeedRate EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
ELSE
IF Grooving?
StockOn
SetPass1
SeqLabC StrtPos EOL
ToolPath
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish?
IF NOT Drilling? AND NOT Grooving? AND NOT RoughSimple?
StockOff
IF Turning?
SetPass1
RapidC
IF ApproachFace?
SeqLabC ZOpECPC EOL
FaceApproachSP
ELSE
SeqLabC XOpECDC EOL
IF ApproachOD?
ODApproachSP
ELSE {ApproachID}
IDApproachSP
END
END
ELSE
SetPass2
SeqLabC RapidC XSPC ZSPC EOL
END
SeqLabC StockOff StrtPosC EOL
ToolPath
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}
{End of program ************************************************************}
{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
RapidC
END
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC EOL
DoEndOpPS
SeqLabC FirstHome CoolOff EOL
SeqLabC OpToolID '00' EOL
IF ProgStop?
SeqLabC 'M00' EOL
ELSE
SeqLabC ProgStop EOL
END
SeqLabC SpinOff EOL
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
Wyszukiwarka
Podobne podstrony:
Yas 2000G MS SL4 [EI] L291 82 1Fanuc 16T MS [AM] L615 85 2Yasnac 2000G MS [BMR] L769 85Yasnac 2000G MS (ST) L106 85Yasnac LX3 MS SL 25 L277 85Fagor 8025 TG [AM] L672 85Yasnac 2000G MS [PC] L055 82Fanuc 10T MS AL2 [HS] L484 85 7Fanuc 6T MS TL5 [GHH] L693 85 2Yas MX2 MS MV35 40 M104 87Fan 16T MS SL25 [HS] L501 85 4Dynapath 10M [AM] M906 85 2Fanuc 0TB Hard [AM] L391 85 1Fanuc 15T MS SL25B[AA] L306 85Fanuc 6T MS SL4 [HS] L472 85 7Fanuc 6T MS SL6 [GHH] L694 85 2więcej podobnych podstron