Fanuc 0T Okuma [VT] L255 82


{Change Comments ***********************************************************}

{1/29/90, Updated: Fanuc 0T-Miyano L008.52 to .69 format, JR}
{7/24/90, Added InitProg globally to posts with this remark, DWB}
{9/25/90, Updated to Version 3.2 per Fanuc 10T MS [-] L001.71.1 Format, DWB}
{10/2/90, Added StockOff globally at FirstOperation, DWB}
{10/8/90, Replace CalcRPM2 globally with CalcEPRPM# at end of prog, DWB}

{3/27/91
Modified: Fanuc 0T/3T Miyano L008.71.3
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 10T MS [-] L001.80 Format.
All normal Fanuc Canned Cycles are supported.
Added Math to calculate start of Tapered Thread for AutoFinish.
DWB}

{4/17/91
Modified: Fanuc 0T/3T Miyano L008.80
Replaced AbsOrInc command with SetAbs, in FirstOperation, and changed MoveType$ to 'ABSOLUTE'.
DWB}

{8/5/91
Updated: Fanuc 0T/3T Miyano L008.81
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.82 Format.
KM}

{3/30/90
Updated: Fanuc 0T/3T Miyano L008.82
For: Gibbs & Associates
Corrected RoughContour Approach Bug.
3TCs and 0Ts do not support the Type II hill and valley contour.
Approach must be only X-axis for OD and ID Approaches, and Z-axis for Face Approaches.
Modified output of Speed & ConstantSurfaceFeed for SameTool in CheckOffset sub.
Added Logic to suppress Feed and FeedRate for Approaches.
Added bypass of AutoFinish for Non-Canned RoughSimple Operations.
DWB}

{4/16/91
Copied & modified: Fanuc 0T/3T Miyano L008.82.1
For: Valley Todeco
Machine: Okuma
Machine is like 2 lathes in one. It has 2 Spindles each with its own turret.
They can be run independently of each other or can be run simultainiusly.
Control has a Left/Right switch for maipulation of either side.
The processor should be written as if its just a regular lathe, nothing special.
Control: Fanuc 0T
Modifications to the beginning and ending of tools.
Using G50 Home preset.
Using G28 for index position.
This is a first draft per customer requests.
Jim Radcliffe}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.####;0.'
#3 = '#######0'
#4 = '###^##0'
#5 = '#.######;0.'
#6 = '###0'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ADD#,2)
FORMAT(SPX#,2)
FORMAT(SPZ#,2)
FORMAT(FinishXDia#,2)
FORMAT(Taper#,2)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Program#,3) {.72}
FORMAT(Operation#,3) {.72}
FORMAT(Tool#,3) {.72}
FORMAT(Dwell#,4) {.72}
FORMAT(FeedIPR#,5)
FORMAT(CalcEPRPM#,6)

{Prog Subroutines **********************************************************}

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
END
RETURN

PSInit: {reset flags from last Op, .70}
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN

ODApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XStockMax#
SeqLabC Feed XSPC FeedRate EOL
END
RETURN

IDApproachSP:
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL { for SameTool ApproachID }
StockOnNoCan
IF NotEqual? CycleStartX# XStockMax#
SeqLabC Feed XSPC FeedRate EOL
END
RETURN

FaceApproachSP:
SeqLabC StockOnNoCan XSPC EOL { for SameTool ApproachFace }
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZStockMax#
SeqLabC Feed ZSPC FeedRate EOL
END
RETURN

AppMove:
ZCP OpToolID LatheOffset
RETURN

Approach: { NOT FOR TAILSTOCK, .82 }
IF ApproachOD?
SeqLabC Rapid XCP AppMove EOL
ODApproachSP
ELSE
IF ApproachID?
SeqLabC Rapid XOpCD AppMove EOL
IDApproachSP
ELSE {ApproachFace}
SeqLabC Rapid StockOnNoCan XSP StockOff AppMove EOL
FaceApproachSP
END
END
RETURN

CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
IF NewToolOffset?
SeqLabC LOfstOff '00' EOL
SeqLabC OpToolID LatheOffset EOL
END
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
ELSE
SeqLabC Preset MaxRPM EOL
SeqLabC CSSOn 'G96' Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
SeqLabC CSSOff 'G97' Speed
END
END
IF LAST ProgStop?
SeqLabC SpeedC SpinOn EOL
SeqLabC CoolOn EOL
ELSE
SeqLabC SpeedC EOL
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
DoPostScript
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
ELSE
IF CannedCycle?
SeqLab
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN

CheckRapid:
IF LAST CannedCycle?
Rapid
ELSE
RapidC
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
SetAbs
PosSideLathe
StandardXZArcs
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ABSOLUTE INCHES )' EOL
END
END
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
OpenSub
StockOff {.71.2}
SetHome
DoOpComments
DoPostScript
Plane
SeqLab Rapid 'G28U0.W0.' OpToolID '00' EOL
SeqLabC Preset Home MaxRPM EOL
SeqLabC CoolOn EOL
SeqLabC CSSOff 'G97'
IF ConstantSurfaceFeed?
CalcRPM1
ELSE
Speed
END
SpinOn EOL
Approach
ELSE
IF NewTool?

{Finish off last Operation}

StockOff {.62}
CheckRapid
IF LAST ApproachOD?
SeqLabC XCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC ZCPC EOL
DoEndOpPS
IF LAST ConstantSurfaceFeed?
SeqLabC CSSOff 'G97' CalcRPM2 EOL
END
SeqLabC 'G28U0.W0.' LOfstOff '00'
IF LAST ProgStop?
'M0' EOL
ELSE
ProgStop EOL
END
' ' EOL

{Start new Operation}

DoOpComments
DoPostScript
SeqLab Rapid 'G28U0.W0.' OpToolID '00' EOL
SeqLabC Preset Home MaxRPM EOL
SeqLabC CoolOn EOL
SeqLabC CSSOff 'G97'
IF ConstantSurfaceFeed?
CalcRPM1
ELSE
Speed
END
SpinOn EOL
Approach
ELSE
IF SameTool? {.62}

{Start new Operation}

StockOff
DoOpComments
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC ZCPC EOL
SeqLabC XCPC EOL
END
CheckOffset
ODApproachSP
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC XCPC EOL
END
SeqLabC ZCPC EOL
SeqLabC XOpCDC EOL
END
CheckOffset
IDApproachSP
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC XCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC ZCPC EOL
END
CheckOffset
FaceApproachSP
END
END
END
END
END
END {common point for all operations}
IF ConstantSurfaceFeed? AND NOT SameTool?
SeqLabC CSSOn 'G96' Speed EOL
END
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
IF ApproachFace?
SeqLabC LCycle 'Z' FirstMoveEPZ# XatFinZ XTapAtZ FeedRate EOL
ELSE
SeqLabC LCycle XatFinZ FinZ XTapAtZ FeedRate EOL
END
SimpleRough
ELSE
TagInc
IF RoughContour?
SetPass2
SeqLabC LCycle CutDepth EOL
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft FeedRate EOL
'>' Tag# EOL
IF ApproachFace?
SeqLab StepMove 'Z' SPZ# EOL
SeqLabC 'X' SPX# EOL
ELSE
SeqLab StepMove 'X' SPX# EOL
SeqLabC 'Z' SPZ# EOL
END
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
ELSE
IF RoughPatternShift?
SetPass2
SeqLabC LCycle XminusU ZminusW NumCuts EOL
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft FeedRate EOL
'>' Tag# EOL
SeqLab Rapid StrtPos EOL
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
END
END
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
SeqLabC LCycle XatFinZ FinZ XTapAtZ CutMethod ThrdHeight CutDepth ThrdLead ToolAngle EOL
IF AutoFinish?
IF Taper?
SeqLabC Rapid
'X' ADD# FinishXDia# MUL# Taper# NumSc#('2') { Outputs start of Taper }
EOL
SeqLabC 'G32' XatFinZ FinZ ThrdLead EOL
ELSE
SeqLabC Rapid XatFinZ EOL
SeqLabC 'G32' FinZ ThrdLead EOL
END
SeqLabC Rapid XCSP EOL
SeqLabC ZCSP EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF PeckChipBreaker?
SeqLabC LCycle ZDepth RLevel Dwell Peck Retract FeedRate EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish?
IF NOT Drilling? AND NOT Grooving? AND NOT RoughSimple?
StockOff
IF Turning?
SetPass1
ELSE
SetPass2
END
SeqLabC RapidC StrtPos EOL
ToolPath
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
StockOff
IF CannedCycle?
Rapid
ELSE
RapidC
END
IF ApproachOD?
SeqLabC XCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC ZCPC EOL
DoEndOpPS
IF ConstantSurfaceFeed?
SeqLabC CSSOff 'G97S' CalcEPRPM# EOL
END
SeqLabC 'G28U0.W0.' OpToolID '00' EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END


Wyszukiwarka

Podobne podstrony:
Fanuc 0T Yam CK1A L336 82 1
Fanuc 0T Azuma MSI L245 82 2
Fanuc 0T Okuma [CM] L318 85 1
Fanuc 0T Ikegai [TSS] L348 82 3
Fanuc 0T Okuma [WB] L300 85
Fanuc 0T Miyano [TPM] L329 82 3
Fanuc 0T Okuma [SP] L728 85 3
Fanuc 0T MS ( G30) L212 82 1
Fanuc 0T MS SL25A L239 82 5
Fanuc 0T (Anzon1) L077 82 1m
Fanuc 0T SL 25 [CS] L323 82 1
Fanuc 0T Miy BND 34 L313 82 2
Fanuc 0T Miyano [A&B] L247 82 6
Fanuc 0T Nakamora L248 82
Fanuc 0T [RWMT] L369 82 2

więcej podobnych podstron