http://www.rexresearch.com/roschin2/roschgod.htm
V. V. ROSCHIN & S. M. GODIN
Searl Effect Generator
New Energy Technologies, Vol. 2, pp. 242-245
Testing of Small Prototype to Investigate Searl's Effect
S. M. Godin and V.V. Roschin
The authors go further in the research of possibility to receive free energy by means of
rotating constant magnets (Searl s Effect).
The aim of generator compact model (GCM) testing was studying of possibility to produce a
small and maximum cheap model, which uses the ceramic magnets. Laboratory research of
this model of generator was aimed at the discovery of self-generation effects and effects of
weight change, which were already achieved on the full-size generator [1].
A general view of GCM is shown in Figure 1. The generator represented a mechanical system
consisting of general construction as a cylinder made of stainless steel divided by it height in
approximately two equal parts. The direct current motor with collector was situated in the
lower part; windings of stator and rotor were connected in series.
Figure 1
In the upper part of the construction on the axis of motor the rotor is situated as a cylindrical
ceramic magnet with a central hole made on the base of cobalt-samarium mix. The magnet is
magnetized vertically and inserted into the steel fixture, which preserves the magnet from
destruction during the quick rotation. Small magnetic rollers also made of ceramic magnets
and magnetized along the axis of rotation were placed around the rotor. All 12 rollers were
placed into the aluminum cylinders, which preserve their brittle ceramics from mechanical
impact during the work in emergency conditions. The main idea of such construction consists
in the fact that in initial state the rollers were attracted by the magnet of rotor to the side face.
Due to the repulsion of the rollers from each other, the distance between them appeared
automatically. With this distance they uniformly distributed along the entire perimeter of the
rotor. During acceleration of the rotor the rollers diverge from the rotor step by step and begin
to run in the outside cylindrical fixture, which is placed around the rotor at the distance of 1.5
mm from the external surface of rollers in the initial states. The height of the rotor magnet is
24 mm, the diameter of the inside hole is 40 mm. All other geometrical sizes and ratios are
given in Figure 2.
Figure 2
It was supposed that with a certain acceleration of rotation the rollers would begin to rotate
inside the outside fixture with self-acceleration and would carry metal surface of rotor device.
This mode will be easy to discover due to the possible decrease of the current consumed by
the electric motor. Thus, the aim of GCM testing was an attempt to find the features of energy
transformation of environment which lies in the self-acceleration of the rotor device or other
characteristic effects concentric magnetic walls around the device and fall of temperature)
discovered already. The program of device testing included registration of dependence of
rotational speed of the rollers along the outside fixture from rotation speed of the motor.
Appearance of GCM is shown in Figure 3, when this device is ready to test in laboratory
conditions. GCM was placed on the massive grounded steel plate. The power supply made in
the form of controlled transformer, isolating transformer, bridge diode rectifier and capacitive
filter were placed on the right. Besides, the generator of reference frequency G3-112 and
frequency meter C3-54 were placed here.
Figure 3
The 2-channel oscilloscope C1-99, digital combined unit TSH300 applied for the
measurement of consumption current and power supply TEC-88 (0-30 V, 0-2.5 A) applied for
power supply of the optoelectronic sensor of device rotation were placed on the left. The
measurement of rotation speed of the rollers was made with an induction-type sensor, which
was placed at the height of the rollers, on the reverse side of the aluminum fixture. The rollers
after they separated from the rotor, rolled along this fixture. During the passing of every roller
by the induction-type sensor, the impulse of voltage with the amplitude of about 1V was
produced. This voltage was supplied to one of the inputs of 2-channel oscilloscope for direct
observation on the screen. A signal from the reference generator connected with the frequency
meter was supplied to the second input of the oscilloscope.
Synchronization of scanning of the oscilloscope was provided from the same reference signal.
The frequency of the signal on the reference generator was set to provide the most stable
immovable pattern on both channels of the oscilloscope. An accurate measurement was made
according to the data from the frequency meter. Such method of measurement was chosen
because the applied collector motor of direct current ad permanent deviations of rotation rate
due to the change of voltage in the mains, heating of bearings, collector and other reasons. All
this hampered the reception of an accurate value of average rotation rate directly from the
readings of the frequency meter. It was necessary to divide the readings of frequency meter by
12 to receive the real value of rotation rate in rates per second (rate of running around the
fixture) of the rollers.
Measurement of rotation rate of the rotor was made in an analogous way, but as a sensor we
used the self-made sensor on the base of optic pair IR emitter-receiver with an open optic
channel. The sensor was assembled on the textolite baseplate and attached to the upper
plexiglass head of GCM by means of usual plasticine. Using this sensor we could quickly and
effectively adjust the necessary operating gap between the surface of optoelectronic couple
and surface of special metal disk with 25 dark and 25 light sectors applied on it. Thus, during
one rotation period of the rotor the photon-coupled sensor gave 25 impulses of voltage, which
were transferred to the oscilloscope for immediate observation. The appearance of photon-
coupled sensor or rotations attached to the upper plexiglass head of the GCM unit is shown in
Figure 4.
Figure 4
In Figure 5 you can see the oscillograms of signal from the photon-coupled sensor of rotation
(upper beam) and harmonic signal from the reference generator in the moment of coincidence
of frequencies with a one-phase accuracy. The real rotation rate of the rotor was determined
as a measured frequency (rate) of generator divided by 25 (number of dark and light sectors
on the disk of rate controller).
Figure 5
To receive reliable information on the characteristics of the electromechanical system motor-
permanent magnet of the rotor there were made several bare measurements without
installation of the rollers. Measurements were made with the placing of magnet north up and
vice versa.
As we can see from the diagrams of dependence of the motor consumption current from the
applied voltage of power supply, the strength of consumption current increases with the
voltage of power supply and reaches its maximum at 0.31 A with the minimal possible
rotation rate of the rotor. The strength of consumption current does not depend on the polarity
of installation of the magnet in the limits of experimental accuracy. For the given motor there
is an area of minimal consumption current, which lies in the diapason from 40 to 80 W.
We got similar curves of rotation speed for the cases of different location of magnets of the
rotor, which means the independence of rotation speed from the polarity of the magnet of the
rotor.
The results of measurements of rotation speeds of the rotor and rollers (given separately) are
presented in Table 1.
Table 1
Here, as in the previous example, two cases are considered. They are the case, when the
magnet was installed with its north pole up and an opposite case. The poles of the rollers
change accordingly. We should note that with the slow change of power supply voltage, we
practically always observed the instability of the trajectories of the rollers and their tailing
from the operating surface, which led to the adhesion of one or some pairs of the rollers
together.
This fact distorted the pattern of measurements, and we had to introduce correction factors
during the calculation of rotation speed of the rollers. These factors depend on the number of
fallen down or adhered rollers in pairs. This table was made taking into account these
correction factors and it is an average one according to the results of five tests. As we can see
from the table, no self-acceleration of the rollers was found. After the speed reaches a
particular value of 8.5 rps, the speed of the rollers stabilizes and does not increase in spite of
the increase of rotation speed of the rotor magnet.
Also we can see from Table 1 that the rollers always have a tendency to retard and after the
full separation with the voltage of 20-23 V.
Concerning the polarity of magnet location we can say that it does not influence the rotation
speed of the rotor and rollers in the limits of miscalculation in determination of speed and
voltage in the given experiment. Some differences in speed are defined only by mechanical
characteristics of the rollers and surface o the fixture, which was used for revolving around.
We should say that the outside surfaces of the rollers and the surface wer made of the same
material (aluminum); that s why they have a tendency of attrition even during one experiment
(10 minutes). Due to this reason we couldn t get full reiteration, but the accuracy was
sufficient to establish the fact of full absence of the self-acceleration effects and some
differences between polarities of installation of the rotor magnet and rollers.
Unfortunately, we couldn t find any anomalies in the temperature distribution and distribution
of magnetic field around the converter. Magnetic and heat walls discovered in experiments
with a big converter were almost absent around the small device.
Conclusion
These experiments proved the point of view that during the device operation the nonlinearity
of the wave processes, which take place in quantum medium (ether) plays the main role. It is
evident that there is some critical value of parameters in the magnetic system of the converter
(mass, induction of magnetic field) and only in the case of excess of these parameters the
appearance of abovementioned effects is possible.
References
1 V. Roschin, S. Godin: An Experimental Investigation of Physical Effects in a Dynamic
Magnetic System; New Energy Technologies, Vol. 1, July-August 2001, pp. 3-5.
Editor s Note: -- Alexander Frolov --- I have to say about my personal opinion of this
experimental work. It is a very strange project. I am not sure if these are 100% true
experimental results due to absence of real prototype at the present time (Only the description
of 7 KWt system was published, It was built in 1002, according to S, Godin). On the other
hand, the theory of this energy converter and its description by Godin and Roschin is in good
correlation with other theories on inner structure of physical vacuum. Faraday Lab Ltd will
develop this research direction and we hope to present our own experimental results in the
future.
Wyszukiwarka
Podobne podstrony:
Static Analysis of Binary Code to Isolate Malicious BehaviorsDynamic Performance of a Microturbine Connected to a Low Voltage NetworkMicrobiological Testing of Endoscopes Efficacy of SamplingK Ericsson, The Earliest Conversion of the Rus to ChristianityLack of Limits View to the shoreApplications of linear algebra to differential equation [sharethefiles com]V ROSCHIN & S GODIN Doświadczalne badania nieliniowych efektów w dynamicznym układzie magnetycznymLacy Collison Morley The Power of the Dead to Return to EarthUse of Diammonium Phosphate to Reduce Heavy Metal solubilityEssentials of Sociology A Down to Earth Approach aM16 HENS 7052 EPIStructure of the Forkhead Domain of FOXP2 Bound to DNADan09 The Power of a Life Dedicated to God (Dan 10)The contribution of farm animals to human healthThe Five Stages Of Small Business GrowthMcgraw Hill Handbook Of Small Electric Motors 2001 (Toc)Return of Zen Upgrades to the Single Stage, Single Ended, Class A Mosfet AmplifierA review of molecular techniques to type C glabrata isolatesEssentials of Sociology A Down to Earth Approach aZ04 HENS 7052 NIwięcej podobnych podstron