CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
IEWB-RS Lab 19
Difficulty Rating (10 highest): 10
Lab Overview:
The following scenario is a practice lab exam designed to test your skills at
configuring Cisco networking devices. Specifically, this scenario is designed to
assist you in your preparation for Cisco Systems CCIE Routing and Switching
Lab exam. However, remember that in addition to being designed as a
simulation of the actual CCIE lab exam, this practice lab should be used as a
learning tool. Instead of rushing through the lab in order to complete all the
configuration steps, take the time to research the networking technology in
question and gain a deeper understanding of the principles behind its operation.
Lab Instructions:
Prior to starting, ensure that the initial configuration scripts for this lab have been
applied. For a current copy of these scripts, see the Internetwork Expert
members site at http://members.internetworkexpert.com
Refer to the attached diagrams for interface and protocol assignments. Any
reference to X in an IP address refers to your rack number, while any reference
to Y in an IP address refers to your router number.
Upon completion, all devices should have full IP reachability to all networks in the
routing domain, including any networks generated by the backbone routers
unless explicitly specified.
Lab Do s and Don ts:
" Do not change or add any IP addresses from the initial configuration
unless otherwise specified
" Do not change any interface encapsulations unless otherwise specified
" Do not change the console, AUX, and VTY passwords or access methods
unless otherwise specified
" Do not use any static routes, default routes, default networks, or policy
routing unless otherwise specified
" Save your configurations often
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 349 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
Grading:
This practice lab consists of various sections totaling 100 points. A score of 80
points is required to achieve a passing score. A section must work 100% with the
requirements given in order to be awarded the points for that section. No partial
credit is awarded. If a section has multiple possible solutions, choose the solution
that best meets the requirements.
Grading for this practice lab is available when configured on Internetwork
Expert s racks, or the racks of Internetwork Expert s preferred vendors. See
Internetwork Expert s homepage at http://www.internetworkexpert.com for more
information.
Point Values:
The point values for each section are as follows:
Section Point Value
Bridging & Switching 12
Frame Relay 6
HDLC/PPP 3
Interior Gateway Routing 16
Exterior Gateway Routing 21
IP Multicast 9
IPv6 6
QoS 6
Security 5
System Management 6
IP Services 10
GOOD LUCK!
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 350 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
1. Bridging & Switching
1.1. VLAN Assignments
" Configure the VTP domain CCIE between SW1, SW2, SW3, and SW4.
" Create the following VLANs:
VLAN Name
127 A
4 B
5 C
7 SW1_A
8 D
10 RSPAN
32 BB2
33 BB3
44 F
77 SW1_B
88 G
568 I
" Assign the above VLANs per the diagram using the command macro
apply ACCESSPORT $VLAN X, where X is the VLAN number to
configure the VLAN assignments on all interfaces; This command should
also set the administrative mode of the interface to static access and
disable the spanning-tree forwarding delay.
3 Points
1.2. Trunking
" Configure ISL trunk links between SW1 & SW4, SW2 & SW4, and SW3 &
SW4.
" Use the lowest numbered interfaces to accomplish this.
" SW4 should initiate negotiation of these links and SW1, SW2, and SW3
should respond.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 351 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
1.3. Channeling
" Configure EtherChannel links between SW1 & SW2 and SW2 & SW3
using all available links.
" These links should use a 4-byte trunking encapsulation.
" Traffic leaving these links on SW2 should be load balanced based on the
destination IPv4 address.
3 Points
1.4. RSPAN
" Users in VLAN 127 have been reporting slow network response time,
however your administrators have not been able to track down the
problem. In order to collect more information your NOC engineers have
requested that you redirect all traffic received in VLAN 127 to a host
running Ethereal in your network.
" This host is attached to port Fa0/10 of SW3.
" Use VLAN 10 for transporting this traffic.
3 Points
2. Frame Relay
2.1. Hub-and-Spoke
" Using only physical interfaces configure a Frame Relay hub-and-spoke
network between R1, R2, and R3 with R3 as the hub.
" Traffic from R1 destined for R2 should transit R3, and vice versa.
" Use only the DLCIs specified in the diagram.
" Do not use any dynamic layer 3 to layer 2 mappings over these Frame
Relay connections.
" Do not send any redundant broadcast traffic from the spokes to the hub.
2 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 352 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
2.2. Hub-and-Spoke
" Using only physical interfaces configure a Frame Relay hub-and-spoke
network between R3, R4, and R5 with R5 as the hub.
" Use only the DLCIs specified in the diagram.
" Do not use any dynamic layer 3 to layer 2 mappings over these Frame
Relay connections.
" Do not configure static layer 3 to layer 2 mappings between the spokes.
2 Points
2.3. Point-to-Point
" Configure the Frame Relay circuit between R6 and BB1 per the diagram.
" Do not use dynamic protocol mappings over this link.
2 Points
3. HDLC/PPP
3.1. PPP
" Configure PPP encapsulation on the Serial link between R4 and R5.
" R4 and R5 should authenticate each other across this link. Both R4 and
R5 should send their hostname along with the hash value that represents
that password CISCO.
" Configure R4 so that it will not respond to a CHAP authentication request
before R5 has been successfully authenticated.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 353 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
4. Interior Gateway Routing
4.1. OSPF
" Configure OSPF area 0 on the Frame Relay connection between R3, R4,
and R5.
" Configure your network so that R3 and R4 gain reachability to each other
over the Frame Relay network through layer 3 routing instead of static
layer 3 to layer 2 resolution.
" Advertise VLAN 44 into OSPF area 0.
3 Points
4.2. OSPF
" Configure OSPF area 568 on VLAN 568 between R5, R6, and SW2.
" R5 should be elected for as the DR for this segment.
" In the case that R5 goes down R6 should assume the role of the DR.
3 Points
4.3. OSPF
" Recently a Windows host on VLAN 568 running OSPF injected false
information into your routing domain and caused a traffic black hole. In
response to this you have put a new policy in place which states that all
adjacencies in OSPF area 568 must be authenticated with a secure hash
value.
" In addition to this configure your network so that unauthorized devices
cannot intercept OSPF hello packets as they are transiting VLAN 568.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 354 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
4.4. OSPF
" Configure OSPF area 0 on the PPP link between R4 and R5.
" The PPP link between R4 and R5 will be a backup of the Frame Relay
circuit between them. Configure the network in such a way that this link is
only used if R4 loses its connection to the Frame Relay cloud.
3 Points
4.5. OSPF
" Administrators of your network have been noticing inconsistencies with the
OSPF database when the PPP link is being used. After further
investigation they have determined that congestion on this link has been
preventing LSAs from correctly propagating. In order to deal with this
problem your design team has suggested that you increase the estimated
time required to send a link-state update packet on this interface to 5
seconds.
" Additionally they have suggested that if an acknowledgement for an LSA
sent across this interface is not received within 10 seconds, the LSA
should be retransmitted.
" Configure the network to reflect this recommendation.
2 Points
4.6. OSPF
" Advertise the Loopback 0 interfaces of R3, R4, R5, R6 and SW2 into
OSPF.
" These networks should appear in the routing table of all OSPF speaking
devices with a subnet mask of /24.
" Do not use the ip ospf network command to accomplish this.
2 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 355 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
5. Exterior Gateway Routing
5.1. BGP Peering
" Configure BGP on the following devices with the following AS numbers:
Device BGP AS
R1 300
R2 300
R3 200
R4 100
R5 100
R6 100
SW1 300
SW2 100
BB1 54
BB2 254
BB3 54
" Configure the BGP peering sessions as follows:
Device 1 Device 2
R6 BB1
R6 R5
R5 SW2
R5 R4
R5 R3
R3 BB2
R3 BB3
R3 R1
R3 R2
R1 R2
R1 SW1
R2 SW1
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 356 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
" Ensure that the BGP peering session between R4 & R5 remains up even
if R4 loses its connection to the Frame Relay cloud.
" Due to previous problems with false information being injected into the
BGP domain, AS 254 now requires all BGP peering relationships to be
authenticated with a secure hash value of the password CISCO.
" Configure R3 to reflect this policy.
" Recently AS 200 acquired R3 from AS 100. AS 100 s previous customer,
AS 54, has yet to update its configuration. Configure your network so that
R3 still appears to be in AS 100 from the perspective of BB3. Ensure that
you configure this peering relationship in such a way that AS 100 can still
use AS 200 as transit to get to AS 54.
4 Points
5.2. BGP Advertisements
" Advertise VLANs 4, 5, 7, 8, 77, 88, and 127 into the BGP domain.
" Advertise the Frame Relay network between R1, R2, and R3 into BGP.
" Advertise the Loopback 0 interfaces of R1, R2, and SW1 into BGP.
" All of these prefixes should have an origin code of incomplete after being
advertised into BGP.
2 Points
5.3. BGP Filtering
" Since AS 300 s only upstream peer is AS 200, it does not need specific
forwarding information about the rest of the BGP domain.
" Configure your network so that AS 300 sees only a default route from R3,
as well as prefixes originated by AS 200 s directly connected customers.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 357 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
5.4. BGP Bestpath Selection
" Configure AS 300 so that all traffic destined for VLAN 7 enters the Frame
Relay circuit between R1 and R3 while all traffic destined for VLAN 77
enters the Frame Relay circuit between R2 and R3.
" R3 should load balance traffic destined for VLAN 127 amongst both
Frame Relay connections to AS 300.
3 Points
5.5. BGP Aggregation
" In order to help reduce the size of the global BGP table AS 200 has
decided to aggregate all networks learned from their customers.
" Configure R3 to originate an aggregate prefix that represents all of the
VLANs that have been originated into BGP.
" R3 should not advertise any subnets which make up this aggregate to any
neighbor.
3 Points
5.6. BGP Aggregation
" Shortly after configuring this aggregation policy engineers in AS 200
began to notice odd patterns with traffic destined to this aggregate block.
Apparently the aggregate prefix originated by AS 200 is getting passed on
from AS 100 to AS 54. Then AS 54 is sending traffic to AS 100 for which
the longest match is the aggregate block. This in turn causes AS 100 to
forward the traffic back to AS 200 where it is eventually dropped. In
response to this your engineers have decided to send AS 100 only the
subnets instead of the aggregate, but still send only the aggregate to all
other peers.
" Configure AS 200 to reflect this policy.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 358 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
5.7. BGP Aggregation
" While this seemed like a good idea on the surface a new problem has now
arisen. Since AS 100 is peering with AS 54 it is learning the aggregate
block which is advertised from AS 200 to AS 54. Since the aggregate
appears to have originated in AS 200, AS 100 is accepting it as a valid
prefix. Now AS 100 is sending traffic that it does not have a longer match
for to AS 54, which in turn forwards the traffic back to AS 200 where it is
eventually dropped. This behavior has left the engineers on your ISP
team scratching their heads. Finally your network team has devised the
following solution for you to implement:
o When originating the aggregate address AS 200 should include an
ordered set of the autonomous systems from which the subnets
were originated. Therefore AS 100 cannot accept the prefix from
AS 54 due to its own AS being in the path.
o Furthermore since AS 300 will not accept a prefix that has its own
AS in the path, the aggregate should only include AS 100 in the
ordered set.
" Configure R3 to reflect this policy.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 359 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
6. Multicast
6.1. PIM
" Configure IP Multicast routing on R1, R2, R3, R4, R5, and SW1.
" Configure PIM sparse mode on the following interfaces:
Device Interface
R1 Fa0/0
R1 S0/0
R2 Fa0/0
R2 S0/0
R3 S1/0
R3 S1/1
R4 E0/1
R4 S0/0
R5 E0/0
R5 S0/0
SW1 VL7
SW1 VL77
SW1 VL127
3 Points
6.2. RP Assignment
" Configure SW1 to announce itself as a Rendezvous Point for the PIM
domain.
" R3 should be responsible for group to RP mappings.
3 Points
6.3. Multicast Testing
" A multicast server located in VLAN 7 will be sending feeds to users in
VLANs 4 and 5. In order to ensure that this configuration will be functional
configure the network so that R4 and R5 respond to ICMP echo requests
sent to the group address 224.1.1.1 sent from VLAN 7.
" Do not use tunneling or static RP assignments to accomplish this.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 360 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
7. IPv6
7.1. IPv6 Addressing
" Configure IPv6 on R3 s connection to VLAN 32 using the address
2001:192:10:X::/64.
" Configure IPv6 on the Frame Relay circuit between R1, R2, and R3 using
the network 2001:149:X:123::/64.
" Configure IPv6 on VLAN 127 between R1 and R2 using the network
2001:149:X:127::/64.
" Hosts in VLAN 127 should use R1 as their default gateway.
3 Points
7.2. RIPng
" Configure RIPng on all segments running IPv6.
" Hosts on VLAN 127 should prefer to use the Frame Relay PVC between
R1 and R3 to reach prefixes learned from BB2.
" If this circuit is down they should be rerouted to R2 s PVC to R3.
3 Points
8. QoS
8.1. Frame Relay Traffic Shaping
" Recently you have been noticing drops on R3 s Frame Relay PVC which
connects to R2. Apparently your level 1 administrators failed to take into
account the difference in port speeds between R2 s 64Kbps interface and
R3 s T1 interface when configuring this circuit.
" In order to help alleviate congestion configure Frame Relay Traffic
Shaping on R3 to reduce its average output rate on the circuit.
" R3 should attempt to average on output rate of 64Kbps on this circuit.
" In the case that R3 has accumulated credit it should be allowed to send a
maximum of 12Kb of data in a single interval.
" Use the default Tc for this circuit.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 361 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
8.2. Frame Relay Traffic Shaping
" Further monitoring of R3 s Frame Relay circuit to R2 has indicated that the
issue has been resolved. However now you have been getting complaints
from users on VLAN 127 about horrible network response time. The
complaints seem to have been coming from users on VLAN 127 that are
using R1 as their default gateway. After speaking with the rest of your
network team, it seems that no other recent configuration changes have
been made regarding this circuit.
" Configure your network to resolve this problem.
3 Points
9. Security
9.1. Traffic Policing
" Recent traffic monitoring in your network has indicated a suspiciously high
amount of ICMP packets being received on R6 s Frame Relay circuit to
BB1. After further investigation it appears as though your network is
undergoing a DoS attack.
" In order to reduce the impact of this attack on the rest of your internal
network configure R6 to police all ICMP traffic received from BB1 to 8Kbps
with the minimum possible burst.
" Do not use an access-list to accomplish this.
3 Points
9.2. Address Spoofing
" After reviewing your log files you have determined that the DoS attack
came from hosts with spoofed private addresses.
" To help prevent this type of attack in the future configure your network so
that traffic will not be accepted from BB1 if it has been originated from
these hosts.
2 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 362 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
10. System Management
10.1. IOS Image Management
" Recently a security auditor downloaded all of your devices configuration
files via TFTP. Subsequently management has decided that TFTP is too
insecure of a method to backup your devices configurations. You have
been tasked with setting up R3 to test out the new FTP server that will be
used to backup devices configurations.
" The FTP server's IP address is 149.X.5.100.
" The username for R3 to use is R3FTP and the password is CISCO.
" For security reasons you have setup the FTP server to only accept FTP
sessions sourced from R3's Loopback 0 interface.
" Configure R3 to meet these requirements.
3 Points
10.2. Logging
" You have been tasked with setting up the edge routers (R3 & R6) with the
following logging parameters:
o The console should receive all severity 6 and below messages
o Console messages should be rate-limited to 5 per second
o Log severity 4 messages and below and store them in the routers
buffer
o When users telnet in and execute the terminal monitor command
they should receive all messages except "debugging"
3 Points
11. IP Services
11.1. Line in Use Message
" Configure R5's VTY lines to display a "Line in Use" message of "Try back
in 10 minutes" when an incoming telnet connection is attempted but all
lines are full.
2 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 363 -
CCIE Routing & Switching Lab Workbook Version 4.0 Lab 19
11.2. Banner Messages
" Configure R5 so that when users telnet in the following banner is
displayed where X is the incoming line number:
R5 is for use by authorized users only. You are on line
number: X.
" Do not enter the line number statically.
2 Points
11.3. HSRP
" Configure HSRP on R1 and R2 for hosts on VLAN 127 using the group
name HSRP.
" These hosts will have their default gateway set to the IP address
149.X.127.254.
" R1 should be the preferred gateway unless it loses its connection to the
Frame Relay cloud.
3 Points
11.4. DHCP Relay
" Configure R1 and R2 to forward DHCP requests from users on VLAN 127
to your DHCP server with the IP address 149.X.5.50.
" Ensure that only the active HSRP router forwards the DHCP request to
this server.
3 Points
Copyright © 2007 Internetwork Expert www.InternetworkExpert.com
- 364 -
Wyszukiwarka
Podobne podstrony:
IE RS lab 18 overviewIE RS lab 13 overviewIE RS lab 10 overviewIE RS lab 12 overviewIE RS lab 14 overviewIE RS lab 19 diagramIE RS lab 20 overviewIE RS lab 17 overviewIE RS Lab 16 overviewIE RS lab 15 overviewIE RS lab 9 overviewIE RS lab 8 overviewIE RS lab 18 DiagramIE RS lab 13 solutionsIE RS lab 17 diagramIE RS lab 8 diagramIE RS lab 14 solutionsIE RS lab 10 diagramwięcej podobnych podstron