Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0102 16486 002/1,3 2 DTC is set: If mass air flow signal drops WS/ER Let engine idle, watch display 002/3, must be
below 1.39 g/s for longer than 2 sec. with in the range of 3.4 to 6.5 g/s.
an engine speed under 1000 RPM.
P0103 16486 002/1,3 2 DTC is set: If mass air flow signal rises WS/ER Let engine idle, watch display 002/3, must be
above 73.3 g/s for longer than 2 sec. in the range of 3.4. to 6.5 g/s.
with an engine speed under 1000 RPM.
P0112 16496 003/4 2 DTC is set: If air intake temp. rises WS/ER Let engine idle, wait 5 sec., watch display
above 135.00C for longer than 2 sec., 5 003/4, should show reasonable values, not
sec. after engine start. 19.50C (substitute 1551 value).
P0113 16497 003/4 2 DTC is set: If air intake temp. drops WS/ER Let engine idle, wait 5 sec., watch display
below -45.00C for longer than 2 sec., 5 003/4, should show reasonable values, not
sec. after engine start. 19.50C (substitute 1551 value).
P0116 16500 003/3 2 DTC is set: If coolant temperature drops WS/ER Cool engine down to 60.0°C (003/3), start
10.00C below temperature map after engine and let idle, watch temperature, should
engine start. show reasonable values, reaching 90.0°C.
P0117 16501 003/3 2 DTC is set: If engine coolant WS/ER Let engine idle, watch display 003/3, should
temperature rises above 130.50C for show reasonable values between 85.0 to
longer than 2 sec. 105.00C with a warm engine.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0118 16502 003/3 2 DTC is set: If engine coolant WS/ER Let engine idle, watch display 003/3, should
temperature drops below -45.00C for show reasonable values between 85.0 to
longer than 2 sec. 105.00C with a warm engine.
P0121 16505 003/1,3 2 DTC is set: If throttle drive valve TD Warm up engine to 68.25°C (003/3) and drive
004/1,3 potentiometer voltage drops below with engine speed in the range of 2800RPM to
0.647V with an engine speed in the 5200RPM (003/1) and an engine load over
range of 2720RPM to 5200RPM, engine 5.90ms (004/3), watch display 004/1, must not
load over 5.90ms and an engine coolant drop below 12.9% for longer than 1 sec.
temp. over 68.25°C, for longer than 1.5
sec.
P0122 16506 004/1 2 DTC is set: If throttle valve WS/ER Let engine idle, watch display 004/1, must not
potentiometer voltage drops below show values below 2.7% , for longer than 1.5
0.137V, for longer than 1.5 sec. sec.
P0123 16507 004/1 2 DTC is set: If throttle valve WS/ER Let engine idle, watch display 004/1, must not
potentiometer voltage rises above show values above 97.2%, for longer than 1.5
4.863V, for longer than 1.5 sec. sec.
P0130 16514 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/1 (B1-S1) is in the range from 0.149V to voltage (003/2), must be greater than 8.000V,
027/1 0.400V for longer than 30 sec. or watch display 026/1, must not be in the range
if oxygen sensor voltage (B1-S1) is in from 0.149V to 0.400V for longer than 30 sec.,
the range from -0.038V to 0.040V for or
longer than 30 sec. with oxygen sensor display 026/1 must not stay in the range below
voltage (B1-S2) greater than 0.499V. 0.040V for longer than 30 sec. with oxygen
Diagnosing 150 sec. after engine start sensor voltage (B1-S2) (027/1) greater than
and a battery voltage over 8.000V. 0.499V.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0131 16515 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Erase DTC-memory, function 05, let engine
026/1 (B1-S1) drops below -0.119V for longer idle, wait 150 sec., check battery voltage
than 10 sec. 150 sec. after engine start (003/2), must be greater than 8.000V, watch
and a battery voltage over 8.000V, or 026/1, must not drop below -0.119V for longer
if oxygen sensor voltage (B1-S1) is in than 10 sec. Check DTC-memory again,
the range from 0.178V to 0.375V for function 02, should not be this fault.
longer than 0.10 sec. with cold sensors.
P0132 16516 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/1 (B1-S1) rises above 1.052V for longer voltage (003/2), must be greater than 8.000V,
than 10 sec., 150 sec. after engine start watch 026/1, must not exceed 1.052V for
and a battery voltage over 8.000V. longer than 10 sec.
P0133 16517 029/4 2 DTC is set: If the time period of heated WS/ER Let engine idle, go in basic settings, function
oxygen sensor before TWC bank 1 is 04 and choose display 029. After test end,
over 2.50 sec. display 029/4 must show B1-S1 OK.
For more information and conditions use
template 029!
P0134 16518 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/1 (B1-S1) is in the range from 0.400V to voltage (003/2), must be greater than 8.000V,
0.598V for longer than 10 sec., 150 sec. watch 026/1, must not stay in the range from
after engine start and a battery voltage 0.400V to 0.598V for longer than 10 sec.
over 8.000V.
P0136 16520 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
027/1 (B1-S2) is in the range from -0.038V to voltage (003/2), watch 027/1, must not stay in
0.040V for longer than 60 sec., 150 sec. the range from -0.038V to 0.040V for longer
after engine start and a battery voltage than 60 sec.
over 8.000V.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0137 16521 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Erase DTC-memory, function 05, let engine
027/1 (B1-S2) drops below -0.119V for 10 sec., idle, wait 150 sec., check battery voltage
150 sec. after engine start and a battery (003/2), must be greater than 8.000V, watch
voltage over 8.000V, or 027/1, must not drop below -0.119V and stay
if oxygen sensor voltage (B1-S2) is in there for longer than 10 sec. Check DTC-
the range from 0.178V to 0.375V for memory again, function 02, should not be this
longer than 0.10 sec. with cold sensors. fault.
P0138 16522 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
027/1 (B1-S2) rises above 1.052V for longer voltage (003/2), watch display 027/1, must not
than 10 sec., 150 sec. after engine start. exceed 1.052V for longer than 10 sec.
P0140 16524 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., watch display
027/1 (B1-S2) is in the range from 0.400V to 027/1, must not stay in the range from 0.400V
0.499V for longer than 400 sec., 150 to 0.499V for longer than 400 sec.
sec. after engine start.
P0150 16534 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/2 (B2-S1) is in the range from 0.149V to voltage (003/2), must be greater than 8.000V,
027/2 0.400V for longer than 30 sec. or watch display 031/1, must not be in the range
if oxygen sensor voltage (B2-S1) is in from 0.149V to 0.400V for longer than 30 sec.,
the range from -0.038V to 0.040V for or
longer than 30 sec. with oxygen sensor display 026/2 must not stay in the range below
voltage (B2-S2) greater than 0.499V. 0.040V for longer than 30 sec. with oxygen
Diagnosing 150 sec. after engine start sensor voltage (B2-S2) (027/2) greater than
and a battery voltage over 8.000V. 0.499V.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0151 16535 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Erase DTC-memory, function 05, let engine
026/2 (B2-S1) drops below -0.119V for longer idle, wait 150 sec., check battery voltage
than 10 sec. 150 sec. after engine start (003/2), must be greater than 8.000V, watch
and a battery voltage over 8.000V, or 031/1, must not drop below -0.119V for longer
if oxygen sensor voltage (B2-S1) is in than 10 sec. Check DTC-memory again,
the range from 0.178V to 0.375V for function 02, should not be this fault.
longer than 0.10 sec. with cold sensors.
P0152 16536 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/2 (B2-S1) rises above 1.052V for longer voltage (003/2), must be greater than 8.000V,
than 10 sec., 150 sec. after engine start watch 026/2, must not exceed 1.052V for
and a battery voltage over 8.000V. longer than 10 sec.
P0153 16537 030/4 2 DTC is set: If the time period of heated WS/ER Let engine idle, go in basic settings, function
oxygen sensor before TWC bank 2 is 04 and choose display 030. After test end,
over 2.50 sec. display 030/4 must show B2-S1 OK.
For more information and conditions use
template 030!
P0154 16538 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
026/2 (B2-S1) is in the range from 0.400V to voltage (003/2), must be greater than 8.000V,
0.598V for longer than 10 sec., 150 sec. watch 026/2, must not stay in the range from
after engine start and a battery voltage 0.400V to 0.598V for longer than 10 sec.
over 8.000V.
P0156 16540 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
027/2 (B2-S2) is in the range from -0.038V to voltage (003/2), must be greater than
0.040V for longer than 60 sec., 150 sec. 8.000V,watch 027/2, must not stay in the
after engine start and a battery voltage range from -0.038V to 0.040V for longer than
over 8.000V. 60 sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0157 16541 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Erase DTC-memory, function 05, let engine
027/2 (B2-S2) drops below -0.119V for 10 sec., idle, wait 150 sec., check battery voltage
150 sec. after engine start and a battery (003/2), must be greater than 8.000V, watch
voltage over 8.000V, or 027/2, must not drop below -0.119V and stay
if oxygen sensor voltage (B2-S2) is in there for longer than 10 sec. Check DTC-
the range from 0.178V to 0.375V for memory again, function 02, should not be this
longer than 0.10 sec. with cold sensors. fault.
P0158 16542 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
027/2 (B2-S2) rises above 1.052V for longer voltage (003/2), must be greater than 8.000V,
than 10 sec., 150 sec. after engine start watch display 027/2, must not exceed 1.052V
and a battery voltage over 8.000V. for longer than 10 sec.
P0160 16544 003/2 2 DTC is set: If oxygen sensor voltage WS/ER Let engine idle, wait 150 sec., check battery
027/2 (B2-S2) is in the range from 0.400V to voltage (003/2), must be greater than 8.000V,
0.499V for longer than 400 sec., 150 watch display 027/2, must not stay in the
sec. after engine start and a battery range from 0.400V to 0.499V for longer than
voltage over 8.000V. 400 sec.
P0300 16684 017/3,4 3 DTC is set: If combustion misfiring has TD Before starting repair procedure:
019/1,2,3,4 been recognized for one or more -check 017/3, 019/1,2,3,4 and 020/1,2,3,4
020/1,2,3,4 cylinders -go in basic settings, function 04 and choose
017,
017/4 must show ADP. OK
Perform TD:
check after TD 017/3, 019/1,2,3,4 and
020/1,2,3,4
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0301 16685 017/3,4 3 DTC is set: If combustion misfiring has TD Before starting repair procedure:
P0302 16686 019/1,2,3,4 been recognized for one cylinder -check 017/3, 019/1,2,3,4 and 020/1,2,3,4
P0303 16687 020/1,2,3,4 -go in basic settings, function 04 and choose
P0304 16688 017,
P0305 16689 017/4 must show ADP. OK
P0306 16690 Perform TD:
P0307 16691 check after TD 017/3, 019/1,2,3,4 and
P0308 16692 020/1,2,3,4
P0321 16705 2 DTC is set: If no mark can be found on WS/ER Start engine.
the crankshaft position disc.
P0322 16706 1 DTC is set: If no engine speed signal WS/ER Start engine.
occurs.
P0327 16711 003/1,3 1 DTC is set: If knock sensor voltage bank TD Warm up engine over 35.250C (003/3),
004/3 1 drops below 0.860V with an engine accelerate to 3000 RPM (003/1) with an engine
015/1,2,3,4 coolant temp. over 35.250C, engine load over 3.50 ms (004/3), watch display
speed over 2600 RPM and engine load 015/1,2,3,4 must not drop below 0.860V for
over 3.50 ms, for more than 100 longer than 6 sec.
consecutive combustions.
P0328 16712 003/1,3 1 DTC is set: If knock sensor voltage bank TD Warm up engine over 35.250C (003/3),
004/3 1 rises above 20.080V with an engine accelerate to 3000 RPM (003/1) with an engine
015/1,2,3,4 coolant temp. over 35.250C, engine load over 3.50 ms (004/3), watch display
speed over 2600 RPM and engine load 015/1,2,3,4 must not rise above 20.080V for
over 3.50 ms, for more than 100 longer than 6 sec.
consecutive combustions.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0332 16716 003/1,3 1 DTC is set: If knock sensor voltage bank TD Warm up engine over 35.250C (003/3),
004/3 1 drops below 0.860V with an engine accelerate to 3000 RPM (003/1) with an engine
016/1,2,3,4 coolant temp. over 35.250C, engine load over 3.50 ms (004/3), watch display
speed over 2600 RPM and engine load 016/1,2,3,4 must not drop below 0.860V for
over 3.50 ms, for more than 100 longer than 6 sec.
consecutive combustions.
P0333 16717 003/1,3 1 DTC is set: If knock sensor voltage bank TD Warm up engine over 35.250C (003/3),
004/3 1 rises above 20.080V with an engine accelerate to 3000 RPM (003/1) with an engine
016/1,2,3,4 coolant temp. over 35.250C, engine load over 3.50 ms (004/3), watch display
speed over 2600 RPM and engine load 016/1,2,3,4 must not rise above 20.080V for
over 3.50 ms, for more than 100 longer than 6 sec.
consecutive combustions.
P0422 16806 031/4 2 DTC is set: If the conversion rate of the WS/ER Let engine idle, go in basic settings, function
Cat B1 is too low. 04 and choose display 031. After test end,
display 031/4 must show Cat B1 O.K.
For more information and conditions use
template 031!
P0432 16816 032/4 2 DTC is set: If the conversion rate of the WS/ER Let engine idle, go in basic settings, function
Cat B2 is too low. 04 and choose display 032. After test end,
display 032/4 must show Cat B2 O.K.
For more information and conditions use
template 032!
P0441 16825 033/4 OFF DTC is set: If EVAP system has WS/ER Let engine idle, go in basic settings, function
incorrect air flow. 04 and choose display 033. After test end,
display 033/4 must show EVAP OK.
For more information and conditions use
template 033!
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0442 16826 034/4 OFF DTC is set: If fuel tank system has a WS/ER Let engine idle, go in basic settings, function
small leak. 04 and choose display 034. After test end,
display 034/4 must show Syst. OK.
For more information and conditions use
template 034!
P0455 16826 034/4 OFF DTC is set: If fuel tank system has a WS/ER Let engine idle, go in basic settings, function
large leak. 04 and choose display 034. After test end,
display 034/4 must show Syst. OK.
For more information and conditions use
template 034!
P501 16885 008/4 2 DTC is set: If vehicle speed drops below TD Have a short test drive, watch display (008/4),
3.8km/h with an engine coolant must show reasonable vehicle speed
temperature over 39.750C, an engine corresponding to the odometer (must not drop
speed between 1400 RPM and 5000 to 0 km/h while driving).
RPM and a decel for longer than 2.5 sec.
P0560 16944 2 DTC is set: If the system voltage of the WS/IO Erase DTC-memory, function 05, after 1 sec.,
ECM has a malfunction. check DTC-memory again, function 02, should
not be this fault.
P0662 16946 2 DTC is set: If the system voltage of the WS/IO Erase DTC-memory, function 05, after 1 sec.,
ECM is too low. check DTC-memory again, function 02, should
not be this fault.
P0563 16047 2 DTC is set: If the system voltage of the WS/IO Erase DTC-memory, function 05, after 1 sec.,
ECM is too high. check DTC-memory again, function 02, should
not be this fault.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P0601 16985 2 DTC is set: If check sum error of internal WS/ER Erase DTC-memory, function 05, let engine
control module memory occurs. idle. After 10 sec., check DTC-memory again,
function 02, should not be this fault.
P0604 16988 2 DTC is set: If Ram error of internal WS/ER Erase DTC-memory, function 05, let engine
control module memory occurs. idle. After 2 sec., check DTC-memory again,
function 02, should not be this fault.
P1102 17510 028/1,3 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B1-S1) drops below 2.5 &! with a status is ON (028/3), let engine idle, watch
heater status ON, for longer than 30 display 028/1, must not drop below 2.4 &! for
sec., 180 sec after engine start. longer than 10 sec.
P1105 17513 028/2,4 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B1-S2) drops below 2.5 &! with a status is ON (028/4), let engine idle, watch
heater status ON, for longer than 30 display 028/2, must not drop below 2.4 &! for
sec., 180 sec after engine start. longer than 10 sec.
P1107 17515 028/1,3 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B2-S1) drops below 2.5 &! with a status is ON (028/3), let engine idle, watch
heater status ON, for longer than 30 display 028/1, must not drop below 2.4 &! for
sec., 180 sec after engine start. longer than 10 sec.
P1110 17518 028/2,4 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B2-S2) drops below 2.5 &! with a status is ON (028/4), let engine idle, watch
heater status ON, for longer than 30 display 028/2, must not drop below 2.4 &! for
sec., 180 sec after engine start. longer than 10 sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1127 17535 003/3 2 DTC is set: If oxygen sensor learning TD Warm up engine to 80.250C (003/3), drive on
010/3 value at partial load bank 1 drops below - the Freeway with a speed of 65MPH, using
22.7%. cruise control. Watch 010/3, must not begin to
fall to -10.0% after 10 min of driving.
P1128 17536 003/3 2 DTC is set: If oxygen sensor learning TD Warm up engine to 80.250C (003/3), drive on
010/3 value at partial load bank 1 rises above the Freeway with a speed of 65MPH, using
22.7%. cruise control. Watch 010/3, must not begin to
rise to 10.0% after 10 min of driving.
P1129 17537 003/3 2 DTC is set: If oxygen sensor learning TD Warm up engine to 80.250C (003/3), drive on
010/4 value at partial load bank 2 drops below - the Freeway with a speed of 65MPH, using
22.7%. cruise control. Watch 010/4, must not begin to
fall to -10.0% after 10 min of driving.
P1130 17538 003/3 2 DTC is set: If oxygen sensor learning TD Warm up engine to 80.250C (003/3), drive on
010/4 value at partial load bank 2 rises above the Freeway with a speed of 65MPH, using
22.7%. cruise control. Watch 010/4, must not begin to
rise to 10.0% after 10 min of driving.
P1136 17544 003/3 2 DTC is set: If oxygen sensor learning WS/ER Warm up engine to 80.250C (003/3), let engine
010/1 value at idle bank 1 rises above 17.4%. idle. Watch 010/1, must not begin to rise to
9.0% after 5 min of idle.
P1137 17545 003/3 2 DTC is set: If oxygen sensor learning WS/ER Warm up engine to 80.250C (003/3), let engine
010/1 value at idle bank 1 drops below -17.4%. idle. Watch 010/1, must not begin to fall to
-14.0% after 5 min of idle.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1138 17546 003/3 2 DTC is set: If oxygen sensor learning WS/ER Warm up engine to 80.250C (003/3), let engine
010/2 value at idle bank 2 rises above 17.4%. idle. Watch 010/2, must not begin to rise to
9.0% after 5 min of idle.
P1139 17547 003/3 2 DTC is set: If oxygen sensor learning WS/ER Warm up engine to 80.250C (003/3), let engine
010/2 value at idle bank 2 drops below -17.4%. idle. Watch 010/2, must not begin to fall to
-14.0% after 5 min of idle.
P1141 17549 003/1 2 DTC is set: If altitude level is not in the TD Erase DTC-memory, function 05, drive with a
004/1 range from -50.0% to 20.0%. speed over 20.5 km/h (008/4), open throttle
008/4 shortly to an angle in the range of 150 to 500
(004/1) with an engine speed over 2000RPM
(003/1) for longer than 10 sec., check DTC-
memory again, function 02, should not be this
fault.
P1176 17584 025 OFF DTC is set: If O2S correction control WS/ER Erase DTC-memory, function 05, let engine
036/3 behind TWC bank 1 is out of the range. idle, go in basic settings, function 04 and
choose display 025 after test end, display
036/3 bit 6 must be 0, check DTC-memory
again, function 02, should not be this fault.
For more information and conditions use
template 025!
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1177 17585 025 OFF DTC is set: If O2S correction control WS/ER Erase DTC-memory, function 05, let engine
036/4 behind TWC bank 2 is out of the range. idle, go in basic settings, function 04 and
choose display 025 after test end, display
036/4 bit 6 must be 0, check DTC-memory
again, function 02, should not be this fault.
For more information and conditions use
template 025!
P1196 17604 028/1,3 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B1-S1) rises above 9.2 &! with a status is ON (028/3), let engine idle, watch
heater status ON, for longer than 30 display 028/1, must not rise above 9.2 &! for
sec., 180 sec after engine start. longer than 30 sec.
P1197 17605 028/2,4 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B1-S2) rises above 9.2 &! with a status is ON (028/4), let engine idle, watch
heater status ON, for longer than 30 display 028/2, must not rise above 9.2 &! for
sec., 180 sec after engine start longer than 30 sec.
P1198 17606 028/1,3 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B2-S1) rises above 9.2 &! with a status is ON (028/3), let engine idle, watch
heater status ON, for longer than 30 display 028/1, must not rise above 9.2 &! for
sec., 180 sec after engine start. longer than 30 sec.
P1199 17607 028/2,4 2 DTC is set: If resistance of O2S sensor WS/ER Wait 180 sec after engine start and until heater
heater (B2-S2) rises above 9.2 &! with a status is ON (028/4), let engine idle, watch
heater status ON, for longer than 30 display 028/2, must not rise above 9.2 &! for
sec., 180 sec after engine start. longer than 30 sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1201 17609 1 DTC is set: If cyl. 1 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1202 17610 1 DTC is set: If cyl. 2 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1203 17611 1 DTC is set: If cyl. 3 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1204 17612 1 DTC is set: If cyl. 4 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1205 17613 1 DTC is set: If cyl. 5 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1206 17614 1 DTC is set: If cyl. 6 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1207 17615 1 DTC is set: If cyl. 7 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
P1208 17616 1 DTC is set: If cyl. 8 fuel injector has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction in the circuit for idle, check DTC-memory again, function 02,
more than 0.5 sec. should not be this fault.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1213 17621 1 DTC is set: If cyl. 1 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1214 17622 1 DTC is set: If cyl. 2 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1215 17623 1 DTC is set: If cyl. 3 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1216 17624 1 DTC is set: If cyl. 4 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1217 17625 1 DTC is set: If cyl. 5 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1218 17626 1 DTC is set: If cyl. 6 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1219 17627 1 DTC is set: If cyl. 7 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1220 17628 1 DTC is set: If cyl. 8 fuel injector is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for more than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1250 17658 OFF DTC is set: If fuel tank level is too low WS/IO Erase DTC-memory, function 05, switch
with a present misfiring fault . ignition on, check DTC-memory again,
function 02, should not be this fault.
P1280 17688 035/4 2 DTC is set: If the air shrouded fuel WS/ER Let engine idle, go in basic settings, function
injectors have too low air flow. 04 and choose display 035 after test end,
display 035/4 must show A-IV OK.
For more information and conditions use
template 035!
P1283 17691 2 DTC is set: If air shrouded fuel injector WS/ER Erase DTC-memory, function 05, let engine
valve has an electrical malfunction in the idle, check DTC-memory again, function 02,
circuit for more than 0.5 sec. should not be this fault.
P1286 17694 035 2 DTC is set: If air shrouded fuel injector WS/ER Erase DTC-memory, function 05, let engine
valve is short to B+ for more than 0.5 idle, go in basic settings, function 04 and
sec. choose display 035, check DTC-memory
again, function 02, should not be this fault.
P1325 17733 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
013/1 correction cyl.1 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 013/1, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
P1326 17734 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
013/2 correction cyl.2 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 013/2, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1327 17735 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
013/3 correction cyl.3 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 013/3, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
P1328 17736 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
013/4 correction cyl.4 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than and 3rd gear, watch display 013/4, must not
800RPM, for 20 consecutive rise over 15.00KW, for longer than 1 sec.
combustion.
P1329 17737 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
014/1 correction cyl.5 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 014/1, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
P1330 17738 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
014/2 correction cyl.6 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 014/2, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
P1331 17739 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
014/3 correction cyl.7 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 014/3, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
P1332 17740 003/3 OFF DTC is set: If knock sensor timing TD Warm up engine to 80.250C (003/3), go up a
014/4 correction cyl.8 rises above 15.00 KW hill, accelerate with kick down in the 1st, 2nd
with an engine speed greater than 800 and 3rd gear, watch display 014/4, must not
RPM, for 20 consecutive combustion. rise over 15.00KW, for longer than 1 sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1386 17794 003/3 OFF DTC is set: If a knock sensor control WS/ER Warm up engine to 35.250C (003/3), erase
circuit error occurs in the ECM with an DTC-memory, function 05, let engine idle,
engine coolant temp. over 35.250C. check DTC-memory again, function 02, should
not be this fault.
P1391 17799 2 DTC is set: If camshaft position sensor WS/ER Erase DTC-memory, function 05, let engine
bank 2 is short to ground for more than 2 idle, check DTC-memory again, function 02,
sec. should not be this fault.
P1392 17800 2 DTC is set: If camshaft position sensor WS/ER Erase DTC-memory, function 05, let engine
bank 2 has an open circuit/is short to B+ idle, check DTC-memory again, function 02,
for more than 2 sec. should not be this fault.
P1409 17817 2 DTC is set: If fuel tank ventilation valve WS/ER Erase DTC-memory, function 05, let engine
has an electrical malfunction for longer idle, check DTC-memory again, function 02,
than 0.5 sec. should not be this fault.
P1410 17818 033 2 DTC is set: If fuel tank ventilation valve WS/ER Erase DTC-memory, function 05, let engine
is short to B+ for longer than 0.5 sec. idle, go in basic settings, function 04, choose
display 033, after test end, check DTC-
memory again, function 02, should not be this
fault.
P1470 17878 2 DTC is set: If leak detection pump has WS/ER Erase DTC-memory, function 05, let engine
an electrical malfunction for longer than idle, check DTC-memory again, function 02,
0.5 sec. should not be this fault.
P1471 17879 034 2 DTC is set: If leak detection pump is WS/ER Erase DTC-memory, function 05, let engine
short to B+ for longer than 0.5 sec. idle, go in basic settings, function 04, choose
display 034, after test end, check DTC-
memory again, function 02, should not be this
fault.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1475 17883 034 2 DTC is set: If leak detection pump has a WS/ER Erase DTC-memory, function 05, let engine
mechanical malfunction or no signal idle, go in basic settings, function 04, choose
display 034, after test end, check DTC-
memory again, function 02, should not be this
fault.
P1476 17884 034 2 DTC is set: If leak detection pump has WS/ER Erase DTC-memory, function 05, let engine
insufficient vacuum. idle, go in basic settings, function 04, choose
display 034, after test end, check DTC-
memory again, function 02, should not be this
fault.
P1500 17908 OFF DTC is set: If fuel pump relay circuit has WS/ER Erase DTC-memory, function 05, let engine
an electrical malfunction for longer than idle, check DTC-memory again, function 02,
0.5 sec. should not be this fault.
P1502 17910 OFF DTC is set: If fuel pump relay circuit is WS/ER Erase DTC-memory, function 05, let engine
short to B+ for longer than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1505 17913 004/4 2 DTC is set: If idle position switch does WS/ER Let engine idle, accelerate engine and close
not close until 600 sec. after engine throttle, watch display 004/4 must switch
start, time only counting while vehicle between idle, part throttle and idle again.
speed under 100km/h, engine speed
below 1800RPM, engine load below
5.00ms and throttle angle below 3.90.
P1506 17914 2 DTC is set: If idle position switch is WS/ER Erase DTC-memory, function 05, let engine
closed and the throttle position voltage is idle, accelerate engine and close throttle very
below learned value for most open quickly, check DTC-memory again, function
throttle drive position for longer than 2.2 02, should not be this fault.
sec.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1507 17915 007/4 2 DTC is set: If idle system learned value WS/ER Let engine idle, wait 2 min., watch display
rises over 130 for longer than 102 sec. at 007/4, must stay in the range of 75 to 100.
an engine over 900C.
P1508 17916 007/4 2 DTC is set: If idle system learned value WS/ER Let engine idle, wait 2 min., watch display
drops below 55 for longer than 102 sec. 007/4, must stay in the range of 75 to 100.
at an engine over 900C.
P1509 17917 2 DTC is set: If idle air control circuit has WS/ER Erase DTC-memory, function 05, let engine
an electrical malfunction for longer than idle, check DTC-memory again, function 02,
0.5 sec. should not be this fault.
P1510 17918 2 DTC is set: If idle air control circuit is WS/ER Erase DTC-memory, function 05, let engine
short to B+ for longer than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1511 17919 OFF DTC is set: If intake manifold change WS/ER Erase DTC-memory, function 05, let engine
over valve circuit has an electrical idle, check DTC-memory again, function 02,
malfunction for longer than 0.5 sec. should not be this fault.
P1512 17920 022/1,4 OFF DTC is set: If intake manifold change WS/ER Erase DTC-memory, function 05, let engine
over valve is short to B+ with an status idle, accelerate engine over 3800RPM (022/1)
SU-V ON for longer than 0.5 sec. for 3 sec, watch display 022/4, must change
to SU-V ON, check DTC-memory again,
function 02, should not be this fault.
P1517 17925 1 DTC is set: If main relay circuit has an WS/ER Erase DTC-memory, function 05, let engine
electrical malfunction for longer than 0.5 idle, check DTC-memory again, function 02,
sec. should not be this fault.
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1518 17926 1 DTC is set: If main relay circuit is short WS/ER Erase DTC-memory, function 05, let engine
to B+ for longer than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1560 17968 003/1 OFF DTC is set: If engine speed rises above WS/ER Let engine idle. Be careful! Accelerate engine
6800RPM. for a short time, watch display 003/1, must not
reach 6800RPM.
P1602 18010 OFF DTC is set: If power supply terminal 30 WS/ER Erase DTC-memory, function 05, let engine
has low voltage. idle, check DTC-memory again, function 02,
should not be this fault.
P1606 18014 OFF DTC is set: If the rough road or required WS/ER Erase DTC-memory, function 05, let engine
engine torque information from the ABS- idle, check DTC-memory again, function 02,
ECU has an electrical malfunction with a should not be this fault.
present misfire recognition.
P1612 18020 1/OFF DTC is set: ECM is coded incorrect. WS/ER Erase DTC-memory, function 05, let engine
idle, check DTC-memory again, function 02,
should not be this fault.
P1624 18032 1 DTC is set: If MIL request signal is WS/ER Erase DTC-memory, function 05, let engine
active. idle, check DTC-memory again, function 02,
should not be this fault.
P1625 18033 2 DTC is set: If CAN Bus error message WS/ER Erase DTC-memory, function 05, let engine
occurs from the TCM. idle, check DTC-memory again, function 02,
should not be this fault.]
Output on GST For troubleshooting MIL DTC description Test After repair quality check
and/or use on VAG status for condition
on VAG 1551/1552 1551/1552 MIL ON
scan tool display group / field
P1640 18048 2 DTC is set: If an internal control module WS/ER Erase DTC-memory, function 05, let engine
EPROM error occurs. idle for 5 sec., check DTC-memory again,
function 02, should not be this fault.
P1690 18098 OFF DTC is set: MIL circuit has an electrical WS/ER Erase DTC-memory, function 05, let engine
malfunction for longer than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1693 18101 OFF DTC is set: MIL circuit is short to B+ for WS/ER Erase DTC-memory, function 05, let engine
longer than 0.5 sec. idle, check DTC-memory again, function 02,
should not be this fault.
P1851 18259 OFF DTC is set: If CAN Bus missing WS/ER Erase DTC-memory, function 05, let engine
message from the ABS control unit. idle, check DTC-memory again, function 02,
should not be this fault.
Wyszukiwarka
Podobne podstrony:
Audi Dealer Codes ObdVolkswagen Audi Colour CodesAudi,Skoda, Seat, VW, gniazdo diagnost , diagnostyka pojBentleyPublishers com Audi? OBD DiagnosticsChrysler Computer Codes 2001 For DiagnosticDiagnostykaAUTO TRANS DIAGNOSIS AG4Debugowanie NET Zaawansowane techniki diagnostyczne?bnet[Audi A4 8E ] Zestaw naprawczy do luzujacej sie rolety w Avancie B6 i B7AUDI TT 8J 06plDiagnostyka OBD EOBD OBD2 Opis VAG COMwięcej podobnych podstron