SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
X
MAKE
SAAB
MOD.
9.3
YEAR
98 âÄ…Ĺ‚ PETROL
DIESEL
ALARM/SIREN
Position the compact alarms and the sirens in the space between the battery and the wing.
POSITION
To pass the cables use the original rubber sleeve located near the support of the shock absorber, passenger’s side.
POWER SUPPLY
+ 30: connect to the 4 mm2 RED wire located in the wiring harness coming out of the black multiway connector in the fuse box.
- 31: connect with a terminal to an original power supply located behind the left lateral bulkhead, driver’s side.
IGNITION WIRE
+ 15/54: connect to the 1,5 mm2 BLACK/GREEN wire located in the wiring harness coming out of the grey connector behind the left lateral bulkhead, driver’s side.
DIRECTION INDICATORS
Connect to the 1,5 mm2 GREEN/BLACK and GREY/BLACK wires located in the wiring harness coming out of the 4th connector starting from the bottom, behind the left lateral bulkhead, driver’s side.
ELECTRIC WINDOWS
Positive control signal
Front window, driver’s side: cut the BLACK/WHITE wire located at the position nr.19.
Front window, passenger’s side: cut the LIGHT BLUE/ WHITE wire located at the position nr.17.
Rear window, passenger’s side: cut the GREEN/RED wire located at the position nr.14.
Rear window, passenger’s side: cut the LIGHT BLUE/GREEN wire located at the position nr.2.
These connections are made directly on the coming out of the respective original switches located in the central tunnel.
CENTRAL DOORS LOCKING
Negative control signal
Connect to the LIGHT BLUE/BROWN wire at the position nr.8 (unlock) and RED/VIOLET wire at the position nr.58 (lock) located in the wiring harness coming out of the connector of the doors central unit under the front seat, driver’s side.
IMMOBILISATION POINT
Fuel pump
Cut the YELLOW/GREY wire at the position nr.16 of the connector located under the driver’s seat.
STARTER
+50: Cut the YELLOW wire in the wiring harness coming out of the grey relè located on the relè holder plate under the dashboard, driver’s side.
BONNET SWITCH
Install an additional switch on the headlamp support plate, near the original rubber trim of the bonnet, driver’s side.
DOORS SWITCH
Connect to the following wires using 4 diodes to separate the lines: GREY/GREEN at the position nr.61, BLACK/GREEN at the position nr.12, BLACK/GREEN at the position nr.60 and BLACK/GREEN located in the central line between the two GREEN/BLACK wires in the wiring harness coming out of the connector of the doors central unit under the driver’s seat.
BOOT SWITCH
Connect to the BLACK wire located near the GREEN/BLACK wire in the wiring harness coming out of the connector of the central unit under the driver’s seat.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed sa9.398gbb.doc
as per the instructions given on the product installation manual.
Wyszukiwarka
Podobne podstrony:
AC11XXGB id 2226069 NieznanyCISAX01GBD id 2064757 NieznanySGH 2200 id 2230801 Nieznany111003105109 stress id 2048457 NieznanyCIXS201GBD id 2064760 NieznanyTOCEL96GBB id 2491297 Nieznany1078 2 FEA209544 128UEN A id 22 NieznanyMcRib(r) Sandwich id 2201097 NieznanyBD V600 L3 C A3 V1[1] 1 id 2157 NieznanyDOC0534 id 2032985 Nieznany8 17 id 2009842 NieznanyREKAN02GBBT id 2491218 Nieznanycialo albatros id 2035175 Nieznany[17] FR540NT010 id 2085454 NieznanyRO7503GBDT id 2491245 NieznanyVOLUP98GBD id 2134841 Nieznanycienie w raju rebis id 2036016 Nieznanywięcej podobnych podstron